Converter-flux-based current control of voltage source PWM rectifiers - analysis and implementation

Pulsewidth-modulated (PWM) rectifier technology is increasingly used in industrial applications like variable-speed motor drives, since it offers several desired features such as sinusoidal input currents, controllable power factor, bidirectional power flow and high quality DC output voltage. To achieve these features,however, an effective control system with fast and accurate current and DC voltage responses is required. From various control strategies proposed to meet these control objectives, in most cases the commonly known principle of the synchronous-frame current vector control along with some space-vector PWM scheme have been applied. Recently, however, new control approaches analogous to the well-established direct torque control (DTC) method for electrical machines have also emerged to implement a high-performance PWM rectifier. In this thesis the concepts of classical synchronous-frame current control and DTC-based PWM rectifier control are combined and a new converter-flux-based current control (CFCC) scheme is introduced. To achieve sufficient dynamic performance and to ensure a stable operation, the proposed control system is thoroughly analysed and simple rules for the controller design are suggested. Special attention is paid to the estimationof the converter flux, which is the key element of converter-flux-based control. Discrete-time implementation is also discussed. Line-voltage-sensorless reactive reactive power control methods for the L- and LCL-type line filters are presented. For the L-filter an open-loop control law for the d-axis current referenceis proposed. In the case of the LCL-filter the combined open-loop control and feedback control is proposed. The influence of the erroneous filter parameter estimates on the accuracy of the developed control schemes is also discussed. A newzero vector selection rule for suppressing the zero-sequence current in parallel-connected PWM rectifiers is proposed. With this method a truly standalone and independent control of the converter units is allowed and traditional transformer isolation and synchronised-control-based solutions are avoided. The implementation requires only one additional current sensor. The proposed schemes are evaluated by the simulations and laboratory experiments. A satisfactory performance and good agreement between the theory and practice are demonstrated.

Direct torque control of permanent magnet synchronous machines - analysis and implementation

Thedirect torque control (DTC) has become an accepted vector control method besidethe current vector control. The DTC was first applied to asynchronous machines,and has later been applied also to synchronous machines. This thesis analyses the application of the DTC to permanent magnet synchronous machines (PMSM). In order to take the full advantage of the DTC, the PMSM has to be properly dimensioned. Therefore the effect of the motor parameters is analysed taking the control principle into account. Based on the analysis, a parameter selection procedure is presented. The analysis and the selection procedure utilize nonlinear optimization methods. The key element of a direct torque controlled drive is the estimation of the stator flux linkage. Different estimation methods - a combination of current and voltage models and improved integration methods - are analysed. The effect of an incorrect measured rotor angle in the current model is analysed andan error detection and compensation method is presented. The dynamic performance of an earlier presented sensorless flux estimation method is made better by improving the dynamic performance of the low-pass filter used and by adapting the correction of the flux linkage to torque changes. A method for the estimation ofthe initial angle of the rotor is presented. The method is based on measuring the inductance of the machine in several directions and fitting the measurements into a model. The model is nonlinear with respect to the rotor angle and therefore a nonlinear least squares optimization method is needed in the procedure. A commonly used current vector control scheme is the minimum current control. In the DTC the stator flux linkage reference is usually kept constant. Achieving the minimum current requires the control of the reference. An on-line method to perform the minimization of the current by controlling the stator flux linkage reference is presented. Also, the control of the reference above the base speed is considered. A new estimation flux linkage is introduced for the estimation of the parameters of the machine model. In order to utilize the flux linkage estimates in off-line parameter estimation, the integration methods are improved. An adaptive correction is used in the same way as in the estimation of the controller stator flux linkage. The presented parameter estimation methods are then used in aself-commissioning scheme. The proposed methods are tested with a laboratory drive, which consists of a commercial inverter hardware with a modified software and several prototype PMSMs.

Strategy Implementation Bottlenecks: Identification, Analysis and Removal

This thesis investigates the strategy implementation process of enterprices; a process whichhas lacked the academic attentioon compared with a rich strategy formation research trdition. Strategy implementation is viewed as a process ensuring tha the strtegies of an organisation are realised fully and quickly, yet with constant consideration of changing circumstances. The aim of this sudy is to provide a framework for identifying, analysing and removing the strategy implementation bottleneck af an organization and thus for intesifying its strategy process.The study is opened by specifying the concept, tasks and key actors of strategy implementation process; especially arguments for the critical implementation role of the top management are provided. In order to facilitate the analysis nad synthetisation of the core findings of scattered doctrine, six characteristic approaches to strategy implementation phenomenon are identified and compared. The Bottleneck Framework is introduced as an instrument for arranging potential strategy realisation problems, prioritising an organisation's implementation obstacles and focusing the improvement measures accordingly. The SUCCESS Framework is introduced as a mnemonic of the seven critical factors to be taken into account when promoting sttrategy implementation. Both frameworks are empirically tested by applying them to real strategy implementation intesification process in an international, industrial, group-structured case enterprise.

Interfacing Health Care Information Systems Design and Implementation

Terveydenhuollossa käytetään nykyisin informaatioteknologian (IT) mahdollisuuksia parantamaan hoidon laatua, vähentämään hoitoon liittyviä kuluja sekä yksinkertaistamaan ja selkeyttämään laakareiden työnkulkua. Tietojärjestelmät, jotka edustavat jokaisen IT-ratkaisun ydintä, täytyy kehittää täyttämään lukuisia vaatimuksia, ja yksi niistä on kyky integroitua saumattomasti toisten tietojärjestelmien kanssa. Järjestelmäintegraatio on kuitenkin yhä haastava tehtävä, vaikka sita varten on kehitetty useita standardeja. Tässä työssä kuvataan vastakehitetyn lääketieteellisen tietojärjestelmän liittymäratkaisu. Työssä pohditaan vaatimuksia, jotka tällaiselle sovellukselle asetetaan, ja myös tapa, jolla vaatimukset toteutuvat on esitetty. Liittymaratkaisu on jaettu kahteen osaan, tietojärjestelmaliittymään ja "liittymakoneeseen" (interfacing engine). Edellinen on käsittää perustoiminnallisuuden, jota tarvitaan vastaanottamaan ja lähettämään tietoa toisiin järjestelmiin, kun taas jälkimmäinen tarjoaa tuen tuotantoympäristössa käytettäville standardeille. Molempien osien suunnitelu on esitelty perusteellisesti tässä työssä. Ongelma ratkaistiin modulaarisen ja geneerisen suunnittelun avulla. Tämä lähestymistapa osoitetaan työssä kestäväksi ja joustavaksi ratkaisuksi, jota voidaan käyttää tarkastelemaan laajaa valikoimaa liittymäratkaisulle asetettuja vaatimuksia. Lisaksi osoitetaan kuinka tehty ratkaisu voidaan joustavuutensa ansiosta helposti mukauttaa vaatimuksiin, joita ei ole etukäteen tunnistettu, ja siten saavutetaan perusta myös tulevaisuuden tarpeille

Railway Wagon Market Analysis and New Multi-Purpose Wagon Solution for Freight Transports - Finnish Manufacturing Perspective

Rautateillä käytettävät tavaravaunut ovat vanhenemassa hyvin nopeasti; tämä koskee niin Venäjää, Suomea, Ruotsia kuin laajemminkin Eurooppaa. Venäjällä ja Euroopassa on käytössä runsaasti vaunuja, jotka ovat jo ylittäneet niille suositeltavan käyttöiän. Silti niitä käytetään kuljetuksissa, kun näitä korvaavia uusia vaunuja ei ole tarpeeksi saatavilla. Uusimmat vaunut ovat yleensä vaunuja vuokraavien yritysten tai uusien rautatieoperaattorien hankkimia - tämä koskee erityisesti Venäjää, jossa vaunuvuokraus on noussut erittäin suosituksi vaihtoehdoksi. Ennusteissa kerrotaan vaunupulan kasvavan ainakin vuoteen 2010 saakka. Jos rautateiden suosio rahtikuljetusmuotona kasvaa, niin voimistuva vaunukysyntä jatkuu huomattavan paljon pidemmän aikaa. Euroopan ja Venäjän vaunukannan tilanne näkyy myös sitä palvelevan konepajateollisuuden ongelmina - yleisesti ottaen alan eurooppalaiset yritykset ovat heikosti kannattavia ja niiden liikevaihto ei juuri kasva, venäläiset ja ukrainalaiset yritykset ovat olleet samassa tilanteessa, joskin aivan viime vuosina tilanne on osassa kääntynyt paremmaksi. Kun näiden maanosien yritysten liikevaihtoa, voittoa ja omistaja-arvoa verrataan yhdysvaltalaisiin kilpailijoihin, huomataan että jälkimmäisten suoriutuminen on huomattavan paljon parempaa, ja näillä yrityksillä on myös kyky maksaa osinkoja omistajilleen. Tutkimuksen tarkoituksena oli kehittää uuden tyyppinen kuljetusvaunu Suomen, Venäjän sekä mahdollisesti myös Kiinan väliseen liikenteeseen. Vaunutyypin tarkoituksena olisi kyetä toimimaan monikäyttöisenä, niin raaka-aineiden kuin konttienkin kuljetuksessa, tasapainottaen kuljetusmuotojen aiheuttamaa kuljetuspaino-ongelmaa. Kehitystyön pohjana käytimme yli 1000 venäläisen vaunutyypin tietokantaa, josta valitsimme Data Envelopment Analysis -menetelmällä soveliaimmat vaunut kontinkuljetukseen (lähemmin tarkastelimme n. 40 vaunutyyppiä), jättäen mahdollisimman vähän tyhjää tilaa junaan, mutta silti kyeten kantamaan valitun konttilastin. Kun kantokykyongelmia venäläisissä vaunuissa ei useinkaan ole, on vertailu tehtävissä tavarajunan pituuden ja kokonaispainon perusteella. Simuloituamme yhdistettyihin kuljetuksiin soveliasta vaunutyyppiä käytännössä löytyvässä kuljetusverkostossa (esim. raakapuuta Suomeen tai Kiinaan ja kontteja takaisin Venäjän suuntaan), huomasimme lyhemmän vaunupituuden sisältävän kustannusetua, erityisesti raakaainekuljetuksissa, mutta myös rajanylityspaikkojen mahdollisesti vähentyessä. Lyhempi vaunutyyppi on myös joustavampi erilaisten konttipituuksien suhteen (40 jalan kontin käyttö on yleistynyt viime vuosina). Työn lopuksi ehdotamme uuden vaunutyypin tuotantotavaksi verkostomaista lähestymistapaa, jossa osa vaunusta tehtäisiin Suomessa ja osa Venäjällä ja/tai Ukrainassa. Vaunutyypin tulisi olla rekisteröity Venäjälle, sillä silloin sitä voi käyttää Suomen ja Venäjän, kuten myös soveltuvin osin Venäjän ja Kiinan välisessä liikenteessä.

On the Analysis and Control of a Linear Synchronous Servomotor with a Flexible Load

Industry's growing need for higher productivity is placing new demands on mechanisms connected with electrical motors, because these can easily lead to vibration problems due to fast dynamics. Furthermore, the nonlinear effects caused by a motor frequently reduce servo stability, which diminishes the controller's ability to predict and maintain speed. Hence, the flexibility of a mechanism and its control has become an important area of research. The basic approach in control system engineering is to assume that the mechanism connected to a motor is rigid, so that vibrations in the tool mechanism, reel, gripper or any apparatus connected to the motor are not taken into account. This might reduce the ability of the machine system to carry out its assignment and shorten the lifetime of the equipment. Nonetheless, it is usually more important to know how the mechanism, or in other words the load on the motor, behaves. A nonlinear load control method for a permanent magnet linear synchronous motor is developed and implemented in the thesis. The purpose of the controller is to track a flexible load to the desired velocity reference as fast as possible and without awkward oscillations. The control method is based on an adaptive backstepping algorithm with its stability ensured by the Lyapunov stability theorem. As a reference controller for the backstepping method, a hybrid neural controller is introduced in which the linear motor itself is controlled by a conventional PI velocity controller and the vibration of the associated flexible mechanism is suppressed from an outer control loop using a compensation signal from a multilayer perceptron network. To avoid the local minimum problem entailed in neural networks, the initial weights are searched for offline by means of a differential evolution algorithm. The states of a mechanical system for controllers are estimated using the Kalman filter. The theoretical results obtained from the control design are validated with the lumped mass model for a mechanism. Generalization of the mechanism allows the methods derived here to be widely implemented in machine automation. The control algorithms are first designed in a specially introduced nonlinear simulation model and then implemented in the physical linear motor using a DSP (Digital Signal Processor) application. The measurements prove that both controllers are capable of suppressing vibration, but that the backstepping method is superior to others due to its accuracy of response and stability properties.

Power line communication in motor cables of variable-speed electric drives − analysis and

Data transmission between an electric motor and a frequency converter is required in variablespeed electric drives because of sensors installed at the motor. Sensor information can be used for various useful applications to improve the system reliability and its properties. Traditionally, the communication medium is implemented by an additional cabling. However, the costs of the traditional method may be an obstacle to the wider application of data transmission between a motor and a frequency converter. In any case, a power cable is always installed between a motor and a frequency converter for power supply, and hence it may be applied as a communication medium for sensor level data. This thesis considers power line communication (PLC) in inverter-fed motor power cables. The motor cable is studied as a communication channel in the frequency band of 100 kHz−30 MHz. The communication channel and noise characteristics are described. All the individual components included in a variable-speed electric drive are presented in detail. A channel model is developed, and it is verified by measurements. A theoretical channel information capacity analysis is carried out to estimate the opportunities of a communication medium. Suitable communication and forward error correction (FEC) methods are suggested. A general method to implement a broadband and Ethernet-based communication medium between a motor and a frequency converter is proposed. A coupling interface is also developed that allows to install the communication device safely to a three-phase inverter-fed motor power cable. Practical tests are carried out, and the results are analyzed. Possible applications for the proposed method are presented. A speed feedback motor control application is verified in detail by simulations and laboratory tests because of restrictions for the delay in the feedback loop caused by PLC. Other possible applications are discussed at a more general level.

DFM/DFMA(A) – analysis and aspects of applying systematic engineering for a microwave testfixture design

In this paper, manufacturability analysis and collection of design aspects is made for a microwave test-fixture. Aspects of applying systematic design for a microwave test-fixture design and manufacturing are also analysed. Special questionnaires for the component and machining are made in order to enable necessary information to ensure DFM(A) – aspects of the component. The aspects of easy manufacturing for machining the microwave test-fixture are collected. Material selection is discussed and manufacturing stages of prototype manufacturing are presented.

Power Consumption in Carbon Capture and Storage Systems (CCS) and Possibilities to Reduce Power Consumption with Variable Speed Drives

The aim of this master´s thesis is to study which processes increase the auxiliary power consumption in carbon capture and storage processes and if it is possible to reduce the auxiliary power consumption with variable speed drives. Also the cost of carbon capture and storage is studied. Data about auxiliary power consumption in carbon capture is gathered from various studies and estimates made by various research centres. Based on these studies a view is presented how the power auxiliary power consumption is divided between different processes in carbon capture processes. In a literary study, the operation of three basic carbon capture systems is described. Also different methods to transport carbon dioxide and carbon dioxide storage options are described in this section. At the end of the thesis processes that consume most of the auxiliary power are defined and possibilities to reduce the auxiliary power consumption are evaluated. Cost of carbon capture, transport and storage are also evaluated at this point and in the case that the carbon capture and storage systems are fully deployed. According to the results, it can be estimated what are the processes are where variable speed drives can be used and what kind of cost and power consumption reduction could be achieved. Results also show how large a project carbon capture and storage is if it is fully deployed.

Ultrafine grinding of FGD and phosphogypsum with an attrition bead mill and a jet mill : optimisation and modelling of grinding and mill comparison

Fine powders of minerals are used commonly in the paper and paint industry, and for ceramics. Research for utilizing of different waste materials in these applications is environmentally important. In this work, the ultrafine grinding of two waste gypsum materials, namely FGD (Flue Gas Desulphurisation) gypsum and phosphogypsum from a phosphoric acid plant, with the attrition bead mill and with the jet mill has been studied. The ' objective of this research was to test the suitability of the attrition bead mill and of the jet mill to produce gypsum powders with a particle size of a few microns. The grinding conditions were optimised by studying the influences of different operational grinding parameters on the grinding rate and on the energy consumption of the process in order to achieve a product fineness such as that required in the paper industry with as low energy consumption as possible. Based on experimental results, the most influential parameters in the attrition grinding were found to be the bead size, the stirrer type, and the stirring speed. The best conditions, based on the product fineness and specific energy consumption of grinding, for the attrition grinding process is to grind the material with small grinding beads and a high rotational speed of the stirrer. Also, by using some suitable grinding additive, a finer product is achieved with a lower energy consumption. In jet mill grinding the most influential parameters were the feed rate, the volumetric flow rate of the grinding air, and the height of the internal classification tube. The optimised condition for the jet is to grind with a small feed rate and with a large rate of volumetric flow rate of grinding air when the inside tube is low. The finer product with a larger rate of production was achieved with the attrition bead mill than with the jet mill, thus the attrition grinding is better for the ultrafine grinding of gypsum than the jet grinding. Finally the suitability of the population balance model for simulation of grinding processes has been studied with different S , B , and C functions. A new S function for the modelling of an attrition mill and a new C function for the modelling of a jet mill were developed. The suitability of the selected models with the developed grinding functions was tested by curve fitting the particle size distributions of the grinding products and then comparing the fitted size distributions to the measured particle sizes. According to the simulation results, the models are suitable for the estimation and simulation of the studied grinding processes.

Statistical Analysis and Numerics of Heat Exchanger Models

The identifiability of the parameters of a heat exchanger model without phase change was studied in this Master’s thesis using synthetically made data. A fast, two-step Markov chain Monte Carlo method (MCMC) was tested with a couple of case studies and a heat exchanger model. The two-step MCMC-method worked well and decreased the computation time compared to the traditional MCMC-method. The effect of measurement accuracy of certain control variables to the identifiability of parameters was also studied. The accuracy used did not seem to have a remarkable effect to the identifiability of parameters. The use of the posterior distribution of parameters in different heat exchanger geometries was studied. It would be computationally most efficient to use the same posterior distribution among different geometries in the optimisation of heat exchanger networks. According to the results, this was possible in the case when the frontal surface areas were the same among different geometries. In the other cases the same posterior distribution can be used for optimisation too, but that will give a wider predictive distribution as a result. For condensing surface heat exchangers the numerical stability of the simulation model was studied. As a result, a stable algorithm was developed.

Analysis and Control of Excitation, Field Weakening and Stability in Direct Torque Controlled Electrically Excited Synchronous Motor Drives

Direct torque control (DTC) is a new control method for rotating field electrical machines. DTC controls directly the motor stator flux linkage with the stator voltage, and no stator current controllers are used. With the DTC method very good torque dynamics can be achieved. Until now, DTC has been applied to asynchronous motor drives. The purpose of this work is to analyse the applicability of DTC to electrically excited synchronous motor drives. Compared with asynchronous motor drives, electrically excited synchronous motor drives require an additional control for the rotor field current. The field current control is called excitation control in this study. The dependence of the static and dynamic performance of DTC synchronous motor drives on the excitation control has been analysed and a straightforward excitation control method has been developed and tested. In the field weakening range the stator flux linkage modulus must be reduced in order to keep the electro motive force of the synchronous motor smaller than the stator voltage and in order to maintain a sufficient voltage reserve. The dynamic performance of the DTC synchronous motor drive depends on the stator flux linkage modulus. Another important factor for the dynamic performance in the field weakening range is the excitation control. The field weakening analysis considers both dependencies. A modified excitation control method, which maximises the dynamic performance in the field weakening range, has been developed. In synchronous motor drives the load angle must be kept in a stabile working area in order to avoid loss of synchronism. The traditional vector control methods allow to adjust the load angle of the synchronous motor directly by the stator current control. In the DTC synchronous motor drive the load angle is not a directly controllable variable, but it is formed freely according to the motor’s electromagnetic state and load. The load angle can be limited indirectly by limiting the torque reference. This method is however parameter sensitive and requires a safety margin between the theoretical torque maximum and the actual torque limit. The DTC modulation principle allows however a direct load angle adjustment without any current control. In this work a direct load angle control method has been developed. The method keeps the drive stabile and allows the maximal utilisation of the drive without a safety margin in the torque limitation.

Spare part business analysis and development

The purpose of this Thesis was to comprehensively analyze and develop the spare part business in Company Oy’s five biggest product groups by searching development issues related to single spare parts’ supply chains as well as the spare part business process, make implementation plans for them and implement the plans when possible. The items were classified based on special characteristics of spare parts and on their actual sales volumes. The created item classes were examined for finding improvement possibilities. Management strategies for classified items were suggested. Vendors and customers were analyzed for supporting the comprehensive supply network development work. The effectiveness of the current spare part business process was analyzed in co-operation with the spare part teams in three business unit locations. Several items were taken away from inventories as uselessly stocked items. Price list related to core items with one of the main product group’s core item manufacturer was suggested to be expanded in Town A. Refinement equipment seal item supply chain management was seen important to develop in Town B. A new internal business process model was created for minimizing and enhancing the internal business between Company’s business units. SAP inventory reports and several other features were suggested to be changed or developed. Also the SAP data material management was seen very important to be developed continuously. Many other development issues related to spare parts’ supply chains and the work done in the business process were found. The need for investigating the development possibilities deeper became very clear during the project.