Utilisation of biomass for energy production in the North-West Russian forest industry

Traditionally, fossil fuels have always been the major sources of the modern energy production. However prices on these energy sources have been constantly increasing. The utilization of local biomass resources for energy production can substitute significant part of the required energy demand in different energy sectors. The introduction of the biomass usage can easily be started in the forest industry first as it possesses biomass in a large volume. The forest industry energy sector has the highest potential for the fast bioenergy development in the North-West Russia. Therefore, the question concerning rational and effective forest resources use is important today as well as the utilization of the forestry by-products. This work describes and analyzes the opportunities of utilising biomass, mainly, in the form of the wood by-products, for energy production processes in general, as well as for the northwest Russian forest industry conditions. The study also covers basic forest industry processes and technologies, so, the reader can get familiar with the information about the specific character of the biomass utilization. The work gives a comprehensive view on the northwest forest industry situation from the biomass utilisation point of view. By presenting existing large-scale sawmills and pulp and paper mills the work provides information for the evaluation of the future development of CHP investments in the northwest Russian forest industry.

Kalman Filtering in Online Paper Quality Assessment

Controlling the quality variables (such as basis weight, moisture etc.) is a vital part of making top quality paper or board. In this thesis, an advanced data assimilation tool is applied to the quality control system (QCS) of a paper or board machine. The functionality of the QCS is based on quality observations that are measured with a traversing scanner making a zigzag path. The basic idea is the following: The measured quality variable has to be separated into its machine direction (MD) and cross direction (CD) variations due to the fact that the QCS works separately in MD and CD. Traditionally this is done simply by assuming one scan of the zigzag path to be the CD profile and its mean value to be one point of the MD trend. In this thesis, a more advanced method is introduced. The fundamental idea is to use the signals’ frequency components to represent the variation in both CD and MD. To be able to get to the frequency domain, the Fourier transform is utilized. The frequency domain, that is, the Fourier components are then used as a state vector in a Kalman filter. The Kalman filter is a widely used data assimilation tool to combine noisy observations with a model. The observations here refer to the quality measurements and the model to the Fourier frequency components. By implementing the two dimensional Fourier transform into the Kalman filter, we get an advanced tool for the separation of CD and MD components in total variation or, to be more general, for data assimilation. A piece of a paper roll is analyzed and this tool is applied to model the dataset. As a result, it is clear that the Kalman filter algorithm is able to reconstruct the main features of the dataset from a zigzag path. Although the results are made with a very short sample of paper roll, it seems that this method has great potential to be used later on as a part of the quality control system.

Massan fraktioiden vaikutus paperin bulkin ja sileyden väliseen yhteyteen

Diplomityön tavoitteena oli selvittää paperin valmistuksessa käytettävien mekaanisten massojen eri kuitufraktioiden vaikutusta SC-paperin ominaisuuksiin. Aikakausipaperin vaatimuksena on hyvä paperin sileys, kiilto ja bulkki. Sileys ja kiilto on helppo saavuttaa kalanteroimalla, mutta tällöin menetetään paperin bulkkia. Tässä työssä keskitytäänkin etsimään keinoja paperin bulkin säästämiseksi fraktioinnin avulla. Työn kirjallisuusosassa käydään läpi teoriaa paperin valmistuksesta ja paperin ominaisuuksista. Työn kokeellisessa osassa on esitetty tehdyt tutkimukset laboratoriomenetelmin kalanterointiolosuhteiden ja massojen eri fraktioiden vaikutuksesta paperin ominaisuuksiin. Saadut tulokset olivat samantyyppisiä mitä edellisissä tutkimuksissa samasta aiheesta oli saatu. Saatujen tulosten mukaan paperin pitkäkuitufraktion osuutta kasvattamalla bulkki ja taivutusjäykkyys paranivat, mutta toisaalta sileys ja kiilto huononivat. Paperin hienoainefraktion osuutta kasvattamalla kaikki painatusominaisuudet paranivat kuten sileys, kiilto ja valonsirontakerroin, mutta samalla huononivat paperin bulkki ja taivutusjäykkyys.

The effect of microfibrillated cellulose addition on drying shrinkage and dimensional stability of wood-free paper

Microfibrillated cellulose (MFC) is known to enhance strength properties of paper. Improved strength usually means increased bonding which is strongly connected to dimensional instability of paper. Dimensional instability is due to changes in moisture content of paper; when paper is moistened it expands and when dried, it shrinks. Hygroexpansion is linked to end-use problems and excessive drying shrinkage consumes strength potential. Effective use of materials requires controlling of these phenomena. There isn’t yet data concerning dimensional stability of papers containing MFC which restricts wider use of MFC. Main objective of the work was to evaluate dimensional stability of wood-free paper containing different amounts of MFC. Sheets were dried with different methods to see how drying strains effected on drying shrinkage and hygroexpansion. Also tensile strength was measured to find out the effect of MFC. Results were compared to sheets containing kraft fines and in some test points cationic starch was used alongside with MFC. MFC increased the dimensional instability of freely dried sheets. As the amounts of MFC increased the effects on dimensional stability became more severe. However the fineness of MFC didn’t play any important role. Both hygroexpansion and drying shrinkage were decreased with cationic starch addition. Prevention of drying shrinkage over powered the effects of additives on hygroexpansion. Tensile strength improved up till 7 % addition amount which could be set as the upper limit of MFC addition when paper preparation and tensile strength are concerned.

Imatran tehtaiden jätevesipäästöjen hallinta- ja analysointityökalun kehittäminen

Työn tavoitteena oli kehittää Stora Enso Oyj:n Imatran tehtaille Wedge-pohjainen analysointityökalu, jolla voidaan hallita prosessi- ja päästötietojen yhteys nykyistä paremmin. Wedgeen määriteltiin päästömittauksia, olennaisia prosessimittauksia ja tarpeelliset laskennat kuormituksen ennustamiseksi lähtien tuotantoprosessien tilasta. Työssä tehtiin kemialliselle ja biologiselle jätevedenpuhdistamolle meneville jätevesille laskennallisia malleja, joita verrattiin mitattuihin arvoihin. Kemialliselle jätevedenpuhdistamolle meneville jätevesille tehtiin malli jäteveden virtaamalle. Biologiselle jätevedenpuhdistamolle meneville jätevesille tehtiin mallit jäteveden virtaamalle sekä COD-, AOX- ja alkuainekuormituksille. Alkuaineista työhön otettiin mukaan natrium, rikki ja kloori. Teoriaosassa on käsitelty sellu- ja paperitehtaiden vedenkäyttöä, tehtaan eri osastojen jätevesikuormitusta, jäteveden puhdistusmenetelmiä sekä prosessidatan käsittelymenetelmiä. Kokeellisessa osassa on esitelty mitattujen ja laskennallisten mallien yhteyttä. Suurin osa laskennallisista malleista näyttää seuraavan kohtuullisen hyvin mitattuja arvoja. Kokeellisessa osassa on myös havainnollistettu esimerkkien avulla mallien hyödyntämistä. Työn hyötynä on normaalien kuormitusvaihteluiden ja häiriöpäästöjen entistä tarkempi ja nopeampi erottelu. Pitkällä tähtäimellä Wedge-ohjelman avulla pystytään keskittämään jätevesikuormituksen vähentämistoimenpiteet olennaisimpiin kohteisiin.

Kunnossapidon nykytila metsäteollisuuden voimalaitoksissa

Tämän diplomityön tavoitteena oli kartoittaa kunnossapidon nykytilaa metsäteollisuuden voimalaitoksissa. Asiaa selvitettiin kvalitatiivisena tutkimuksena, jossa haastateltiin kunnossapidon vastuuhenkilöitä. Tutkimuksen kohteeksi valittiin kahdeksan erikokoista voimalaitosta, jotka edustivat suurimpia Suomessa toimivia metsäteollisuuden konserneja. Työssä käsiteltiin tiedon ja materiaalin hallintaa, kunnossapidon suunnittelua ja organisointia sekä taloudellisia vaikutuksia. Tulokset on esitetty yleisessä muodossa ilman laitoskohtaista erittelyä. Metsäteollisuus toimii hyvin globaaleilla markkinoilla, joilla kilpailu on kiristynyt viime vuosina. Tehokkuutta on pyritty parantamaan kaikilla sektoreilla ja tämä näkyy muutoksena monilla kunnossapidon osa alueilla. Merkittävä muutos oli kunnossapitotoimintojen eriyttäminen omaksi yhtiöksi, joka oli toteutettu yhtiön strategisena valintana puolella tehtaista. Tutkimuksessa kävi myös ilmi, että henkilökunnan koulutukseen panostamalla tietojärjestelmiä voidaan hyödyntää tehokkaammin. Varastoon sidotun pääoman pienentäminen on merkinnyt materiaalilogistiikan tärkeyden korostumista tavoiteltaessa parempaa käyttövarmuutta. Kun lisäksi teollisuuden investointien määrät ovat viime vuosina laskeneet, on kunnossapidon ja etenkin sen suunnittelun rooli kasvanut.

Optimization of energy in a pulp mill

This study presents examination of ways to increase power generation in pulp mills. The main purpose was to identify and verify the best ways of power generation growth. The literature part of this study presented operation of energy pulp mill departments, energy consumption and generation by the recovery and power boilers. The second chapter of this part described the main directions for increase of electricity generation rise of black liquor dry solid content, increase of main steam parameters, flue gas heat recovery technologies, feed water and combustion air preheating. The third chapter of the literature part presented possible technical, environment and corrosion risks appeared from described alternatives. In the experimental part of this study, calculations and results of possible models with alternatives was presented. The possible combinations of alternatives were generated in 44 `models of energy pulp mill. The target of this part was define extra electricity generation after alternatives using and estimate profitability of generated models. The calculations were made by computer programme PROSIM. In the conclusions, the results were estimated on the basis of extra electricity generation and equipment design data of models. The profitability of cases was verified by their payback periods and additional incomes.

The effect of pulp washing on bleaching efficiency

The main aim of this study was to inspect the influence of the ultrafiltration implementation on the washing and on bleaching efficiency. Four cases corresponding to four washing stages were observed: two with hardwood pulp and two with softwood pulp; each case had a reference and a trial experiment. The experiments with hardwood pulp were arranged in a manner to explore predominantly the possibility of bleaching performance improvement by applying for washing instead of untreated filtrate (reference case) the same treated one (trial case). Despite that the ultrafiltration reduced the COD of the wash filtrates allowing the decreasing of COD carry-over to the bleaching stage it didn’t affect the bleaching performance. Another set was used in the experiments with softwood pulp. It implied the ultrafiltration and recirculation of the filtrate to the same washing stage with the purpose to reduce the volumes and pollution of the bleaching effluents. In one case the negative result was obtained which was expressed by worse parameters of the pulp after bleaching. Another case showed the opportunity to replace hot water with the filtrate and reduce the fresh water consumption.

Enhancing Customer Knowledge and Its Sharing At a Paper Production Line

This study has been made for specific paper production line at an international forest industry company in Finland. The main purpose for the study was a need to examine the current situation of the customer knowledge and its’ sharing at case production line, recognize the problems in it and finally, find out the improvement actions. The study is composed of theoretical and empirical parts. In theoretical part, knowledge management and information sharing in addition to customer knowledge management are presented. Empirical data from case production line was collected by using survey questionnaires. The results are analyzed in discussion and conclusions and finally, study ends with summary which includes recommendations. Based on the study, the amount and quality of customer knowledge and gaining and transferring the customer knowledge were found as the main challenges. The proposed solutions were discovered from moving towards more dynamic operating environment and in the area of customer knowledge management, especially from the communities of creation.

Märkäosan lisäaineet ja kuituflokit konesihdin ympäristössä

Painelajittelu on yksi yleisimmistä yksikköprosesseista paperin ja sellun valmistuksessa. Suurelta osin lajittimet toimivat niille asetettujen vaatimusten mukaisesti, mutta joissakin tapauksissa lajittimissa saattaa esiintyä ei-toivottavaa kuitujen kasautumista sekä kehräymän muodostusta. Niiden seurauksena lajittimien kapasiteetti alenee ja lajittelutulos heikkenee. Tämän työn tarkoituksena on uutta kuvantamistekniikkaa hyödyntäen selvittää miten kehräymät ja kuitukasaumat syntyvät painelajittimen sihtipinnalla ja miten retentioaineen syöttö sihdin ympäristössä vaikuttaa niiden syntyyn. Työn kirjallisuusosassa tarkastellaan painelajittimen toimintaa, rakennetta sekä lyhyen kierron konesihdin erityispiirteitä. Lisäksi tarkastellaan retentiokemikaalien käyttäytymistä leikkausvoimien alaisuudessa ja kuitukehräymien syntyä painelajittimissa. Kokeellisessa osassa on raportoitu kuvantamisjärjestelmällä saatuja tuloksia sekä esitetään havaintoja kehräymien ja kuitukasaumien synnystä ja niiden vaikutuksista painelajittimen toimintaan. Kuvausten perusteella voidaan sanoa, että kehräymän syntyminen sihdissä vaatii aina jonkinlaisen kuitukasauman olemassaoloa. Tällaista alkukasaumaa tarvitaan, jotta kuidut voivat ankkuroitua siihen kiinni ja johon kiinnittyneenä kuidut alkavat pyöriä virtauksessa muodostaen kehräymää. Kuitukasauman muodostuminen painelajittimessa johtuu pääosin sihdissä olevasta epäjatkuvuuskohdasta, massassa olevista epäpuhtauksista ja kuituflokeista jotka jäävät kiinni sihtipinnan aukkoihin tai lajittimen kapasiteetin ylittymisestä. Kehräymän syntyä kasauman jäljessä voidaan pitää enemmän sääntönä kuin poikkeuksena, mutta kehräytyminen on vähäisempää reikäsihdillä kuin rakosihdillä. Silloituspolymeerillä flokattu massa ei muodosta herkemmin kuitukasaumia sihtipintaan verrattuna flokkaamattomaan massaan. Lajiteltavan massan sakeuden nosto vähentää kuitukasaumien ja kehräymien syntyä. Kuitukasaumien ja kehräymien välttämiseksi on tärkeää, että sihtiä ei ajeta suunniteltua mitoitusaluetta suuremmilla tuotannoilla tai virtauksilla.

The Impact of Aspen and Alder on the Quality of NHBK

The purpose of this work was to study the effect of aspen and alder on birch cooking and the quality of the pulp produced. Three different birch kraft pulps were studied. As a reference, pure aspen and alder were included. The laboratory trials were done at the UPM Research Centre in Lappeenranta, Finland. The materials used were birch, aspen and alder mill chips that were collected around the area of South-Carelia in Finland. The chips used in the study were pulped using a standard kraft process. The pulps including birch fibres were ECF-bleached at laboratory scale to a target brightness of 85 %. The bleached pulps were beaten at low consistency by a laboratory Voith Sulzer refiner and tested for optical and physical properties. The theoretical part is a study of hardwoods that takes into accounts the differences between birch, aspen and alder. Major sub-areas were fibre and paper-technical properties as well as chemical composition and their influence on the different properties. The pulp properties of birch, aspen and alder found in previous studies were reported. Russian hardwood forest resources were also investigated. The fundamentals of kraft pulping and bleaching were studied at the end of theoretical part. The major effect of replacing birch with aspen and alder was the deterioration (lowering) of tensile and tear strengths. In other words, addition of aspen and alder to a birch furnish reduced strength properties. The reinforcement ability of the tested pulps was the following: 100 % birch > 80 % birch, 20 % aspen > 70 % birch, 20 % aspen, 10 % alder. The second thing noted was that blending of birch together with aspen and alder give better smoothness, optical properties and also formation. It can be concluded, that replacement of birch with alder during cooking by more than 10 % can negatively affect on the paper-technical properties of birch pulp. Mixing pure birch and aspen pulps would be more beneficial when producing printing paper made from chemical pulp.

Engendering Group Support Based Foresight for Capital Intensive Manufacturing Industries - Case Paper and Steel Industry Scenarios by 2018

In recent times of global turmoil, the need for uncertainty management has become ever momentous. The need for enhanced foresight especially concerns capital-intensive industries, which need to commit their resources and assets with long-term planning horizons. Scenario planning has been acknowledged to have many virtues - and limitations - concerning the mapping of the future and illustrating the alternative development paths. The present study has been initiated to address both the need of improved foresight in two capital-intensive industries, i.e. the paper and steel industries and the imperfections in the current scenario practice. The research problem has been approached by engendering a problem-solving vehicle, which combines, e.g. elements of generic scenario process, face-to-face group support methods, deductive scenario reasoning and causal mapping into a fully integrated scenario process. The process, called the SAGES scenario framework, has been empirically tested by creating alternative futures for two capital-intensive industries, i.e. the paper and steel industries. Three scenarios for each industry have been engendered together with the identification of the key megatrends, the most important foreign investment determinants, key future drivers and leading indicators for the materialisation of the scenarios. The empirical results revealed a two-fold outlook for the paper industry, while the steel industry future was seen as much more positive. The research found support for utilising group support systems in scenario and strategic planning context with some limitations. Key perceived benefits include high time-efficiency, productivity and lower resource-intensiveness. Group support also seems to enhance participant satisfaction, encourage innovative thinking and provide the users with personalised qualitative scenarios.

Computational and Experimental Investigation of the Grooved Roll in Paper Machine Environment

In the paper machine, it is not a desired feature for the boundary layer flows in the fabric and the roll surfaces to travel into the closing nips, creating overpressure. In this thesis, the aerodynamic behavior of the grooved roll and smooth rolls is compared in order to understand the nip flow phenomena, which is the main reason why vacuum and grooved roll constructions are designed. A common method to remove the boundary layer flow from the closing nip is to use the vacuum roll construction. The downside of the use of vacuum rolls is high operational costs due to pressure losses in the vacuum roll shell. The deep grooved roll has the same goal, to create a pressure difference over the paper web and keep the paper attached to the roll or fabric surface in the drying pocket of the paper machine. A literature review revealed that the aerodynamic functionality of the grooved roll is not very well known. In this thesis, the aerodynamic functionality of the grooved roll in interaction with a permeable or impermeable wall is studied by varying the groove properties. Computational fluid dynamics simulations are utilized as the research tool. The simulations have been performed with commercial fluid dynamics software, ANSYS Fluent. Simulation results made with 3- and 2-dimensional fluid dynamics models are compared to laboratory scale measurements. The measurements have been made with a grooved roll simulator designed for the research. The variables in the comparison are the paper or fabric wrap angle, surface velocities, groove geometry and wall permeability. Present-day computational and modeling resources limit grooved roll fluid dynamics simulations in the paper machine scale. Based on the analysis of the aerodynamic functionality of the grooved roll, a grooved roll simulation tool is proposed. The smooth roll simulations show that the closing nip pressure does not depend on the length of boundary layer development. The surface velocity increase affects the pressure distribution in the closing and opening nips. The 3D grooved roll model reveals the aerodynamic functionality of the grooved roll. With the optimal groove size it is possible to avoid closing nip overpressure and keep the web attached to the fabric surface in the area of the wrap angle. The groove flow friction and minor losses play a different role when the wrap angle is changed. The proposed 2D grooved roll simulation tool is able to replicate the grooved aerodynamic behavior with reasonable accuracy. A small wrap angle predicts the pressure distribution correctly with the chosen approach for calculating the groove friction losses. With a large wrap angle, the groove friction loss shows too large pressure gradients, and the way of calculating the air flow friction losses in the groove has to be reconsidered. The aerodynamic functionality of the grooved roll is based on minor and viscous losses in the closing and opening nips as well as in the grooves. The proposed 2D grooved roll model is a simplification in order to reduce computational and modeling efforts. The simulation tool makes it possible to simulate complex paper machine constructions in the paper machine scale. In order to use the grooved roll as a replacement for the vacuum roll, the grooved roll properties have to be considered on the basis of the web handling application.

Improving Cross Direction Basis Weight Profile in a Fourdrinier Paper Machine

The purpose of this study was to improve PM7’s basis weight CD profile in Stora Enso’s Berghuizer mill and to search mechanical defects which affect to the formation of the basis weight CD profile. In the theoretical part PM7’s structure was presented and the formation of the basis weight and caliper CD profiles was examined as well as disturbances which are affecting to the formation. The function of the control system was scrutinised for the side of CD profiles as well as the formation of the measured CD profiles. Tuning of the control system was examined through the response model and filtering. Specification of the response model and filtering was explained and how to determine 2sigma statistical number. In the end of the theoretical part ATPA hardware and a new profile browser were introduced. In the experimental part focus was in the beginning to search and remove mechanical defects which are affecting to CD profiles. The next step was to verify the reliability of the online measurements, to study the stability of the basis weight CD profile and to find out so called fingerprint, a basis weight CD profile which is unique for each paper machine. New response model and filtering value for basis weight CD profile was determined by bump tests. After a follow up period the affect of the new response model and filtering was analysed.

Wet oxidation of recalcitrant lignin waters: Experimental and kinetic studies

The dissertation is based on four articles dealing with recalcitrant lignin water purification. Lignin, a complicated substance and recalcitrant to most treatment technologies, inhibits seriously pulp and paper industry waste management. Therefore, lignin is studied, using WO as a process method for its degradation. A special attention is paid to the improvement in biodegradability and the reduction of lignin content, since they have special importance for any following biological treatment. In most cases wet oxidation is not used as a complete ' mineralization method but as a pre treatment in order to eliminate toxic components and to reduce the high level of organics produced. The combination of wet oxidation with a biological treatment can be a good option due to its effectiveness and its relatively low technology cost. The literature part gives an overview of Advanced Oxidation Processes (AOPs). A hot oxidation process, wet oxidation (WO), is investigated in detail and is the AOP process used in the research. The background and main principles of wet oxidation, its industrial applications, the combination of wet oxidation with other water treatment technologies, principal reactions in WO, and key aspects of modelling and reaction kinetics are presented. There is also given a wood composition and lignin characterization (chemical composition, structure and origin), lignin containing waters, lignin degradation and reuse possibilities, and purification practices for lignin containing waters. The aim of the research was to investigate the effect of the operating conditions of WO, such as temperature, partial pressure of oxygen, pH and initial concentration of wastewater, on the efficiency, and to enhance the process and estimate optimal conditions for WO of recalcitrant lignin waters. Two different waters are studied (a lignin water model solution and debarking water from paper industry) to give as appropriate conditions as possible. Due to the great importance of re using and minimizing the residues of industries, further research is carried out using residual ash of an Estonian power plant as a catalyst in wet oxidation of lignin-containing water. Developing a kinetic model that includes in the prediction such parameters as TOC gives the opportunity to estimate the amount of emerging inorganic substances (degradation rate of waste) and not only the decrease of COD and BOD. The degradation target compound, lignin is included into the model through its COD value (CODligning). Such a kinetic model can be valuable in developing WO treatment processes for lignin containing waters, or other wastewaters containing one or more target compounds. In the first article, wet oxidation of "pure" lignin water was investigated as a model case with the aim of degrading lignin and enhancing water biodegradability. The experiments were performed at various temperatures (110 -190°C), partial oxygen pressures (0.5 -1.5 MPa) and pH (5, 9 and 12). The experiments showed that increasing the temperature notably improved the processes efficiency. 75% lignin reduction was detected at the lowest temperature tested and lignin removal improved to 100% at 190°C. The effect of temperature on the COD removal rate was lower, but clearly detectable. 53% of organics were oxidized at 190°C. The effect of pH occurred mostly on lignin removal. Increasing the pH enhanced the lignin removal efficiency from 60% to nearly 100%. A good biodegradability ratio (over 0.5) was generally achieved. The aim of the second article was to develop a mathematical model for "pure" lignin wet oxidation using lumped characteristics of water (COD, BOD, TOC) and lignin concentration. The model agreed well with the experimental data (R2 = 0.93 at pH 5 and 12) and concentration changes during wet oxidation followed adequately the experimental results. The model also showed correctly the trend of biodegradability (BOD/COD) changes. In the third article, the purpose of the research was to estimate optimal conditions for wet oxidation (WO) of debarking water from the paper industry. The WO experiments were' performed at various temperatures, partial oxygen pressures and pH. The experiments showed that lignin degradation and organics removal are affected remarkably by temperature and pH. 78-97% lignin reduction was detected at different WO conditions. Initial pH 12 caused faster removal of tannins/lignin content; but initial pH 5 was more effective for removal of total organics, represented by COD and TOC. Most of the decrease in organic substances concentrations occurred in the first 60 minutes. The aim of the fourth article was to compare the behaviour of two reaction kinetic models, based on experiments of wet oxidation of industrial debarking water under different conditions. The simpler model took into account only the changes in COD, BOD and TOC; the advanced model was similar to the model used in the second article. Comparing the results of the models, the second model was found to be more suitable for describing the kinetics of wet oxidation of debarking water. The significance of the reactions involved was compared on the basis of the model: for instance, lignin degraded first to other chemically oxidizable compounds rather than directly to biodegradable products. Catalytic wet oxidation of lignin containing waters is briefly presented at the end of the dissertation. Two completely different catalysts were used: a commercial Pt catalyst and waste power plant ash. CWO showed good performance using 1 g/L of residual ash gave lignin removal of 86% and COD removal of 39% at 150°C (a lower temperature and pressure than with WO). It was noted that the ash catalyst caused a remarkable removal rate for lignin degradation already during the pre heating for `zero' time, 58% of lignin was degraded. In general, wet oxidation is not recommended for use as a complete mineralization method, but as a pre treatment phase to eliminate toxic or difficultly biodegradable components and to reduce the high level of organics. Biological treatment is an appropriate post treatment method since easily biodegradable organic matter remains after the WO process. The combination of wet oxidation with subsequent biological treatment can be an effective option for the treatment of lignin containing waters.