Modernization of protection and control system of HV/MV substation in Russia

This work describes different possibilities of protection and control system improvement of primary distribution substation. The status of condition and main problems of power networks from reliability point of view in Russia are described. This work studies technologies used today in Russia for protection of distribution networks with their disadvantages. Majority of medium voltage networks (6-35 kV) has isolated network point. There is still no any protection available on the market which allows to estimate distance to fault in case of earth fault. The thesis analyses methods of earth fault distance calculation. On the basis of computer simulation the influence of various factors on calculation accuracy is studied. The practical implementation of the method presupposes usage of digital relay. Application of digital relay is accompanied by numerous opportunities which are described in this work. Also advantages of system implemented on the basis of IEC 61850 standard are examined. Finally, suitability of modern digital relays from GOST standard point of view is analyzed.

Planning and ramping up a new SW Testing site

During recent years, mobile phone markets have changed significantly. Asian markets have become vital for the manufacturers with their millions of end users and multiple major mobile network operators. This has resulted in software development as global companies have research and development sites running in multiple locations, including Asia. The reasons behind this are not only in reducing labor costs but also in capitalizing on the local knowledge and knowhow. A ramp-up site has multiple effects in the software development and software release activities. This thesis focuses on representing the importance of software testing as part of software development process and highlighting issues that need to be considered during ramp-up activities. In addition this work tries to emphasize the importance of communication between parties and information gathering prior to setting up the ramp-up site. The output of this thesis was successful software testing site ramp-up within the set time limits. The quality of software testing work was assured and the ramp-up -project requirements were achieved.

Effect of hydrodynamics on modelling, monitoring and control of crystallization

Crystallization is a purification method used to obtain crystalline product of a certain crystal size. It is one of the oldest industrial unit processes and commonly used in modern industry due to its good purification capability from rather impure solutions with reasonably low energy consumption. However, the process is extremely challenging to model and control because it involves inhomogeneous mixing and many simultaneous phenomena such as nucleation, crystal growth and agglomeration. All these phenomena are dependent on supersaturation, i.e. the difference between actual liquid phase concentration and solubility. Homogeneous mass and heat transfer in the crystallizer would greatly simplify modelling and control of crystallization processes, such conditions are, however, not the reality, especially in industrial scale processes. Consequently, the hydrodynamics of crystallizers, i.e. the combination of mixing, feed and product removal flows, and recycling of the suspension, needs to be thoroughly investigated. Understanding of hydrodynamics is important in crystallization, especially inlargerscale equipment where uniform flow conditions are difficult to attain. It is also important to understand different size scales of mixing; micro-, meso- and macromixing. Fast processes, like nucleation and chemical reactions, are typically highly dependent on micro- and mesomixing but macromixing, which equalizes the concentrations of all the species within the entire crystallizer, cannot be disregarded. This study investigates the influence of hydrodynamics on crystallization processes. Modelling of crystallizers with the mixed suspension mixed product removal (MSMPR) theory (ideal mixing), computational fluid dynamics (CFD), and a compartmental multiblock model is compared. The importance of proper verification of CFD and multiblock models is demonstrated. In addition, the influence of different hydrodynamic conditions on reactive crystallization process control is studied. Finally, the effect of extreme local supersaturation is studied using power ultrasound to initiate nucleation. The present work shows that mixing and chemical feeding conditions clearly affect induction time and cluster formation, nucleation, growth kinetics, and agglomeration. Consequently, the properties of crystalline end products, e.g. crystal size and crystal habit, can be influenced by management of mixing and feeding conditions. Impurities may have varying impacts on crystallization processes. As an example, manganese ions were shown to replace magnesium ions in the crystal lattice of magnesium sulphate heptahydrate, increasing the crystal growth rate significantly, whereas sodium ions showed no interaction at all. Modelling of continuous crystallization based on MSMPR theory showed that the model is feasible in a small laboratoryscale crystallizer, whereas in larger pilot- and industrial-scale crystallizers hydrodynamic effects should be taken into account. For that reason, CFD and multiblock modelling are shown to be effective tools for modelling crystallization with inhomogeneous mixing. The present work shows also that selection of the measurement point, or points in the case of multiprobe systems, is crucial when process analytical technology (PAT) is used to control larger scale crystallization. The thesis concludes by describing how control of local supersaturation by highly localized ultrasound was successfully applied to induce nucleation and to control polymorphism in reactive crystallization of L-glutamic acid.

Analysis and Control of Excitation, Field Weakening and Stability in Direct Torque Controlled Electrically Excited Synchronous Motor Drives

Direct torque control (DTC) is a new control method for rotating field electrical machines. DTC controls directly the motor stator flux linkage with the stator voltage, and no stator current controllers are used. With the DTC method very good torque dynamics can be achieved. Until now, DTC has been applied to asynchronous motor drives. The purpose of this work is to analyse the applicability of DTC to electrically excited synchronous motor drives. Compared with asynchronous motor drives, electrically excited synchronous motor drives require an additional control for the rotor field current. The field current control is called excitation control in this study. The dependence of the static and dynamic performance of DTC synchronous motor drives on the excitation control has been analysed and a straightforward excitation control method has been developed and tested. In the field weakening range the stator flux linkage modulus must be reduced in order to keep the electro motive force of the synchronous motor smaller than the stator voltage and in order to maintain a sufficient voltage reserve. The dynamic performance of the DTC synchronous motor drive depends on the stator flux linkage modulus. Another important factor for the dynamic performance in the field weakening range is the excitation control. The field weakening analysis considers both dependencies. A modified excitation control method, which maximises the dynamic performance in the field weakening range, has been developed. In synchronous motor drives the load angle must be kept in a stabile working area in order to avoid loss of synchronism. The traditional vector control methods allow to adjust the load angle of the synchronous motor directly by the stator current control. In the DTC synchronous motor drive the load angle is not a directly controllable variable, but it is formed freely according to the motor’s electromagnetic state and load. The load angle can be limited indirectly by limiting the torque reference. This method is however parameter sensitive and requires a safety margin between the theoretical torque maximum and the actual torque limit. The DTC modulation principle allows however a direct load angle adjustment without any current control. In this work a direct load angle control method has been developed. The method keeps the drive stabile and allows the maximal utilisation of the drive without a safety margin in the torque limitation.

Approaches to Supply Chain Risk Management: Identification, Analysis and Control

Supply chain risk management has emerged as an increasingly important issue in logistics as disruptions in the supply chain have become critical issues for many companies. The scientific literature on the subject is developing and in many respects the understanding of it is still in its infancy. Thus, there is a need for more information in order for scholars and practitioners to understand the causalities and interrelations that characterise the phenomenon. The aim of this dissertation is to narrow this gap by exploring key aspects of supply chain risk management through two maritime supply chains in the immediate region of the Gulf of Finland. The study contributes to the field in three different ways. Firstly, it facilitates the identification of risks on different levels of the supply chain through a systematic analysis of the processes and actors, and of the cognitive barriers that limit the actors’ visibility and their understanding of the operations and the risks involved. There is a clear need to increase collaboration and information exchange in order to improve visibility in the chain. Risk management should be a collaborative effort among the individual actors, aimed at obtaining a holistic picture. Secondly, the study contributes to the literature on risk analysis through the use of systemic frameworks that illustrate the causalities and linkages in the system, thereby making it easier to perceive the vulnerabilities. Thirdly, the study enhances current knowledge of risk control in identifying actor roles, risk visibility and risk controllability as being among the key factors determining risk-management effectiveness against supply-chain vulnerability. This dissertation is divided into two parts. The first part gives a general overview of the relevant literature, the research design and the conclusions of the study, and the second part comprises six research publications. Case-study methodology with systematic combining approach is used, where in-depth interviews, questionnaires and expert panel sessions are the main data collection methods. The study illustrates the current state of risk management in multimodal maritime supply chains, and develops frameworks for further analysis. The results imply that there are major differences between organizations in their ability to execute supply chain risk management. Further collaboration should be considered in order to facilitate the development of systematic and effective management processes.

Field-Programmable Gate Array Card for Readout and Control of Cryoelectronics

The main goal of the present Master’s Thesis project was to create a field-programmable gate array (FPGA) based system for the control of single-electron transistors or other cryoelectronic devices. The FPGA and similar technologies are studied in the present work. The fixed and programmable logic are compared with each other. The main features and limitations of the hardware used in the project are investigated. The hardware and software connections of the device to the computer are shown in detail. The software development techniques for FPGA-based design are described. The steps of design for programmable logic are considered. Furthermore, the results of filters implemented in the software are illustrated.

Design and Control of Permanent Magnet Synchronous Machine for Hybrid Electric Vehicle

This master’s thesis mainly focuses on the design requirements of an Electric drive for Hybrid car application and its control strategy to achieve a wide speed range. It also emphasises how the control and performance requirements are transformed into its design variables. A parallel hybrid topology is considered where an IC engine and an electric drive share a common crank shaft. A permanent magnet synchronous machine (PMSM) is used as an electric drive machine. Performance requirements are converted into Machine design variables using the vector model of PMSM. Main dimensions of the machine are arrived using analytical approach and Finite Element Analysis (FEA) is used to verify the design and performance. Vector control algorithm was used to control the machine. The control algorithm was tested in a low power PMSM using an embedded controller. A prototype of 10 kW PMSM was built according to the design values. The prototype was tested in the laboratory using a high power converter. Tests were carried out to verify different operating modes. The results were in agreement with the calculations.

Modeling and Control of the Power Conversion Unit in a Solid Oxide Fuel Cell Environment

In this doctoral thesis, a power conversion unit for a 10 kWsolid oxide fuel cell is modeled, and a suitable control system is designed. The need for research was identified based on an observation that there was no information available about the characteristics of the solid oxide fuel cell from the perspective of power electronics and the control system, and suitable control methods had not previously been studied in the literature. In addition, because of the digital implementation of the control system, the inherent characteristics of the digital system had to be taken into account in the characteristics of the solid oxide fuel cell (SOFC). The characteristics of the solid oxide fuel cell as well the methods for the modeling and control of the DC/DC converter and the grid converter are studied by a literature survey. Based on the survey, the characteristics of the SOFC as an electrical power source are identified, and a solution to the interfacing of the SOFC in distributed generation is proposed. A mathematical model of the power conversion unit is provided, and the control design for the DC/DC converter and the grid converter is made based on the proposed interfacing solution. The limit cycling phenomenon is identified as a source of low-frequency current ripple, which is found to be insignificant when connected to a grid-tied converter. A method to mitigate a second harmonic originating from the grid interface is proposed, and practical considerations of the operation with the solid oxide fuel cell plant are presented. At the theoretical level, the thesis discusses and summarizes the methods to successfully derive a model for a DC/DC converter, a grid converter, and a power conversion unit. The results of this doctoral thesis can also be used in other applications, and the models and methods can be adopted to similar applications such as photovoltaic systems. When comparing the results with the objectives of the doctoral thesis, we may conclude that the objectives set for the work are met. In this doctoral thesis, theoretical and practical guidelines are presented for the successful control design to connect a SOFC-based distributed generation plant to the utility grid.

Virtual technology and haptic interface solutions for design and control of mobile working machines

Commercially available haptic interfaces are usable for many purposes. However, as generic devices they are not the most suitable for the control of heavy duty mobile working machines like mining machines, container handling equipment and excavators. Alternative mechanical constructions for a haptic controller are presented and analysed. A virtual reality environment (VRE) was built to test the proposed haptic controller mechanisms. Verification of an electric motor emulating a hydraulic pump in the electro-hydraulic system of a mobile working machine is carried out. A real-time simulator using multi-body-dynamics based software with hardware-in-loop (HIL) setup was used for the tests. Recommendations for further development of a haptic controller and emulator electric motor are given.

Oxalic acid and calcium oxalate in production of wood-containing paper : formation, analysis, and control

Papperstillverkningen störs ofta av oönskade föreningar som kan bilda avsättningar på processytor, vilket i sin tur kan ge upphov till störningar i pappersproduktionen samt försämring av papperskvaliteten. Förutom avsättningar av vedharts är stenliknande avlagringar av svårlösliga salter vanliga. I vårt dagliga liv är kalkavlagringar i kaffe- och vattenkokare exempel på liknande problem. I massa- och pappersindustrin är en av de mest problematiska föreningarna kalciumoxalat; detta salt är nästan olösligt i vatten och avlagringarna är mycket svåra att avlägsna. Kalciumoxalat är också känt som en av orsakerna till njurstenar hos människor. Veden och speciellt barken innehåller alltid en viss mängd oxalat men en större källa är oxalsyra som bildas när massan bleks med oxiderande kemikalier, t.ex. väteperoxid. Kalciumoxalat bildas när oxalsyran reagerar med kalcium som kommer in i processen med råvattnet, veden eller olika tillsatsmedel. I denna avhandling undersöktes faktorer som påverkar bildningen av oxalsyra och utfällningen av kalciumoxalat, med hjälp av bleknings- och utfällningsexperiment. Forskningens fokus låg speciellt på olika sätt att förebygga uppkomsten av avlagringar vid tillverkning av trähaltigt papper. Resultaten i denna avhandling visar att bildningen av oxalsyra samt utfällning av kalciumoxalat kan påverkas genom processtekniska och våtändskemiska metoder. Noggrann avbarkning av veden, kontrollerade förhållanden under den alkaliska peroxidblekningen, noggrann hantering och kontroll av andra lösta och kolloidala substanser, samt utnyttjande av skräddarsydd kemi för kontroll av avlagringar är nyckelfaktorer. Resultaten kan utnyttjas då man planerar blekningssekvenser för olika massor samt för att lösa problem orsakade av kalciumoxalat. Forskningsmetoderna som användes i utfällningsstudierna samt för utvärdering av tillsatsmedel kan också utnyttjas inom andra områden, t.ex. bryggeri- och sockerindustrin, där kalciumoxalatproblem är vanligt förekommande. -------------------------------------------- Paperinvalmistusta häiritsevät usein erilaiset epäpuhtaudet, jotka kiinnittyvät prosessipinnoille ja haittaavat tuotantoa sekä paperin laatua. Puun pihkan lisäksi eräs yleinen ongelma on niukkaliukoisten suolojen aiheuttamat kivettymät. Kalkkisaostuma kahvinkeittimessä on esimerkki vastaavasta ongelmasta arkielämässä. Massa- ja paperiteollisuudessa yksi hankalimmista kivettymien muodostajista on kalsiumoksalaatti, koska se on lähes liukenematonta ja sen aiheuttamat saostumat ovat erittäin vaikeasti poistettavia. Kalsiumoksalaatti on yleisesti tunnettu myös munuaiskivien aiheuttajana ihmisillä. Puu ja varsinkin sen kuori sisältää aina jonkin verran oksalaattia, mutta suurempi lähde on kuitenkin oksaalihappo jota muodostuu valkaistaessa massaa hapettavilla kemikaaleilla, kuten vetyperoksidilla. Kalsiumoksalaattia syntyy kun veden, puun ja lisäaineiden mukana prosessiin tuleva kalsium reagoi oksalaatin kanssa. Tässä väitöskirjatyössä tutkittiin oksaalihapon muodostumiseen ja kalsiumoksalaatin saostumiseen vaikuttavia tekijöitä valkaisu- ja saostumiskokeiden avulla. Tutkimuksen painopiste oli saostumien ehkäisemisessä puupitoisten painopaperien valmistuksessa. Työssä saadut tulokset osoittavat että oksaalihapon muodostumiseen ja kalsiumoksalaatin saostumiseen voidaan vaikuttaa sekä prosessiteknisten että märänpään kemian keinojen avulla. Tehokas puun kuorinta, optimoidut olosuhteet peroksidivalkaisussa, muiden liuenneiden ja kolloidisten aineiden hallinta sekä räätälöidyn kemian hyödyntäminen kalsiumoksalaattisaostumien torjunnassa ovat keskeisissä rooleissa ongelmien välttämiseksi. Väitöskirjatyön tuloksia voidaan hyödyntää massan valkaisulinjoja suunniteltaessa sekä kalsiumoksalaatin aiheuttamien ongelmien ratkaisemisessa. Tutkimusmenetelmiä, joita käytettiin saostumiskokeissa ja eri lisäaineiden vaikutusten arvioinnissa, voidaan hyödyntää massa- ja paperiteollisuuden lisäksi myös muilla alueilla, kuten sokeri- ja panimoteollisuudessa, joissa ongelma on myös yleinen.

Planning and implementation of entrepreneurial marketing processes in SMEs

Entrepreneurial marketing is newly established term and there is need for more specific studies in order to understand the concept fully. SMEs have entrepreneurial marketing elements more visible in their marketing and therefore provide more fruitful insights for this research. SMEs marketing has gained more recognition during the past years and in some cases innovative characteristics can be identified despite constraints such as lack of certain resources. The purpose of this research is to study entrepreneurial marketing characteristics and SME processes in order to wider understanding and gain more insights of entrepreneurial marketing. In addition, planning and implementation of entrepreneurial marketing processes is examined in order to gain full coverage of SMEs marketing activities. The research was conducted as a qualitative research and data gathering was based on semi-structured interview survey, which involved nine company interviews. Multiple case research was used to analyze data so that focus and clarity could be maintained in organized manner. Case companies were chosen from different business fields so that more variation and insights could be identified. The empirical results suggest that two examined processes networking and word-of-mouth communication are very important processes for case companies which supports the previous researches. However, the entrepreneurial marketing characteristics had variation some were more visible and recognizable than others. Examining more closely the processes companies did not fully understand that networking or word-of-mouth marketing could be used as efficiently as other conventional marketing methods.

Capital investments planning and life cycle simulations for the new valves manufacturing facility in Russia

The focus of the research is on the derivation of the valid and reliable performance results regarding establishment and launching of the new full-scale industrial facility, considering the overall current conditions for the project realization in and out of Russia. The study demonstrates the process of the new facility concept development, with following perfor-mance calculation, comparative analyzes conduction, life-cycle simulations, performance indicators derivation and project`s sustainability evaluation. To unite and process the entire input parameters complexity, regards the interlacing between the project`s internal technical and commercial sides on the one hand, and consider all the specifics of the Russian conditions for doing business on the other hand, was developed the unique model for the project`s performance calculation, simulations and results representation. The complete research incorporates all corresponding data to substantiate the assigned facility`s design, sizing and output capacity for high quality and cost efficient ferrous pipe-line accessories manufacturing, as well as, demonstrates that this project could be suc-cessfully realized in current conditions in Russia and highlights the room for significant performance and sustainability improvements based on the indexes of the derived KPIs.