Competitor comparison: variable speed drives in pumping applications

As the world’s energy demand is increasing, a durable solution to control it is to improve the energy efficiency of the processes. It has been estimated that pumping applications have a significant potential for energy savings trough equipment or control system changes. For many pumping application the use of a variable speed drive as a process control element is the most energy efficient solution. The main target of this study is to examine the energy efficiency of a drive system that moves the pump. In a larger scale the purpose of this study is to examine how the different manufacturers’ variable speed drives are functioning as a control device of a pumping process. The idea is to compare the drives from a normal pump user’s point of view. The things that are mattering for the pump user are the efficiency gained in the process and the easiness of the use of the VSD. So some thought is given also on valuating the user-friendliness of the VSDs. The VSDs are compared to each other also on the basis of their life cycle energy costs in different kind of pumping cases. The comparison is made between ACS800 from ABB, VLT AQUA Drive from Danfoss, NX-drive from Vacon and Micromaster 430 from Siemens. The efficiencies are measured in power electronics laboratory in the Lappeenranta University of Technology with a system that consists of a variable speed drive, an induction motor with dc-machine, two power analyzers and a torque transducer. The efficiencies are measured as a function of a load at different frequencies. According to measurement results the differences between the measured system efficiencies on the actual working area of pumping are on average few percent units. When examining efficiencies at the whole range of different loads and frequencies, the differences get bigger. At low frequencies and loads the differences between the most efficient and the least efficient systems are at the most about ten percent units. At the most of the tested points ABB’s drive seem to have slightly better efficiencies than the other drives.

Advanced chemometric methods: Applicability on industrial data

Recent years have produced great advances in the instrumentation technology. The amount of available data has been increasing due to the simplicity, speed and accuracy of current spectroscopic instruments. Most of these data are, however, meaningless without a proper analysis. This has been one of the reasons for the overgrowing success of multivariate handling of such data. Industrial data is commonly not designed data; in other words, there is no exact experimental design, but rather the data have been collected as a routine procedure during an industrial process. This makes certain demands on the multivariate modeling, as the selection of samples and variables can have an enormous effect. Common approaches in the modeling of industrial data are PCA (principal component analysis) and PLS (projection to latent structures or partial least squares) but there are also other methods that should be considered. The more advanced methods include multi block modeling and nonlinear modeling. In this thesis it is shown that the results of data analysis vary according to the modeling approach used, thus making the selection of the modeling approach dependent on the purpose of the model. If the model is intended to provide accurate predictions, the approach should be different than in the case where the purpose of modeling is mostly to obtain information about the variables and the process. For industrial applicability it is essential that the methods are robust and sufficiently simple to apply. In this way the methods and the results can be compared and an approach selected that is suitable for the intended purpose. Differences in data analysis methods are compared with data from different fields of industry in this thesis. In the first two papers, the multi block method is considered for data originating from the oil and fertilizer industries. The results are compared to those from PLS and priority PLS. The third paper considers applicability of multivariate models to process control for a reactive crystallization process. In the fourth paper, nonlinear modeling is examined with a data set from the oil industry. The response has a nonlinear relation to the descriptor matrix, and the results are compared between linear modeling, polynomial PLS and nonlinear modeling using nonlinear score vectors.

Nosturin kuormauselimen liitynnän suunnittelu

Paperiteollisuuden prosessituotteista paperia varastoidaan erikokoisina rullina esim. pystyrullavarastoihin. Tämän diplomityön tavoitteena oli kehittää Konecranesin prosessinosturille liityntä paperirullia käsittelevän kuormauselimen ja nosturin välille. Tavoitteena oli löytää kiinnitysmenetelmä, joka mahdollistaa nosturien joustavan käytön mahdollisimman pienin muutoksin itse nosturin standardoituun rakenteeseen. Pääasiallisena syventymisen kohteena oli alipaineella paperirullia nostettavan kuormauselimen liityntä. Liitynnän on kyettävä joustamaan ja vaimentamaan paperirullia nostavaan kuormauselimeen nosturin liikkeelle lähdöstä ja pysähtymisestä syntyvät herätteet ja voimat. Nosturin liikenopeus on kyettävä pitämään mahdollisimman suurena lyhyen rullienkäsittelyajan saavuttamiseksi. Liitynnältä vaaditaan kykyä ottaa kuormauselin vastaan mahdollisimman suurella nostonopeudella. Lisäksi kuorman ja kuormauselimen oskillaatio on vaimennettava mahdollisimman nopeasti samalla rajoittaen heilunnasta aiheutuvaa maksimi siirtymää. Liitynnän suunnittelu pohjautuu nosturin, kuormauselimen ja paperirullan muodostaman systeemin teoreettiseen tarkasteluun. Systeemistä laadittiin dynaaminen malli, jonka avulla tutkittiin oskillaation ja syntyvien kiihtyvyyksien suuruutta. Näiden teoriaan perustuvien tuloksien pohjalta suunniteltiin vaimennukseen tarvittavat vaimennuselementit ja liitynnän rakenne. Suunnittelutyön tuloksena saatiin liitynnälle alustava rakenne, joka mahdollistaa käytettävien vaimennuselementtien vaihtamisen ja siten tehokkaan heilunnan vaimmennuksen. Suunnittelutyön lähtökohtana oleva teoreettinen tarkastelu vaatii tuekseen esim. prototyypin kokeellisten tulosten saamiseksi ennen lopullisen tuotteen valmistamista. Suunnitteluprosessissa noudatettiin järjestelmällisen tuotesuunnittelun vaiheita ja menetelmiä.

Hitsauksen laadunhallinta offshore-teollisuuden alihankintakonepajassa

Diplomityön tavoitteena oli kuvata hitsauksen laadunhallintaa sekä hitsauksen laadunhallintajärjestelmän rakentamista offshore-teollisuuden konepajaan standardin ISO 3834-2 mukaisesti. Diplomityö koostuu teoriaosasta sekä käytännön osasta. Teoriaosa käsittelee laadunhallintaa yleisesti, minkä jälkeen se tarkentuu käsittelemään hitsauksen laadunhallintaa. Esimerkkinä on esitetty standardin NORSOK M-101 mukaisia laatuvaatimuksia. Laadunhallintaan liittyy oleellisesti myös hitsausliitoksen NDT-tarkastaminen, josta on käsitelty silmämääräinen tarkastus ja ultraäänitarkastus. Teoriaosan lopussa on käsitelty hitsauksen työturvallisuutta sekä hitsauksen laadunvalvontaa online-seurantajärjestelmällä. Käytännön osassa kerrotaan hitsauksen laatujärjestelmän rakentamisesta Meteco Oy:n Kuhmoisten tehtaalla. Yrityksen nykytilanne kartoitettiin, minkä jälkeen ryhdyttiin rakentamaan hitsauksen laadunhallintajärjestelmää. Tuloksena syntyi hitsauksen laatukäsikirja, joka pohjautuu standardiin ISO 3834-2. Käytännön osuudessa on kerrottu myös online-seurantajärjestelmän soveltuvuudesta alihankintakonepajan käyttöön. Hitsauksen laatujärjestelmän rakentamiseen kuului henkilöstön koulutustilaisuudet, joissa informoitiin edellä mainitun laatukäsikirjaan kuuluvista asioista. Tästä syntyi yritykseen myös koulutusohjelmasuunnitelma, joka antaa valmiudet yrityksen henkilökunnalle kehittyä työssään ja näin tehostaa toimintaa.

Delay reduction in courts of justice – possibilities and challenges of process improvement in professional public organizations

Delays in the justice system have been undermining the functioning and performance of the court system all over the world for decades. Despite the widespread concern about delays, the solutions have not kept up with the growth of the problem. The delay problem existing in the justice courts processes is a good example of the growing need and pressure in professional public organizations to start improving their business process performance.This study analyses the possibilities and challenges of process improvement in professional public organizations. The study is based on experiences gained in two longitudinal action research improvement projects conducted in two separate Finnish law instances; in the Helsinki Court of Appeal and in the Insurance Court. The thesis has two objectives. First objective is to study what kinds of factors in court system operations cause delays and unmanageable backlogs and how to reduce and prevent delays. Based on the lessons learned from the case projects the objective is to give new insights on the critical factors of process improvement conducted in professional public organizations. Four main areas and factors behind the delay problem is identified: 1) goal setting and performance measurement practices, 2) the process control system, 3) production and capacity planning procedures, and 4) process roles and responsibilities. The appropriate improvement solutions include tools to enhance project planning and scheduling and monitoring the agreed time-frames for different phases of the handling process and pending inventory. The study introduces the identified critical factors in different phases of process improvement work carried out in professional public organizations, the ways the critical factors can be incorporated to the different stages of the projects, and discusses the role of external facilitator in assisting process improvement work and in enhancing ownership towards the solutions and improvement. The study highlights the need to concentrate on the critical factors aiming to get the employees to challenge their existing ways of conducting work, analyze their own processes, and create procedures for diffusing the process improvement culture instead of merely concentrating of finding tools, techniques, and solutions appropriate for applications from the manufacturing sector

Itä-Savon sairaanhoitopiiri Ky:n Savonlinnan keskussairaalan paikannustoiminnan kehittäminen

Terveydenhuollon ja siihen liittyvien palvelujen kustannusten jatkuva kohoaminen ja kuntien paheneva taloustilanne sekä terveydenhuollon pienenevät henkilöstöresurssit ovat lisänneet painetta toimintojen kustannustehokkaaseen toteuttamiseen. Edellä mainitusta johtuen, terveydenhuollon toimijoita kehotetaan etsimään uusia ratkaisuja, joilla voidaan taata jatkossa riittävä asiakaspalvelutaso, kustannustehokkuus ja – palvelujen turvallisuus. Tämän työn tavoitteena oli vastata kysymyksiin tunnistus- ja paikannustoiminnan hyödyntämisen mahdollisuuksista Itä-Savon sairaanhoitopiirin Savonlinnan keskussairaalassa. Tarkoituksena oli selvittää, millaisia paikannus ja tunnistusteknologiaan liittyviä tavoitteita ja vaatimuksia terveydenhuollon toimialalla ja erityisesti Itä-Savon sairaanhoitopiirissä on ja millä tavalla RFID ja WLAN – teknologioilla saadaan kehitettyä asetettuihin tavoitteisiin ja hyötyodotuksiin vastaavat ratkaisut. Työssä pyrittiin selvittämään myös millaisia rahallisia säästöjä tunnistus- ja paikannusteknologioilla voidaan saada aikaan. Työn yhteydessä kartoitettiin tarpeita ja vaatimuksia tunnistus- ja paikannusteknologian hyödyntämiseen. Tarpeet ja vaatimukset testattiin tunnistus- ja paikannuspilotissa. Lisäksi perehdyttiin kirjallisuuteen ja aiempiin tutkimuksiin tunnistus- ja paikannusteknologioista. Suunnitelman perusteella näyttää siltä, että hyödyntämällä tunnistus- ja paikannusteknologioita voitaisiin tehostaa Savonlinnan keskussairaalan toimintaa. Suunnitelman pilottivaiheen tuloksien perusteella toiminnan tehostaminen tarkoittaisi kustannussäästöjä, parantaisi potilasturvallisuutta sekä hoitotyön laatua. Tunnistus- ja paikannusteknologian käyttökohteita sairaalassa voisivat olla esimerkiksi reaaliaikaiseen prosessien ohjaaminen, kulunvalvonnan ja -ohjauksen automatisointi, potilaan automaattinen tunnistaminen, sekä sairaalan tutkimuslaitteiden seuranta.

Katsastuksen teknisen laadun mittaaminen ja johtaminen

Suorituskyvyn mittaamisella on monia myönteisiä vaikutuksia koko organisaation toimintaan. Mittaamisen avulla toimintaa voidaan johtaa haluttuun suuntaan. Tutkimuksen tavoitteena oli tutkia, minkälainen suorituskykymittaristo tarvitaan katsastusyrityksen ylimmän johdon käyttöön, jotta katsastuksen teknisen laadun johtaminen mahdollistuisi. Tutkimuksen tarkoituksena oli rakentaa katsastuksen teknisen laadun suorituskykymittaristo ylimmälle johdolle. Katsastuksen tekninen laatu on keskeinen kysymys katsastusyritysten olemassaololle. Tekninen laatu on koko katsastustoiminnan perusta, jonka päälle liiketoiminta voidaan rakentaa. Ilman tätä perustaa ei ole jatkuvuutta liiketoiminnalle. Teknisen laadun mittaaminen ei kuitenkaan ole tällä hetkellä järjestelmällistä, eikä käytettävissä ole ollut tehtävään soveltuvaa mittaristoa. Tutkimuksessa käytettiin A-Katsastus Oy:n vuosien 2008–2011 aikana syntyneitä katsastustilastoja. Tilastollista prosessin valvonta-menetelmää (SPC) soveltamalla määritettiin toimipaikka- ja katsastajakohtaiset valvontarajat hylkäysprosenteille ja vikojen määrille. Valvontarajojen avulla rakennettiin katsastuksen teknisen laadun suorituskykymittaristo toimiala-, yritys-, toimipaikka- ja katsastajatasoille. Mittariston avulla voidaan asettaa tekniselle laadulle tavoitteet, seurata tavoitteiden toteumaa ja käynnistää tarvittaessa korjaavat toimenpiteet.

Liquid transportation and distribution during (re)wetting : impact on coated papers in printing

In many industrial applications, such as the printing and coatings industry, wetting of porous materials by liquids includes not only imbibition and permeation into the bulk but also surface spreading and evaporation. By understanding these phenomena, valuable information can be obtained for improved process control, runnability and printability, in which liquid penetration and subsequent drying play important quality and economic roles. Knowledge of the position of the wetting front and the distribution/degree of pore filling within the structure is crucial in describing the transport phenomena involved. Although exemplifying paper as a porous medium in this work, the generalisation to dynamic liquid transfer onto a surface, including permeation and imbibition into porous media, is of importance to many industrial and naturally occurring environmental processes. This thesis explains the phenomena in the field of heatset web offset printing but the content and the analyses are applicable in many other printing methods and also other technologies where water/moisture monitoring is crucial in order to have a stable process and achieve high quality end products. The use of near-infrared technology to study the water and moisture response of porous pigmented structures is presented. The use of sensitive surface chemical and structural analysis, as well as the internal structure investigation of a porous structure, to inspect liquid wetting and distribution, complements the information obtained by spectroscopic techniques. Strong emphasis has been put on the scale of measurement, to filter irrelevant information and to understand the relationship between interactions involved. The near-infrared spectroscopic technique, presented here, samples directly the changes in signal absorbance and its variation in the process at multiple locations in a print production line. The in-line non-contact measurements are facilitated by using several diffuse reflectance probes, giving the absolute water/moisture content from a defined position in the dynamic process in real-time. The nearinfrared measurement data illustrate the changes in moisture content as the paper is passing through the printing nips and dryer, respectively, and the analysis of the mechanisms involved highlight the roles of the contacting surfaces and the relative liquid carrier properties of both non-image and printed image areas. The thesis includes laboratory studies on wetting of porous media in the form of coated paper and compressed pigment tablets by mono-, dual-, and multi-component liquids, and paper water/moisture content analysis in both offline and online conditions, thus also enabling direct sampling of temporal water/moisture profiles from multiple locations. One main focus in this thesis was to establish a measurement system which is able to monitor rapid changes in moisture content of paper. The study suggests that near-infrared diffuse reflectance spectroscopy can be used as a moisture sensitive system and to provide accurate online qualitative indicators, but, also, when accurately calibrated, can provide quantification of water/moisture levels, its distribution and dynamic liquid transfer. Due to the high sensitivity, samples can be measured with excellent reproducibility and good signal to noise ratio. Another focus of this thesis was on the evolution of the moisture content, i.e. changes in moisture content referred to (re)wetting, and liquid distribution during printing of coated paper. The study confirmed different wetting phases together with the factors affecting each phase both for a single droplet and a liquid film applied on a porous substrate. For a single droplet, initial capillary driven imbibition is followed by equilibrium pore filling and liquid retreat by evaporation. In the case of a liquid film applied on paper, the controlling factors defining the transportation were concluded to be the applied liquid volume in relation to surface roughness, capillarity and permeability of the coating giving the liquid uptake capacity. The printing trials confirmed moisture gradients in the printed sheet depending on process parameters such as speed, fountain solution dosage and drying conditions as well as the printed layout itself. Uneven moisture distribution in the printed sheet was identified to be one of the sources for waving appearance and the magnitude of waving was influenced by the drying conditions.

Characterization of fiber and vessel elements in pulp suspension images

The thesis is related to the topic of image-based characterization of fibers in pulp suspension during the papermaking process. Papermaking industry is focusing on process control optimization and automatization, which makes it possible to manufacture highquality products in a resource-efficient way. Being a part of the process control, pulp suspension analysis allows to predict and modify properties of the end product. This work is a part of the tree species identification task and focuses on analysis of fiber parameters in the pulp suspension at the wet stage of paper production. The existing machine vision methods for pulp characterization were investigated, and a method exploiting direction sensitive filtering, non-maximum suppression, hysteresis thresholding, tensor voting, and curve extraction from tensor maps was developed. Application of the method to the microscopic grayscale pulp images made it possible to detect curves corresponding to fibers in the pulp image and to compute their morphological characteristics. Performance of the method was evaluated based on the manually produced ground truth data. An accuracy of fiber characteristics estimation, including length, width, and curvature, for the acacia pulp images was found to be 84, 85, and 60% correspondingly.

Determination of collector chemicals from flotation process waters using capillary electrophoresis

Vaahdotusprosessia käytetään yleisesti erottamaan arvokkaita mineraaleja malmeista. Toimiakseen tehokkaasti prosessi tarvitsee kokoojakemikaaleja, joiden tehtävänä on sitoa halutut mineraalit ilmakupliin. Jotta näiden kemikaalien käyttäytymistä prosessissa voitaisiin ymmärtää paremmin ja prosessin ohjausta tehostaa, pitää kokoojia pystyä analysoimaan prosessivesistä. Työn kirjallisuusosassa on koottu ja vertailtu erilaisia kirjallisuudesta löytyneitä analyysimenetelmiä kokoojakemikaaleille. Kokeellisessaosassa on kehitetty kaksi kapillaarielektroforeesimenetelmää näiden kemikaalien tutkimiseen. Menetelmien toteamisrajat tutkituille kemikaaleille olivat seuraavanlaiset: natrium diiosobutylditiofosfaattille (DTP) 2,7 mg/L puhtaassa vedessä ja 6,7 mg/L prosessivedessä; natrium diisobutyldithiofosfinaatille (DTPI) vastaavasti 4,5 mg/L ja 6,7 mg/L; etyyli ksantaatille 0,025 mg/L ja 0,16 mg/L; ja isobutyyli ksantaatille 0,41 mg/L ja 0,62 mg/L. Näitä menetelmiä voidaan tulevaisuudessa kehittää kokoojien hajoamistuotteiden analysointia varten sekä prosessien on-line mittauksiin.

Concentration of hydrogen peroxide and improving its energy efficiency

Distillation is a unit operation of process industry, which is used to separate a liquid mixture into two or more products and to concentrate liquid mixtures. A drawback of the distillation is its high energy consumption. An increase in energy and raw material prices has led to seeking ways to improve the energy efficiency of distillation. In this Master's Thesis, these ways are studied in connection with the concentration of hydrogen peroxide at the Solvay Voikkaa Plant. The aim of this thesis is to improve the energy efficiency of the concentration of the Voikkaa Plant. The work includes a review of hydrogen peroxide and its manufacturing. In addition, the fundamentals of distillation and its energy efficiency are reviewed. An energy analysis of the concentration unit of Solvay Voikkaa Plant is presented in the process development study part. It consists of the current and past information of energy and utility consumptions, balances, and costs. After that, the potential ways to improve the energy efficiency of the distillation unit at the factory are considered and their feasibility is evaluated technically and economically. Finally, proposals to improve the energy efficiency are suggested. Advanced process control, heat integration and energy efficient equipment are the most potential ways to carry out the energy efficient improvements of the concentration at the Solvay Voikkaa factory. Optimization of the reflux flow and the temperatures of the overhead condensers can offer immediate savings in the energy and utility costs without investments. Replacing the steam ejector system with a vacuum pump would result in savings of tens of thousands of euros per year. The heat pump solutions, such as utilizing a mechanical vapor recompression or thermal vapor recompression, are not feasible due to the high investment costs and long pay back times.

Project Charter, Scope, and Time Management In the Movie Industry

This thesis explores how the project charter development, project scope management, and project time management are executed in a Finnish movie production. The deviations and analogies between a case movie production and best practices suggested in PMBOK are presented. Empirical material from the case is gathered with two semi-structured interviews with a producer and a line producer. The interview data is categorized according to PMBOK knowledge areas. The analysis is complemented with movie industry specific norms found in popular movie production guides. The described and observed methods are linked together and the relationship between them is discussed. The project charter development, which is referred as a green light process in the movie industry, is mostly analogous between all areas. The deviations are in the level of formality. The green lighting in the case movie was accomplished without bureaucratic reports described in movie production guides. The empirical material shows that project management conventions and movie industry employ similar methods especially in scope management. Project management practices introduce a work breakdown structure (WBS) method, and movie production accomplishes the same task by developing a shooting script. Time management of the case movie deviates on most parts from the methods suggested in PMBOK. The major deviation is resource management. PMBOK suggests creating a resource breakdown structure. The case movie production accomplished this through budgeting process. Furthermore the popular movie production guides also disregard resource management as sovereign process. However the activity listing is quite analogous between the case movie and PMBOK. The final key observation is that although there is a broad set of effective and detailed movie industry specific methods, a comprehensive methodology that would cover the whole production process, such as Prince2 or Scrum, seems to be missing from the movie industry.

Project charter, scope, and time management in the movie industry

This thesis explores how the project charter development, project scope management, and project time management are executed in a Finnish movie production. The deviations and analogies between a case movie production and best practices suggested in PMBOK are presented. Empirical material from the case is gathered with two semi-structured interviews with a producer and a line producer. The interview data is categorized according to PMBOK knowledge areas. The analysis is complemented with movie industry specific norms found in popular movie production guides. The described and observed methods are linked together and the relationship between them is discussed. The project charter development, which is referred as a green light process in the movie industry, is mostly analogous between all areas. The deviations are in the level of formality. The green lighting in the case movie was accomplished without bureaucratic reports described in movie production guides. The empirical material shows that project management conventions and movie industry employ similar methods especially in scope management. Project management practices introduce a work breakdown structure (WBS) method, and movie production accomplishes the same task by developing a shooting script. Time management of the case movie deviates on most parts from the methods suggested in PMBOK. The major deviation is resource management. PMBOK suggests creating a resource breakdown structure. The case movie production accomplished this through budgeting process. Furthermore the popular movie production guides also disregard resource management as sovereign process. However the activity listing is quite analogous between the case movie and PMBOK. The final key observation is that although there is a broad set of effective and detailed movie industry specific methods, a comprehensive methodology that would cover the whole production process, such as Prince2 or Scrum, seems to be missing from the movie industry.

Specification of a smart meter/actuator description mechanism & development of a mobile application

Home Automation holds the potential of realizing cost savings for end users while reducing the carbon footprint of domestic energy consumption. Yet, adoption is still very low. High cost of vendor-supplied home automation systems is a major prohibiting factor. Open source systems such as FHEM, Domoticz, OpenHAB etc. are a cheaper alternative and can drive the adoption of home automation. Moreover, they have the advantage of not being limited to a single vendor or communication technology which gives end users flexibility in the choice of devices to include in their installation. However, interaction with devices having diverse communication technologies can be inconvenient for users thus limiting the utility they derive from it. For application developers, creating applications which interact with the several technologies in the home automation systems is not a consistent process. Hence, there is the need for a common description mechanism that makes interaction smooth for end users and which enables application developers to make home automation applications in a consistent and uniform way. This thesis proposes such a description mechanism within the context of an open source home automation system – FHEM, together with a system concept for its application. A mobile application was developed as a proof of concept of the proposed description mechanism and the results of the implementation are reflected upon.

High speed release -mittausmenetelmän käyttäminen tarralaminaattiprosessin ohjaukses

Työn tavoitteena oli tutkia HSR(High Speed Release)-mittausmenetelmän käyttämistä tarralaminaattiprosessin ohjauksessa UPM Raflatacissa. Nykyisin käytössä olevaan LSR(Low Speed Release)-menetelmään verrattuna HSR-menetelmä kuvaa paremmin tarralaminaatin jatkojalostuksessa sekä etiketöinnissä tapahtuvaa irrotustyötä. Lisäksi työssä tutkittiin irrotusnopeuden vaikutusta HSR-arvoon. Työn kirjallisuusosassa perehdyttiin tarralaminaatin rakenteeseensekä valmistusprosessiin. Koska silikonin valinnalla on merkittävä vaikutus tarralaminaatin releasearvoon, kirjallisessa osassa syvennytään tarkastelemaan tarralaminaatin valmistuksessa käytettyjä silikoneja sekänäiden rakennetta. Kirjallisuusosassa on myös käsitelty muita releasetasoon vaikuttavia tekijöitä. Työn kokeellisessa osassa oli tarkoituksena tutkia HSR-mittausmenetelmän käytettävyyttä tarralaminaatin prosessinohjauksessa. Tätä tutkittiin selvittämällä nykyisin käytössä olevan LSR-menetelmän sekä HSR-menetelmän välistä korreloituvuutta. Mikäli näidenvälillä olisi korreloituvuutta, voitaisiin prosessinohjauksessa ajatella siirtyvän HSR-mittaukseen. Korrelaatiota näiden kahden menetelmän välille ei kuitenkaan löydetty. Työssä tutkittiin myös irrotusnopeuden vaikutusta tuotteen HSR-arvoon. Testeihin valittiin useita eri tuotteita useilta tuotantolaitoksilta. Kaikilla näillä tuotteilla releasearvo kasvoi irrotusnopeutta lisättäessä. Lisäksi työssä määritettiin uudet HSR-spesifikaatiot tietyille tuotteille. Kaikille UPM Raflatacin tuotteille on määritetty LSRspesifikaatiot, HSR-spesifikaatiot on asetettu vain tietyille tuotteille.