Modeling dynamic behavior in tilting pad gas journal bearings

Thisresearch deals with the dynamic modeling of gas lubricated tilting pad journal bearings provided with spring supported pads, including experimental verification of the computation. On the basis of a mathematical model of a film bearing, a computer program has been developed, which can be used for the simulation of a special type of tilting pad gas journal bearing supported by a rotary spring under different loading conditions time dependently (transient running conditions due to geometry variations in time externally imposed). On the basis of literature, different transformations have been used in the model to achieve simpler calculation. The numerical simulation is used to solve a non-stationary case of a gasfilm. The simulation results were compared with literature results in a stationary case (steady running conditions) and they were found to be equal. In addition to this, comparisons were made with a number of stationary and non-stationary bearing tests, which were performed at Lappeenranta University of Technology using bearings designed with the simulation program. A study was also made using numerical simulation and literature to establish the influence of the different bearing parameters on the stability of the bearing. Comparison work was done with literature on tilting pad gas bearings. This bearing type is rarely used. One literature reference has studied the same bearing type as that used in LUT. A new design of tilting pad gas bearing is introduced. It is based on a stainless steel body and electron beam welding of the bearing parts. It has good operation characteristics and is easier to tune and faster to manufacture than traditional constructions. It is also suitable for large serial production.

Dynamic analysis of belt-drives using the absolute nodal coordinate formulation

Belt-drive systems have been and still are the most commonly used power transmission form in various applications of different scale and use. The peculiar features of the dynamics of the belt-drives include highly nonlinear deformation,large rigid body motion, a dynamical contact through a dry friction interface between the belt and pulleys with sticking and slipping zones, cyclic tension of the belt during the operation and creeping of the belt against the pulleys. The life of the belt-drive is critically related on these features, and therefore, amodel which can be used to study the correlations between the initial values and the responses of the belt-drives is a valuable source of information for the development process of the belt-drives. Traditionally, the finite element models of the belt-drives consist of a large number of elements thatmay lead to computational inefficiency. In this research, the beneficial features of the absolute nodal coordinate formulation are utilized in the modeling of the belt-drives in order to fulfill the following requirements for the successful and efficient analysis of the belt-drive systems: the exact modeling of the rigid body inertia during an arbitrary rigid body motion, the consideration of theeffect of the shear deformation, the exact description of the highly nonlinear deformations and a simple and realistic description of the contact. The use of distributed contact forces and high order beam and plate elements based on the absolute nodal coordinate formulation are applied to the modeling of the belt-drives in two- and three-dimensional cases. According to the numerical results, a realistic behavior of the belt-drives can be obtained with a significantly smaller number of elements and degrees of freedom in comparison to the previously published finite element models of belt-drives. The results of theexamples demonstrate the functionality and suitability of the absolute nodal coordinate formulation for the computationally efficient and realistic modeling ofbelt-drives. This study also introduces an approach to avoid the problems related to the use of the continuum mechanics approach in the definition of elastic forces on the absolute nodal coordinate formulation. This approach is applied to a new computationally efficient two-dimensional shear deformable beam element based on the absolute nodal coordinate formulation. The proposed beam element uses a linear displacement field neglecting higher-order terms and a reduced number of nodal coordinates, which leads to fewer degrees of freedom in a finite element.

Dynamic application development in Symbian OS

Diplomityössä tutkitaan, kuinka Symbian-sovelluskehitystä voitaisiin tehostaa. Työssä esitellään Symbian-käyttöjärjestelmä, sekä pohditaan haasteita ja rajoitteita joita Symbian sovelluskehityksessä kohdataan. Myöskin jo olemassa olevia kehitystapoja pohditaan työn tavoitteen kannalta. Symbian-sovelluskehityksessä tehdään toistuvasti samoja asioita. Koska Symbian on avoin käyttöjärjestelmä, sovelluskehittäjiä on paljon. Tehokkaamman kehitystavan löytäminen säästäisi paljon resursseja. Tällä hetkellä perinteiset ohjelmointitavat näyttävät olevan suosituin tapa kehittää sovelluksia. Kuitenkin on jo olemassa useita ratkaisuja, jotka pyrkivät tehostamaan sovelluskehitystä, mikä todistaa tarpeen kehittää tehokkuutta. Työssä toteutettu systeemi ajaa Symbian sovelluksia XML-määrityksen pohjalta. Kun käytetään XML-määritystä C++-koodin sijasta, sovelluskehitys muuttuu. Näiden muutosten täytyy kuitenkin olla myönteisiä, eivätkä ne saa haitata ohjelmiston laatua tai käytettävyyttä.

Dynamic Capabilities and Real Options

Tutkielman tavoitteena oli selvittää dynaamisten kyvykkyyksien teorian kehittymistä ja nykytilaa. Työssä tarkastellaan myös mahdollisuuksia yhdistää reaalioptioajattelua ja dynaamisten kyvykkyyksien teoriaa. Tutkielma on toteutettu teoreettisena kirjallisuuskatsauksena. Dynaamisten kyvykkyyksien teorian mukaan muuttuvassa toimintaympäristössä yritysten kilpailuetu perustuu kykyyn rakentaa, yhdistää ja muokata resursseja ja kyvykkyyksiä. Yritysten täytyy pystyä löytämään, sulauttamaan ja muuntamaan tietoa voidakseen tunnistaa uusia mahdollisuuksia ja pystyäkseen reagoimaan niihin. Tutkielma tuo esille uusia yhteyksiä dynaamisten kyvykkyyksien teorian ja yritysten käyttäytymisen välillä. Reaalioptioajattelu auttaa tunnistamaan yrityksen rajojen määrittämiseen vaikuttavia tekijöitä. Työssä tehdään ehdotuksia dynaamisten kyvykkyyksien teorian jatkotutkimusta varten.

The Dynamic Customer Portfolio Method in Customer Relationship Management

Tutkielman tavoitteena on määritellä keskeiset ja sopivat asiakasportfoliomallit ja asiakasmatriisit asiakassuhteen määrittämiseen. Tutkimus keskittyy asiakassuhteen arvottamiseen ja avainasiakkaiden määrittämiseen kohdeyrityksessä. Keskeisimmät ja sopivimmat asiakasportfliomallit huomioidaan asiakkaiden arvioinnissa. Tutkielman teoriaosassa esitellään tunnetuimmat ja käytetyimmät asiakasportfoliomallit ja matriisit alan kirjallisuuden perusteella. Tämän lisäksi asiakasportfoliomalleihin yhdistetään näkökulmia suhdemarkkinoinnin, asiakkuuksien johtamisen ja tuoteportfolioiden teorioista. Keskeisimmät kirjallisuuden lähteet ovat johtamisen ja markkinoinnin alalta. Tutkielman empiriaosassa esitellään kohdeyritys ja sen tämän hetkinen asiakassuhteiden johtamiskäytäntö. Lisäksi tehdään parannusehdotuksia kohdeyrityksen nykyiseen asiakassuhteiden arvottamismenetelmään jotta asiakassuhteiden arvon laskeminen vastaisi mahdollisimman hyvin kohdeyrityksen nykyisiä tarpeita. Asiakassuhteen arvon määrittämiseksi käytetään myös fokusryhmähaastattelua. Avainasiakkaat määritellään ja tilannetta havainnollistetaan sijoittamalla avainasiakkaat asiakasportfolioon.

Partnering in the Dynamic Environment: The Role of Trust in Asymmetric Technology Partnership Formation

The purpose of this study was to increase the understanding of the role and nature of trust in asymmetric technology partnership formation. In the knowledge-based "learning race" knowledge is considered as a primary source for competitive advantage. In the emerging ICT sector the high pace of technological change, the convergence of technologies and industries as well as the increasing complexity and uncertainty have forced even the largest players to seek cooperation for complementary knowledge and capabilities. Small technology firms need the complementary resources and legitimacy of the large firms to grow and compete in the global market place. Most of the earlier research indicates, however, that partnerships with asymmetric size, managerial resources and cultures have failed. A basic assumption supported by earlier research was that trust is a critical factor in asymmetric technology partnership formation. Asymmetric technology partnership formation is a dynamic and multi-dimensional process, and consequently a holistic research approach was selected. Research issue was approached from different levels: the individual decision-maker, the firm and the relationship between the parties. Also the impact of the dynamic environment and technology content was analyzed. A multitheoretical approach and a qualitative research method with in-depth interviews in five large ICT companies and eight small ICT companies enabled a holistic and rich view of the research issue. Study contributes on the scarce understanding on the nature and evolution of trust in asymmetric technology partnership formation. It sheds also light on the specific nature of asymmetric technology partnerships. The partnerships were found to be tentative and the diverse strategic intent of small and large technology firms appeared as a major challenge. The role of the boundary spanner was highlighted as a possibility to match the incompatible organizational cultures. A shared vision was found to be a pre-condition for individual-based fast trust leading to intuitive decision-making and experimentation. The relationships were tentative and they were continuously re-evaluated through the key actors' sense making of the technology content, asymmetry and the dynamic environment. A multi-dimensional conceptualization for trust was created and propositions on the role and nature of trust for further research are given. The purpose of this study was to increase the understanding of the role and nature of trust in asymmetric technology partnership formation. In the knowledge-based "learning race" knowledge is considered as a primary source for competitive advantage. In the emerging ICT sector the high pace of technological change, the convergence of technologies and industries as well as the increasing complexity and uncertainty have forced even the largest players to seek cooperation for complementary knowledge and capabilities. Small technology firms need the complementary resources and legitimacy of the large firms to grow and compete in the global market place. Most of the earlier research indicates, however, that partnerships with asymmetric size, managerial resources and cultures have failed. A basic assumption supported by earlier research was that trust is a critical factor in asymmetric technology partnership formation. Asymmetric technology partnership formation is a dynamic and multi-dimensional process, and consequently a holistic research approach was selected. Research issue was approached from different levels: the individual decision-maker, the firm and the relationship between the parties. Also the impact of the dynamic environment and technology content was analyzed. A multitheoretical approach and a qualitative research method with in-depth interviews in five large ICT companies and eight small ICT companies enabled a holistic and rich view of the research issue. Study contributes on the scarce understanding on the nature and evolution of trust in asymmetric technology partnership formation. It sheds also light on the specific nature of asymmetric technology partnerships. The partnerships were found to be tentative and the diverse strategic intent of small and large technology firms appeared as a major challenge. The role of the boundary spanner was highlighted as a possibility to match the incompatible organizational cultures. A shared vision was found to be a pre-condition for individual-based fast trust leading to intuitive decision-making and experimentation. The relationships were tentative and they were continuously re-evaluated through the key actors' sense making of the technology content, asymmetry and the dynamic environment. A multi-dimensional conceptualization for trust was created and propositions on the role and nature of trust for further research are given.

Flexible Multibody Simulation Approach in the Dynamic Analysis of Bone Strains Activity

The objective of this study is to show that bone strains due to dynamic mechanical loading during physical activity can be analysed using the flexible multibody simulation approach. Strains within the bone tissue play a major role in bone (re)modeling. Based on previous studies, it has been shown that dynamic loading seems to be more important for bone (re)modeling than static loading. The finite element method has been used previously to assess bone strains. However, the finite element method may be limited to static analysis of bone strains due to the expensive computation required for dynamic analysis, especially for a biomechanical system consisting of several bodies. Further, in vivo implementation of strain gauges on the surfaces of bone has been used previously in order to quantify the mechanical loading environment of the skeleton. However, in vivo strain measurement requires invasive methodology, which is challenging and limited to certain regions of superficial bones only, such as the anterior surface of the tibia. In this study, an alternative numerical approach to analyzing in vivo strains, based on the flexible multibody simulation approach, is proposed. In order to investigate the reliability of the proposed approach, three 3-dimensional musculoskeletal models where the right tibia is assumed to be flexible, are used as demonstration examples. The models are employed in a forward dynamics simulation in order to predict the tibial strains during walking on a level exercise. The flexible tibial model is developed using the actual geometry of the subject’s tibia, which is obtained from 3 dimensional reconstruction of Magnetic Resonance Images. Inverse dynamics simulation based on motion capture data obtained from walking at a constant velocity is used to calculate the desired contraction trajectory for each muscle. In the forward dynamics simulation, a proportional derivative servo controller is used to calculate each muscle force required to reproduce the motion, based on the desired muscle contraction trajectory obtained from the inverse dynamics simulation. Experimental measurements are used to verify the models and check the accuracy of the models in replicating the realistic mechanical loading environment measured from the walking test. The predicted strain results by the models show consistency with literature-based in vivo strain measurements. In conclusion, the non-invasive flexible multibody simulation approach may be used as a surrogate for experimental bone strain measurement, and thus be of use in detailed strain estimation of bones in different applications. Consequently, the information obtained from the present approach might be useful in clinical applications, including optimizing implant design and devising exercises to prevent bone fragility, accelerate fracture healing and reduce osteoporotic bone loss.

Validation of plant dynamic model by online and laboratory measurements – a tool to predict online COD loads out of production of mechanical printing papers

COD discharges out of processes have increased in line with elevating brightness demands for mechanical pulp and papers. The share of lignin-like substances in COD discharges is on average 75%. In this thesis, a plant dynamic model was created and validated as a means to predict COD loading and discharges out of a mill. The assays were carried out in one paper mill integrate producing mechanical printing papers. The objective in the modeling of plant dynamics was to predict day averages of COD load and discharges out of mills. This means that online data, like 1) the level of large storage towers of pulp and white water 2) pulp dosages, 3) production rates and 4) internal white water flows and discharges were used to create transients into the balances of solids and white water, referred to as “plant dynamics”. A conversion coefficient was verified between TOC and COD. The conversion coefficient was used for predicting the flows from TOC to COD to the waste water treatment plant. The COD load was modeled with similar uncertainty as in reference TOC sampling. The water balance of waste water treatment was validated by the reference concentration of COD. The difference of COD predictions against references was within the same deviation of TOC-predictions. The modeled yield losses and retention values of TOC in pulping and bleaching processes and the modeled fixing of colloidal TOC to solids between the pulping plant and the aeration basin in the waste water treatment plant were similar to references presented in literature. The valid water balances of the waste water treatment plant and the reduction model of lignin-like substances produced a valid prediction of COD discharges out of the mill. A 30% increase in the release of lignin-like substances in the form of production problems was observed in pulping and bleaching processes. The same increase was observed in COD discharges out of waste water treatment. In the prediction of annual COD discharge, it was noticed that the reduction of lignin has a wide deviation from year to year and from one mill to another. This made it difficult to compare the parameters of COD discharges validated in plant dynamic simulation with another mill producing mechanical printing papers. However, a trend of moving from unbleached towards high-brightness TMP in COD discharges was valid.

Literature review on permanent magnet generators design and dynamic behavior

This paper is a literature review which describes the construction of state of the art of permanent magnet generators and motors constructing and discusses the current and possible application of these machines in industry. Permanent magnet machines are a well-know class of rotating and linear electric machines used for many years in industrial applications. A particular interest for permanent magnet generators is connected with wind mills, which seem to be becoming increasingly popular nowadays. Geared and direct-driven permanent magnet generators are described. A classification of direct-driven permanent magnet generators is given. Design aspects of permanent magnet generators are presented. Permanent magnet generators for wind turbines designs are highlighted. Dynamics and vibration problems of permanent magnet generators covered in literature are presented. The application of the Finite Element Method for mechanical problems solution in the field of permanent magnet generators is discussed.

Dimensioning DC-voltage capacitor for a DC-distribution system and dynamic analysis

Technical analysis of Low Voltage Direct Current (LVDC) distribution systems shows that in LVDC transmission the customer voltage quality is higher. One of the problems in LVDC distribution networks that converters both ends of the DC line are required. Because of the converters produce not pure DC voltage, but some fluctuations as well, the huge electrolytic capacitors are required to reduce voltage distortions in the DC-side. This thesis master’s thesis is focused on calculating required DC-link capacitance for LVDC transmission and estimation of the influence of different parameters on the voltage quality. The goal is to investigate the methods of the DC-link capacitance estimation and location in the transmission line.

Creating dynamic continuous improvement system for Larox Corporation

Today´s organizations must have the ability to react to rapid changes in the market. These rapid changes cause pressure to continuously find new efficient ways to organize work practices. Increased competition requires businesses to become more effective and to pay attention to quality of management and to make people to understand their work's impact on the final result. The fundamentals in continmuois improvement are systematic and agile tackling of indentified individual process constraints and the fact tha nothin finally improves without changes. Successful continuous improvement requires management commitment, education, implementation, measurement, recognition and regeneration. These ingredients form the foundation, both for breakthrough projects and small step ongoing improvement activities. One part of the organization's management system are the quality tools, which provide systematic methodologies for identifying problems, defining their root causes, finding solutions, gathering and sorting of data, supporting decision making and implementing the changes, and many other management tasks. Organizational change management includes processes and tools for managing the people in an organizational level change. These tools include a structured approach, which can be used for effective transition of organizations through change. When combined with the understanding of change management of individuals, these tools provide a framework for managing people in change,

Games in Education and Process Development

The aim of the thesis is to devise a framework for analyzing simulation games, in particular introductory supply chain simulation games which are used in education and process development. The framework is then applied to three case examples which are introductory supply chain simulation games used at Lappeenranta University of Technology. The theoretical part of the thesis studies simulation games in the context of education and training as well as of process management. Simulation games can be seen as learning processes which comprise of briefing, micro cycle, and debriefing which includes observation and reflection as well as conceptualization. The micro cycle, i.e. the game itself, is defined through elements and characteristics. Both briefing and debriefing ought to support the micro cycle. The whole learning process needs to support learning objectives of the simulation game. Based on the analysis of the case simulation games, suggestions on how to boost the debriefing and promote long term effects of the games are made. In addition, a framework is suggested to be used in designing simulation games and characteristics of introductory supply chain simulation games are defined. They are designed for general purposes, are simple and operated manually, are multifunctional interplays, and last about 2.5 4 hours. Participants co operate during a game run and competition arises between different runs or game sessions.

Dynamic interplay between the intermediate filament protein nestin and Cyclin-dependent kinase 5

Cellen har ett s.k. cytoskelett som bl.a. ger stadga åt cellen och deltar i dess form- och rörelsefunktioner. Intermediärfilamenten är en viktig del av cytoskelettet och de har länge varit kända för sina väsentliga roller i att upprätthålla den cellulära organisationen och vävnadernas integritet. På senare år har man insett att intermediärfilamenten har en större funktionell mångsidighet än man tidigare tänkts sig, i och med att en rad olika studier har visat betydelsen av intermediärfilamenten vid olika signaleringprocesser. Dessa proteinnätverk samverkar nämligen med kinaser och andra viktiga signalfaktorer och deltar därmed i cellens signaleringmaskineri. Intermediärfilamentproteinet nestin används ofta som en markör för stamceller men dess fysiologiska funktioner är i stort sett okända. Interaktion mellan nestin och ett signalkomplex bestående av cyklin-beroende kinas 5 (eng. Cyclin-dependent kinase, Cdk5) och dess aktivatorprotein p35 upptäcktes i vårt laboratorium före denna avhandling påbörjades. Därför var syftet med min avhandling att undersöka den funktionella betydelsen av nestin i regleringen av Cdk5/p35 komplexet. Cdk5 är ett multifunktionellt kinas som reglerar både utvecklingen och stressreaktioner i nerver och muskler. Vi visade att nestin skyddar neuronala stamceller under oxidativ stress genom dess förmåga att hämma Cdk5s skadliga aktivitet. Genom att förankra Cdk5/p35 komplexet, reglerar nestin den subcellulära lokaliseringen av Cdk5/p35 och minskar klyvningen av p35 till den mer stabila aktivatorn p25. Vi demonstrerade också aktiveringsmekanismen för Cdk5 under differentiering av muskelceller. Proteinkinas C zeta (PKCzeta) avslöjades ha en förmåga att accelera klyvningen av p35 till p25, och därmed öka aktiviteten hos Cdk5. Nestin kunde genom sin förmåga att reglera Cdk5 signalkomplexet styra muskelcellernas differentiering. Denna doktorsavhandling har på ett avgörande vis ökat förståelsen av de reglerande mekanismer som styr Cdk5 aktivering. Avhandling presenterar nestin och PKCzeta som kritiska faktorer i denna reglering. Vidare innehåller avhandlingen ny information om de cellulära funktionerna hos nestin som vi har visat vara en viktig reglerare av cellernas överlevnad och differentiering.

Methods and Models for Accelerating Dynamic Simulation of Fluid Power Circuits

The objective of this dissertation is to improve the dynamic simulation of fluid power circuits. A fluid power circuit is a typical way to implement power transmission in mobile working machines, e.g. cranes, excavators etc. Dynamic simulation is an essential tool in developing controllability and energy-efficient solutions for mobile machines. Efficient dynamic simulation is the basic requirement for the real-time simulation. In the real-time simulation of fluid power circuits there exist numerical problems due to the software and methods used for modelling and integration. A simulation model of a fluid power circuit is typically created using differential and algebraic equations. Efficient numerical methods are required since differential equations must be solved in real time. Unfortunately, simulation software packages offer only a limited selection of numerical solvers. Numerical problems cause noise to the results, which in many cases leads the simulation run to fail. Mathematically the fluid power circuit models are stiff systems of ordinary differential equations. Numerical solution of the stiff systems can be improved by two alternative approaches. The first is to develop numerical solvers suitable for solving stiff systems. The second is to decrease the model stiffness itself by introducing models and algorithms that either decrease the highest eigenvalues or neglect them by introducing steady-state solutions of the stiff parts of the models. The thesis proposes novel methods using the latter approach. The study aims to develop practical methods usable in dynamic simulation of fluid power circuits using explicit fixed-step integration algorithms. In this thesis, twomechanisms whichmake the systemstiff are studied. These are the pressure drop approaching zero in the turbulent orifice model and the volume approaching zero in the equation of pressure build-up. These are the critical areas to which alternative methods for modelling and numerical simulation are proposed. Generally, in hydraulic power transmission systems the orifice flow is clearly in the turbulent area. The flow becomes laminar as the pressure drop over the orifice approaches zero only in rare situations. These are e.g. when a valve is closed, or an actuator is driven against an end stopper, or external force makes actuator to switch its direction during operation. This means that in terms of accuracy, the description of laminar flow is not necessary. But, unfortunately, when a purely turbulent description of the orifice is used, numerical problems occur when the pressure drop comes close to zero since the first derivative of flow with respect to the pressure drop approaches infinity when the pressure drop approaches zero. Furthermore, the second derivative becomes discontinuous, which causes numerical noise and an infinitely small integration step when a variable step integrator is used. A numerically efficient model for the orifice flow is proposed using a cubic spline function to describe the flow in the laminar and transition areas. Parameters for the cubic spline function are selected such that its first derivative is equal to the first derivative of the pure turbulent orifice flow model in the boundary condition. In the dynamic simulation of fluid power circuits, a tradeoff exists between accuracy and calculation speed. This investigation is made for the two-regime flow orifice model. Especially inside of many types of valves, as well as between them, there exist very small volumes. The integration of pressures in small fluid volumes causes numerical problems in fluid power circuit simulation. Particularly in realtime simulation, these numerical problems are a great weakness. The system stiffness approaches infinity as the fluid volume approaches zero. If fixed step explicit algorithms for solving ordinary differential equations (ODE) are used, the system stability would easily be lost when integrating pressures in small volumes. To solve the problem caused by small fluid volumes, a pseudo-dynamic solver is proposed. Instead of integration of the pressure in a small volume, the pressure is solved as a steady-state pressure created in a separate cascade loop by numerical integration. The hydraulic capacitance V/Be of the parts of the circuit whose pressures are solved by the pseudo-dynamic method should be orders of magnitude smaller than that of those partswhose pressures are integrated. The key advantage of this novel method is that the numerical problems caused by the small volumes are completely avoided. Also, the method is freely applicable regardless of the integration routine applied. The superiority of both above-mentioned methods is that they are suited for use together with the semi-empirical modelling method which necessarily does not require any geometrical data of the valves and actuators to be modelled. In this modelling method, most of the needed component information can be taken from the manufacturer’s nominal graphs. This thesis introduces the methods and shows several numerical examples to demonstrate how the proposed methods improve the dynamic simulation of various hydraulic circuits.