Packet backbone design differences between commercial network and Container Trial System of LTE/SAE

The mobile networks of earlier and current generations, or 2G and 3G networks, provide users voice and packet services with higher transmission rates and good quality over the same core network. When developing the next generation of mobile networks the current quality of services needs to be maintained. This thesis concentrates on the next generation mobile network, especially on the evolution of the packet network part. The new mobile network has requirements for the common packet backbone network, Mobile Packet Backbone Network, which is additionally discussed in this study. The next generation mobile network, called LTE/SAE, is currently under testing. The test system is called Container Trial System. It is a mini sized LTE/SAE site. The LTE/SAE is studied in this thesis concentrating on the evolved packet core, the SAE part of the composition. The empirical part of the study compares the LTE/SAE Container Trial System and commercial network designs and additionally produces documentation for internal personnel and customers. The research is performed by comparing the documentations and specifications of both the Container Trial System and commercial network. Since the LTE commercial network is not yet constructed, the comparison is done theoretically. The purpose is furthermore to find out if there are any design issues that could be done differently in the next version of the Container Trial System.

Dewatering of hard-to-dewater pulps

Nanocellulose has much potential for enhancing the tensile strength of paper but it slows down significantly drainage, restricting its use in industrial scale. Main objective of the work was to find ways to improve the dewatering of nanocellulose-containing papers. The effects of cationic potato starch, microparticle system and filler addition on dewatering and such key properties as formation, tensile strength and air permeance of manufactured paper were studied. Test points had 0, 4 or 8 % CNF and 0, 15 or 30 % PCC content. Based on earlier studies, 25 mg/g starch dosage was added to some test points. Modern microparticle system, consisted of cationic polyacrylamide and amorphous silica, was used in few test points. Dosages for both components were 0.3 and 0.6 mg/g, following the recommendations of the supplier. Also, the influences of CNF and filler on drying behaviour after different stages (drainage, wet pressing and cylinder drying) were estimated. Following trends were observed. Starch does not have unambiguous influence on dewatering. In some cases, it improved drainage slightly but effects on the properties of end product were discovered small. Filler quickened dewatering but large proportions were noticed to be detrimental for the drainage, air permeance and tensile strength. Microparticle system improved drainage notably, especially if CNF dosage was high. In addition, microparticle system increased tensile strength and decreased air permeance. However, its effects on formation were detrimental. Dewatering of nanocellulose-containing furnishes is treatable up to a certain point. In the end, such drainage times that were measured from test points which consisted only of pure kraft pulps are awkward to reach.

Effect of pulps fractionation on formation and strength properties of laboratory hand sheets

The objectives of the work were to study the effect of dewatering time varying on formation properties of papersheets, to determine the role of fines fraction in creation of paper with good formation and strength properties of papersheets, and also to study the effect of charge modification of fibers fractionations on formation properties of handsheets. The paper formation is one of the most important structural properties of paper. This property has effect on physical and optical characteristics of paper. In thi work the effect of formation on tensile strength was determined. The formation properties were analyzed by using the AMBERTEC Beta Formation Tester. The PAM addition as a f;locculant agent did some changes in the formation of paper. Paper sheets were also made from different furnishes of both birch and pine pulps. The fibers particles as a fines have great effect on drainability changes. Fines fraction played important role in papermaking. The two kinds of pulps (pine and birch pulps) were also used in this work for investigation of fines role. As it was expected the fines fraction gave positive effect on paper formation, but when fines fraction was added above initial fines content the formation of paper was deteriorated. The effect of paper formation on tensile strength was also determined. In many cases the poor formation of paper had negative effect on strength properties of paper..

The strategic use of military contractors : American commercial military service providers in Bosnia and Liberia, 1995-2009

Drawing from strategic theory, this study investigates the strategic roles of commercial companies providing military services, frequently referred to as private military companies. Theoretically, the thesis analyzes how states organize its military capabilities in order to be able to wield power within the international system while empirically, it examines the character and role of commercial companies that provide military training services to the United States Government and partner nations. The reason for this rather instrumental and functional, rather than critical, approach is that this work is written within the discipline known as War Studies. Strategic theory is used first to logically organize the empirical findings in two case studies and then to develop an analytical framework with which the strategic roles of companies providing military services can be investigated. The analysis has been conducted using both new and hitherto unknown sources in the shape of interviews as well as previously classified telegrams, but also draws on previous research and other secondary sources. The main findings are that commercial companies have five typical strategic roles: first, they cloak the state by substituting traditional uniformed troops; second, they act as trailblazers by securing US influence in new regions and by breaking new ground by contributing to the build-up of new partners; third, they act as scene setters by preparing the ground for military exit out of a theater of operations or by facilitating inter-operability between foreign militaries and the US military; fourth, they can be used to infiltrate the security structures of foreign countries; fifth and finally, they can be used to provide offensive capabilities by providing either kinetic or cyber warfare effects. Another finding is that military service contracting is an important part of the US strategic culture.

Management of commercial property derived risks in the market context of the Russian Federation

The objective of the thesis is to examine the current state of risk management and to determine an appropriate risk management policy for commercial property derived risks in the Russian branch of a Finnish retail trade company. The employed research methodologies are comparative in-depth interviews and empirical value at risk analysis, including portfolio risk decomposition to determine the inter-currency characteristics. For a multinational retail trade company, the commercial property derived risks open up as a diverse combination of financial and non-financial risks with four distinctive interest groups. The research results indicate that geographical diversification across currency regimes provides diversification benefits. The Russian ruble is the most significant single risk component when considering the net investments outside the euro-zone. Decreasing the Russian ruble and Swedish krona exposures are the most effective methods to reduce translation derived risk. Exchange rate volatility varies over time according to idiosyncratic currency regime characteristics, and cost-effective risk management requires comprehensive analysis of the business environment. Profound and proactive risk management methods are found to be pivotal for companies with cross-border operations in order to succeed among international competitors.

Success factors of commercial open source software projects

Open source and open source software development have been interesting phenomena during the past decade. Traditional business models do not apply with open source, where the actual product is free. However, it is possible to make business with open source, even successfully, but the question is: how? The aim of this study is to find the key factors of successfully making business out of commercial open source software development. The task is achieved by finding the factors that influence open source projects, finding the relation between those factors, and find out why some factors explain the success more than others. The literature review concentrates first on background of open innovation, open source and open source software. Then business models, critical success factors and success measures are examined. Based on existing literature a framework was created. The framework contains categorized success factors that influence software projects in general as well as open source software projects. The main categories of success factors in software business are divided into community management, technology management, project management and market management. In order to find out which of the factors based on the existing literature are the most critical, empirical research was done by conducting unstructured personal interviews. The main finding based on the interviews is that the critical success factors in open source software business do not differ from those in traditional software business or in fact from those in any other business. Some factors in the framework came out in the interviews that can be considered as key factors: establishing and communicating hierarchy (community management), localization (technology management), good license know-how and IPR management (project management), and effective market management (market management). The critical success factors according to the interviewees are not listed in the framework: low price, good product and good business model development.

Key factors in transforming university internationalization into commercial activity in Finland. Case of University of Turku

Globalization, developments in ICT, emergence of knowledge society and other changes have reformed the environment for international higher education during the past few decades. Consequently, higher education sector has moved towards more marketing-oriented system, and universities have started to undertake commercial activities as part of their internationalization. This development has emerged to Finland as well, which forms the basis for this study. The purpose is to examine commercialization in Finnish university landscape and to investigate the ways Finnish university could capitalize its international activities and educational knowledge for export. The research question of the study is: What are the key factors in transforming university internationalization into commercial activity in the Finnish university landscape? The main problem is further divided into three sub-questions: 1) How can a university internationalize; 2) what are the motivational factors behind university internationalization and commercialization; and 3) how can higher education be developed into export services and products? The research was conducted as a qualitative case study of University of Turku. Methods used for gathering and examining data were interviewing and document analysis. Primary data was collected through four individual semi-structured interviews, which were conducted face-to-face. Secondary data that included reports, articles and electronic materials such as university web pages, was used to complement the primary data. The results were analyzed by theming the data into three broader categories of internationalization activities; drivers and motivations and; education export activities. After the data was organized in themes, analysis continued by comparing different parts of data and finding patterns that would explain the phenomenon in Finnish universities. According to the empirical data, University of Turku is currently on the growth state of internationalization with strategies such as internationalization of curriculum, establishment of international research groups, mobility of students and academics, international networking and support services. Commercialization phenomenon is still rather new to the case university, but it has already developed educational products and services for export. The study concludes that university internationalization cannot be directly transformed into commercial activities in the Finnish context, but the universities need to be active in actually creating educational products. The key factors found in this study include: 1) the Finnish government policies behind the current hype of export education; 2) the potential and knowledge capacity of universities for exports; 3) need for additional profits; 4) further internationalization through commercial activities; 5) recognizing and exploiting the specific areas of strength and 6) establishing of cooperative partnerships for better products.

Magnesium hydroxide-based peroxide bleaching of high-brightness mechanical pulps

A high final brightness is desired in most paper and board products. This requires bleaching processes that are able to produce high-brightness pulps. Mechanical pulps are widely bleached for high brightness using alkaline hydrogen peroxide with traditional sodium hydroxide and sodium silicate as additives. With high doses however, peroxide bleaching causes high organic loads in the mill effluent and anionic trash carry-over to papermaking. To alleviate the problems that arise from the use of sodium-based additives in peroxide bleaching, interest in the use of alternative magnesium-based chemicals has increased. In this study, a new, technical high-purity magnesium hydroxide-based bleaching additive was evaluated on laboratory-scale, pilot-scale and mill-scale experiments and trials for its ability to produce a high brightness in peroxide bleaching without the known problems of sodium-based chemicals. The key findings of this study include: a high brightening potential of peroxide bleaching using the Mg(OH)2-based additive, significant reductions (40-70%) in all categories of environmental load, and cationic demand lowered by 60-70% in bleached pulp with no loss in strength properties or in sheet bulk. When used in TMP refiner bleaching, the Mg(OH)2-based additive resulted in savings in specific energy consumption and provided a good bleaching response.

The role of network externalities in value creating process of the commercial web service for two-sided international markets

Network externalities and two-sided markets in the context of web services and value creation is not very well discussed topic in academic literature. The explosive rise of the Internet users has created a strong base for many successful web services and pushed many firms towards e-business and online service based business models. Thus the subject of this thesis, the role of network externalities in value creating process of the commer-cial web service for two-sided international markets is very current and interesting topic to examine. The objective of this Master’s Thesis is to advance the study of network externalities from the viewpoint of two-sided markets and network effects as well as describe the value creation & value co-creation process in commercial web service business models. The main proposition suggests that the larger network of customers and the bigger number of users the web service is able to attract, the more value and stronger positive net-work externalities the service is able to create for each customer group. The empirical research of this study was implemented for commercial web service, targeted to Russian consumers and Finnish business users. The findings suggest that the size of the network is highly related to the experi-enced value of the customers and the whole value creation process of commercial web targeted for two-sided international markets varies from the value creation for one-sided or pure domestic markets.

Waste Management in Commercial Activity: State-of-the-Art and the Potential Innovation in the Urban Areas of Hanoi, Vietnam

As the rapid development of the society as well as the lifestyle, the generation of commercial waste is getting more complicated to control. The situation of packaging waste and food waste – the main fractions of commercial waste in different countries in Europe and Asia is analyzed in order to evaluate and suggest necessary improvements for the existing waste management system in the city of Hanoi, Vietnam. From all waste generation sources of the city, a total amount of approximately 4000 tons of mixed waste is transported to the composting facility and the disposal site, which emits a huge amount of 1,6Mt of GHG emission to the environment. Recycling activity is taking place spontaneously by the informal pickers, leads to the difficulty in managing the whole system and uncertainty of the overall data. With a relative calculation, resulting in only approximately 0,17Mt CO2 equivalent emission, incinerator is suggested to be the solution of the problem with overloaded landfill and raising energy demand within the inhabitants.

Map of a part of eastern Asia to show the commercial position of the productive coal fields of Yesso, Japan

Kartta kuuluu A. E. Nordenskiöldin kokoelmaan

Nouvelle carte générale et détaillée de l'Europe offrant le tableau actuel, géographique, politique et commercial de tous ses états, leurs limites respectives, les fleuves, les rivières, les grandes chaînes des montaignes et les principales routes, les divisions et subdivisions de cette partie du monde, depuis le traité de Tilsit : dressées d'après les cartes particulières françaises et étrangères les plus détaillées, les plus nouvelles, les éstimées, avec des changements, des restificatios, et les positions assujéties aux observations astronomiques les plus récentes, déterminées par les académiciens et autres savants

Kartta kuuluu A. E. Nordenskiöldin kokoelmaan

Modification of commercial poly-lactide for extrusion coated food packaging applications

Poly-L-lactide (PLLA) is a widely used sustainable and biodegradable alternative to replace synthetic non-degradable plastic materials in the packaging industry. Conversely, its processing properties are not always optimal, e.g. insufficient melt strength at higher temperatures (necessary in extrusion coating processes). This thesis reports on research to improve properties of commercial PLLA grade (3051D from NatureWorks), to satisfy and extend end-use applications, such as food packaging by blending with modified PLLA. Adjustment of the processability by chain branching of commercial poly-L-lactide initiated by peroxide was evaluated. Several well-defined branched structures with four arms (sPLLA) were synthesized using pentaerythritol as a tetra-functional initiator. Finally, several block copolymers consisting of polyethylene glycol and PLLA (i.e. PEGLA) were produced to obtain a well extruded material with improved heat sealing properties. Reactive extrusion of poly-L-lactide was carried out in the presence of 0.1, 0.3 and 0.5 wt% of various peroxides [tert-butyl-peroxybenzoate (TBPB), 2,5-dimethyl-2,5-(tert-butylperoxy)-hexane (Lupersol 101; LOL1) and benzoyl peroxide (BPO)] at 190C. The peroxide-treated PLLAs showed increased complex viscosity and storage modulus at lower frequencies, indicating the formation of branched/cross linked architectures. The material property changes were dependent on the peroxide, and the used peroxide concentration. Gel fraction analysis showed that the peroxides, afforded different gel contents, and especially 0.5 wt% peroxide, produced both an extremely high molar mass, and a cross linked structure, not perhaps well suited for e.g. further use in a blending step. The thermal behavior was somewhat unexpected as the materials prepared with 0.5 wt% peroxide showed the highest ability for crystallization and cold crystallization, despite substantial cross linking. The peroxide-modified PLLA, i.e. PLLA melt extruded with 0.3 wt% of TBPB and LOL1 and 0.5 wt% BPO was added to linear PLLA in ratios of 5, 15 and 30 wt%. All blends showed increased zero shear viscosity, elastic nature (storage modulus) and shear sensitivity. All blends remained amorphous, though the ability of annealing was improved slightly. Extrusion coating on paperboard was conducted with PLLA, and peroxide-modified PLLA blends (90:10). All blends were processable, but only PLLA with 0.3 wt% of LOL1 afforded a smooth high quality surface with improved line speed. Adhesion levels between fiber and plastic, as well as heat seal performance were marginally reduced compared with pure 3051D. The water vapor transmission measurements (WVTR) of the blends containing LOL1 showed acceptable levels, only slightly lower than for comparable PLLA 3051D. A series of four-arm star-shaped poly-L-lactide (sPLLA) with different branch length was synthesized by ring opening polymerization (ROP) of L-lactide using pentaerythritol as initiator and stannous octoate as catalyst. The star-shaped polymers were further blended with its linear resin and studied for their melt flow and thermal properties. Blends containing 30 wt% of sPLLA with low molecular weight (30 wt%; Mwtotal: 2500 g mol-1 and 15000 g mol-1) showed lower zero shear viscosity and significantly increased shear thinning, while at the same time slightly increased crystallization of the blend. However, the amount of crystallization increased significantly with the higher molecular weight sPLLA, therefore the star-shaped structure may play a role as nucleating agent. PLLA-polyethylene glycol–PLLA triblock copolymers (PEGLA) with different PLLA block length were synthesized and their applicability as blends with linear PLLA (3051D NatureWorks) was investigated with the intention of improving heat-seal and adhesion properties of extrusion-coated paperboard. PLLA-PEG-PLLA was obtained by ring opening polymerization (ROP) of L-lactide using PEG (molecular weight 6000 g mol-1) as an initiator, and stannous octoate as catalyst. The structures of the PEGLAs were characterized by proton nuclear magnetic resonance spectroscopy (1H-NMR). The melt flow and thermal properties of all PEGLAs and their blends were evaluated using dynamic rheology, and differential scanning calorimeter (DSC). All blends containing 30 wt% of PEGLAs showed slightly higher zero shear viscosity, higher shear thinning and increased melt elasticity (based on tan delta). Nevertheless, no significant changes in thermal properties were distinguished. High molecular weight PEGLAs were used in extrusion coating line with 3051D without problems.

Effect of ambient conditions on dimensional stability and stiffness of commercial paperboard and paperboard trays

The objective of this study was to develop laboratory test methods for characterizing the effects of changed moisture content on paperboard trays produced by press-forming process. Influence of moisture on the properties of unconverted paperboard such as bending stiffness, bursting strength, and curling was studied. Paperboard and tray samples were tested after storing in different relative humidity conditions (35, 50, 65, 80 and 95% RH). The effect of PE and PET extrusion coatings on these properties was also studied. It was found that increase in moisture content of paperboard decreases bending and bursting strength, dimensional stability and stiffness of paperboard trays. Such physical and mechanical properties as bending stiffness and curling of paperboard seem to define the stiffness of ready-made trays and their dimensional stability. Paperboards and trays with extruded PE and PET one sided coatings demonstrated higher strength properties but at the same time had lower dimensional stability comparing to uncoated paperboards. Samples with smaller polymer coat weight had better dimensional stability than respective samples with higher coat weight. It was also found that preconditioning of paperboard in lower humidity environment before press-forming could improve dimensional stability and stiffness of ready-made tray.