Epäpuhtausmetallien talteenotto sinkkiprosessissa

There are small amounts of valuable metals, such as indium, gallium and germanium, in zinc process solutions. Their solvent extraction was studied in this work in sulphate solutions containing zinc and other metals present in industrial solutions. It was discovered, that a commercial bis(2-ethylhexyl)phosphate (D2EHPA) extractant can be used to extract indium and gallium. Indium was extracted separately at a higher acid concentration than gallium. Zinc was co-extracted faster than gallium and almost as much as gallium at the same pH. However, the scrubbing of zinc was possible using a dilute sulphuric acid and a short contact time while gallium losses were small. Both indium and gallium were stripped with sulphuric acid. Germanium was extracted with 5,8-diethyl-7-hydroxydodecane-6-oxime with the commercial name of LIX 63. Unlike other metals in the solution the extraction of germanium increased with different extractants as the acidity increased. Germanium extraction isotherm was measured for a 125 g/L sulfuric acid solution. The loaded organic phase was washed with pure water. It removed the co-extracted acid and part of the germanium and extracted impurities such as iron and copper. Germanium was stripped using a NaOH solution. A process model utilizing own experimentally determined extraction, scrubbing and stripping isotherms was made with HSC Sim software developed by Outotec Oyj. The model based on McCabe–Thiele diagrams was used in sizing the necessary amount of stages and phase ratios in a recovery process. It was concluded, that indium, gallium and germanium can be recovered in the process from a feed where their concentrations are low (<300 ppm). In an example case the feed contained also more than 20 g/L zinc and 2–8 g/L iron, aluminium and copper. The recoveries of indium, gallium and germanium were more than 90 % when 1–3 stages were used in each extraction, scrubbing and stripping section. Since the number of stages is small mixer-settlers would be well suited for this purpose.

Metallien eluointi kelatoivasta ioninvaihtimesta

Kelatoivat ioninvaihtimet ovat yleensä makrohuokoisia hartseja, joiden avulla metalleja poistetaan ja otetaan mahdollisesti talteen teollisuuden puhdistettavista jätevirroista. Ne muodostavat metalli-ionien kanssa komplekseja runkomateriaaliin kovalenttisesti liitettyjen aktiivisten funktionaalisten ryhmiensä välityksellä. Ioninvaihtimen selektiivisyys eri metalli-ioneja kohtaan vaihtelee riippuen siihen liitetystä kelatoivasta ryhmästä. Työssä tutkitaan metallien tarttumista kelatoiviin ioninvaihtimiin, sekä niiden eluoitumista adsorbentistaan. Kelatoivat ioninvaihtimet sitovat metalli-ioneja tehokkaasti ligandiensa monihampaisuudesta johtuen. Metallien tarttuminen kelatoivaan ioninvaihtimeen ei kuitenkaan ole yksiselitteistä, vaan siihen vaikuttaa muun muassa pH yhdessä monen muun tekijän kanssa. Ioninvaihtimien selektiivisyyttä tarkastellaan työssä lähinnä kovien ja pehmeiden happojen ja emästen HSAB -teorian näkökulmasta. Regeneroinnilla ioninvaihdin saadaan jälleen alkuperäiseen muotoonsa, minkä jälkeen se voidaan käyttää uudelleen. Yleensä regenerointi suoritetaan kemiallisesti. Tässä työssä ioninvaihtimien regenerointia ja kohdemetallin eluointia tarkastellaan paitsi teoriassa, myös kokeellisessa osuudessa. Kokeellisessa osuudessa tutkitaan kuparin (Cu2+) eluoitumista kelatoivasta Dowex M-4195 kationinvaihtohartsista. Kokeissa hartsi ladattiin kuparilla erillisessä panoksessa kuparin ollessa syöttöliuoksessa kuparisulfaattina. Eluointiliuoksina käytettiin 2 ja 5 molaarista rikkihappoa, sekä 2 molaarista ammoniumhydroksidia. Eluointi suoritettiin panostoimisena kolonniajona ja eluaatista otetut näytteet analysoitiin atomiadsorptiospektrofotometrillä. Analyysitulokset esitetään läpäisykäyrinä, joiden perusteella 2M ammoniumhydroksidi on kolmesta tutkitusta eluentista tehokkain eluoimaan kuparia Dowex M-4195 hartsista.

Paineohjatulla sytytyksellä varustetun soihdun rakenne

FGG Finngas GmbH sivuliike Suomessa operoi LPG-kaasuterminaalia Haminan kaasusatamassa. Yrityksen terminaalin alueella varastoidaan, puretaan ja lastataan erilaisia nestekaasuja. Yrityksellä on käytössään soihtujärjestelmä, jolla voidaan polttaa nestekaasujen käsittelystä aiheutunut ylijäämäkaasu, jota ei voida hyödyntää. Soihtujärjestelmä toimii myös turvalaitteena häiriötilanteiden varalta. Tässä kandidaatintyössä esitellään ja dokumentoidaan yrityksen soihtujärjestelmän tämänhetkinen rakenne. Soihdun kannalta olennaiset osajärjestelmät ja niiden toiminta sekä rakenne on esitelty omina kokonaisuuksinaan. Järjestelmän sähköisen toiminnan tutkimisessa on perehdytty sytytysjärjestelmään. Kandidaatintyön tulokset mahdollistavat soihtujärjestelmän toimintavarmuuden parantamisen. Lisäksi työ toimii koostettuna dokumenttina soihtujärjestelmän tämänhetkisestä tilasta sekä toimilaitteista.

Pituussuunnassa hitsatun rakenneputken väsymislujuus HF –hitsausta käytettäessä

Tässä diplomityössä määritettiin pituussuunnassa hitsatun rakenneputken väsymislujuus HF –hitsausta käytettäessä. Työn tavoitteena oli vertailla eri jälkikäsittelyjen ja kahden eri materiaalin vaikutusta väsymislujuuteen. Materiaaleina kokeissa oli Ruukki double grade ja Optim 700 Plus MH. Eurokoodi 3 ja IIW määrittelee kiinnityshitseille väsymiskestävyysluokaksi 125-140, kun SN -käyrän kaltevuus, m = 3. Koetuloksia vertailtiin näihin valmiiksi määriteltyihin väsymiskestävyysluokkiin. Ruukki Metals Oy toimitti koemateriaalin kahdenlaisia väsytyskokeita varten, joiden avulla väsymislujuus voitiin määrittää. Ensimmäinen koe suoritettiin värähtelyllä hyödyntäen rakenneputken ominaistaajuutta, jolloin kuormituksen rajajännityssuhde on -1. Toinen väsytyskoe suoritettiin rakenneputkista leikatuille väsytyssauvoille, missä pituussuuntainen HF –hitsi on keskellä sauvaa. Tämä väsytyskoe suoritettiin vetotykytyksellä rajajännityssuhteella 0,1. Väsytyskokeissa havaittiin, että kiinnityshitsi täyttää sille asetetut vaatimukset, koska murtumat tapahtuivat perusaineesta. Tällöin koetuloksia vertaillaan Eurokoodi 3:n perusaineen väsymisluokkaan 160, SN -käyrän kaltevuudella m = 5. Kaikkien koetulosten väsymiskestävyysluokan keskiarvoksi saatiin 185 95 %:n todennäköisyydellä. Tutkimuksessa saatiin arvokasta tietoa kahden eri materiaalin väsymislujuudesta. Materiaalilla ei kuitenkaan havaittu vaikutusta lujuuteen. Eri jälkikäsittelyt eli juuren puolen metallipurseen höyläys tai pituussuuntaisen hitsisauman hehkutus eivät vaikuttaneet väsymislujuuteen. Kokeissa väsymismurtuma ydintyi rakenneputken pinnalta olevista alkuvioista, joten putkien käsittelyä valmistuksen jälkeen voitaisiin parantaa.

Vääntökuormitetun koteloprofiilipuomin väsymiskestävyys

Tässä työssä tutkittiin vääntökuormitettua hitsattua koteloprofiilipuomia. Vääntökuormitus aiheuttaa koteloprofiiliin vinouttavan voimasysteemin, joka aiheuttaa kotelopalkkiin sekä poikittaisia taivutusjännityksiä että pitkittäisiä jännityksiä. Vinoutumisen aiheuttamia lisära-situksia on tutkittu analyyttisesti BEF-analogian avulla sekä elementtimenetelmää apuna käyttäen. Lisäksi vääntökuormitus aiheuttaa puomiin estetyn väännön jännityksiä. Väsymiskestoikää tutkittiin laboratoriossa suoritettujen väsytyskokeiden avulla sekä las-kennallisesti. Kestoikälaskennassa käytettiin tehollisen lovijännityksen menetelmää hitsin juuren puolen väsymisen arvioinnissa sekä hot spot- jännityksen menetelmää hitsin rajavii-van väsymisen arvioinnissa. Teholliset lovijännitykset sekä hot spot jännitykset ovat määri-tetty elementtimenetelmän avulla. Laboratoriokokeiden ja elementtimenetelmä laskennan perusteella saatiin rakenteen kes-toiän kannalta kriittiset detaljit määritettyä. Kriittiset detaljit sijaitsevat puomin päädyn rakenteissa. Tutkimuksessa saatiin selville, että kriittisten detaljien rakenteellisilla ja valmis-tusteknisillä ratkaisuilla on merkittävä vaikutus lopullisen tuotteen väsymiskestoikään.

Kun vaan rehtori on korvat auki. Koulun kehittämisellä pedagogista hyvinvointia

Tämän tutkimuksen tarkoituksena on tutkia perusopetuksen rehtoreiden käsityksiä siitä, miten rehtori johtaa opettajakuntaansa ja koulua oppivan organisaation suuntaan. Tutkimus etsii vastauksia koulun kehittämisen ja pedagogisen hyvinvoinnin yhtymäkohtiin. Tutkimus on perusopetuksen rehtoreiden keskuudessa Salossa tehty tapaustutkimus, jonka tiedonkeruu ajoittui vuosille 2008–2011. Tutkimuksen ensimmäinen osa oli tulevaisuusverstas (n=14). Verstaan pohjalta tutkimukselle syntyi teoreettinen viitekehys ja aineiston keräämistä jatkettiin puolistrukturoidulla teemahaastattelulla (n=14). Tulokset toimitettiin nettiportaaliin, jossa haastatteluun osallistuneilla rehtoreilla oli mahdollisuus kommentoida analyysia. Kun teoriaohjaava analyysi oli saatettu käsitekarttojen muotoon, rehtorit osallistuivat palauteverstaaseen, missä ryhmäkeskustelujen avulla validoitiin tutkimustuloksia. Tutkimuksen taustafilosofia on fenomenologia: se tutkii rehtoreiden havaintoihin ja kokemuksiin perustuvia käsityksiä tutkimusalueesta. Rehtoreiden käsitykset oman koulunsa osaamisen tasosta perustuivat kokemusperäiseen tunteeseen, joka syntyy oman joukon tuntemisesta. Rehtorit eivät pystyneet järjestelmällisesti selvittämään, millaista osaamista ja osaamisen tarvetta koulussa on. Omaan toimintatapaansa rehtorit liittivät tunneälyn, jonka avulla he kokivat voimaannuttavansa opettajakuntaansa opettajien itsensä ja koko kouluorganisaation kehittämisen suuntaan. Tutkimukseen osallistuneilla kouluilla ei ollut kirjoitettuja kehittämis-suunnitelmia ja -tavoitteita, mutta rehtorit sanoivat sellaisten olevan selvillä heillä itsellään. Rehtorit totesivat, että opettajien täydennyskouluttautuminen on lähinnä opettajien omista motivaatioista lähtöisin eikä se yksittäisenä tapahtumana kehitä koulun kollektiivista osaamista ja oppivan organisaation syntymistä. Varsinaisia toimenpiteitä oppivan organisaation kehittämiseksi ei tehty. Rehtorit kuitenkin katsoivat pedagogisen hyvinvoinnin kokemuksen kehittyvän koulussa. Rehtoreiden käsitysten mukaan esimiehen tuki sekä osaamisen kokemus vahvistavat hallinnan tunnetta, joka toimii hyvinvoinnin kokemuksen lähtökohtana. Pedagogisen hyvinvoinnin kokemukseen liittyy turvallinen ja avoin toimintakulttuuri. Rehtorit kuvailivat toimivansa eri opettajien kanssa eri tavoin. Rehtoreiden mukaan osaaminen, hallinnan tunne ja pedagoginen hyvinvointi muodostavat kolmikannan, mikä noudattaa myös aiempia DCS-teoriaan pohjautuvia tutkimustuloksia hallinnan tunteen ja hyvinvoinnin yhteydestä.

Influence of surface functionalization on the behavior of silica nanoparticles in biological systems

Personalized nanomedicine has been shown to provide advantages over traditional clinical imaging, diagnosis, and conventional medical treatment. Using nanoparticles can enhance and clarify the clinical targeting and imaging, and lead them exactly to the place in the body that is the goal of treatment. At the same time, one can reduce the side effects that usually occur in the parts of the body that are not targets for treatment. Nanoparticles are of a size that can penetrate into cells. Their surface functionalization offers a way to increase their sensitivity when detecting target molecules. In addition, it increases the potential for flexibility in particle design, their therapeutic function, and variation possibilities in diagnostics. Mesoporous nanoparticles of amorphous silica have attractive physical and chemical characteristics such as particle morphology, controllable pore size, and high surface area and pore volume. Additionally, the surface functionalization of silica nanoparticles is relatively straightforward, which enables optimization of the interaction between the particles and the biological system. The main goal of this study was to prepare traceable and targetable silica nanoparticles for medical applications with a special focus on particle dispersion stability, biocompatibility, and targeting capabilities. Nanoparticle properties are highly particle-size dependent and a good dispersion stability is a prerequisite for active therapeutic and diagnostic agents. In the study it was shown that traceable streptavidin-conjugated silica nanoparticles which exhibit a good dispersibility could be obtained by the suitable choice of a proper surface functionalization route. Theranostic nanoparticles should exhibit sufficient hydrolytic stability to effectively carry the medicine to the target cells after which they should disintegrate and dissolve. Furthermore, the surface groups should stay at the particle surface until the particle has been internalized by the cell in order to optimize cell specificity. Model particles with fluorescently-labeled regions were tested in vitro using light microscopy and image processing technology, which allowed a detailed study of the disintegration and dissolution process. The study showed that nanoparticles degrade more slowly outside, as compared to inside the cell. The main advantage of theranostic agents is their successful targeting in vitro and in vivo. Non-porous nanoparticles using monoclonal antibodies as guiding ligands were tested in vitro in order to follow their targeting ability and internalization. In addition to the targeting that was found successful, a specific internalization route for the particles could be detected. In the last part of the study, the objective was to clarify the feasibility of traceable mesoporous silica nanoparticles, loaded with a hydrophobic cancer drug, being applied for targeted drug delivery in vitro and in vivo. Particles were provided with a small molecular targeting ligand. In the study a significantly higher therapeutic effect could be achieved with nanoparticles compared to free drug. The nanoparticles were biocompatible and stayed in the tumor for a longer time than a free medicine did, before being eliminated by renal excretion. Overall, the results showed that mesoporous silica nanoparticles are biocompatible, biodegradable drug carriers and that cell specificity can be achieved both in vitro and in vivo.

Behavior of black liquor nitrogen in combustion : formation of cyanate

The Kraft pulping process is the dominant chemical pulping process in the world. Roughly 195 million metric tons of black liquor are produced annually as a by-product from the Kraft pulping process. Black liquor consists of spent cooking chemicals and dissolved organics from the wood and can contain up to 0.15 wt% nitrogen on dry solids basis. The cooking chemicals from black liquor are recovered in a chemical recovery cycle. Water is evaporated in the first stage of the chemical recovery cycle, so the black liquor has a dry solids content of 65-85% prior to combustion. During combustion of black liquor, a portion of the black liquor nitrogen is volatilized, finally forming N2 or NO. The rest of the nitrogen remains in the char as char nitrogen. During char conversion, fixed carbon is burned off leaving the pulping chemicals as smelt, and the char nitrogen forms mostly smelt nitrogen (cyanate, OCN-). Smelt exits the recovery boiler and is dissolved in water. The cyanate from smelt decomposes in the presence of water, forming NH3, which causes nitrogen emissions from the rest of the chemical recovery cycle. This thesis had two focuses: firstly, to determine how the nitrogen chemistry in the recovery boiler is affected by modification of black liquor; and secondly, to find out what causes cyanate formation during thermal conversion, and which parameters affect cyanate formation and decomposition during thermal conversion of black liquor. The fate of added biosludge nitrogen in chemical recovery was determined in Paper I. The added biosludge increased the nitrogen content of black liquor. At the pulp mill, the added biosludge did not increase the NO formation in the recovery boiler, but instead increased the amount of cyanate in green liquor. The increased cyanate caused more NH3 formation, which increased the NCG boiler’s NO emissions. Laboratory-scale experiments showed an increase in both NO and cyanate formation after biosludge addition. Black liquor can be modified, for example by addition of a solid biomass to increase the energy density of black liquor, or by separation of lignin from black liquor by precipitation. The precipitated lignin can be utilized in the production of green chemicals or as a fuel. In Papers II and III, laboratory-scale experiments were conducted to determine the impact of black liquor modification on NO and cyanate formation. Removal of lignin from black liquor reduced the nitrogen content of the black liquor. In most cases NO and cyanate formation decreased with increasing lignin removal; the exception was NO formation from lignin lean soda liquors. The addition of biomass to black liquor resulted in a higher nitrogen content fuel mixture, due to the higher nitrogen content of biomass compared to black liquor. More NO and cyanate were formed from the fuel mixtures than from pure black liquor. The increased amount of formed cyanate led to the hypothesis that black liquor is catalytically active and converts a portion of the nitrogen in the mixed fuel to cyanate. The mechanism behind cyanate formation during thermal conversion of black liquor was not clear before this thesis. Paper IV studies the cyanate formation of alkali metal loaded fuels during gasification in a CO2 atmosphere. The salts K2CO3, Na2CO3, and K2SO4 all promoted char nitrogen to cyanate conversion during gasification, while KCl and CaCO3 did not. It is now assumed that cyanate is formed when alkali metal carbonate or an active intermediate of alkali metal carbonate (e.g. -CO2K) reacts with the char nitrogen forming cyanate. By testing different fuels (bark, peat, and coal), each of which had a different form of organic nitrogen, it was concluded that the form of organic nitrogen in char also has an impact on cyanate formation. Cyanate can be formed during pyrolysis of black liquor, but at temperatures 900°C or above, the formed cyanate will decompose. Cyanate formation in gasifying conditions with different levels of CO2 in the atmosphere was also studied. Most of the char nitrogen was converted to cyanate during gasification at 800-900°C in 13-50% CO2 in N2, and only 5% of the initial fuel nitrogen was converted to NO during char conversion. The formed smelt cyanate was stable at 800°C 13% CO2, while it decomposed at 900°C 13% CO2. The cyanate decomposition was faster at higher temperatures and in oxygen-containing atmospheres than in an inert atmosphere. The presence of CO2 in oxygencontaining atmospheres slowed down the decomposition of cyanate. This work will provide new information on how modification of black liquor affects the nitrogen chemistry during thermal conversion of black liquor and what causes cyanate formation during thermal conversion of black liquor. The formation and decomposition of cyanate was studied in order to provide new data, which would be useful in modeling of nitrogen chemistry in the recovery boiler.

Functional cellulose microspheres for pharmaceutical applications

Dissolving cellulose is the first main step in preparing novel cellulosicmaterials. Since cellulosic fibres cannot be easily dissolved in water-based solvents, fibres were pretreated with ethanol-acid solution prior to the dissolution. Solubility and changes on the surface of the fibres were studied with microscopy and capillary viscometry. After the treatment, the cellulose fibres were soluble in alkaline urea-water solvent. The nature of this viscous solution was studied rheologically. Cellulose microspheres were prepared by extruding the alkaline cellulose solution through the needle into an acidic medium. By altering the temperature and acidity of the mediumit was possible to adjust the specific surface area and pore sizes of themicrospheres. A typical skin-core structure was found in all samples. Microspheres were oxidised in order to introduce anionic carboxylic acid groups (AGs). Anionic microspheres are more hydrophilic; their water-uptake increased 25 times after oxidation and they could swell almost to their original state (88%) after drying and shrinking. Swelling was studied in simulated physiological environments, corresponding to stomach acid and intestines (pH 1.2-7.4). Oxidised microspheres were used as a drug carriers. They demonstrated a highmass uniformity, which would enable their use for personalised dosing among different patients, including children. The drug was solidified in microspheres in amorphous form. This enhanced solubility and could be used for more challenging drugs with poor solubility. The pores of themicrospheres also remained open after the drug was loaded and they were dried. Regardless of the swelling, the drug was released at a constant rate in all environments.

Korkeasti kuormitetun soodakattilan likaantumisen ja päästöjen vähentäminen

Tässä työssä perehdytään korkeasti kuormitettujen soodakattiloiden tyypillisiin ongelmiin. Ongelmia ovat likaantuminen ja tukkeutuminen sekä liialliset päästöt. Työn teoriaosassa esitetään taustat likaantumiselle ja päästöjen muodostumiselle. Molemmat johtuvat suurelta osin tulipesän huonosta toiminnasta. Soodakattilan ilmajärjestelmä ja mustalipeän ruiskutus vaikuttavat tulipesän toimintaan. Usein tulipesän toimintaa voidaan parantaa ilmajärjestelmän ja lipeänruiskutuksen säätöjä muuttamalla. Suurempi muutos tulipesän toimintaan saadaan uusimalla perinteinen sekundääri-ilmajärjestelmä vertikaali-ilmajärjestelmäksi. Nykyaikainen vertikaali-ilmajärjestelmä sekoittaa savukaasut tehokkaasti ja saa aikaan tasaisemman virtauksen tulipesään. Myös mustalipeän korkea kloori- ja kaliumpitoisuus voivat aiheuttaa lämpöpintojen likaantumista. Oikea nuohointen sijainti on tärkeä tekijä kattilan puhtaana pysymisen kannalta. Työn kokeellisessa osassa selvitetään, kuinka erään eukalyptussellutehtaan korkeasti kuormitetun soodakattilan käytettävyyttä voidaan parantaa ja kapasiteettia nostaa soodakattilan toimintaa virittämällä. Kattilan nykyinen ajomalli ja ongelmat selvitettiin. Tulipesän toimintaa testattiin muuttamalla ilmajakoa primääri-, sekundääri- ja tertiääri-ilman välillä ja muuttamalla sekundääri-ilman syöttöä tulipesään. Testien ja kerätyn tiedon perusteella voitiin päätellä, miten soodakattilaa kannattaa modernisoida kapasiteetin nostamiseksi ja käytettävyyden parantamiseksi. Usein tulipesän toimintaa ja käytettävyyttä voidaan parantaa paljon jo pienilläkin muutostöillä. Kapasiteetin nostaminen vaatii tavallisesti suuremman investoinnin ja pidennetyn vuosihuoltoseisokin.

Vibration analysis of a power take-off line

Gear rattle is a phenomenon that occurs when idling or lightly loaded gears collide due to engine’s torque fluctuations. This behaviour is related to vibration behaviour of the transmission system. Aim of this master’s thesis is to evaluate Adams and Adams/Machinery as a simulation tools for modelling the rattle e ect in a transmission system. A case study of tractor’s power take-o driveline, suspected to be prone to rattle, is performed in this work. Modelling methods used by Adams in this type of study are presented in the theory section while simulation model build with the software during this work is presented in the results. The Machinery toolbox is used to create gears and bearings while other model components are created with standard Adams tool set. Geometries and excitations are exported from other softwares. Results were obtained from multiple variations of a base model. These result sets and literature review suggest that Adams/Machinery may not be the most suitable tool for rattle analysis. While the system behaviour was partially captured, for accurate modelling user-written routines must be used which may be more easily performed with other tools. Further research about this topic is required.

University students’ regulation of learning and text processing – examples from medical and teacher education

The general aim of the thesis was to study university students’ learning from the perspective of regulation of learning and text processing. The data were collected from the two academic disciplines of medical and teacher education, which share the features of highly scheduled study, a multidisciplinary character, a complex relationship between theory and practice and a professional nature. Contemporary information society poses new challenges for learning, as it is not possible to learn all the information needed in a profession during a study programme. Therefore, it is increasingly important to learn how to think and learn independently, how to recognise gaps in and update one’s knowledge and how to deal with the huge amount of constantly changing information. In other words, it is critical to regulate one’s learning and to process text effectively. The thesis comprises five sub-studies that employed cross-sectional, longitudinal and experimental designs and multiple methods, from surveys to eye tracking. Study I examined the connections between students’ study orientations and the ways they regulate their learning. In total, 410 second-, fourth- and sixth-year medical students from two Finnish medical schools participated in the study by completing a questionnaire measuring both general study orientations and regulation strategies. The students were generally deeply oriented towards their studies. However, they regulated their studying externally. Several interesting and theoretically reasonable connections between the variables were found. For instance, self-regulation was positively correlated with deep orientation and achievement orientation and was negatively correlated with non-commitment. However, external regulation was likewise positively correlated with deep orientation and achievement orientation but also with surface orientation and systematic orientation. It is argued that external regulation might function as an effective coping strategy in the cognitively loaded medical curriculum. Study II focused on medical students’ regulation of learning and their conceptions of the learning environment in an innovative medical course where traditional lectures were combined wth problem-based learning (PBL) group work. First-year medical and dental students (N = 153) completed a questionnaire assessing their regulation strategies of learning and views about the PBL group work. The results indicated that external regulation and self-regulation of the learning content were the most typical regulation strategies among the participants. In line with previous studies, self-regulation wasconnected with study success. Strictly organised PBL sessions were not considered as useful as lectures, although the students’ views of the teacher/tutor and the group were mainly positive. Therefore, developers of teaching methods are challenged to think of new solutions that facilitate reflection of one’s learning and that improve the development of self-regulation. In Study III, a person-centred approach to studying regulation strategies was employed, in contrast to the traditional variable-centred approach used in Study I and Study II. The aim of Study III was to identify different regulation strategy profiles among medical students (N = 162) across time and to examine to what extent these profiles predict study success in preclinical studies. Four regulation strategy profiles were identified, and connections with study success were found. Students with the lowest self-regulation and with an increasing lack of regulation performed worse than the other groups. As the person-centred approach enables us to individualise students with diverse regulation patterns, it could be used in supporting student learning and in facilitating the early diagnosis of learning difficulties. In Study IV, 91 student teachers participated in a pre-test/post-test design where they answered open-ended questions about a complex science concept both before and after reading either a traditional, expository science text or a refutational text that prompted the reader to change his/her beliefs according to scientific beliefs about the phenomenon. The student teachers completed a questionnaire concerning their regulation and processing strategies. The results showed that the students’ understanding improved after text reading intervention and that refutational text promoted understanding better than the traditional text. Additionally, regulation and processing strategies were found to be connected with understanding the science phenomenon. A weak trend showed that weaker learners would benefit more from the refutational text. It seems that learners with effective learning strategies are able to pick out the relevant content regardless of the text type, whereas weaker learners might benefit from refutational parts that contrast the most typical misconceptions with scientific views. The purpose of Study V was to use eye tracking to determine how third-year medical studets (n = 39) and internal medicine residents (n = 13) read and solve patient case texts. The results revealed differences between medical students and residents in processing patient case texts; compared to the students, the residents were more accurate in their diagnoses and processed the texts significantly faster and with a lower number of fixations. Different reading patterns were also found. The observed differences between medical students and residents in processing patient case texts could be used in medical education to model expert reasoning and to teach how a good medical text should be constructed. The main findings of the thesis indicate that even among very selected student populations, such as high-achieving medical students or student teachers, there seems to be a lot of variation in regulation strategies of learning and text processing. As these learning strategies are related to successful studying, students enter educational programmes with rather different chances of managing and achieving success. Further, the ways of engaging in learning seldom centre on a single strategy or approach; rather, students seem to combine several strategies to a certain degree. Sometimes, it can be a matter of perspective of which way of learning can be considered best; therefore, the reality of studying in higher education is often more complicated than the simplistic view of self-regulation as a good quality and external regulation as a harmful quality. The beginning of university studies may be stressful for many, as the gap between high school and university studies is huge and those strategies that were adequate during high school might not work as well in higher education. Therefore, it is important to map students’ learning strategies and to encourage them to engage in using high-quality learning strategies from the beginning. Instead of separate courses on learning skills, the integration of these skills into course contents should be considered. Furthermore, learning complex scientific phenomena could be facilitated by paying attention to high-quality learning materials and texts and other support from the learning environment also in the university. Eye tracking seems to have great potential in evaluating performance and growing diagnostic expertise in text processing, although more research using texts as stimulus is needed. Both medical and teacher education programmes and the professions themselves are challenging in terms of their multidisciplinary nature and increasing amounts of information and therefore require good lifelong learning skills during the study period and later in work life.

Effect of loading type on the fatigue strength of symmetric and asymmetric welded joints made of ultra high strength steel

In this study, finite element analyses and experimental tests are carried out in order to investigate the effect of loading type and symmetry on the fatigue strength of three different non-load carrying welded joints. The current codes and recommendations do not give explicit instructions how to consider degree of bending in loading and the effect of symmetry in the fatigue assessment of welded joints. The fatigue assessment is done by using effective notch stress method and linear elastic fracture mechanics. Transverse attachment and cover plate joints are analyzed by using 2D plane strain element models in FEMAP/NxNastran and Franc2D software and longitudinal gusset case is analyzed by using solid element models in Abaqus and Abaqus/XFEM software. By means of the evaluated effective notch stress range and stress intensity factor range, the nominal fatigue strength is assessed. Experimental tests consist of the fatigue tests of transverse attachment joints with total amount of 12 specimens. In the tests, the effect of both loading type and symmetry on the fatigue strength is studied. Finite element analyses showed that the fatigue strength of asymmetric joint is higher in tensile loading and the fatigue strength of symmetric joint is higher in bending loading in terms of nominal and hot spot stress methods. Linear elastic fracture mechanics indicated that bending reduces stress intensity factors when the crack size is relatively large since the normal stress decreases at the crack tip due to the stress gradient. Under tensile loading, experimental tests corresponded with finite element analyzes. Still, the fatigue tested joints subjected to bending showed the bending increased the fatigue strength of non-load carrying welded joints and the fatigue test results did not fully agree with the fatigue assessment. According to the results, it can be concluded that in tensile loading, the symmetry of joint distinctly affects on the fatigue strength. The fatigue life assessment of bending loaded joints is challenging since it depends on whether the crack initiation or propagation is predominant.