Kipsin kiteytymiseen vaikuttavat tekijät ammoniumsulfaattikiteyttämön lämmönvaihtimissa

Työssä pyrittiin selvittämään syitä kipsin saostumiseen ammoniumsulfaattikiteyttämön putkilämmönvaihtimien pinnalle ja miten epätoivottua saostumista voitaisiin estää. Lämmönvaihtimissa virtaa ammoniumsulfaattia, jossa on epäpuhtautena kalsiumia, joka saostuu pinnoille kalsiumsulfaattina. Kirjallisuusosassa tarkasteltiin kiteytymisen mekanismia ja kipsin kiteytymiseen vaikuttavia tekijöitä. Saostumien estoaineita ja niiden vaikutusta kipsin kiteytymiseen sekä kipsin liukoisuutta ammoniumsulfaattiliuoksessa käsiteltiin myös kirjallisuusosassa. Kipsin kiteytymiseen vaikuttavia tekijöitä selvitettiin laboratoriokokeilla, joissa pyrittiin simuloimaan lämmönvaihdinta lämpövastuksella. Laboratoriokokeissa kokeiltiin erilaisia saostuman estoaineita ja pyrittiin löytämään prosessiin mahdollisimman tehokas kipsin kiteytymisen estoaine. Lämmönvaihtimien toiminnan tehokkuutta eli muodostuneen saostuman vaikutusta lämmönsiirtymiseen tutkittiin veden luovuttaman lämpövirran avulla. Lämmönvaihtimien tukkeutumista selvitettiin putkien vaihdon tarpeen perusteella. Kalsiumpitoisuuden vaihteluja prosessivirroissa selvitettiin kalsiumtaseen avulla. Saostumiseen vaikuttavien tekijöiden lisäksi selvitettiin mistä ja kuinka paljon kalsiumia kulkeutuu prosessiin ja poistuu sieltä. Työn tarkoituksena oli löytää ratkaisu, jolla epätoivottua saostumista lämmönvaihdin-ten pinnoille pystyttäisiin vähentämään joko kemiallisesti tai muuttamalla prosessi-muuttujia. Kalsiumia havaittiin olevan eniten pelkistämön sisäisissä ammoniumsul-faattiliuoskierroissa. Kalsiumtaseen perusteella kalsiumia poistuu pelkistämöltä eniten kipsinä ammoniumsulfaattituotteen mukana. Laboratoriokokeissa havaittiin polykar-boksylaattien estävän kipsin kasvua parhaiten, joskin estoaineen oikealla annostuksel-la havaittiin olevan suuri vaikutus. Lämmönvaihtimien saostuman havaittiin olevan kipsin ja glauberiitin seos. Vaippapuolen luovuttamien lämpövirran arvojen perusteel-la pystyttiin seuraamaan putkien tukkeutumista.

Nuclear magnetic resonance investigation of structure and dynamics of some electrolyte solutions

Electrolyte solutions are of importance in a wide range of scientific contexts and as such have attracted considerable theoretical and experimental effort over many years. Nuclear Magnetic resonance provides a precise and versatile tool for investigation of electrolyte solutions, both in water and in organic solvents. Many structural and dynamic properties can be obtained through NMR experiments. The solution of aluminum chloride in water was studied. Different concentrations were taken for investigation. Independence of maximum line shift from concentration and acidity was shown. Six-coordinated structure of solvation shell was confirmed by experiments on 'H and 27A1 nuclei. Diffusion coefficients were studied. The solution of nickel chloride in methanol was studied. Lines, corresponding to coordinated and bulk methanol were found. Four-, five- and six-coordinated structures were found in different temperatures. The line for coordinated -OD group of deuterated methanol was observed on 2H spectrum for the first time. Partial deuteration of CH3 group was detected. Inability to observe coordinated -OH group was explained.

Thermal-Hydraulic Studies on the Safety Of VVER-440 Type Nuclear Power Plants

This thesis includes several thermal hydraulic analyses related to the Loviisa WER 440 nuclear power plant units. The work consists of experimental studies, analysis of the experiments, analysis of some plant transits and development of a calculational model for calculation of boric acid concentrations in the reactor. In the first part of the thesis, in the case of won of boric acid solution behaviour during long term cooling period of LOCAs, experiments were performed in scaled down test facilities. The experimental data together with the results of RELAPS/MOD3 simulations were used to develop a model for calculations of boric acid concentrations in the reactor during LOCAs. The results of calculations showed that margins to critical concentrations that would lead to boric acid crystallization were large, both in the reactor core and in the lower plenum. This was mainly caused by the fact that water in the primary cooling circuit includes borax (Na)BsO,.IOHZO), which enters the reactor when ECC water is taken from the sump and greatly increases boric acid solubility in water. In the second part, in the case of simulation of horizontal steam generators, experiments were performed with PACTEL integral test loop to simulate loss of feedwater transients. The PACTEL experiments, as well as earlier REWET III natural circulation tests, were analyzed with RELAPS/MOD3 Version Sm5 code. The analysis showed that the code was capable of simulating the main events during the experiments. However, in the case of loss of secondary side feedwater the code was not completely capable to simulate steam superheating in the secondary side of the steam generators. The third part of the work consists of simulations of Loviisa VVER reactor pump trip transients with RELAPSlMODI Eur, RELAPS/MOD3 and CATHARE codes. All three codes were capable to simulate the two selected pump trip transients and no significant differences were found between the results of different codes. Comparison of the calculated results with the data measured in the Loviisa plant also showed good agreement.

Rigid Rod Polymer Fillers in Acrylic Denture and Dental Adhesive Resin Systems

Polymeric materials have been used in dental applications for decades. Adhesion of polymeric materials to each other and to the tooth substrate is essential to their successful use. The aim of this series of studies was two-folded. First, to improve adhesion of poly(paraphenylene) based rigid rod polymer (RRP) to other dental polymers, and secondly, to evaluate the usability of a new dentin primer system based on RRP fillers. Poly(paraphenylene) based RRP would be a tempting material for dental applications because of its good mechanical properties. To be used in dental applications, reliable adhesion between RRP and other dental polymers is required. In this series of studies, the adhesion of RRP to denture base polymer and the mechanical properties of RRP-denture base polymer-material combination were evaluated. Also adhesion of BisGMA-TEGDMA-resin to RRP was determined. Different surface treatments were tested to improve the adhesion of BisGMA-TEGDMA-resin to RRP. Results were based on three-point bending testing, Vickers surface hardness test and scanning electron microscope analysis (SEM), which showed that no reliable adhesion between RRP and denture base polymer was formed. Addition of RRP filler to denture base polymer increased surface hardness and flexural modulus but flexural strength decreased. Results from the shear bond strength test and SEM revealed that adhesion between resin and RRP was possible to improve by surface treatment with dichloromethane (DCM) based primer and a new kind of adhesive surface can be designed. The current dentin bonding agents have good immediate bond strength, but in long term the bond strength may decrease due to the detrimental effect of water and perhaps by matrix metalloproteinases. This leads to problems in longevity of restorations. Current bonding agents use organic monomers. In this series of studies, RRP filled dentin primer was tested in order to decrease the water sorption of the monomer system of the primers. The properties of new dentin primer system were evaluated in vitro by comparing it to commercial etch and rinse adhesive system. The results from the contact angle measurements and SEM showed that experimental primer with RRP reinforcement provided similar resin infiltration to dentin collagen and formed the resin-dentin interface as the control primer. Microtensile bond strength test and SEM revealed that in short term water storing, RRP increased bond strength and primer with BMEP-monomer (bis[2-(methacryloyloxy)-ethyl]phosphate) and high solvent concentration provided comparable bonding properties to the commercial control primers. In long term water storing, the high solvent-monomer concentration of the experimental primers decreased bond strength. However, in low solvent-monomer concentration groups, the long-term water storing did not decrease the bond strength despite the existence of hydrophilic monomers which were used in the system. These studies demonstrated that new dentin primer system reached the mechanical properties of current traditional etch and rinse adhesive system in short time water storing. Improved properties can be achieved by further modifications of the monomer system. Studies of the adhesion of RRP to other polymers suggest that adhesion between RRP and other dental polymers is possible to obtain by certain surface treatments.

Polymer surface modification by atomic layer deposition

Current industrial atomic layer deposition (ALD) processes are almost wholly confined to glass or silicon substrates. For many industrial applications, deposition on polymer substrates will be necessary. Current deposition processes are also typically carried out at temperatures which are too high for polymers. If deposition temperatures in ALD can be reduced to the level applicable for polymers, it will open new interesting areas and applications for polymeric materials. The properties of polymers can be improved for example by coatings with functional and protective properties. Although the ALD has shown its capability to operate at low temperatures suitable for polymer substrates, there are other issues related to process efficiency and characteristics of different polymers where new knowledge will assist in developing industrially conceivable ALD processes. Lower deposition temperature in ALD generally means longer process times to facilitate the self limiting film growth mode characteristic to ALD. To improve process efficiency more reactive precursors are introduced into the process. For example in ALD oxide processes these can be more reactive oxidizers, such as ozone and oxygen radicals, to substitute the more conventionally used water. Although replacing water in the low temperature ALD with ozone or plasma generated oxygen radicals will enable the process times to be shortened, they may have unwanted effects both on the film growth and structure, and in some cases can form detrimental process conditions for the polymer substrate. Plasma assistance is a very promising approach to improve the process efficiency. The actual design and placement of the plasma source will have an effect on film growth characteristics and film structure that may retard the process efficiency development. Due to the fact that the lifetime of the radicals is limited, it requires the placement of the plasma source near to the film growth region. Conversely this subjects the substrate to exposure byother plasma species and electromagnetic radiation which sets requirements for plasma conditions optimization. In this thesis ALD has been used to modify, activate and functionalize the polymer surfaces for further improvement of polymer performance subject to application. The issues in ALD on polymers, both in thermal and plasma-assisted ALD will be further discussed.

Understanding the in vitro dissolution rate of glasses with respect to future clinical applications

Glass is a unique material with a long history. Several glass products are used daily in our everyday life, often unnoticed. Glass can be found not only in obvious applications such as tableware, windows, and light bulbs, but also in tennis rackets, windmill turbine blades, optical devices, and medical implants. The glasses used at present as implants are inorganic silica-based melt-derived compositions mainly for hard-tissue repair as bone graft substitute in dentistry and orthopedics. The degree of glass reactivity desired varies according to implantation situation and it is vital that the ion release from any glasses used in medical applications is controlled. Understanding the in vitro dissolution rate of glasses provides a first approximation of their behavior in vivo. Specific studies concerning dissolution properties of bioactive glasses have been relatively scarce and mostly concentrated to static condition studies. The motivation behind this work was to develop a simple and accurate method for quantifying the in vitro dissolution rate of highly different types of glass compositions with interest for future clinical applications. By combining information from various experimental conditions, a better knowledge of glass dissolution and the suitability of different glasses for different medical applications can be obtained. Thus, two traditional and one novel approach were utilized in this thesis to study glass dissolution. The chemical durability of silicate glasses was tested in water and TRIS-buffered solution at static and dynamic conditions. The traditional in vitro testing with a TRISbuffered solution under static conditions works well with bioactive or with readily dissolving glasses, and it is easy to follow the ion dissolution reactions. However, in the buffered solution no marked differences between the more durable glasses were observed. The hydrolytic resistance of the glasses was studied using the standard procedure ISO 719. The relative scale given by the standard failed to provide any relevant information when bioactive glasses were studied. However, the clear differences in the hydrolytic resistance values imply that the method could be used as a rapid test to get an overall idea of the biodegradability of glasses. The standard method combined with the ion concentration and pH measurements gives a better estimate of the hydrolytic resistance because of the high silicon amount released from a glass. A sensitive on-line analysis method utilizing inductively coupled plasma optical emission spectrometer and a flow-through micro-volume pH electrode was developed to study the initial dissolution of biocompatible glasses. This approach was found suitable for compositions within a large range of chemical durability. With this approach, the initial dissolution of all ions could be measured simultaneously and quantitatively, which gave a good overall idea of the initial dissolution rates for the individual ions and the dissolution mechanism. These types of results with glass dissolution were presented for the first time during the course of writing this thesis. Based on the initial dissolution patterns obtained with the novel approach using TRIS, the experimental glasses could be divided into four distinct categories. The initial dissolution patterns of glasses correlated well with the anticipated bioactivity. Moreover, the normalized surface-specific mass loss rates and the different in vivo models and the actual in vivo data correlated well. The results suggest that this type of approach can be used for prescreening the suitability of novel glass compositions for future clinical applications. Furthermore, the results shed light on the possible bioactivity of glasses. An additional goal in this thesis was to gain insight into the phase changes occurring during various heat treatments of glasses with three selected compositions. Engineering-type T-T-T curves for glasses 1-98 and 13-93 were stablished. The information gained is essential in manufacturing amorphous porous implants or for drawing of continuous fibers of the glasses. Although both glasses can be hot worked to amorphous products at carefully controlled conditions, 1-98 showed one magnitude greater nucleation and crystal growth rate than 13-93. Thus, 13-93 is better suited than 1-98 for working processes which require long residence times at high temperatures. It was also shown that amorphous and partially crystalline porous implants can be sintered from bioactive glass S53P4. Surface crystallization of S53P4, forming Na2O∙CaO∙2SiO2, was observed to start at 650°C. The secondary crystals of Na2Ca4(PO4)2SiO4, reported for the first time in this thesis, were detected at higher temperatures, from 850°C to 1000°C. The crystal phases formed affected the dissolution behavior of the implants in simulated body fluid. This study opens up new possibilities for using S53P4 to manufacture various structures, while tailoring their bioactivity by controlling the proportions of the different phases. The results obtained in this thesis give valuable additional information and tools to the state of the art for designing glasses with respect to future clinical applications. With the knowledge gained we can identify different dissolution patters and use this information to improve the tuning of glass compositions. In addition, the novel online analysis approach provides an excellent opportunity to further enhance our knowledge of glass behavior in simulated body conditions.

Production of Mg(OH)2 from Mg-silicate rock for CO2 mineral sequestration

Sequestration of carbon dioxide in mineral rocks, also known as CO2 Capture and Mineralization (CCM), is considered to have a huge potential in stabilizing anthropogenic CO2 emissions. One of the CCM routes is the ex situ indirect gas/sold carbonation of reactive materials, such as Mg(OH)2, produced from abundantly available Mg-silicate rocks. The gas/solid carbonation method is intensively researched at Åbo Akademi University (ÅAU ), Finland because it is energetically attractive and utilizes the exothermic chemistry of Mg(OH)2 carbonation. In this thesis, a method for producing Mg(OH)2 from Mg-silicate rocks for CCM was investigated, and the process efficiency, energy and environmental impact assessed. The Mg(OH)2 process studied here was first proposed in 2008 in a Master’s Thesis by the author. At that time the process was applied to only one Mg-silicate rock (Finnish serpentinite from the Hitura nickel mine site of Finn Nickel) and the optimum process conversions, energy and environmental performance were not known. Producing Mg(OH)2 from Mg-silicate rocks involves a two-staged process of Mg extraction and Mg(OH)2 precipitation. The first stage extracts Mg and other cations by reacting pulverized serpentinite or olivine rocks with ammonium sulfate (AS) salt at 400 - 550 oC (preferably < 450 oC). In the second stage, ammonia solution reacts with the cations (extracted from the first stage after they are leached in water) to form mainly FeOOH, high purity Mg(OH)2 and aqueous (dissolved) AS. The Mg(OH)2 process described here is closed loop in nature; gaseous ammonia and water vapour are produced from the extraction stage, recovered and used as reagent for the precipitation stage. The AS reagent is thereafter recovered after the precipitation stage. The Mg extraction stage, being the conversion-determining and the most energy-intensive step of the entire CCM process chain, received a prominent attention in this study. The extraction behavior and reactivity of different rocks types (serpentinite and olivine rocks) from different locations worldwide (Australia, Finland, Lithuania, Norway and Portugal) was tested. Also, parametric evaluation was carried out to determine the optimal reaction temperature, time and chemical reagent (AS). Effects of reactor types and configuration, mixing and scale-up possibilities were also studied. The Mg(OH)2 produced can be used to convert CO2 to thermodynamically stable and environmentally benign magnesium carbonate. Therefore, the process energy and life cycle environmental performance of the ÅAU CCM technique that first produces Mg(OH)2 and the carbonates in a pressurized fluidized bed (FB) were assessed. The life cycle energy and environmental assessment approach applied in this thesis is motivated by the fact that the CCM technology should in itself offer a solution to what is both an energy and environmental problem. Results obtained in this study show that different Mg-silicate rocks react differently; olivine rocks being far less reactive than serpentinite rocks. In summary, the reactivity of Mg-silicate rocks is a function of both the chemical and physical properties of rocks. Reaction temperature and time remain important parameters to consider in process design and operation. Heat transfer properties of the reactor determine the temperature at which maximum Mg extraction is obtained. Also, an increase in reaction temperature leads to an increase in the extent of extraction, reaching a maximum yield at different temperatures depending on the reaction time. Process energy requirement for producing Mg(OH)2 from a hypothetical case of an iron-free serpentine rock is 3.62 GJ/t-CO2. This value can increase by 16 - 68% depending on the type of iron compound (FeO, Fe2O3 or Fe3O4) in the mineral. This suggests that the benefit from the potential use of FeOOH as an iron ore feedstock in iron and steelmaking should be determined by considering the energy, cost and emissions associated with the FeOOH by-product. AS recovery through crystallization is the second most energy intensive unit operation after the extraction reaction. However, the choice of mechanical vapor recompression (MVR) over the “simple evaporation” crystallization method has a potential energy savings of 15.2 GJ/t-CO2 (84 % savings). Integrating the Mg(OH)2 production method and the gas/solid carbonation process could provide up to an 25% energy offset to the CCM process energy requirements. Life cycle inventory assessment (LCIA) results show that for every ton of CO2 mineralized, the ÅAU CCM process avoids 430 - 480 kg CO2. The Mg(OH)2 process studied in this thesis has many promising features. Even at the current high energy and environmental burden, producing Mg(OH)2 from Mg-silicates can play a significant role in advancing CCM processes. However, dedicated future research and development (R&D) have potential to significantly improve the Mg(OH)2 process performance.

Hartsin likaantuminen ja kestävyys mustalipeän fraktioinnissa kokoekskluusiokromatografialla

Sellunkeiton sivutuotteena syntyvä mustalipeä sisältää arvokkaita orgaanisia yhdisteitä, kuten hydroksihappoja. Toistaiseksi hydroksihapot on käytetty muun mustalipeän tavoin sellutehtaan lämmöntuotantoon. Hydroksihappojen merkitys lämmöntuotannon kannalta on kuitenkin pieni verrattuna mustalipeän sisältämään ligniiniin. Viime vuosina kiinnostus hydroksihappoja kohtaan on kasvanut sillä ne voisivat toimia lähtöaineena monille kemikaaleille, joiden valmistukseen käytetään perinteisesti fossiilisia polttoaineita. Hydroksihappoja voidaan erottaa mustalipeästä useilla eri menetelmillä. Erotukseen soveltuvia menetelmiä ovat esimerkiksi ioniekskluusiokromatografia, kalvosuodatus ja kiteytys sekä kokoekskluusiokromatografia. Kromatografisissa menetelmissä käytetyt hartsit ja kalvosuodatuksessa käytettävät kalvot ovat kuitenkin alttiita eri yhdisteiden aiheuttamalle likaantumiselle. Tämän työn kirjallisuusosassa käsitellään mustalipeän koostumusta sekä mustalipeän sisältämiä hydroksihappoja ja niiden käyttökohteita. Lisäksi kirjallisessa osassa on kuvattu aikaisemmin tutkittuja menetelmiä hydroksihappojen erottamiseksi mustalipeästä. Viimeisin menetelmä mustalipeän fraktioimiseksi on kokoekskluusiokromatografia. Työssä on kuvattu kokoeksluusiokromatografian periaate ja selvitetty menetelmän soveltuvuutta mustalipeän fraktiointiin. Lisäksi on käsitelty kromatografisissa menetelmissä käytettyjen hartsien likaantumista, likaantumisen vaikutusta erotustehokkuuteen ja likaantumisen ehkäisyä. Kokeellisessa osassa käsitellään hydroksihappojen erotusta mustalipeästä kokoekskluusiokromatografialla sekä kokoekskluusiokromatografiassa käytettävän hartsin likaantumista ja kestävyyttä. Työssä selvitettiin toistokokein likaantumisen vaikutusta hartsin erotuskykyyn käsitellyn mustalipeän määrän kasvaessa. Malliaineena käytettiin ultrasuodatettua soodakeitettyä mustalipeää. Tulosten perusteella hartsin likaantuminen ei vaikuttanut hydroksihappojen erotukseen mustalipeästä. Kestävyyskokeissa hartsin vesiretentiossa ei havaittu mittausten perusteella johdonmukaista muutosta. HPLC-analyysien perusteella huomattiin liuoksista kuitenkin mahdollisia hartsin hajoamistuotteita, joita ei kuitenkaan pystytty tunnistamaan.

Membrane development for oil contaminated water treatments

The aim of this Master’s thesis study was to develop a membrane for oil contaminated water treatments. Oily wastewaters are a big problem to environment and therefore it is important to find an efficient method for their treatment. There are several treatment methods, but one of the most promising methods is membrane filtration. In the theoretical part of this study the membrane technology and polymeric membrane preparation with phase inversion and membrane modification methods was discussed. It was also told about the most important properties of the membranes. Oily waters, their treatment methods and oily wastewater sources were discussed more specifically. In the experimental part membranes from cellulose acetate were prepared and membranes were modified with two different methods. Modification methods were surface modification and polymer mixing. The modification purpose was to make membranes more hydrophilic and increase surface charge, which can reduce fouling. Membranes were characterized by determining zeta potential, contact angle, oil retention, pure water permeability, pressure-normalized flux and fouling. It were used both synthetic and real spent oil-water emulsion in membrane filtration. Surface modification resulted membranes, which had better properties than unmodified membrane. The amount of substance used in surface modification affected a lot to membrane properties, so it would be necessary to try different amounts of substance to develop the best membrane for oil-water emulsion treatment.

Influence of reactant absorption and dissolution in heterogeneous precipitation processes

In this research work, the aim was to investigate the volumetric mass transfer coefficient [kLa] of oxygen in stirred tank in the presence of solid particle experimentally. The kLa correlations as a function of propeller rotation speed and flow rate of gas feed were studied. The O2 and CO2 absorption in water and in solid-liquid suspensions and heterogeneous precipitation of MgCO3 were thoroughly examined. The absorption experiments of oxygen were conducted in various systems like pure water and in aqueous suspensions of quartz and calcium carbonate particles. Secondly, the precipitation kinetics of magnesium carbonate was also investigated. The experiments were performed to study the reactive crystallization with magnesium hydroxide slurry and carbon dioxide gas by varying the feed rates of carbon dioxide and rotation speeds of mixer. The results of absorption and precipitation are evaluated by titration, total carbon (TC analysis), and ionic chromatrography (IC). For calcium carbonate, the particle concentration was varied from 17.4 g to 2382 g with two size fractions: 5 µm and 45-63 µm sieves. The kLa and P/V values of 17.4 g CaCO3 with particle size of 5µm and 45-63 µm were 0.016 s-1 and 2400 W/m3. At 69.9 g concentration of CaCO3, the achieved kLa is 0.014 s-1 with particle size of 5 µm and 0.017 s-1 with particle size of 45 to 63 µm. Further increase in concentration of calcium carbonate, i.e. 870g and 2382g , does not affect volumetric mass transfer coeffienct of oxygen. It could be concluded from absorption results that maximum value of kLa is 0.016 s-1. Also particle size and concentration does affect the transfer rate to some extend. For precipitation experiments, the constant concentration of Mg(OH)2 was 100 g and the rotation speed varied from 560 to 750 rpm, whereas the used feed rates of CO2 were 1 and 9 L/min. At 560 rpm and feed rate of CO2 is 1 L/min, the maximum value of Mg ion and TC were 0.25 mol/litre and 0.12 mol/litre with the residence time of 40 min. When flow rate of CO2 increased to 9 L/min with same 560 rpm, the achieved value of Mg and TC were 0.3 mol/litre and 0.12 mol/L with shorter residence time of 30 min. It is concluded that feed rate of CO2 is dominant in precipitation experiments and it has a key role in dissociation and reaction of magnesium hydroxide in precipitation of magnesium carbonate.

CFD modeling of dispersion water feed in wastewater cleaning application

Fluid particle breakup and coalescence are important phenomena in a number of industrial flow systems. This study deals with a gas-liquid bubbly flow in one wastewater cleaning application. Three-dimensional geometric model of a dispersion water system was created in ANSYS CFD meshing software. Then, numerical study of the system was carried out by means of unsteady simulations performed in ANSYS FLUENT CFD software. Single-phase water flow case was setup to calculate the entire flow field using the RNG k-epsilon turbulence model based on the Reynolds-averaged Navier-Stokes (RANS) equations. Bubbly flow case was based on a computational fluid dynamics - population balance model (CFD-PBM) coupled approach. Bubble breakup and coalescence were considered to determine the evolution of the bubble size distribution. Obtained results are considered as steps toward optimization of the cleaning process and will be analyzed in order to make the process more efficient.

Fosforin talteenotto eri saostus- ja kiteytysmenetelmillä

Fosfori on elintärkeä alkuaine ravinteena ja haasteena on, että fosforivarannot ovat yleismaailmallisesti ehtymässä. Sen kiertokulussa merkittävä osa päätyy vesistöihin aiheuttaen rehevöitymistä. Ongelmaan etsittiin ratkaisua fosforin saostus- ja kiteytysmenetelmistä. Kandityössä esitettiin eri periaatteet erottaa fosfori jätevedestä. Prosesseihin vaikuttavat tekijät määritettiin kiteytysteorian ja kirjallisuudesta löytyvien tutkimusten pohjalta, joiden avulla voitiin määrittää lupaavimmat menetelmät talteenottaa fosfori. Lupaavimmiksi yhdisteiksi saostaa fosfori osoittautuivat magnesiumammoniumfosfaatti- tai hydroksiapatiitti saostusprosessi.

Haihdutusnopeuksien määritys glysiinin alipainekiteytyksessä

Alipainekiteytyksessä tasalaatuisen lopputuotteen valmistamiseksi kiteytysolosuhteiden vaikutus liuottimen haihtumisvuohon ja kiteiden ominaisuuksiin on huomioitava. Kandidaatin työn tavoitteena oli selvittää, miten glysiinin alipainekiteytyksessä vesiliuoksesta kiteytysolosuhteet (lämpötila ja paine) vaikuttavat liuottimen haihtumisvuohon ja syntyvien kiteiden polymorfiaan. Haihdutuskokeet suoritettiin puhtaalle vedelle ja alipainekiteytyskokeet glysiinin 95 % kylläiselle vesiliuokselle lämpötiloissa 40 °C, 50 °C ja 60 °C ja paineissa 40 mbar, 60 mbar ja 80 mbar. Kiteyttimenä käytettiin suljettua, virtaushaitoilla, sekoittimella ja ohjausputkella varustettua reaktoria johon oli kytketty alipainepumppu ja termostaatti paineen ja lämpötilan ohjaamiseksi. Nesteen määrä haihdutuskokeissa oli 2 kg ja alipainekiteytyskokeissa 1,2 kg. Osa alipainekiteytyskokeista saaduista kiteistä analysoitiin jauheröntgendiffraktioanalysaattorin (PXRD, engl. powder x-ray diffraction) avulla. Kaikki PXRD-laitteella analysoidut alipainekiteytyskokeissa saadut kiteet osoittautuivat glysiinin γ-polymorfiksi. Kiteytysolosuhteilla oli selkeä vaikutus haihtumisvuohon, mutta vaikutusta glysiinikiteiden polymorfiaan ei havaittu koealueella.

Modification of commercial poly-lactide for extrusion coated food packaging applications

Poly-L-lactide (PLLA) is a widely used sustainable and biodegradable alternative to replace synthetic non-degradable plastic materials in the packaging industry. Conversely, its processing properties are not always optimal, e.g. insufficient melt strength at higher temperatures (necessary in extrusion coating processes). This thesis reports on research to improve properties of commercial PLLA grade (3051D from NatureWorks), to satisfy and extend end-use applications, such as food packaging by blending with modified PLLA. Adjustment of the processability by chain branching of commercial poly-L-lactide initiated by peroxide was evaluated. Several well-defined branched structures with four arms (sPLLA) were synthesized using pentaerythritol as a tetra-functional initiator. Finally, several block copolymers consisting of polyethylene glycol and PLLA (i.e. PEGLA) were produced to obtain a well extruded material with improved heat sealing properties. Reactive extrusion of poly-L-lactide was carried out in the presence of 0.1, 0.3 and 0.5 wt% of various peroxides [tert-butyl-peroxybenzoate (TBPB), 2,5-dimethyl-2,5-(tert-butylperoxy)-hexane (Lupersol 101; LOL1) and benzoyl peroxide (BPO)] at 190C. The peroxide-treated PLLAs showed increased complex viscosity and storage modulus at lower frequencies, indicating the formation of branched/cross linked architectures. The material property changes were dependent on the peroxide, and the used peroxide concentration. Gel fraction analysis showed that the peroxides, afforded different gel contents, and especially 0.5 wt% peroxide, produced both an extremely high molar mass, and a cross linked structure, not perhaps well suited for e.g. further use in a blending step. The thermal behavior was somewhat unexpected as the materials prepared with 0.5 wt% peroxide showed the highest ability for crystallization and cold crystallization, despite substantial cross linking. The peroxide-modified PLLA, i.e. PLLA melt extruded with 0.3 wt% of TBPB and LOL1 and 0.5 wt% BPO was added to linear PLLA in ratios of 5, 15 and 30 wt%. All blends showed increased zero shear viscosity, elastic nature (storage modulus) and shear sensitivity. All blends remained amorphous, though the ability of annealing was improved slightly. Extrusion coating on paperboard was conducted with PLLA, and peroxide-modified PLLA blends (90:10). All blends were processable, but only PLLA with 0.3 wt% of LOL1 afforded a smooth high quality surface with improved line speed. Adhesion levels between fiber and plastic, as well as heat seal performance were marginally reduced compared with pure 3051D. The water vapor transmission measurements (WVTR) of the blends containing LOL1 showed acceptable levels, only slightly lower than for comparable PLLA 3051D. A series of four-arm star-shaped poly-L-lactide (sPLLA) with different branch length was synthesized by ring opening polymerization (ROP) of L-lactide using pentaerythritol as initiator and stannous octoate as catalyst. The star-shaped polymers were further blended with its linear resin and studied for their melt flow and thermal properties. Blends containing 30 wt% of sPLLA with low molecular weight (30 wt%; Mwtotal: 2500 g mol-1 and 15000 g mol-1) showed lower zero shear viscosity and significantly increased shear thinning, while at the same time slightly increased crystallization of the blend. However, the amount of crystallization increased significantly with the higher molecular weight sPLLA, therefore the star-shaped structure may play a role as nucleating agent. PLLA-polyethylene glycol–PLLA triblock copolymers (PEGLA) with different PLLA block length were synthesized and their applicability as blends with linear PLLA (3051D NatureWorks) was investigated with the intention of improving heat-seal and adhesion properties of extrusion-coated paperboard. PLLA-PEG-PLLA was obtained by ring opening polymerization (ROP) of L-lactide using PEG (molecular weight 6000 g mol-1) as an initiator, and stannous octoate as catalyst. The structures of the PEGLAs were characterized by proton nuclear magnetic resonance spectroscopy (1H-NMR). The melt flow and thermal properties of all PEGLAs and their blends were evaluated using dynamic rheology, and differential scanning calorimeter (DSC). All blends containing 30 wt% of PEGLAs showed slightly higher zero shear viscosity, higher shear thinning and increased melt elasticity (based on tan delta). Nevertheless, no significant changes in thermal properties were distinguished. High molecular weight PEGLAs were used in extrusion coating line with 3051D without problems.

Utilizing hemicelluloses – the first step : controlled extraction with hot water

Människor utnyttjar ofta kemi mångsidigt i sitt vardagliga liv utan att närmare tänka på detaljerna. Nuförtiden kan man framställa en ökande mängd av produkter ur förnybara råmaterial och en av de mest mångsidiga nybara råmaterialet i Norden är barrträd. Den lyriska lägerelden eller spiselden och möbler av ved samt papper är en väsentlig del av vardagen. Också livsmedel och läkemedel kan innehålla föreningar ur ved. Ved som råmaterial består av tre huvudkomponenten: cellulosa, som är uppbyggd av druvsockermolekyler är en långkedjad, oförgrenad polymer; lignin, som sammanhåller fibrerna i vedmaterialet som lim samt hemicellulosor, som ofta är uppbyggda av olika sockerarter och är en förgrenad polymer. Följaktligen består vedmaterialet av 70 % socker. I detta arbete har vi koncentrerat på i hemicellulosa och dess extraktion ur gran, samt bestämning av hemicellulosans egenskaper. Den slutliga målsättningen i forskningen var att skapa nya produkter ur gran. Forskning i extraktionens hemligheter eller hur hemicellulosa kan effektivt extraheras i den önskade formen kräver nya typers experimentellasanläggningar och experiment samt matematisk modellering. Den långkedjade hemicellulosan är lämplig för att användas t.ex. i skyddshinnor eller i livsmedel. Medel- och småmolekylär hemicellulosa kan användas som utgångsämne för framställning av bränslen, smörjmedel, sockersyror och alkoholer, av vilka xylitol är mest känd för alla pga hälsobefrämjande effekter. Det är utomordentligt viktigt ur miljöns och energiekonomins synvinkel att sträva efter effektivering av utnyttjandet av den värdefullaste och största naturtillgången, skogen i vårt land, med alla möjliga sätt. Resultaten av denna forskning utnyttjar avsevärt den växande, nya, på skogen baserande biobaseradeindustrin, som framställer nya spetsprodukter samt skapar nya arbetsplatser. ----------------------------------------------------- Ihmiset hyödyntävät usein huomaamattaan kemiaa monipuolisesti jokapäiväisessä elämässä. Nykyään kasvava määrä tuotteista kyetään valmistamaan uusiutuvista raaka-aineista ja yksi monipuolisimmista uusiutuvista luonnonvaroistamme pohjolassa ovat havupuut. Tunnelmallinen nuotio tai takkatuli ja puiset huonekalut sekä paperi ovat olennainen osa arkea. Myös elintarvikkeet ja lääkkeet voivat sisältää puusta peräisin olevia yhdisteitä. Puu materiaalina koostuu rakenteeltaan pääosin kolmesta osasta; selluloosasta, joka on rypälesokerista koostuva pitkäketjuinen haaroittumaton polymeeri, ligniinistä, joka toimii puun koossa pitävänä liima-aineena ja hemiselluloosasta, joka on useista eri sokereista rakentunut haaroittunut polymeeri. Näin ollen puusta 70 % on sokeria. Tässä työssä olemme keskittyneet hemiselluloosaan ja sen uuttamiseen kuusesta, sekä ominaisuuksien kartoittamiseen. Tutkimusaiheen lopullinen tavoite on luoda uusia tuotteita kuusesta. Uuton salojen tutkiminen eli miten hemiselluloosa saadaan tehokkaasti uutettua halutunlaisena vaatii uudenlaisia koelaitteistoja ja kokeita, sekä matemaattista mallintamista. Suurikokoinen hemiselluloosa on sopivaa käytettäväksi esimerkiksi suojakalvoissa tai elintarvikkeissa. Keskikokoista ja pienimolekyylistä hemiselluloosaa voidaan käyttää lähtöaineena valmistettaessa polttoaineita, voiteluaineita, sokerihappoja ja sokerialkoholeja, joista xylitoli on terveysvaikutustensa vuoksi kaikille tuttu. Niin ympäristömme kuin myös energiataloutemme kannalta on ensiarvoisen tärkeää pyrkiä kaikin keinoin tehostamaan maallemme arvokkaan, sekä luonnonvaroistamme yhden suurimman, metsän, vastuullista hyödyntämistä. Tämän tutkimuksen tulokset hyödyntävät merkittävästi maahamme nousevaa uutta metsään pohjautuvaa biojalostusteollisuutta, joka valmistaa uusia huipputuotteita sekä luo työpaikkoja.