Production of Chemicals from Woody Biomass by Wet Oxidation

The production of chemicals from sawdust by wet oxidation has been investigated. Two different concentrations of sawdust; 54054 mg/l and 32683 mg/l were used in the study. The wet oxidation operating conditions were; 175 deg.C – 225 deg.C, 1MPa Oxygen, and 40 minutes to 120 minutes reaction time. Carboxylic acids were among the chemicals produced in the process. The total yield of carboxylic acids was found to increase with temperature. Also, higher yields of carboxylic acids were observed at a lower sawdust concentration. This was probably due to the high oxygen-biomass ratio at lower sawdust concentration. Higher oxygen availability at low sawdust concentration resulted in increased conversion of the sawdust; hence the higher yields of carboxylic acids. At lower sawdust concentration, a total carboxylic acid yield of 25.59 wt% was attained at 200 deg.C and 40 minutes reaction time. At higher sawdust concentration, a total carboxylic acid yield of 15.57 wt% was attained at 200 deg.C and 40-minutes reaction time. The carboxylic acids identified include formic acid, acetic acid, succinic acid and oxalic acid. The optimum temperature for the production of formic acid was found to be 200 deg.C, while the optimum temperature for the production of acetic acid was found to be 225 deg.C. A temperature of 225 deg.C and relatively short reaction time of 10 minutes was found to be the optimal condition for the production of succinic acid. Formic acid was produced in the highest yield, with an optimal yield of 13.69wt %, when the reaction temperature and time are 200 deg.C and 40 minutes respectively. The yield of formic acid was found to decrease significantly when further increasing the temperature to 225 deg.C. This was presumably due to thermal decomposition of formic acid at relatively higher temperature. However, the yield of acetic acid was found to steadily increase with temperature. This is because acetic is more thermally stable than formic acid. The yield of acetic acid did not decrease after the temperature was increased to 225 deg.C. Optimal yield of acetic acid (7.98wt %) was achieved at; 225 deg.C, and 40 minutes reaction time. Succinic acid was produced only at temperatures of 200 deg.C and 225 deg.C. Optimal yield of succinic acid (5.66wt %) was attained under the following conditions; 32683 mg/l, 225 deg.C, 1MPa O2, and 10-minutes reaction time. Oxalic acid was produced in the lowest yield and, less frequently. The optimal yield of oxalic acid (4.02 wt%) was attained at 175 deg.C and 80-minutes of reaction time The Total Organic Carbon (TOC) is found to be higher when increasing the operating temperature, thus suggesting that more organic compounds are formed at higher temperatures. The identified carboxylic acids could only account for less than 30% of the measured COD content of the various wet oxidation samples. This implies that some other unidentified compounds (reaction products) must have been present. In general, wet oxidation seems to be an effective method for converting lignocellulosic biomass into useful chemicals. Relatively higher temperatures have been found to favor the production of carboxylic acids from sawdust.

The ETH Zurich DOI Desk: DOIs as standard persistent identifier and best practice in Swiss Open Access repositories

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Leveraging open access for integrating repository data at Indiana University Libraries

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Pressurized hot water flow-through extraction of birch wood

Effective processes to fractionate the main compounds in biomass, such as wood, are a prerequisite for an effective biorefinery. Water is environmentally friendly and widely used in industry, which makes it a potential solvent also for forest biomass. At elevated temperatures over 100 °C, water can readily hydrolyse and dissolve hemicelluloses from biomass. In this work, birch sawdust was extracted using pressurized hot water (PHWE) flow-through systems. The hypothesis of the work was that it is possible to obtain polymeric, water-soluble hemicelluloses from birch sawdust using flow-through PHW extractions at both laboratory and large scale. Different extraction temperatures in the range 140–200 °C were evaluated to see the effect of temperature to the xylan yield. The yields and extracted hemicelluloses were analysed to obtain sugar ratios, the amount of acetyl groups, furfurals and the xylan yields. Higher extraction temperatures increased the xylan yield, but decreased the molar mass of the dissolved xylan. As the extraction temperature increased, more acetic acid was released from the hemicelluloses, thus further decreasing the pH of the extract. There were only trace amounts of furfurals present after the extractions, indicating that the treatment was mild enough not to degrade the sugars further. The sawdust extraction density was increased by packing more sawdust in the laboratory scale extraction vessel. The aim was to obtain extracts with higher concentration than in typical extraction densities. The extraction times and water flow rates were kept constant during these extractions. The higher sawdust packing degree decreased the water use in the extractions and the extracts had higher hemicellulose concentrations than extractions with lower sawdust degrees of packing. The molar masses of the hemicelluloses were similar in higher packing degrees and in the degrees of packing that were used in typical PHWE flow-through extractions. The structure of extracted sawdust was investigated using small angle-(SAXS) and wide angle (WAXS) x-ray scattering. The cell wall topography of birch sawdust and extracted sawdust was compared using x-ray tomography. The results showed that the structure of the cell walls of extracted birch sawdust was preserved but the cell walls were thinner after the extractions. Larger pores were opened inside the fibres and cellulose microfibrils were more tightly packed after the extraction. Acetate buffers were used to control the pH of the extracts during the extractions. The pH control prevented excessive xylan hydrolysis and increased the molar masses of the extracted xylans. The yields of buffered extractions were lower than for plain water extractions at 160–170 °C, but at 180 °C yields were similar to those from plain water and pH buffers. The pH can thus be controlled during extraction with acetate buffer to obtain xylan with higher molar mass than those obtainable using plain water. Birch sawdust was extracted both in the laboratory and pilot scale. The performance of the PHWE flow-through system was evaluated in the laboratory and the pilot scale using vessels with the same shape but different volumes, with the same relative water flow through the sawdust bed, and in the same extraction temperature. Pre-steaming improved the extraction efficiency and the water flow through the sawdust bed. The extracted birch sawdust and the extracted xylan were similar in both laboratory and pilot scale. The PHWE system was successfully scaled up by a factor of 6000 from the laboratory to pilot scale and extractions performed equally well in both scales. The results show that a flow-through system can be further scaled up and used to extract water-soluble xylans from birch sawdust. Extracted xylans can be concentrated, purified, and then used in e.g. films and barriers, or as building blocks for novel material applications.

The role of business model in computer game development organizations

The computer game industry has grown steadily for years, and in revenues it can be compared to the music and film industries. The game industry has been moving to digital distribution. Computer gaming and the concept of business model are discussed among industrial practitioners and the scientific community. The significance of the business model concept has increased in the scientific literature recently, although there is still a lot of discussion going on on the concept. In the thesis, the role of the business model in the computer game industry is studied. Computer game developers, designers, project managers and organization leaders in 11 computer game companies were interviewed. The data was analyzed to identify the important elements of computer game business model, how the business model concept is perceived and how the growth of the organization affects the business model. It was identified that the importance of human capital is crucial to the business. As games are partly a product of creative thinking also innovation and the creative process are highly valued. The same applies to technical skills when performing various activities. Marketing and customer relationships are also considered as key elements in the computer game business model. Financing and partners are important especially for startups, when the organization is dependent on external funding and third party assets. The results of this study provide organizations with improved understanding on how the organization is built and what business model elements are weighted.

Voimalaitosten kattilaputkien sisäpuolisten kerrostumien paksuuden mittaaminen ultraäänimenetelmällä

Höyryvoimalaitoksen käyttöönotossa muodostuu kattilaputkien sisäpinnoille niitä korroosiolta suojaava ohut metallioksidikerros. Tämän kerroksen päälle kasvaa kattilan käytön aikana haitallista kerrostumaa paikallisen korroosion tai kattilavedessä olevien epäpuhtauksien kerääntymisen tai kiteytymisen seurauksena. Kerrostuma haittaa lämmönsiirtoa tulipesästä putkiseinämän läpi kattilaveteen. Putkien lämpötilan nousu suunniteltua korkeammaksi kasvattaa putkivaurioiden ja sisäpuolisen korroosion riskiä. Tästä johtuen paksuksi kasvaneet kerrostumat pyritään poistamaan happokäsittelyllä eli peittauksella ennen vaurioiden syntyä. Perinteisesti kerrostumapaksuus on määritetty kattilasta irrotetuista näyteputkista mikroskoopilla. Työn tavoitteena oli tutkia uudenlaisen ultraäänimittauksen teoriaa ja selvittää sen toimivuus höyrystinputkien kerrostumapaksuusmittauksissa. Lisäksi tavoitteena oli tutkia voimalaitoksen höyrystimen sisäpuolisten kerrostumien muodostumista ja niiden vaikutuksia sekä kattilan peittaustarpeen arviointia. Höyrystimen kerrostumien kasvunopeuteen vaikuttavat eniten voimalaitostyyppi, käytetty vesikemia ja kattilaveteen kulkeutuvien epäpuhtauksien määrä. Kasvunopeus vaihtelee laitosten välillä suuresti ja eroaa myös tulipesän eri kohdissa. Kattilaveden epäpuhtauspitoisuus ja kerrostumapaksuus vaikuttavat molemmat korroosiovaurioiden todennäköisyyteen. Peittauspaksuuden ohjearvoissa tulisi huomioida kattilan käyttöpaine, kattilatyyppi ja riski kattilaveden laadun heikkenemiselle. Putkinäytteistä ja laitoksilla suoritettujen mittauksien perusteella uusi ultraäänitekniikka tuottaa luotettavia tuloksia tavanomaisten kerrostumien mittauksessa. Vain yhdellä laitoksella esiintyi irtonaisen sakan kaltaista kerrostumaa, jota mittaus ei kyennyt havaitsemaan. Mittaustulokset kerrostumista tulipesän eri osissa antavat hyvän perustan peittaustarpeen arviointiin.

Plant adaptation to temperature and photoperiod

Selostus: Kasvien sopeutuminen lämpötilaan ja päivän pituuteen

Sensitivity of temperate grassland species to elevated atmospheric CO2 and the interaction with temperature and water stress

Selostus: Kohonneen hiilidioksidipitoisuuden, lämpötilan ja kuivuuden vaikutus nurmikasveihin

Simulation of spring wheat responses to elevated CO‚́‚ and temperature by using CERES-wheat crop model

Selostus: Kohotettujen CO‚́‚:n ja lämpötilan vaikutukset kevätvehnän fenologiseen kehitykseen ja sadontuottomahdollisuuksiin

Responses of silver birch saplings to low soil temperature

Abstract

Synchronous Digital Hierarchy implementation to a Radio Transmission Node

Kiristyville markkinoille on aina tuotava jotain uutta tarjottavaa ja SDH-kortti on yksi sellainen tuote jonka Nokia Networks julkistaa osaksi uutta Nokia Flexihub Nodea. Tavoitteena on suunnitella VC-12kanavoitu STM-1 kortti yhdistämään ylemmän tason tietoliikenneverkko suuren kapasiteetin radioon. Ennen kuin markkinoilla on valmis tuote, on sen takana valtaisa määrä työtä. Erilaisia dokumentteja on pitänyt tuottaa ja sopimuksia tehdä. Esimerkiksi vaatimusmäärittelyt on oltava selvät, jotta tiedetään mitä tuotteelta halutaan. Tätä ennen on kuitenkin pitänyt ymmärtää miten SDHtoimii ja miten otsikkotavuja käsitellään. Myös erilaiset piirivalinnat aiheuttavat miettimistä, sillä markkinoilla on runsaasti valmiita piirejä SDH signaalinkäsittelyyn. Varma tiedonsiirto on tärkeää puhelinoperaattorille ja siksi joudutaan miettimään varmennuksia ja niiden toteuttamista. Myös synkronointi on tärkeä osa SDH järjestelmää ja sen toteuttaminen hyvin on tärkeää. Hälytykset on otettava huomioon ja mietittävä, miten niiden käsittely saadaan hoidettua järkevästi, ilman että mikään järjestelmän osa ruuhkautuu kohtuuttomasti. Tässä Diplomityössä on tutustuttu SDH-järjestelmään, otsikkotavujen käsittelyyn ja vaatimusmäärittelyihin.

Digital printing delivering value to the value network: CASE: STORA ENSO OYJ

Tutkielman tavoitteena oli tutkia, millaista arvoa digitaalinen painatusmenetelmä tuo yrityksen arvoverkostoon. Teoriaosassa tavoite oli rakentaa digitaalipainatuksen arvoverkostoa tutkien kirjallisuutta liittyen arvoketju- ja arvoverkostoajatteluun. Myös aiemmat tutkimukset ja kirjallisuus liittyen digitaalipainatukseen rakensivat osaltaan teoreettisen viitekehyksen muodostumista. Aiemmat tutkimukset digitaalisen painomenetelmän mahdollisuuksista ovat hyvin tekniikkapainotteisia, siksi tämä tutkimus liittyy enemmän kaupallisiin mahdollisuuksiin. Empiirinen osio tutkimuksesta tehtiin kvalitatiivisena case -tutkimuksena, johon sisältyi yksi alayksikkö. Eli tutkittiin yhtä casea, jossa oli kaksi osapuolta. Tutkielma liittyy kiinteästi Stora Enson ja Valion väliseen digipainatus-projektiin, joka käynnistettiin helmikuussa 2001. Tutkielman teemahaastatteluihin valittiin henkilöt tästä projektiryhmästä. Projektiryhmän mielipiteitä ja havaintoja hyödyntäen pyrittiin löytämään tukea ja eroavaisuuksia teoriaosan muodostamaan viitekehykseen ja informaatioon. Empiirinen osuus tuki teoriaosassa esittämiä väittämiä hyvin, mutta myös muutamia uusia havaintoja esiintyi. Tutkimusongelmaan löydettiin monia vastauksia: digitaalipainatus luo arvoa yrityksen jakeluketjuun vähentämällä varastoja ja nopeuttamalla toimituksia. Jäätelöpakkausten markkinointi on aivan uuden haasteen edessä, koska mahdollisuudet kasvavat digitaalipainatuksen myötä huomattavasti. Kartongin valmistajalle arvo tulee parempien tuotteiden kautta, joista saa myös paremman tuoton. Digitaalipainatuksen arvoverkostossa tulee tapahtumaan muutoksia jatkossa, eri osapuolten roolit saattavat muuttua radikaalisti. Kuka hoitaa painatusta ja miten?

Positron measurements in Mg-doped GaN and development of digital Doppler broadening spectroscopy

In this work parameters of Mg-doped GaN samples were studied using positron annihilation spectroscopy and analyzed. It is shown that gallium vacancies exist in an unintentionally doped sample. Next, the sample with higher concentration of Mg and low growth temperature contains vacancy clusters. In case of low concentration of Mg the growth temperature does not affect the formation of defects. Analog electronics can be replaced by a modern digital device. While promising a high quantity of benefits, the performance of these digitizers requires thorough adjustment. A 14-bit two channel digitizer has been tested in order to achieve better performance than the one of a traditional analog setup, and the adjustment process is described. It has been shown that the digital device is unable to achieve better energy resolution, but it is quite close to the corresponding attribute of the available analog system, which had been used for measurements in Mg-doped GaN.

DIGITAL BUSINESS-TO-BUSINESS MARKETING COMMUNICATIONS IN EMERGING MARKETS – Developing Business Marketing in Russia

The core idea of this Master's Thesis was that five key characteristics – market heterogeneity, sociopolitical governance, chronic shortage of resources, unbranded competition, and inadequate infrastructure – of emerging markets are radically different from the traditional industrialized capitalist society and they will require us to rethink the core assumptions of business-to-business marketing, such as business relationships, marketing communication elements, and digitalization. In this research, Russia is considered to be an emerging market that reflects the aforementioned theoretical characteristics. The research was a qualitative case study and furthermore a collective case study. In the beginning three digital marketing professionals were interviewed to better understand digital B2B marketing. The actual research data was collected through seven structured theme interviews with representatives of the case companies operating in Russia. The selection of case companies included three business consulting companies and four industrial companies. The aim of this qualitative study was to understand and clarify how business marketing exploits digital marketing methods as a part of the chosen business marketing strategy under emerging markets’ special conditions. This objective was divided in three research questions: 1) How the chosen marketing strategy reflects in the business marketing process? 2) How digital marketing communication contributes to business marketing? 3) How are the emerging markets’ characteristics reflected in the business marketing process? The main research findings indicate that digital business-to-business marketing communications can be useful and effective. Moreover, business DMC can be defined and structured in a reasonable way. The company's prevalent marketing paradigm and the chosen marketing strategy reflect in the business marketing process, and in utilizing digital marketing communications. The assumption that emerging markets set an environment with special characteristics for business marketing was supported by the study. However, the business environmental aspects were not considerably disturbing digital B2B marketing, but making it even more reasonable to harness in Russia.

Power cycling lifetime estimation of IGBT power modules based on chip temperature modeling

In this doctoral thesis, methods to estimate the expected power cycling life of power semiconductor modules based on chip temperature modeling are developed. Frequency converters operate under dynamic loads in most electric drives. The varying loads cause thermal expansion and contraction, which stresses the internal boundaries between the material layers in the power module. Eventually, the stress wears out the semiconductor modules. The wear-out cannot be detected by traditional temperature or current measurements inside the frequency converter. Therefore, it is important to develop a method to predict the end of the converter lifetime. The thesis concentrates on power-cycling-related failures of insulated gate bipolar transistors. Two types of power modules are discussed: a direct bonded copper (DBC) sandwich structure with and without a baseplate. Most common failure mechanisms are reviewed, and methods to improve the power cycling lifetime of the power modules are presented. Power cycling curves are determined for a module with a lead-free solder by accelerated power cycling tests. A lifetime model is selected and the parameters are updated based on the power cycling test results. According to the measurements, the factor of improvement in the power cycling lifetime of modern IGBT power modules is greater than 10 during the last decade. Also, it is noticed that a 10 C increase in the chip temperature cycle amplitude decreases the lifetime by 40%. A thermal model for the chip temperature estimation is developed. The model is based on power loss estimation of the chip from the output current of the frequency converter. The model is verified with a purpose-built test equipment, which allows simultaneous measurement and simulation of the chip temperature with an arbitrary load waveform. The measurement system is shown to be convenient for studying the thermal behavior of the chip. It is found that the thermal model has a 5 C accuracy in the temperature estimation. The temperature cycles that the power semiconductor chip has experienced are counted by the rainflow algorithm. The counted cycles are compared with the experimentally verified power cycling curves to estimate the life consumption based on the mission profile of the drive. The methods are validated by the lifetime estimation of a power module in a direct-driven wind turbine. The estimated lifetime of the IGBT power module in a direct-driven wind turbine is 15 000 years, if the turbine is located in south-eastern Finland.