Direct torque control of permanent magnet synchronous machines - analysis and implementation

Thedirect torque control (DTC) has become an accepted vector control method besidethe current vector control. The DTC was first applied to asynchronous machines,and has later been applied also to synchronous machines. This thesis analyses the application of the DTC to permanent magnet synchronous machines (PMSM). In order to take the full advantage of the DTC, the PMSM has to be properly dimensioned. Therefore the effect of the motor parameters is analysed taking the control principle into account. Based on the analysis, a parameter selection procedure is presented. The analysis and the selection procedure utilize nonlinear optimization methods. The key element of a direct torque controlled drive is the estimation of the stator flux linkage. Different estimation methods - a combination of current and voltage models and improved integration methods - are analysed. The effect of an incorrect measured rotor angle in the current model is analysed andan error detection and compensation method is presented. The dynamic performance of an earlier presented sensorless flux estimation method is made better by improving the dynamic performance of the low-pass filter used and by adapting the correction of the flux linkage to torque changes. A method for the estimation ofthe initial angle of the rotor is presented. The method is based on measuring the inductance of the machine in several directions and fitting the measurements into a model. The model is nonlinear with respect to the rotor angle and therefore a nonlinear least squares optimization method is needed in the procedure. A commonly used current vector control scheme is the minimum current control. In the DTC the stator flux linkage reference is usually kept constant. Achieving the minimum current requires the control of the reference. An on-line method to perform the minimization of the current by controlling the stator flux linkage reference is presented. Also, the control of the reference above the base speed is considered. A new estimation flux linkage is introduced for the estimation of the parameters of the machine model. In order to utilize the flux linkage estimates in off-line parameter estimation, the integration methods are improved. An adaptive correction is used in the same way as in the estimation of the controller stator flux linkage. The presented parameter estimation methods are then used in aself-commissioning scheme. The proposed methods are tested with a laboratory drive, which consists of a commercial inverter hardware with a modified software and several prototype PMSMs.

Discovering New Markets for an Industrial Product – International Market Selection Approach

Tämän tutkielman tavoitteena oli määrittää uuden markkinan valinnan perusteita teolliselle tuotteelle. Tutkielma keskittyi jo tunnettuihin kansainvälisen markkinavalinnan lähestymistapoihin ja pyrki soveltamaan yhtä menetelmää käytäntöön tutkielman empiria osassa case-tutkimuksen avulla. Tutkimusote oli tutkiva, eksploratiivinen ja perustui sekundääri analyysiin. Käytetyt tiedon lähteet olivat suureksi osin sekundäärisiä tuottaen kvalitatiivista tietoa. Kuitenkin haastatteluita suoritettiin myös. Kattava kirjallisuus katsaus tunnetuista teoreettisista lähestymistavoista kansainväliseen markkinavalintaan oli osa tutkielmaa. Kolme tärkeintä lähestymistapaa esiteltiin tarkemmin. Yksi lähestymistavoista, ei-järjestelmällinen, muodosti viitekehyksen tutkielman empiria-osalle. Empiria pyrki soveltamaan yhtä ei-järjestelmällisen lähestymistavan malleista kansainvälisessä paperiteollisuudessa. Tarkoituksena oli tunnistaa kaikkein houkuttelevimmat maat mahdollisille markkinointitoimenpiteille tuotteen yhdellä loppukäyttöalueella. Tutkielmassa päädyttiin käyttämään ilmastollisia olosuhteita, siipikarjan päälukua sekä siipikarjan kasvuprosenttia suodattimina pyrittäessä vähentämään mahdollisten maiden lukumäärää. Tutkielman empiria-osa kärsi selkeästi relevantin tiedon puutteesta. Siten myös tutkielman reliabiliteetti ja validiteetti voidaan jossain määrin kyseenalaistaa.

Huulisuihkun homogeenisuuden vaikutus paperin rakenneominaisuuksiin

Työssä verrattiin perälaatikoilla 1 ja 2 valmistettujen papereiden rakenteellisia ominaisuuksia. Paperin rakenteessa formaatio oli tärkein ominaisuus ja sen jälkeen kuituorientaatio. Näytteiden valintaperusteena pidettiin sitä, että vertailtavilla näytteillä formaatio (pohja) oli paras kyseisellä perälaatikolla ja vetolujuussuhteet olivat samoja. Toinen valintatapa oli verrata samoissa virtausolosuhteissa valmistettuja papereita keskenään. Näytteiden formaatio mitattiin betaradiografialla. Fosforikuvalevystä skannattu kuva analysoitiin kuva-analyysillä. Mittauksen etuna oli suuri erottelukyky, joka mahdollisti monipuolisen tunnuslukujen laskennan. Näistä esimerkkeinä olivat keskihajonta, vinous ja huipukkuus. Lisäksi määritettiin flokkikokojakaumat sekä kone- että poikkisuuntaan. Kuituorientaation määrityksessä paperinäyte revittiin kerroksiin, kerrokset skannattiin ja kuvat analysoitiin kuvankäsittelyohjelmilla. Juova- ja kuituorientaatioanalyysissä määritettiin orientaatiokulma, max/min-arvo ja anisotropia. Virtaviiva-analyysin tunnusluku oli pyörrekoko. Käytettäessä tunnuslukuna variaatiokerrointa formaatio oli parempi perälaatikolla 1 ali- ja yliperällä. Tasaperän läheisyydessä formaatio oli huonompi. Keskihajonta oli pienempi perälaatikolla 1, mutta erot perälaatikoiden välillä tasaantuivat lähellä tasaperää. Flokkikoko oli koko s/v-alueella hieman suurempi perälaatikolla 1. Virtaviiva-analyysin avulla saatiin selville, että perälaatikolla 1 valmistettujen papereiden paikallinen orientaatiovaihtelu ja pintojen toispuoleisuus oli lievempää kuin perälaatikolla 2.

Reuse of information for selection of methods and operating conditions for drying of pharmaceutical materials

Drying is a major step in the manufacturing process in pharmaceutical industries, and the selection of dryer and operating conditions are sometimes a bottleneck. In spite of difficulties, the bottlenecks are taken care of with utmost care due to good manufacturing practices (GMP) and industries' image in the global market. The purpose of this work is to research the use of existing knowledge for the selection of dryer and its operating conditions for drying of pharmaceutical materials with the help of methods like case-based reasoning and decision trees to reduce time and expenditure for research. The work consisted of two major parts as follows: Literature survey on the theories of spray dying, case-based reasoning and decision trees; working part includes data acquisition and testing of the models based on existing and upgraded data. Testing resulted in a combination of two models, case-based reasoning and decision trees, leading to more specific results when compared to conventional methods.

Development of beam and plate finite elements based on the absolute nodal coordinate formulation

The focus of this dissertation is to develop finite elements based on the absolute nodal coordinate formulation. The absolute nodal coordinate formulation is a nonlinear finite element formulation, which is introduced for special requirements in the field of flexible multibody dynamics. In this formulation, a special definition for the rotation of elements is employed to ensure the formulation will not suffer from singularities due to large rotations. The absolute nodal coordinate formulation can be used for analyzing the dynamics of beam, plate and shell type structures. The improvements of the formulation are mainly concentrated towards the description of transverse shear deformation. Additionally, the formulation is verified by using conventional iso-parametric solid finite element and geometrically exact beam theory. Previous claims about especially high eigenfrequencies are studied by introducing beam elements based on the absolute nodal coordinate formulation in the framework of the large rotation vector approach. Additionally, the same high eigenfrequency problem is studied by using constraints for transverse deformation. It was determined that the improvements for shear deformation in the transverse direction lead to clear improvements in computational efficiency. This was especially true when comparative stress must be defined, for example when using elasto-plastic material. Furthermore, the developed plate element can be used to avoid certain numerical problems, such as shear and curvature lockings. In addition, it was shown that when compared to conventional solid elements, or elements based on nonlinear beam theory, elements based on the absolute nodal coordinate formulation do not lead to an especially stiff system for the equations of motion.

On the Application of Beam on Elastic Foundation Theory to the Analysis of Stiffened Plate Strips

The main objective of this thesis is to show that plate strips subjected to transverse line loads can be analysed by using the beam on elastic foundation (BEF) approach. It is shown that the elastic behaviour of both the centre line section of a semi infinite plate supported along two edges, and the free edge of a cantilever plate strip can be accurately predicted by calculations based on the two parameter BEF theory. The transverse bending stiffness of the plate strip forms the foundation. The foundation modulus is shown, mathematically and physically, to be the zero order term of the fourth order differential equation governing the behaviour of BEF, whereas the torsion rigidity of the plate acts like pre tension in the second order term. Direct equivalence is obtained for harmonic line loading by comparing the differential equations of Levy's method (a simply supported plate) with the BEF method. By equating the second and zero order terms of the semi infinite BEF model for each harmonic component, two parameters are obtained for a simply supported plate of width B: the characteristic length, 1/ λ, and the normalized sum, n, being the effect of axial loading and stiffening resulting from the torsion stiffness, nlin. This procedure gives the following result for the first mode when a uniaxial stress field was assumed (ν = 0): 1/λ = √2B/π and nlin = 1. For constant line loading, which is the superimposition of harmonic components, slightly differing foundation parameters are obtained when the maximum deflection and bending moment values of the theoretical plate, with v = 0, and BEF analysis solutions are equated: 1 /λ= 1.47B/π and nlin. = 0.59 for a simply supported plate; and 1/λ = 0.99B/π and nlin = 0.25 for a fixed plate. The BEF parameters of the plate strip with a free edge are determined based solely on finite element analysis (FEA) results: 1/λ = 1.29B/π and nlin. = 0.65, where B is the double width of the cantilever plate strip. The stress biaxial, v > 0, is shown not to affect the values of the BEF parameters significantly the result of the geometric nonlinearity caused by in plane, axial and biaxial loading is studied theoretically by comparing the differential equations of Levy's method with the BEF approach. The BEF model is generalised to take into account the elastic rotation stiffness of the longitudinal edges. Finally, formulae are presented that take into account the effect of Poisson's ratio, and geometric non linearity, on bending behaviour resulting from axial and transverse inplane loading. It is also shown that the BEF parameters of the semi infinite model are valid for linear elastic analysis of a plate strip of finite length. The BEF model was verified by applying it to the analysis of bending stresses caused by misalignments in a laboratory test panel. In summary, it can be concluded that the advantages of the BEF theory are that it is a simple tool, and that it is accurate enough for specific stress analysis of semi infinite and finite plate bending problems.

International research partnerships: establishing partner selection criteria in the university-university context

The main objective of the study was to identify and evaluate criteria for international partner selection in university-university context. This study attempted at promoting better understanding of how universities should proceed in selecting partners for producing joint research publications. Thus, the aim of the study was to gain an understanding of how research collaborations can be developed and how partners can be selected. The choice of a right partner has been identified as a precondition for partnership success. In international research collaborations partnering scientists with different skills and backgrounds bring together complementary knowledge into research projects, which in most cases results in a higher quality output. Therefore, prior to selecting a partner, the set of criteria should be established. This research examined twelve Russian universities with the status of national research university as potential partners for Lappeenranta University of Technology, and selected the most appropriate universities based on established set of criteria. Potential partners’ evaluation was done using secondary sources by tracking partners’ academic success during the period 2005 – 2010. Based on established criteria, the study calculated the partnership index for each university. The results of the research reveal that among twelve examined universities there are four potential partners who have been rather active in publishing scientific articles during 2005 – 2010.

Studies in offset ink setting

The offset printing process is complex and involves the meeting of two essentially complex materials, printing ink and paper, upon which the final product is formed. It can therefore be expected that a multitude of chemical and physical interactions and mechanisms take place at the ink-paper interface. Interactions between ink and paper are of interest to both the papermakers and ink producers, as they wish to achieve better quality in the final product. The objective of this work is to clarify the combined influence of paper coating structure, printing ink and fountain solution on ink setting and the problems related to ink setting. A further aim is to identify the mechanisms that influence ink setting problems, and to be able to counteract them by changing properties of the coating layer or by changing the properties of the ink. The work carried out for this thesis included use of many techniques ranging from standard paper and printability tests to advanced optical techniques for detection of ink filaments during ink levelling. Modern imaging methods were applied for assessment of ink filament remain sizes and distribution of ink components inside pigment coating layers. Gravimetric filtration method and assessment of print rub using Ink-Surface-Interaction-Tester (ISIT) were utilized to study the influence of ink properties on ink setting. The chemical interactions were observed with the help of modified thin layer chromatography and contact angle measurements using both conventional and high speed imaging. The results of the papers in this thesis link the press operational parameters to filament sizes and show the influence of these parameters to filament size distribution. The relative importance between the press operation parameters was shown to vary. The size distribution of filaments is important in predicting the ink setting behaviour, which was highlighted by the dynamic gloss and ink setting studies. Prediction of ink setting behaviour was also further improved by use of separate permeability factors for different ink types in connection to filtration equations. The roles of ink components were studied in connection to ink absorption and mechanism of print rub. Total solids content and ratio of linseed oil to mineral oil were found to determine the degree of print rub on coated papers. Wax addition improved print rub resistance, but would not decrease print rub as much as lowering the total solids content in the ink. Linseed oil was shown to absorb into pigment coating pores by mechanism of adsorption to pore walls, which highlights the need for sufficient pore surface area for improved chromatographic separation of ink components. These results should help press operators, suppliers of printing presses, papermakers and suppliers to papermakers, to better understand the material and operating conditions of the press as it relates to various print quality issues. Even though paper is in competition with electronic media, high quality printed products are still in demand. The results should provide useful information for this segment of the industry.

Feature selection using Fuzzy Entropy measures with Yu's Similarity measure

In this study, feature selection in classification based problems is highlighted. The role of feature selection methods is to select important features by discarding redundant and irrelevant features in the data set, we investigated this case by using fuzzy entropy measures. We developed fuzzy entropy based feature selection method using Yu's similarity and test this using similarity classifier. As the similarity classifier we used Yu's similarity, we tested our similarity on the real world data set which is dermatological data set. By performing feature selection based on fuzzy entropy measures before classification on our data set the empirical results were very promising, the highest classification accuracy of 98.83% was achieved when testing our similarity measure to the data set. The achieved results were then compared with some other results previously obtained using different similarity classifiers, the obtained results show better accuracy than the one achieved before. The used methods helped to reduce the dimensionality of the used data set, to speed up the computation time of a learning algorithm and therefore have simplified the classification task

Use of preclinical and early clinical data for dose selection of a selective estrogen receptor modulator toremifene in treatment of breast cancer

In development of human medicines, it is important to predict early and accurately enough the disease and patient population to be treated as well as the effective and safe dose range of the studied medicine. This is pursued by using preclinical research models, clinical pharmacology and early clinical studies with small sample sizes. When successful, this enables effective development of medicines and reduces unnecessary exposure of healthy subjects and patients to ineffectice or harmfull doses of experimental compounds. Toremifene is a selective estrogen receptor modulator (SERM) used for treatment of breast cancer. Its development was initiated in 1980s when selection of treatment indications and doses were based on research in cell and animal models and on noncomparative clinical studies including small number of patients. Since the early development phase, the treatment indication, the patient population and the dose range were confirmed in large comparative clinical studies in patients. Based on the currently available large and long term clinical study data the aim of this study was to investigate how the early phase studies were able to predict the treatment indication, patient population and the dose range of the SERM. As a conclusion and based on the estrogen receptor mediated mechanism of action early studies were able to predict the treatment indication, target patient population and a dose range to be studied in confirmatory clinical studies. However, comparative clinical studies are needed to optimize dose selection of the SERM in treatment of breast cancer.

The energy efficiency of chilled beam systems in an office building at different climates

Besides the sustaining of healthy and comfortable indoor climate, the air conditioning system should also achieve for energy efficiency. The target indoor climate can be ob-tained with different systems; this study focuses on comparing the energy efficiency of different air conditioning room unit systems in different climates. The calculations are made with dynamic energy simulation software IDA ICE by comparing the indoor cli-mate and energy consumption of an office building with different systems in different climates. The aim of the study is to compare the energy efficiency of chilled beam systems to other common systems: variable air volume, fan coil and radiant ceiling systems. Besides the annual energy consumption also the sustainability of target indoor climate is compared between the simulations. Another aim is to provide conclusions to be used in the product development of the chilled beam systems’ energy efficiency. The adaptable chilled beam system and the radiant ceiling system prove to be energy efficient independent of the climate. The challenge of reliable comparison is that other systems are not able to reach the target indoor climate as well as the others. The complex calculation environment of the simulation software, made assumptions and excluding of the financial aspects complicate comparing the big picture. The results show that the development of the chilled beam systems should concentrate on energy efficient night heating, flexible demand based ventilation and capacity control and possibilities on integrating the best practices with other systems. 

Puomiankkurin uudelleensuunnittelu ja valmistus

Tämän diplomityön tavoitteena on ollut suunnitella uusi öljyntorjunnassa käytettävä puomiankkuri. Nykyisin käytössä olevat ankkurit ovat painavia, paljon tilaa vieviä, jäykkiä rakenteeltaan ja hankalia käyttää. Työn tavoitteena on ollut suunnitella rakenne, jossa muotoilun avulla pyritään korvaamaan ankkurin painoa ja saavuttaa hyvä tunkeutuminen eri pohjalaaduissa. Ankkurin suunnitteluun kuuluu merkittävänä osana materiaalinvalintaprosessi, jonka perusteella materiaaliksi valittiin kulutusteräs. Kulutusteräksen korkea lujuus ja hyvä kulumiskestävyys mahdollistavat ohuemman materiaalin käytön rakenteessa, jonka seurauksena rakenteen painoa saatiin vähennettyä merkittävästi. Ankkurin rakenteen suunnittelussa käytettiin hyväksi nykyisiä ankkurin rakenteita, joiden pohjalta hahmoteltiin eri variaatioita ankkureista. Suunnittelutyössä käytettiin hyväksi tyypillisiä ankkurirakenteita hyvien puolien kannalta, joita pyrittiin toteuttamaan uudessa ankkuri- rakenteessa. Ankkurin suunnittelu toteutettiin järjestelmällisen suunnittelun avulla, jossa ensin laadittiin ankkurille vaatimuslista. Tämän jälkeen laadittiin ankkurille toimintorakenne ja jakaminen osatoimintoihin. Ankkurin rakenteista toteutettiin kaksi eri versiota: sisävesillä ja merialueilla käytettävät ankkurit, joille laadittiin mitoitus. Työssä suunnitellun terävän tunkeutumisosan ja optimaalisen tunkeutumiskulman avulla ankkureiden painoa saatiin huomattavasti alhaisemmaksi, jonka seurauksena ankkurille saatiin kevyempi rakenne ja materiaalikustannukset pienenivät merkittävästi. Uusien ankkurien rakenne on pienemmän koon ja painon ansiosta käyttäjäystävällisempi.

Puomiankkurin uudelleensuunnittelu ja valmistus

Tämän diplomityön tavoitteena on ollut suunnitella uusi öljyntorjunnassa käytettävä puomiankkuri. Nykyisin käytössä olevat ankkurit ovat painavia, paljon tilaa vieviä, jäykkiä rakenteeltaan ja hankalia käyttää. Työn tavoitteena on ollut suunnitella rakenne, jossa muotoilun avulla pyritään korvaamaan ankkurin painoa ja saavuttaa hyvä tunkeutuminen eri pohjalaaduissa. Ankkurin suunnitteluun kuuluu merkittävänä osana materiaalinvalintaprosessi, jonka perusteella materiaaliksi valittiin kulutusteräs. Kulutusteräksen korkea lujuus ja hyvä kulumiskestävyys mahdollistavat ohuemman materiaalin käytön rakenteessa, jonka seurauksena rakenteen painoa saatiin vähennettyä merkittävästi. Ankkurin rakenteen suunnittelussa käytettiin hyväksi nykyisiä ankkurin rakenteita, joiden pohjalta hahmoteltiin eri variaatioita ankkureista. Suunnittelutyössä käytettiin hyväksi tyypillisiä ankkurirakenteita hyvien puolien kannalta, joita pyrittiin toteuttamaan uudessa ankkuri- rakenteessa. Ankkurin suunnittelu toteutettiin järjestelmällisen suunnittelun avulla, jossa ensin laadittiin ankkurille vaatimuslista. Tämän jälkeen laadittiin ankkurille toimintorakenne ja jakaminen osatoimintoihin. Ankkurin rakenteista toteutettiin kaksi eri versiota: sisävesillä ja merialueilla käytettävät ankkurit, joille laadittiin mitoitus. Työssä suunnitellun terävän tunkeutumisosan ja optimaalisen tunkeutumiskulman avulla ankkureiden painoa saatiin huomattavasti alhaisemmaksi, jonka seurauksena ankkurille saatiin kevyempi rakenne ja materiaalikustannukset pienenivät merkittävästi. Uusien ankkurien rakenne on pienemmän koon ja painon ansiosta käyttäjäystävällisempi.