Treatment of oily wastewater by ultrafiltration: The effect of different operating and solution conditions

In many industries, such as petroleum production, and the petrochemical, metal, food and cosmetics industries, wastewaters containing an emulsion of oil in water are often produced. The emulsions consist of water (up to 90%), oils (mineral, animal, vegetable and synthetic), surfactants and other contaminates. In view of its toxic nature and its deleterious effects on the surrounding environment (soil, water) such wastewater needs to be treated before release into natural water ways. Membrane-based processes have successfully been applied in industrial applications and are considered as possible candidates for the treatment of oily wastewaters. Easy operation, lower cost, and in some cases, the ability to reduce contaminants below existing pollution limits are the main advantages of these systems. The main drawback of membranes is flux decline due tofouling and concentration polarisation. The complexity of oil-containing systems demands complementary studies on issues related to the mitigation of fouling and concentration polarisation in membranebased ultrafiltration. In this thesis the effect of different operating conditions (factors) on ultrafiltration of oily water is studied. Important factors are normally correlated and, therefore, their effect should be studied simultaneously. This work uses a novel approach to study different operating conditions, like pressure, flow velocity, and temperature, and solution properties, like oil concentration (cutting oil, diesel, kerosene), pH, and salt concentration (CaCl2 and NaCl)) in the ultrafiltration of oily water, simultaneously and in a systematic way using an experimental design approach. A hypothesis is developed to describe the interaction between the oil drops, salt and the membrane surface. The optimum conditions for ultrafiltration and the contribution of each factor in the ultrafiltration of oily water are evaluated. It is found that the effect on permeate flux of the various factors studied strongly depended on the type of oil, the type of membrane and the amount of salts. The thesis demonstrates that a system containing oil is very complex, and that fouling and flux decline can be observed even at very low pressures. This means that only the weak form of the critical flux exists for such systems. The cleaning of the fouled membranes and the influence of different parameters (flow velocity, temperature, time, pressure, and chemical concentration (SDS, NaOH)) were evaluated in this study. It was observed that fouling, and consequently cleaning, behaved differently for the studied membranes. Of the membranes studied, the membrane with the lowest propensity for fouling and the most easily cleaned was the regenerated cellulose membrane (C100H). In order to get more information about the interaction between the membrane and the components of the emulsion, a streaming potential study was performed on the membrane. The experiments were carried out at different pH and oil concentration. It was seen that oily water changed the surface charge of the membrane significantly. The surface charge and the streaming potential during different stages of filtration were measured and analysed being a new method for fouling of oil in this thesis. The surface charge varied in different stages of filtration. It was found that the surface charge of a cleaned membrane was not the same as initially; however, the permeability was equal to that of a virgin membrane. The effect of filtration mode was studied by performing the filtration in both cross-flow and deadend mode. The effect of salt on performance was considered in both studies. It was found that salt decreased the permeate flux even at low concentration. To test the effect of hydrophilicity change, the commercial membranes used in this thesis were modified by grafting (PNIPAAm) on their surfaces. A new technique (corona treatment) was used for this modification. The effect of modification on permeate flux and retention was evaluated. The modified membranes changed their pore size around 33oC resulting in different retention and permeability. The obtained results in this thesis can be applied to optimise the operation of a membrane plant under normal or shock conditions or to modify the process such that it becomes more efficient or effective.

Fatigue analysis of brackets with and without scallop for bridge and other deck structure using effective notch stress.

Due to functional requirement of a structural detail brackets with and without scallop are frequently used in bridges, decks, ships and offshore structure. Scallops are designed to serve as passage way for fluids, to reduce weld length and plate distortions. Moreover, scallops are used to avoid intersection of two or more welds for the fact that there is the presence of inventible inherent initial crack except for full penetrated weld and the formation of multi-axial stress state at the weld intersection. Welding all around the scallop corner increase the possibility of brittle fracture even for the case the bracket is not loaded by primary load. Avoiding of scallop will establish an initial crack in the corner if bracket is welded by fillet welds. If the two weld run pass had crossed, this would have given a 3D residual stress situation. Therefore the presences and absence of scallop necessitates the 3D FEA fatigue resistance of both types of brackets using effective notch stress approach ( ). FEMAP 10.1 with NX NASTRAN was used for the 3D FEA. The first and main objective of this research was to investigate and compare the fatigue resistance of brackets with and without scallop. The secondary goal was the fatigue design of scallops in case they cannot be avoided for some reason. The fatigue resistance for both types of brackets was determined based on approach using 1 mm fictitiously rounded radius based on IIW recommendation. Identical geometrical, boundary and loading conditions were used for the determination and comparison of fatigue resistance of both types of brackets using linear 3D FEA. Moreover the size effect of bracket length was also studied using 2D SHELL element FEA. In the case of brackets with scallop the flange plate weld toe at the corner of the scallop was found to exhibit the highest and made the flange plate weld toe critical for fatigue failure. Whereas weld root and weld toe at the weld intersections were the highly stressed location for brackets without scallop. Thus weld toe for brackets with scallop, and weld root and weld toe for brackets without scallop were found to be the critical area for fatigue failure. Employing identical parameters on both types of brackets, brackets without scallop had the highest except for full penetrated weld. Furthermore the fatigue resistance of brackets without scallop was highly affected by the lack of weld penetration length and it was found out that decreased as the weld penetration was increased. Despite the fact that the very presence of scallop reduces the stiffness and also same time induce stress concentration, based on the 3D FEA it is worth concluding that using scallop provided better fatigue resistance when both types of brackets were fillet welded. However brackets without scallop had the highest fatigue resistance when full penetration weld was used. This thesis also showed that weld toe for brackets with scallop was the only highly stressed area unlike brackets without scallop in which both weld toe and weld root were the critical locations for fatigue failure when different types of boundary conditions were used. Weld throat thickness, plate thickness, scallop radius, lack of weld penetration length, boundary condition and weld quality affected the fatigue resistance of both types of brackets. And as a result, bracket design procedure, especially welding quality and post weld treatment techniques significantly affect the fatigue resistance of both type of brackets.

Generic Life Cycle Cost Model and Cost-effective Solutions

Life cycle costing (LCC) practices are spreading from military and construction sectors to wider area of industries. Suppliers as well as customers are demanding comprehensive cost knowledge that includes all relevant cost elements through the life cycle of products. The problem of total cost visibility is being acknowledged and the performance of suppliers is evaluated not just by low acquisition costs of their products, but by total value provided through the life time of their offerings. The main purpose of this thesis is to provide better understanding of product cost structure to the case company. Moreover, comprehensive theoretical body serves as a guideline or methodology for further LCC process. Research includes the constructive analysis of LCC related concepts and features as well as overview of life cycle support services in manufacturing industry. The case study aims to review the existing LCC practices within the case company and provide suggestions for improvements. It includes identification of most relevant life cycle cost elements, development of cost breakdown structure and generic cost model for data collection. Moreover, certain cost-effective suggestions are provided as well. This research should support decision making processes, assessment of economic viability of products, financial planning, sales and other processes within the case company.

Effective Message Design and Media Mix of Senior Mobile Phone in China

The present research focuses on the study of how to design message and select media in advertising to generate customer’s purchase intention towards senior mobile phone in China. The message design concentrates mainly on message framing and fear appeals study while the media selection method is only based on direct matching. For exploring the main research question, the study utilized qualitative methodology. The data collection consisted of a pre-interview questionnaire, interviews, and three sets of experiments. The experiments were designed to test the selected 18 participants’ responses toward different emotional appeals and message framings. The findings illustrate participants’ understanding of senior mobile phone and their media usage habits. Moreover, positive message framing and emotional appeals in advertising are more effective. Gender differences in responding to emotional appeals were explored as well.

Fatigue study of the fillet weld waving on weld toe and the penetration in the weld root based on the effective notch stress approach

The fatigue failure of structures under fluctuating loads in fillet weld joints raises a demand to determine the parameters related to this type of loading. In this study, the stress distribution in the susceptible area of weld toe and weld root in fillet welded models analyzed by finite element method applying FEMAP software. To avoid the geometrical singularity on the path of analytical stress analysis in the toe and root area of a weld model the effective notch stress approach applied by which a proper fictitious rounding that mostly depend on the material of structure is applied. The models with different weld toe waving width and radius are analyzed while the flank angle of weld varied in 45 and 30 degrees. The processed results shows that the waving compare to the straight weld toe makes differences in the value of stress and consequently the stress concentration factor between the tip and depth of the waves in the weld toe which helps to protect the crack of propagation and gives enough time and tools to be informed of the crack initiation in the structure during the periodical observation of structure. In the weld root study the analyses among the models with the welding penetration percentage from non-penetration to the full-penetration shows a slightly increase in the root area stress value which comparing with the stiffening effect of penetration conclude that the half-penetration can make an optimization between the stress increase and stiffening effect of deep penetration.

Acidic dissolution of iron oxides and regeneration of a ceramic filter medium

The dewatering of iron ore concentrates requires large capacity in addition to producing a cake with low moisture content. Such large processes are commonly energy intensive and means to lower the specific energy consumption are needed. Ceramic capillary action disc filters incorporate a novel filter medium enabling the harnessing of capillary action, which results in decreased energy consumption in comparison to traditional filtration technologies. As another benefit, the filter medium is mechanically and chemically more durable than, for example, filter cloths and can, thus, withstand harsh operating conditions and possible regeneration better than other types of filter media. In iron ore dewatering, the regeneration of the filter medium is done through a combination of several techniques: (1) backwashing, (2) ultrasonic cleaning, and (3) acid regeneration. Although it is commonly acknowledged that the filter medium is affected by slurry particles and extraneous compounds, published research, especially in the field of dewatering of mineral concentrates, is scarce. Whereas the regenerative effect of backwashing and ultrasound are more or less mechanical, regeneration with acids is based on chemistry. The chemistry behind the acid regeneration is, naturally, dissolution. The dissolution of iron oxide particles has been extensively studied over several decades but those studies may not necessarily be directly applicable in the regeneration of the filter medium which has undergone interactions with the slurry components. The aim of this thesis was to investigate if free particle dissolution indeed correlates with the regeneration of the filter medium. For this purpose, both free particle dissolution and dissolution of surface adhered particles were studied. The focus was on acidic dissolution of iron oxide particles and on the study of the ceramic filter medium used in the dewatering of iron ore concentrates. The free particle dissolution experiments show that the solubility of synthetic fine grained iron oxide particles in oxalic acid could be explained through linear models accounting for the effects of temperature and acid concentration, whereas the dissolution of a natural magnetite is not so easily explained by such models. In addition, the kinetic experiments performed both support and contradict the work of previous authors: the suitable kinetic model here supports previous research suggesting solid state reduction to be the reaction mechanism of hematite dissolution but the formation of a stable iron oxalate is not supported by the results of this research. Several other dissolution mechanisms have also been suggested for iron oxide dissolution in oxalic acid, indicating that the details of oxalate promoted reductive dissolution are not yet agreed and, in this respect, this research offers added value to the community. The results of the regeneration experiments with the ceramic filter media show that oxalic acid is highly effective in removing iron oxide particles from the surface of the filter medium. The dissolution of those particles did not, however, exhibit the expected behaviour, i.e. complete dissolution. The results of this thesis show that although the regeneration of the ceramic filter medium with acids incorporates the dissolution of slurry particles from the surface of the filter medium, the regeneration cannot be assessed purely based upon free particle dissolution. A steady state, dependent on temperature and on the acid concentration, was observed in the dissolution of particles from the surface even though the limit of solubility of free iron oxide particles had not been reached. Both the regeneration capacity and efficiency, with regards to the removal of iron oxide particles, was found to be temperature dependent, but was not affected by the acid concentration. This observation further suggests that the removal of the surface adhered particles does not follow the dissolution of free particles, which do exhibit a dependency on the acid concentration. In addition, changes in the permeability and in the pore structure of the filter medium were still observed after the bulk concentration of dissolved iron had reached a steady state. Consequently, the regeneration of the filter medium continued after the dissolution of particles from the surface had ceased. This observation suggests that internal changes take place at the final stages of regeneration. The regeneration process could, in theory, be divided into two, possibly overlapping, stages: (1) dissolution of surface-adhered particles, and (2) dissolution of extraneous compounds from within the pore structure. In addition to the fundamental knowledge generated during this thesis, tools to assess the effects of parameters on the regeneration of the ceramic filter medium are needed. It has become clear that the same tools used to estimate the dissolution of free particles cannot be used to estimate the regeneration of a filter medium unless only a robust characterisation of the order of regeneration efficiency is needed.

Effective Social Intranet. Case: Mobile Routing Business Unit, Tellabs

The purpose of this thesis is to examine what the normative, effective social Intranet solution is for Tellabs Mobile Routing business unit in terms of sharing knowledge more openly and effectively, fostering innovation, and improving team spirit and positive employee experience. Additionally, these aspects are researched from the intra- and inter-organizational points of view. The research is based on previous literature and empirical interviews. Based on these two items, an eight-fold recommendation proposal was created to change the current Intranet to become an effective social Intranet.

Feasibility study of submerged membrane bioreactor (MBR) as an alternative to conventional activated sludge process (CASP) for municipal wastewater treatment: A pilot scale study

The conventional activated sludge processes (CAS) for the treatment of municipal wastewater are going to be outdated gradually due to more stringent environmental protection laws and regulations. The Membrane bioreactors (MBRs) are the most promising modern technology widely accepted in the world of wastewater treatment due to their highly pronounced features such as high quality effluent, less foot print and working under high MLSS concentration. This research project was carried out to investigate the feasibility and effectiveness of MBR technology compare to the CAS process based on the scientific facts and results. The pilot scale MBR pilot plant was run for more than 150 days and the analysis results were evaluated. The prime focus of the project was to evaluate the correlation of permeate flux under different operating MLSS concentrations. The permeate flux was found almost constant regardless of variations in MLSS concentrations. The removal of micropollutant such as heavy metals, PCPPs, PFCs, steroidal hormones was also studied. The micropollutant removal performance of MBR process was found relatively effective than CAS process. Furthermore, the compatibility of submerged membranes within the bioreactor had truly reduced the process footprint.

Steps towards more effective antitrust system in EU – The Damages Directive’s effect on victim’s right to compensation for antitrust harm

Kaikkien kansalaisten ja yritysten, jotka kärsivät vahinkoa Euroopan Unionin kilpailusääntöjen (SEUT 101 ja 102 artiklan) rikkomisen vuoksi, on voitava vaatia korvauksia vahingon aiheuttaneelta osapuolelta. Euroopan unionin tuomioistuin on ratkaisuillaan Courage ja Manfredi vahvistanut vahinkoa kärsineen oikeuden saada korvausta kärsimästään vahingosta. Suomessa kilpailuoikeudellista vahingonkorvausta koskeva oikeuskäytäntö on ollut vähäistä, vaikkakin viime aikoina on annettu muutama merkittävä vahingonkorvausratkaisu, näistä kenties tunnetuimpana asvalttikartelliratkaisu. Kilpailuoikeuden rikkomisesta vahinkoa kärsineet saavat kuitenkin vain harvoin korvausta kärsimästään vahingosta, mikä on ollut seurausta erilaisista lainsäädännöllisistä ja menettelyistä johtuvista esteistä jäsenvaltioiden säännöissä. Komission pitkään kestänyt lainsäädäntöhanke EU:n kilpailuoikeuden täytäntöönpanojärjestelmän selkeyttämiseksi päättyi marraskuussa 2014, kun Euroopan parlamentin ja neuvoston direktiivi tietyistä säännöistä, joita sovelletaan jäsenvaltioiden ja Euroopan unionin kilpailuoikeuden rikkomisen johdosta kansallisen lainsäädännön nojalla nostettuihin vahingonkorvauskanteisiin (2014/104/ EU) hyväksyttiin. Direktiivi julkaistiin Euroopan unionin virallisessa lehdessä 5. joulukuuta 2014, ja jäsenvaltioilla on 27.12.2016 asti aikaa implementoida direktiivi osaksi kansallista lainsäädäntöä. Direktiivin tavoitteena on EU:n kilpailusääntöjen tehokas täytäntöönpano sekä kilpailuoikeuden julkisoikeudellisen ja yksityisoikeudellisen täytäntöönpanon selkeyttäminen. Lisäksi direktiivi pyrkii varmistamaan, että vahingonkärsijät voivat saada täyden korvauksen kärsimästään vahingosta, sekä poistamaan esteitä ja pienentämään kustannuksia vahingon todistamisessa, samalla harmonisoiden eri jäsenmaissa toimivien yritysten oikeussuojan tasoa. Tarkastelen pro gradu –tutkielmassani kilpailuoikeudellisen vahingonkorvauksen kehitystä sekä uuden EU:n vahingonkorvausdirektiivin vaikutuksia erityisesti vahingonkärsijän näkökulmasta, eli sitä kuinka direktiivi vaikuttaa vahingonkärsijän mahdollisuuteen saada korvausta kärsimästään vahingosta, joka johtuu EU:n kilpailusääntöjen rikkomisesta. Lisäksi tarkastelen lyhyesti direktiivin tuomia muutoksia Suomen lainsäädäntöön. Tutkielmani loppupäätelmä on, että vaikka vahingonkorvausdirektiivi ei täydellisesti paranna vahingonkärsijän asemaa, se selkeyttää monella tavalla kilpailuoikeudellisten vahingonkorvauskanteiden nykyistä tilaa, ja saattaa tietyssä määrin rohkaista vahingonkärsijiä hakemaan korvausta kärsimästään vahingosta.

Opportunity Analysis and Category Management as a Base for Effective Indirect Sourcing

Hankintojen johtamisen kirjallisuus korostaa tehokkaan hankinnan olevan käypä keino tehostaa organisaation tulosta kokonaisvaltaisesti. Myös kasvava tietoisuus erityisesti epäsuorista hankintamenetelmistä ja työkaluista toimivat kannustimina tälle tutkimukselle. Tämän Pro Gradu -tutkimuksen päätarkoituksena on rakentaa kokonaisvaltainen ymmärrys epäsuorasta hankinnasta sekä löytää keinoja sen tehostamiseksi. Tutkimuksen tavoitteena on selvittää, miten globaali, monikansal- linen organisaatio voi parantaa kannattavuuttaan epäsuorissa hankinnoissa, sekä mitkä tekijät hankintastrategiassa vaikuttavat siihen. Tutkimus toteutettiin yksittäisenä tapaustutkimuksena suuren globaalin, monikan- sallisen yrityksen työntekijän näkökulmasta, Pääosa datasta pohjautuu vuonna 2015 toteutettuun Opportunity -analyysi projektiin, joka toteutettiin yhteistyössä ulkoisen konsulttifirman kanssa. Osa datasta pohjautuu puolistrukturoituihin haas- tatteluihin organisaation hankintajohtajan kanssa. Datan keruussa hyödynnettiin lisäksi henkilökohtaista havainnointia ja sekundääristä aineistoa organisaatiosta. Tämä Pro Gradu tutkimus on toteutettu kvalitatiivisella otteella, sisältäen joitakin kvantitatiivisia metodin piirteitä.