Pressure filtration characteristics of enzymatically hydrolyzed biomass suspensions

Enzymatic hydrolysis of lignocellulosic polymers is likely to become one of the key technologies enabling industrial production of liquid biofuels and chemicals from lignocellulosic biomass. Certain types of enzymes are able to hydrolyze cellulose and hemicellulose polymers to shorter units and finally to sugar monomers. These monomeric sugars are environmentally acceptable carbon sources for the production of liquid biofuels, such as bioethanol, and other chemicals, such as organic acids. Liquid biofuels in particular have been shown to contribute to the reduction of net emissions of greenhouse gases. The solid residue of enzymatic hydrolysis is composed mainly of lignin and partially degraded fibers, while the liquid phase contains the produced sugars. It is usually necessary to separate these two phases at some point after the hydrolysis stage. Pressure filtration is an efficient technique for this separation. Solid-liquid separation of biomass suspensions is difficult, because biomass solids are able to retain high amounts of water, which cannot be readily liberated by mechanical separation techniques. Most importantly, the filter cakes formed from biomaterials are compressible, which ultimately means that the separation may not be much improved by increasing the filtration pressure. The use of filter aids can therefore facilitate the filtration significantly. On the other hand, the upstream process conditions have a major influence on the filtration process. This thesis investigates how enzymatic hydrolysis and related process conditions affect the filtration properties of a cardboard suspension. The experimental work consists of pressure filtration and characterization of hydrolysates. The study provides novel information about both issues, as the relationship between enzymatic hydrolysis conditions and subsequent filtration properties has so far not been considered in academic studies. The results of the work reveal that the final degree of hydrolysis is an important factor in the filtration stage. High hydrolysis yield generally increases the average specific cake resistance. Mixing during the hydrolysis stage resulted in undefined changes in the physical properties of the solid residue, causing a high filtration resistance when the mixing intensity was high. Theoretical processing of the mixing data led to an interesting observation: the average specific cake resistance was observed to be linearly proportional to the mixer shear stress. Another finding worth attention is that the size distributions of the solids did not change very dramatically during enzymatic hydrolysis. There was an observable size reduction during the first couple of hours, but after that the size reduction was minimal. Similarly, the size distribution of the suspended solids remained almost constant when the hydrolyzed suspension was subjected to intensive mixing. It was also found that the average specific cake resistance was successfully reduced by the use of filter aids. This reduction depended on the method of how the filter aids were applied. In order to obtain high filtration capacity, it is recommended to use the body feed mode, i.e. to mix the filter aid with the slurry prior to filtration. Regarding the quality of the filtrate, precoat filtration was observed to produce a clear filtrate with negligible suspended solids content, while the body feed filtrates were turbid, irrespective of which type of filter aid was used.

Intensification of hemicellulose hot-water extraction from spruce wood by parameter tuning

The growing population on earth along with diminishing fossil deposits and the climate change debate calls out for a better utilization of renewable, bio-based materials. In a biorefinery perspective, the renewable biomass is converted into many different products such as fuels, chemicals, and materials, quite similar to the petroleum refinery industry. Since forests cover about one third of the land surface on earth, ligno-cellulosic biomass is the most abundant renewable resource available. The natural first step in a biorefinery is separation and isolation of the different compounds the biomass is comprised of. The major components in wood are cellulose, hemicellulose, and lignin, all of which can be made into various end-products. Today, focus normally lies on utilizing only one component, e.g., the cellulose in the Kraft pulping process. It would be highly desirable to utilize all the different compounds, both from an economical and environmental point of view. The separation process should therefore be optimized. Hemicelluloses can partly be extracted with hot-water prior to pulping. Depending in the severity of the extraction, the hemicelluloses are degraded to various degrees. In order to be able to choose from a variety of different end-products, the hemicelluloses should be as intact as possible after the extraction. The main focus of this work has been on preserving the hemicellulose molar mass throughout the extraction at a high yield by actively controlling the extraction pH at the high temperatures used. Since it has not been possible to measure pH during an extraction due to the high temperatures, the extraction pH has remained a “black box”. Therefore, a high-temperature in-line pH measuring system was developed, validated, and tested for hot-water wood extractions. One crucial step in the measurements is calibration, therefore extensive efforts was put on developing a reliable calibration procedure. Initial extractions with wood showed that the actual extraction pH was ~0.35 pH units higher than previously believed. The measuring system was also equipped with a controller connected to a pump. With this addition it was possible to control the extraction to any desired pH set point. When the pH dropped below the set point, the controller started pumping in alkali and by that the desired set point was maintained very accurately. Analyses of the extracted hemicelluloses showed that less hemicelluloses were extracted at higher pH but with a higher molar-mass. Monomer formation could, at a certain pH level, be completely inhibited. Increasing the temperature, but maintaining a specific pH set point, would speed up the extraction without degrading the molar-mass of the hemicelluloses and thereby intensifying the extraction. The diffusion of the dissolved hemicelluloses from the wood particle is a major part of the extraction process. Therefore, a particle size study ranging from 0.5 mm wood particles to industrial size wood chips was conducted to investigate the internal mass transfer of the hemicelluloses. Unsurprisingly, it showed that hemicelluloses were extracted faster from smaller wood particles than larger although it did not seem to have a substantial effect on the average molar mass of the extracted hemicelluloses. However, smaller particle sizes require more energy to manufacture and thus increases the economic cost. Since bark comprises 10 – 15 % of a tree, it is important to also consider it in a biorefinery concept. Spruce inner and outer bark was hot-water extracted separately to investigate the possibility to isolate the bark hemicelluloses. It was showed that the bark hemicelluloses comprised mostly of pectic material and differed considerably from the wood hemicelluloses. The bark hemicelluloses, or pectins, could be extracted at lower temperatures than the wood hemicelluloses. A chemical characterization, done separately on inner and outer bark, showed that inner bark contained over 10 % stilbene glucosides that could be extracted already at 100 °C with aqueous acetone.

Production unit’s overhead cost allocation with activity-based costing in food industry enterprise

The main objective of this Master’s thesis is to develop a cost allocation model for a leading food industry company in Finland. The goal is to develop an allocation method for fixed overhead expenses produced in a specific production unit and create a plausible tracking system for product costs. The second objective is to construct an allocation model and modify the created model to be suited for other units as well. Costs, activities, drivers and appropriate allocation methods are studied. This thesis is started with literature review of existing theory of ABC, inspecting cost information and then conducting interviews with officials to get a general view of the requirements for the model to be constructed. The familiarization of the company started with becoming acquainted with the existing cost accounting methods. The main proposals for a new allocation model were revealed through interviews, which were utilized in setting targets for developing the new allocation method. As a result of this thesis, an Excel-based model is created based on the theoretical and empiric data. The new system is able to handle overhead costs in more detail improving the cost awareness, transparency in cost allocations and enhancing products’ cost structure. The improved cost awareness is received by selecting the best possible cost drivers for this situation. Also the capacity changes are taken into consideration, such as usage of practical or normal capacity instead of theoretical is suggested to apply. Also some recommendations for further development are made about capacity handling and cost collection.

Lignin oxidation by PCD technology

The purpose of this study is to investigate whether commercial Kraft lignin can be treated with pulsed corona discharge apparatus so that it becomes active. Active lignin refers to the kind of lignin that can be precipitated on the surface of a fiber by lowering the pH. A secondary agenda here is to remove the pungent smell of kraft lignin, which is caused by organically bound sulfur. It is expected that the study will identify mild processing conditions and parameters for achievement of the desired outcome. In the literature review, the properties of lignin are explained, as is their impact on any further processing. In addition, a number of processes are described for the oxidation of lignin in a variety of applications. In the experimental part of the study, test runs were conducted to determine the effects of oxygen supply and pulse frequency on oxidation results, where the purpose is to produce reactive lignin and to find a process that is feasible at an industrial scale. Based on the reported experiments, lignin could not be made active or precipitated to the surface of the fiber. Actual changes in the structure of lignin were not observed, but the pungent smell of lignin was removed. The exact reason for this change could not be established because sulfur NMR analysis did not work for the lignin samples.

Separation of lignin in Pulp Mill process and its effect on sodium sulphur balance

The aim of this thesis is to define effects of lignin separation process on Pulp mill chemical balance especially on sodium/sulphur-balance. The objective is to develop a simulation model with WinGEMS Process Simulator and use that model to simulate the chemical balances and process changes. The literature part explains what lignin is and how kraft pulp is produced. It also introduces to the methods that can be used to extract lignin from black liquor stream and how those methods affect the pulping process. In experimental part seven different cases are simulated with the created simulation model. The simulations are based on selected reference mill that produces 500 000 tons of bleached air-dried (90 %) pulp per year. The simulations include the chemical balance calculation and the estimated production increase. Based on the simulations the heat load of the recovery boiler can be reduced and the pulp production increased when lignin is extracted. The simulations showed that decreasing the waste acid stream intake from the chlorine dioxide plant is an effective method to control the sulphidity level when about 10 % of lignin is extracted. With higher lignin removal rates the in-mill sulphuric acid production has been discovered to be a better alternative to the sulphidity control.

Chemical changes in biomass during torrefaction

Torrefaction is moderate thermal treatment (~200-300 °C) of biomass in an inert atmosphere. The torrefied fuel offers advantages to traditional biomass, such as higher heating value, reduced hydrophilic nature, increased its resistance to biological decay, and improved grindability. These factors could, for instance, lead to better handling and storage of biomass and increased use of biomass in pulverized combustors. In this work, we look at several aspects of changes in the biomass during torrefaction. We investigate the fate of carboxylic groups during torrefaction and its dependency to equilibrium moisture content. The changes in the wood components including carbohydrates, lignin, extractable materials and ashforming matters are also studied. And at last, the effect of K on torrefaction is investigated and then modeled. In biomass, carboxylic sites are partially responsible for its hydrophilic characteristic. These sites are degraded to varying extents during torrefaction. In this work, methylene blue sorption and potentiometric titration were applied to measure the concentration of carboxylic groups in torrefied spruce wood. The results from both methods were applicable and the values agreed well. A decrease in the equilibrium moisture content at different humidity was also measured for the torrefied wood samples, which is in good agreement with the decrease in carboxylic group contents. Thus, both methods offer a means of directly measuring the decomposition of carboxylic groups in biomass during torrefaction as a valuable parameter in evaluating the extent of torrefaction. This provides new information to the chemical changes occurring during torrefaction. The effect of torrefaction temperature on the chemistry of birch wood was investigated. The samples were from a pilot plant at Energy research Center of the Netherlands (ECN). And in that way they were representative of industrially produced samples. Sugar analysis was applied to analyze the hemicellulose and cellulose content during torrefaction. The results show a significant degradation of hemicellulose already at 240 °C, while cellulose degradation becomes significant above 270 °C torrefaction. Several methods including Klason lignin method, solid state NMR and Py-GC-MS analyses were applied to measure the changes in lignin during torrefaction. The changes in the ratio of phenyl, guaiacyl and syringyl units show that lignin degrades already at 240 °C to a small extent. To investigate the changes in the extractives from acetone extraction during torrefaction, gravimetric method, HP-SEC and GC-FID followed by GC-MS analysis were performed. The content of acetone-extractable material increases already at 240 °C torrefaction through the degradation of carbohydrate and lignin. The molecular weight of the acetone-extractable material decreases with increasing the torrefaction temperature. The formation of some valuable materials like syringaresinol or vanillin is also observed which is important from biorefinery perspective. To investigate the change in the chemical association of ash-forming elements in birch wood during torrefaction, chemical fractionation was performed on the original and torrefied birch samples. These results give a first understanding of the changes in the association of ashforming elements during torrefaction. The most significant changes can be seen in the distribution of calcium, magnesium and manganese, with some change in water solubility seen in potassium. These changes may in part be due to the destruction of carboxylic groups. In addition to some changes in water and acid solubility of phosphorous, a clear decrease in the concentration of both chlorine and sulfur was observed. This would be a significant additional benefit for the combustion of torrefied biomass. Another objective of this work is studying the impact of organically bound K, Na, Ca and Mn on mass loss of biomass during torrefaction. These elements were of interest because they have been shown to be catalytically active in solid fuels during pyrolysis and/or gasification. The biomasses were first acid washed to remove the ash-forming matters and then organic sites were doped with K, Na, Ca or Mn. The results show that K and Na bound to organic sites can significantly increase the mass loss during torrefaction. It is also seen that Mn bound to organic sites increases the mass loss and Ca addition does not influence the mass loss rate on torrefaction. This increase in mass loss during torrefaction with alkali addition is unlike what has been found in the case of pyrolysis where alkali addition resulted in a reduced mass loss. These results are important for the future operation of torrefaction plants, which will likely be designed to handle various biomasses with significantly different contents of K. The results imply that shorter retention times are possible for high K-containing biomasses. The mass loss of spruce wood with different content of K was modeled using a two-step reaction model based on four kinetic rate constants. The results show that it is possible to model the mass loss of spruce wood doped with different levels of K using the same activation energies but different pre-exponential factors for the rate constants. Three of the pre-exponential factors increased linearly with increasing K content, while one of the preexponential factors decreased with increasing K content. Therefore, a new torrefaction model was formulated using the hemicellulose and cellulose content and K content. The new torrefaction model was validated against the mass loss during the torrefaction of aspen, miscanthus, straw and bark. There is good agreement between the model and the experimental data for the other biomasses, except bark. For bark, the mass loss of acetone extractable material is also needed to be taken into account. The new model can describe the kinetics of mass loss during torrefaction of different types of biomass. This is important for considering fuel flexibility in torrefaction plants.