Fractionation of wood hydrolysate by ultrafiltration membranes at high temperature

Ultrafiltration (UF) is already used in pulp and paper industry and its demand is growing because of the required reduction of raw water intake and the separation of useful compounds from process waters. In the pulp and paper industry membranes might be exposed to extreme conditions and, therefore, it is important that the membrane can withstand them. In this study, extractives, hemicelluloses and lignin type compounds were separated from wood hydrolysate in order to be able to utilise the hemicelluloses in the production of biofuel. The performance of different polymeric membranes at different temperatures was studied. Samples were analysed for total organic compounds (TOC), lignin compounds (UV absorption at 280 nm) and sugar. Turbidity, conductivity and pH were also measured. The degree of fouling of the membranes was monitored by measuring the pure water flux before and comparing it with the pure water flux after the filtration of hydrolysate. According to the results, the retention of turbidity was observed to be higher at lower temperature compared to when the filtrations were operated at high temperature (70 °C). Permeate flux increased with elevated process temperature. There was no detrimental effect of temperature on most of the membranes used. Microdyn-Nadir regenerated cellulose membranes (RC) and GE-Osmonics thin film membranes seemed to be applicable in the chosen process conditions. The Polyethersulphone (NF-PES-10 and UH004P) and polysulphone (MPS-36) membranes used were highly fouled, but they showed high retentions for different compounds.

Recovery of Hemicelluloses from Wood Hydrolysates by Membrane Filtration

Hemicelluloses are among the most important natural resources that contain polysaccharides. In this study the separation and purification of hemicelluloses from water extraction liquors containing wood hemicelluloses, lignin compounds and monosaccharide by using membrane filtration was investigated. The isolation of the hemicelluloses from the wood hydrolysates was performed in two steps: concentration of high molar mass hemicelluloses by ultrafiltration and separation of low molar mass hemicelluloses from monomeric sugars using tight ultrafiltration membranes. The purification of the retained hemicelluloses was performed by diafiltration. During the filtration experiments, the permeate flux through ultrafiltration and tight ultrafiltration membranes was relatively high. The fouling ability of the used membranes was relatively low. In our experiments, the retention of hemicelluloses using two filtration steps was almost complete. The separation of monosaccharides from hemicelluloses was relatively high and the purification of hemicelluloses by diafiltration was highly efficient. The separation of lignin from hemicelluloses was partially achieved. Diafiltration showed potential to purify retained hemicelluloses from lignin and other organics. The best separation of lignin from hemicelluloses in the first filtration step was obtained using the UC005 membrane. The GE-5 and ETNA01PP membranes showed potential to purify and separate lignin from hemicelluloses. However, the feed solution of the second filtration stages (from different ultrafiltration membranes) affected the permeate flux and the separation of various extracted compounds from hemicelluloses. The GE-5 and ETNA01PP membranes gave the efficient purification of the hemicelluloses when using diafiltration. Separation of degraded xylan from glucomannan (primary spruce hemicelluloses) was also possible using membrane filtration. The best separation was achieved using the GE-5 membrane. The retention of glucomannan was three times higher than xylan retention.

Fractionation of Wood Extracts

The aim of this thesis was to fractionate wood extracts into pure fractions using membrane technology, to observe membrane behaviour in solvents and to study the effect of conditioning on membrane performance. Four different wood extracts were used in the performed filtrations. In the literature part, the focus was on the effect of different solvent properties on polymeric membranes, especially on their retention and flux. Solute properties, such as shape, polarity and charge, were examined. Transport models, membrane stability and ways to improve the stability, when solvents were filtered, were also discussed. The experimental part consisted of a series of filtrations, where the effect of the wood extracts and solvent concentration on solute retention was observed. Polymeric and ceramic membranes were tested under different conditions and the solute analyses were performed with GC and GC-MS. It was discovered that it is possible to fractionate wood extracts using membrane technology to some extent, but more research must be done to understand the mechanisms behind the various interactions between the solvent and the membrane. Conditioning was also considered as an important part of the membrane pre-treatment.

Bioenergiaa ja ravinteita kasvi- ja eläinperäisistä sivuainevirroista Parikkalassa

Euroopan unionissa pyritään lisäämään uusiutuvien energialähteiden käyttöä. Tämän työn tavoitteena oli selvittää Parikkalan kunnan alueella muodostuvat biomassat sekä tutkia niiden hyötykäyttömahdollisuuksia sähkön, lämmön sekä lannoitteiden tuotannossa. Käsiteltäviä biomassoja ovat eläintilojen lietteet ja lannat, biojätteet ja yhdyskuntalietteet, vesistöjen kunnostuksessa syntyvät biomassat sekä peltobiomassat ja metsäbiomassa. Mädätyksen kannalta olennaisinta on materiaalien kosteus ja haihtuvan orgaanisen aineksen pitoisuus sekä siitä saatava biokaasumäärä. Poltossa polttoaineen kuiva-aineen lämpöarvo ja kosteus määrittelevät saadun hyödyn. Kompostoinnissa on tärkeää huolehtia riittävästä ilman saannista ja riittävästä viipymäajasta. Hyödynnettäessä biokaasua sähkön ja lämmön yhteistuotannossa on tärkeää löytää hyötykäyttö myös muodostuvalle lämmölle. Poltosta saatavan tuhkan hyötykäyttö onnistuu metsälannoitteena, kun poltetaan turvetta tai puuta. Kompostia voidaan hyödyntää maanparannusaineena. Parikkalan alueella tarkasteltiin biomassojen nykyistä ja mahdollista tulevaa hyötykäyttöä. Tarkastelu tehtiin skenaarioiden avulla. Skenaarioihin kuuluvat mädätyksen ja polton maksimipotentiaalit sekä keskitetyn ja hajautetun käsittelyn skenaariot. Alueelta on saatavissa paljon biomassoja, joista massaltaan suurin on eläintilojen lannat. Alueella on hankaluutena löytää sopiva kulutuskohde biokaasusta tuotetulle lämmölle, mutta sopivana kohteena voisi toimia alueella oleva suuri sikala tai lämpökeskukset.

Research of wood fuel market in Ukraine and the Republic of Belarus

The goal of the present work was to describe the wood fuel market of Ukraine and the Republic of Belarus, to estimate wood fuel potential and to research opportunities of wood fuel trading. Nowadays the wood waste, wood residues and by-products are becoming more and more potential raw materials for energy production. Against the background of unstable prices of traditional energy sources and environmental degradation, European States are planning to get 12% of energy from alternative sources already in 2010. Wastes of wood-working and agricultural productions are such sources. At present time the most popular wood biofuels are wood pellets, briquettes, wood chips and logs. Ukraine and the Republic of Belarus have a rather big potential of wood fuel resources. But wood fuels markets of these countries are on the entry level and quite disorganized. There is almost no domestic usage of wood biofuel. All produced pellets, briquettes as well as wood chips and logs go to the export, but the volumes are not high at present time. Ukraine and the Republic of Belarus have a very suitable geographical location. The most promising directions of wood fuel trading are developed wood fuel markets of Northern countries, Austria, Germany as well as actively developing markets of Poland and Hungary. At the long distance truck and sea transportation are the most appropriate. At a short distance cheap transportation by rail is more suitable. Thereby export is a potential opportunity for development of wood fuel production and in the future for usage in the researched countries.

Research of wood fuel market in North-West of Russia

The main purposes of this study are analyzing of forest sector of North-West and research of potentials of wood fuel market in this region. Research is focused on definition of the most perspective areas for export of wood fuel: logging residues, industrial wood processing residues, pellets and briquettes. Russian wood energy industry is very young in comparison with European countries. Nowadays there are no support and serious attention from the government to this sector. Hence almost all wood fuel market is oriented to the Western Europe. Export of wood fuel is dominated over the internal consumption. Pellet production in North –West is rapidly growing. Despite internal market has been developed the lion's share of pellets goes to export. Part of industrial wood processing residues is used by producers for their own goals, part goes to the export and rest of them is not used at all. Logging residues as raw materials for fuel have great potentials; most of them are left in a forest. Special techniques for their processing are too expensive for Russian entrepreneur. Some parts of North –West, which are situated close to the border with European countries, are potential for export. Political, economical and logistical challenges are complicated facilities for foreign customer to purchase wood fuel in remote parts of North-West. However some decisions for solving this problem exist and Russian manufactures are still interested in export of their products.

Rakennukset ja rakentajat Raision Ihalassa rautakauden lopulla ja varhaisella keskiajalla

Turun yliopiston arkeologian oppiaine tutki Raision Ihalan historiallisella kylätontilla, ns. Mullin eduspellolla, asuinpaikan, josta löydettiin maamme oloissa harvinaisen hyvin säilyneitä rakennusten puuosien jäännöksiä. Löytö on ainutlaatuinen Suomen oloissa ja sillä on kansainvälistäkin merkitystä, koska hyvin säilyneet myöhemmän rautakauden ja varhaisen keskiajan maaseutuasuinpaikat, joista tavataan puujäännöksiä, ovat harvinaisia erityisesti itäisen Itämeren piirissä. Rakennukset on ennallistettu käyttäen tiukkaa paikallisen analogian (’Tight Local Analogy’) metodia, erityisesti suoraa historiallista analogista lähestymistapaa. Tätä tarkoitusta varten muodostettiin aluksi arkeologinen, historiallinen ja etnografinen lähdemalli. Tämä valittiin maantieteellisesti ja ajallisesti relevantista tutkimusaineistosta pohjoisen Itämeren piiristä. Tiedot lounaisen Suomen rakennuksista ja rakennusteknologiasta katsottiin olevan tärkein osa mallia johtuen historiallisesta ja spatiaalisesta jatkuvuudesta. Lähdemalli yhdistettiin sitten Mullin arkeologiseen aineistoon ja analyysin tuloksena saatiin rakennusten ennallistukset. Mullista on voitu ennallistaa ainakin kuusi eri rakennusta neljässä eri rakennuspaikassa. Rakennusteknologia perustui kattoa kannattaviin horisontaalisiin pitkiin seinähirsiin, jotka oli nurkissa yhdistetty joko salvoksella tai varhopatsaalla. Kaikissa rakennuksissa ulkoseinän pituus oli 5 – 7 metriä. Löydettiin lisäksi savi- ja puulattioita sekä kaksi tulisijaa, savikupoliuuni ja avoin liesi. Runsaan palaneen saven perusteella on mahdollista päätellä, että katto oli mitä todennäköisimmin kaksilappeinen vuoliaiskatto, joka oli katettu puulla ja/tai turpeella. Kaikki rakennukset olivat samaa tyyppiä ja ne käsittivät isomman huoneen ja kapean eteisen. Kaikki analysoitu puu oli mäntyä. Ulkoalueelta tavattiin lisäksi tunkioita, ojia, aitoja ja erilaisia varastokuoppia. Rakennukset on ajoitettu 900-luvun lopulta 1200-luvun lopulle (cal AD). Lopuksi tutkittiin rakennuksia yhteisöllisessä ympäristössään, niiden ajallista asemaa sekä asukkaiden erilaisia spatiaalisia kokemuksia ja yhteyksiä. Raision Ihalaa analysoidaan sosiaalisen identiteetin ja sen materiaalisten ilmenemismuotojen kautta. Nämä sosiaaliset identiteetit muodostuvat kommunikaatioverkostoista eri spatiaalisilla ja yhteisöllisillä ta¬soilla. Näitä eri tasoja ovat: 1) kotitalous arjen toimintoineen, perhe ja sukulaisuussuhteet traditioineen; 2) paikallinen identiteetti, rakennus, rakennuspaikka, asuinpaikan ympäristö ja sen käyttö, (maa)talo ja kylä; 3) Raision Ihalan kylä laajemmassa alueellisessa kontekstissaan pohjoisen Itämeren piirissä: kauppiaiden ja käsityöläisten kontaktiverkostot, uskonnollinen identiteetti ja sen muutokset.

Wood pellet markets in Russia

Bioenergy came to Russia through wood pellets. On account of prevalence of oil and gas in the Russian economy «bioenergy» has come with a great delay. Certainly, there were many woodworking enterprises and even municipal boiler-houses using wood waste and fire wood for energy reception, but this activity was not purposeful. More likely it was connected with necessity of waste recycling and with the organization of heat supply in the remote areas of the country. However, in 2001 was founded the first pellet plant in Russia. The purpose of this work was to analyze wood pellets market in Russia, investigate current situation on the home and export market, evaluates supply and demand development, opportunities for wood pellets manufactures in Russia, the main manufactures in Russian market; cost and prices for wood pellets in Russia. Also the work was intended to give better understanding of the main problems of wood pellets industry in Russia. Besides, this work had updated information about Russian customs and logistic systems.

The effect of microfibrillated cellulose addition on drying shrinkage and dimensional stability of wood-free paper

Microfibrillated cellulose (MFC) is known to enhance strength properties of paper. Improved strength usually means increased bonding which is strongly connected to dimensional instability of paper. Dimensional instability is due to changes in moisture content of paper; when paper is moistened it expands and when dried, it shrinks. Hygroexpansion is linked to end-use problems and excessive drying shrinkage consumes strength potential. Effective use of materials requires controlling of these phenomena. There isn’t yet data concerning dimensional stability of papers containing MFC which restricts wider use of MFC. Main objective of the work was to evaluate dimensional stability of wood-free paper containing different amounts of MFC. Sheets were dried with different methods to see how drying strains effected on drying shrinkage and hygroexpansion. Also tensile strength was measured to find out the effect of MFC. Results were compared to sheets containing kraft fines and in some test points cationic starch was used alongside with MFC. MFC increased the dimensional instability of freely dried sheets. As the amounts of MFC increased the effects on dimensional stability became more severe. However the fineness of MFC didn’t play any important role. Both hygroexpansion and drying shrinkage were decreased with cationic starch addition. Prevention of drying shrinkage over powered the effects of additives on hygroexpansion. Tensile strength improved up till 7 % addition amount which could be set as the upper limit of MFC addition when paper preparation and tensile strength are concerned.

Non-resorbable glass fibre-reinforced composite with porous surface as bone substitute material: Experimental studies in vitro and in vivo focused on bone-implant interface

The development of load-bearing osseous implant with desired mechanical and surface properties in order to promote incorporation with bone and to eliminate risk of bone resorption and implant failure is a very challenging task. Bone formation and resoption processes depend on the mechanical environment. Certain stress/strain conditions are required to promote new bone growth and to prevent bone mass loss. Conventional metallic implants with high stiffness carry most of the load and the surrounding bone becomes virtually unloaded and inactive. Fibre-reinforced composites offer an interesting alternative to metallic implants, because their mechanical properties can be tailored to be equal to those of bone, by the careful selection of matrix polymer, type of fibres, fibre volume fraction, orientation and length. Successful load transfer at bone-implant interface requires proper fixation between the bone and implant. One promising method to promote fixation is to prepare implants with porous surface. Bone ingrowth into porous surface structure stabilises the system and improves clinical success of the implant. The experimental part of this work was focused on polymethyl methacrylate (PMMA) -based composites with dense load-bearing core and porous surface. Three-dimensionally randomly orientated chopped glass fibres were used to reinforce the composite. A method to fabricate those composites was developed by a solvent treatment technique and some characterisations concerning the functionality of the surface structure were made in vitro and in vivo. Scanning electron microscope observations revealed that the pore size and interconnective porous architecture of the surface layer of the fibre-reinforced composite (FRC) could be optimal for bone ingrowth. Microhardness measurements showed that the solvent treatment did not have an effect on the mechanical properties of the load-bearing core. A push-out test, using dental stone as a bone model material, revealed that short glass fibre-reinforced porous surface layer is strong enough to carry load. Unreacted monomers can cause the chemical necrosis of the tissue, but the levels of leachable resisidual monomers were considerably lower than those found in chemically cured fibre-reinforced dentures and in modified acrylic bone cements. Animal experiments proved that surface porous FRC implant can enhance fixation between bone and FRC. New bone ingrowth into the pores was detected and strong interlocking between bone and the implant was achieved.

Factors affecting the usability of aspen (Populus tremula) wood dried at different temperature levels

In this dissertation the main aim was to study the usability of aspen wood in the mechanical wood processes, especially the factors that affect the usability of aspen wood, which is dried at different temperature levels. The problematic of varying temperatures from level to another seem to have significant effects on distortions. According to the studies conducted, many practical solutions for drying of aspen timber can be made. European aspen sawn timber should be dried in relatively narrow widths, short lengths, edged and sawn pith free. The results achieved give an interesting view for the distortions of aspen wood between HT drying and heat treatment. The most significant result is that cupping seems to decrease when increasing temperature level from HT drying to heat treatment phase. The difference is significant. Other very obvious result is that bow and crook are increasing between these two temperature levels, bow significantly. Also the modelling gives a good background for this result since cupping is reduced by higher temperatures. It can also be assumed that these distortions can be affected for example by sorting out the timber used to different moisture levels before drying. This could be a very simple solution for practical purposes. From practical point of view, it was also noted during the drying tests performed that the discoloration seem to be no problem for aspen boards dried in temperatures under 150 °C. Altogether, this dissertation covers many interesting points of view of factors affecting distortions of wood in different temperature stages. Aspen as species in use of mechanical wood industries seems to be a species suitable for component production. According to the results, the best yield from aspen timber can be achieved in industry that can utilize relatively short components of sawn wood. Results achieved give a significant indication about the factors affecting distortions of wood at different temperature stages of drying, especially considering European aspen.

Kierrätyspolttoaineiden käyttö leijukerrospoltossa vetykaasun kanssa

Tämä diplomityö on tehty Leppäkosken Energia Oy:n ja Kemira Chemicals Oy:n yhteisyritys FC Energia Oy:lle. FC Energia Oy suunnittelee rakentaa uutta bio-vetyvoimalaitosta Sastamalaan. Voimalaitoksella tuotettaisiin Kemira Chemicals Oy:n ylijäämävedystä ja biopolttoaineista sähköä, kaukolämpöä ja prosessihöyryä. Ympäristölupaa on haettu hakkeen, turpeen ja kierrätyspuun poltolle vetykaasun kanssa. Voimalaitoksen kattilan toiminta perustuu kuplivaan leijukerrostekniikkaan. Diplomityössä selvitettiin, mitä muutoksia kierrätyspolttoaineiden käyttö vaatii leijukerrospoltossa verrattuna hakkeen ja turpeen polttoon. Kierrätyspolttoaineena käytetään hyvälaatuista kierrätyspuuta. Kierrätyspuun käytössä sovelletaan jätteenpoltto-asetusta. Jätteenpolttoasetus määrää tiukemmat päästöjen raja-arvot rinnakkaispoltolle kuin hakkeen ja turpeen poltolle sekä jatkuvatoimiset savukaasujen mittauslaitteet. Rinnakkaispolton hiukkasmaisten päästöjen tiukempi raja-arvo vaatii tehokkaamman sähkösuodattimen. Lisäksi kierrätyspuuta käytettäessä tulistimen materiaaliin tulee olla kestävämpää, mikä aiheuttaa huomattavan lisäinvestoinnin. Työn päätavoitteena oli selvittää, onko kierrätyspuun käyttö taloudellisesti kannattavaa. Oletetulla kierrätyspuun hinnalla 10 €/MWh kierrätyspuuta polttavan voimalaitoksen takaisinmaksuaika on sama kuin haketta polttavan laitoksen ja vuoden lyhyempi kuin turvetta polttavan laitoksen. Tulokseksi saatiin, että rinnakkaispoltto käyttö on taloudellisesti kannattavaa hakkeenpolttoon nähden jos kierrätyspuun hinta on alle 11,2 €/MWh. Kierrätyspuun polttoon liittyy toiminnallinen riski, koska vastaavanlaisia rinnakkaispolttolaitoksia ei ole aiemmin rakennettu.

Tuhkalannoitteiden fosforin pidättyminen turpeeseen : miksi pidättyminen on tehokasta turpeen huonosta sitomiskyvystä huolimatta?

Seloste artikkelista: Phosphorus allocation in surface soil of two drained peatland forests following wood and peat ash application : why effective adsorption on low sorptive soils? Silva Fennica 41 (2007) : 3, s. 395-407.

Harvennuksen ja lannoituksen vaikutus kuusen puuaineen ja kuitujen ominaisuuksiin : tuloksia pitkään seuratuilta kenttäkokeilta

Seloste väitöskirjasta: The effects of thinning and fertilisation on wood and tracheid properties of Norway spruce (Picea abies) : the results of long-term experiments. Dissertationes Forestales 55.

Männyn kasvun ja puuaineen ominaisuuksien sekä saheiden laadun mallintaminen liittyen metsänhoitoon

Selostus väitöskirjasta: Modelling the growth and properties of stem and wood of Scots pine (Pinus sylvestris L.) as related to silvicultural management with implications for sawing yield and properties of sawn pieces. Dissertationes Forestales 65.