Optimization of the procedure for removing iron deposits on ceramic filter media

In this thesis, cleaning of ceramic filter media was studied. Mechanisms of fouling and dissolution of iron compounds, as well as methods for cleaning ceramic membranes fouled by iron deposits were studied in the literature part. Cleaning agents and different methods were closer examined in the experimental part of the thesis. Pyrite is found in the geologic strata. It is oxidized to form ferrous ions Fe(II) and ferric ions Fe(III). Fe(III) is further oxidized in the hydrolysis to form ferric hydroxide. Hematite and goethite, for instance, are naturally occurring iron oxidesand hydroxides. In contact with filter media, they can cause severe fouling, which common cleaning techniques competent enough to remove. Mechanisms for the dissolution of iron oxides include the ligand-promoted pathway and the proton-promoted pathway. The dissolution can also be reductive or non-reductive. The most efficient mechanism is the ligand-promoted reductive mechanism that comprises two stages: the induction period and the autocatalytic dissolution.Reducing agents(such as hydroquinone and hydroxylamine hydrochloride), chelating agents (such as EDTA) and organic acids are used for the removal of iron compounds. Oxalic acid is the most effective known cleaning agent for iron deposits. Since formulations are often more effective than organic acids, reducing agents or chelating agents alone, the citrate¿bicarbonate¿dithionite system among others is well studied in the literature. The cleaning is also enhanced with ultrasound and backpulsing.In the experimental part, oxalic acid and nitric acid were studied alone andin combinations. Also citric acid and ascorbic acid among other chemicals were tested. Soaking experiments, experiments with ultrasound and experiments for alternative methods to apply the cleaning solution on the filter samples were carried out. Permeability and ISO Brightness measurements were performed to examine the influence of the cleaning methods on the samples. Inductively coupled plasma optical emission spectroscopy (ICP-OES) analysis of the solutions was carried out to determine the dissolved metals.

Kaivosteollisuudessa syntyvän kipsin hyödyntäminen

Diplomityön tarkoituksena oli tutkia ja kehittää käyttökohde kaivosteollisuudessa syntyvälle märälle kipsisivuvirralle, joka sisältää metalliepäpuhtauksina alumiinia, rautaa ja mangaania ja jonka määrä on noin 1 000 000 t/a. Kirjallisuuden pohjalta tutkittiin aluksi mahdollisuutta hyödyntää kipsiaines asfaltti- ja sementtiteollisuuden raaka-aineena. Sementin joukkoon lisätään tavallisesti noin 5 p-% kipsiä, mutta harvinaisimpiin sementtilaatuihin sitä voidaan lisätä jopa 30 p-%. Tästä huolimatta vain pieni osa tutkimuksen kohteessa syntyvästä kipsisivuvirrasta voitaisiin hyödyntää tässä sovelluksessa. Lisäksi kipsisivuvirran sisältämät epäpuhtaudet täytyisi poistaa tai saattaa inaktiiviseen muotoon. Myöskään sen kosteuspitoisuus ei saisi olla suuri. Näin ollen tämän kipsisivuvirran hyödyntäminen asfaltti- ja sementtiteollisuuden lisäaineena ei ole mahdollista Seuraavaksi harkittiin kipsin kierrättämistä, jolloin yhtenä vaihtoehtona oli hajottaa kipsi termisesti rikkioksideiksi ja valmistaa niistä rikkihappoa. Taloudellisista syistä hajoamistuotteen on oltava rikkitrioksidia, josta voitaisiin veteen imeyttämällä valmistaa rikkihappoa. Kipsin hajottaminen termovaa´alla osoitti, että kipsi vaatii noin 1400 ºC:n lämpötilan ja haihtuvat komponentit ovat H2O, SO ja SO2, muttei SO3. Alempien oksidien muuttaminen rikkihapoksi vaatisi katalyyttisen hapetuksen, mikä olisi käytännössä liian kallista. Toisena vaihtoehtona kipsin kierrättämiseksi tutkittiin sen biologista pelkistämistä rikkivedyksi ja kalsiumhydroksidilietteeksi. Laboratoriossa Ca(OH)2-lietteestä valmistettiin hiilidioksidin avulla kalsiumkarbonaattia, jolloin päästiin 90 %:n kalsiumhydroksidin konversiossa. Lisäksi alumiinihydroksidi saatiin erotettua kipsilietteestä kokeellisesti hydrosyklonin avulla. Diplomityössä päädyttiin siihen, että sulfaatin biologinen pelkistäminen ja alumiinihydroksidin mekaaninen erotus jatkuvatoimisesti on varteenotettava vaihtoehto kipsisivuvirran hyödyntämiseksi.

Calcination of aluminum hydroxide over pressure and residence time

This work investigates the possible effect of pressure and residence time to the reaction of aluminum hydroxide into aluminum oxide. Various pressurized conditions are used as well as the help of various residence times. The aim is to increase the conversion of the reaction with the use of different pressures and residence times. The tests were performed with a laboratory scale fluidized bed reactor at the Outotec R&D Center in Frankfurt. Additional test work such as particle size analysis and differential thermal analysis were also carried out. Some calcined samples were also characterized with X-ray diffraction at the University of Auckland to obtain a reaction pathway when using pressurized conditions. All of the results are then compared with previous results.

Metallien talteenotto kloridiliuoksesta

Diplomityön tarkoituksena oli tutkia ja kehittää menetelmä arvometallien kuten kuparin, sinkin, koboltin ja nikkelin talteenottoon metallikloridiliuoksesta. Tavoitteena oli valita taloudellisin ja ympäristöystävällisin menetelmä, jolla saadaan nämä arvometallit myyntituotteiksi. Lisäksi puhdistetun prosessiveden tuli täyttää asetetut tavoitteet. Kirjallisuustyön perusteella laskettiin viidelle eri prosessivaihtoehdolle ainetaseet HSC Sim 6.0 ohjelmalla, joka on HSC Chemistry-pohjainen prosessien simulointi- ja mallinnusohjelma. Kaikissa vaihtoehdoissa oli ensimmäisenä prosessiosana kuparin, sinkin, koboltin ja nikkelin sulfidisaostus ja sakan pesu. Sulfidisaostusta seurasi vaihtoehtoisesti joko 1) hapetus hapella ja hydroksidisaostus, 2) hapetus vetyperoksidilla ja hydroksidisaostus, 3) pelkkä hydroksidisaostus, 4) hapetus SO2/O2-kaasuseoksella ja hydroksidisaostus tai 5) karbonaattisaostus. Taselaskennan perusteella valittiin kokeelliseen osaan tutkittavat prosessivaihtoehdot, jotka olivat sulfidisaostus, hydroksidisaostus, SO2/O2- hapetus ja hydroksidisaostus sekä karbonaattisaostus. Kokeissa arvometallit saatiin talteenotettua sulfidisaostuksella selektiivisimmin lämpötilassa 55 °C ja pH:ssa 4. Näissä olosuhteissa reagenssin kulutus verrattaessa muihin tehtyihin sulfidisaostuksiin oli pienin. Sakka laskeutui ja suotautui hyvin. Loppusakan sisältämien metallien (kupari, sinkki ja koboltti) pitoisuudet olivat korkeimmat. Myös nikkelin määrä oli suuri. Mangaani ja rauta saatiin talteenotettua selektiivisimmin karbonaattisaostuksella lämpötilassa 65 °C. Sakka sisälsi eniten mangaania. Sakka laskeutui ja suotautui hyvin. Tällä menetelmällä puhdistetun prosessiveden laatu täytti asetetut tavoitteet.

Paineviemärissä muodostuvan rikkivedyn vähentäminen kemikaloimalla

Anaerobisissa olosuhteissa muodostuva rikkivetykaasu on tyypillinen ongelma etenkin pitkillä paineviemäriosuuksilla. Sille ominainen epämiellyttävä haju aiheuttaa jätevedenkäsittelyverkostoissa ja viemärilinjojen lähialueilla merkittäviä hajuongelmia. Lisäksi rikkivedyn hapettuessa rikkihapoksi viemäri joutuu alttiiksi korroosiolle. Helsingin Etelä rannassa sijaitsevaan Munkkisaareen päätyy 4,4 km pitkä paineviemäri. Viemärin tuuletusputken kautta leviävä rikkivety on aiheuttanut hajuongelmia alueella. Korkeimmat mitatut rikkivetypitoisuudet tuuletusputken läheisyydessä olivat jopa 300 ppm. Tutkimuksessa tehtiin koeajoja erilaisilla hajunpoistokemikaaleilla rikkivetyongelman ratkaisemiseksi. Viemäriin annosteltiin sen alkupäässä jatkuvatoimisesti ferrosulfaattia ja ferrinitraattisulfaattia, sekä shokki-käsittelyllä natriumhydroksidia (lipeää). Munkkisaaressa mitatut rikkivetypitoisuudet osoittivat käytettyjen kemikaalien tehokkuuden rikkivedyn poistossa. Rikkivedyn saostamiseen tarkoitetut rautasuolat (ferrosulfaatti ja ferrinitraattisulfaatti) vähensivät 100 - 150 g annoksilla rikkivetyä yli 90 prosenttia. Natriumhydroksin annoksella 3600 g/m³ viemärin mikrobiologinen toiminta voitiin estää keskimäärin kymmeneksi päiväksi, mutta tehokas rikkivedyn muodostumisen esto vaatisi käsittelyn uusimisen noin 5 päivän välein. Normaaleissa viemärin olosuhteissa rikkivetyä muodostui vuorokauden aikana yhtä neliömetriä kohden noin 10 g. Kemikaalikäsittelyjen avulla muodostuminen aleni parhaimmillaan kymmenesosaan alkuperäisestä. Tulosten perusteella kemikaalien käytöllä viemärissä voisi välttyä kalliilta saneeraukselta Munkkisaaressa sekä muissa korroosiolle alttiiksi joutuvissa viemäreissä. Kemikalointikustannukset rautasuoloilla olivat noin 11 000 - 34 000 € ja lipeällä noin 7 000 € vuodessa.

Role of oxidation-reduction cycle of iron in direct leaching of zinc concentrate

Direct leaching is an alternative to conventional roast-leach-electrowin (RLE) zinc production method. The basic reaction of direct leach method is the oxidation of sphalerite concentrate in acidic liquid by ferric iron. The reaction mechanism and kinetics, mass transfer and current modifications of zinc concentrate direct leaching process are considered. Particular attention is paid to the oxidation-reduction cycle of iron and its role in direct leaching of zinc concentrate, since it can be one of the limiting factors of the leaching process under certain conditions. The oxidation-reduction cycle of iron was experimentally studied with goal of gaining new knowledge for developing the direct leaching of zinc concentrate. In order to obtain this aim, ferrous iron oxidation experiments were carried out. Affect of such parameters as temperature, pressure, sulfuric acid concentration, ferrous iron and copper concentrations was studied. Based on the experimental results, mathematical model of the ferrous iron oxidation rate was developed. According to results obtained during the study, the reaction rate orders for ferrous iron concentration, oxygen concentration and copper concentration are 0.777, 0.652 and 0.0951 respectively. Values predicted by model were in good concordance with the experimental results. The reliability of estimated parameters was evaluated by MCMC analysis which showed good parameters reliability.

Epäpuhtauksien poistaminen prosessivesistä

Kemira Chemicals Oy in Äetsä produces sodium chlorate as its main product. It is produced with electrolysis in electrolyte cells. During the manufacturing process impurities, out of which the largest one is iron, accumulate in the cells. These impurities are removed in cell wash with hydrochloric acid liquid, after which the wash water is precipitated with sodium hydroxide and sodium carbonate, and filtered with filter press. After the treatment the wash water is recycled back to the manufacturing process. The aim of this thesis was primarily to improve the treatment of wash water in order to remove the impurities with low costs. This would result in more impurity-free water and in sufficient capacity of impurity removal. The second aim was to maintain the chromium in the treated wash water because it forms a diaphragm of chromium hydroxide to cathode which prevents the flow of anions to cathode. The literature part investigates properties, use and manufacturing of sodium chlorate, electrolyte cell and its wash technique, and impurities of wash water. The beginning of the applied part investigates alternatives of separation methods which could be used to improve the treatment of wash water. In the experiments an optimum pH for the precipitation of wash water was determined, and a research of the use of sodium hydroxide, sodium carbonate, calcium hydroxide and calcium chloride as a precipitant was carried out. Also a suitable flocculant and a filter cloth for the treatment of wash water were determined. Finally, process changes were introduced, partly by applying the current equipment, and the costs and savings were calculated.

Mössbauer spectra of iron oxides in the bulk and nanocrystalline states

Magnetic nanoparticles are very important in modern industry. These particles are used in many different spheres of life. Nanoparticles have unusual physical and chemical properties connected both with quantum dimensional effects and with the increased role of the surface atoms. Most clearly the difference between the properties of bulk materials and nanoparticles can be seen in the magnetic properties of these materials. The most typical magnetic properties of nanomaterials are superparamagnetism with the size of the cluster from 1 to 10 nm; single-domain magnetic state of nanoclusters and nanostructures up to 20 nm; magnetization processes connected with magnetic cluster ordering and with its forms and sizes; quantum magnetic tunneling effects when magnetization changes by jumps and giant magnetoresistance effects. For research of the magnetic properties of iron-containing nanostructures, it is convenient to apply Mӧssbauer spectroscopy. In this work a number of nano-sized samples of iron oxides were examined by Mössbauer spectroscopy. The Mössbauer spectra of nanoparticles with various sizes were obtained. Mössbauer spectra of iron oxide nanoparticles were compared with the spectra of bulk samples. It was shown how the spectra of iron oxide nanoparticles change depending on the particle sizes.

Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Quasiclassical Approach to the Vortex State in Iron-based Superconductors

The quasiclassical approach was applied to the investigation of the vortex properties in the ironbased superconductors. The special attention was paid to manifestation of the nonlocal effects of the vortex core structure. The main results are as follows: (i) The effects of the pairing symmetries (s+ and s₊₊) on the cutoff parameter of field distribution, ξh, in stoichiometric (like LiFeAs) and nonstoichiometric (like doped BaFe₂As₂) iron pnictides have been investigated using Eilenberger quasiclassical equations. Magnetic field, temperature and impurity scattering dependences of ξh have been calculated. Two opposite behavior have been discovered. The ξh /ξc2 ratio is less in s+ symmetry when intraband impurity scattering (Γ₀) is much larger than one and much larger than interband impurity scattering (Γπ), i.e. in nonstoichiometric iron pnictides. Opposite, the value ξh /ξc2 is higher in s+ case and the field dependent curve is shifted upward from the "clean" case (Γ₀ = Γπ = 0) for stoichiometric iron pnictides (Γ₀ = Γπ ≪ 1). (ii) Eilenberger approach to the cutoff parameter, ξh, of the field distribution in the mixed state of high

Acidic dissolution of iron oxides and regeneration of a ceramic filter medium

The dewatering of iron ore concentrates requires large capacity in addition to producing a cake with low moisture content. Such large processes are commonly energy intensive and means to lower the specific energy consumption are needed. Ceramic capillary action disc filters incorporate a novel filter medium enabling the harnessing of capillary action, which results in decreased energy consumption in comparison to traditional filtration technologies. As another benefit, the filter medium is mechanically and chemically more durable than, for example, filter cloths and can, thus, withstand harsh operating conditions and possible regeneration better than other types of filter media. In iron ore dewatering, the regeneration of the filter medium is done through a combination of several techniques: (1) backwashing, (2) ultrasonic cleaning, and (3) acid regeneration. Although it is commonly acknowledged that the filter medium is affected by slurry particles and extraneous compounds, published research, especially in the field of dewatering of mineral concentrates, is scarce. Whereas the regenerative effect of backwashing and ultrasound are more or less mechanical, regeneration with acids is based on chemistry. The chemistry behind the acid regeneration is, naturally, dissolution. The dissolution of iron oxide particles has been extensively studied over several decades but those studies may not necessarily be directly applicable in the regeneration of the filter medium which has undergone interactions with the slurry components. The aim of this thesis was to investigate if free particle dissolution indeed correlates with the regeneration of the filter medium. For this purpose, both free particle dissolution and dissolution of surface adhered particles were studied. The focus was on acidic dissolution of iron oxide particles and on the study of the ceramic filter medium used in the dewatering of iron ore concentrates. The free particle dissolution experiments show that the solubility of synthetic fine grained iron oxide particles in oxalic acid could be explained through linear models accounting for the effects of temperature and acid concentration, whereas the dissolution of a natural magnetite is not so easily explained by such models. In addition, the kinetic experiments performed both support and contradict the work of previous authors: the suitable kinetic model here supports previous research suggesting solid state reduction to be the reaction mechanism of hematite dissolution but the formation of a stable iron oxalate is not supported by the results of this research. Several other dissolution mechanisms have also been suggested for iron oxide dissolution in oxalic acid, indicating that the details of oxalate promoted reductive dissolution are not yet agreed and, in this respect, this research offers added value to the community. The results of the regeneration experiments with the ceramic filter media show that oxalic acid is highly effective in removing iron oxide particles from the surface of the filter medium. The dissolution of those particles did not, however, exhibit the expected behaviour, i.e. complete dissolution. The results of this thesis show that although the regeneration of the ceramic filter medium with acids incorporates the dissolution of slurry particles from the surface of the filter medium, the regeneration cannot be assessed purely based upon free particle dissolution. A steady state, dependent on temperature and on the acid concentration, was observed in the dissolution of particles from the surface even though the limit of solubility of free iron oxide particles had not been reached. Both the regeneration capacity and efficiency, with regards to the removal of iron oxide particles, was found to be temperature dependent, but was not affected by the acid concentration. This observation further suggests that the removal of the surface adhered particles does not follow the dissolution of free particles, which do exhibit a dependency on the acid concentration. In addition, changes in the permeability and in the pore structure of the filter medium were still observed after the bulk concentration of dissolved iron had reached a steady state. Consequently, the regeneration of the filter medium continued after the dissolution of particles from the surface had ceased. This observation suggests that internal changes take place at the final stages of regeneration. The regeneration process could, in theory, be divided into two, possibly overlapping, stages: (1) dissolution of surface-adhered particles, and (2) dissolution of extraneous compounds from within the pore structure. In addition to the fundamental knowledge generated during this thesis, tools to assess the effects of parameters on the regeneration of the ceramic filter medium are needed. It has become clear that the same tools used to estimate the dissolution of free particles cannot be used to estimate the regeneration of a filter medium unless only a robust characterisation of the order of regeneration efficiency is needed.

CO2 sparging for improving the filtration properties of iron ore slurries

Iron ore treatment processes are usually continuous and high tonnage and filtration equipment has to meet these requirements. In magnetite (Fe3O4) treatment process continuous rotary disc filters are often used for filtration. Carbon dioxide (CO2) treatment is a fairly novel and un-known filtration enhancing process. The interest to use CO2 is quite high because CO2 is a greenhouse gas that is abundant, readily available and capture and use of CO2 would be environmentally beneficial. The focus of this thesis was to investigate if CO2 could be used to enhance the filtration of magnetite with ceramic disc filter. Previous studies have suggested that CO2 could be used to enhance the filtration properties of different iron ores thus increasing the filtration capacity. In the literature part, the basic theory of filtration and the particle properties affecting filtration were discussed. The basic steps of a typical ore treatment process were presented. The reasons why CO2 might enhance the filtration properties of different ores were investigated. A literature survey of earlier studies of CO2 addition as a filter aid was presented and the basic chemical properties and reactions of CO2 were also discussed. The experimental part was done at the LUT Laboratory of Separation Technology using different magnetite samples from the industry. The filtration experiments indicated that CO2 had a positive influence on the filtration properties of magnetite slurry. Zeta potential of untreated and CO2 treated magnetite was measured and CO2 treated magnetite had lower zeta potential values than the untreated magnetite. The filtration capacity was increased while the cake moisture levels were only slightly increased.

Development of an environmentally friendly method of starch oxidation by hydrogen peroxide and a complex water-soluble Iron catalyst

Oxidized starch is a key component in the paper industry, where it is used as both surfacing sizer and filler. Large quantities are annually used for this purpose; however, the methods for the oxidation are not environmentally friendly. In our research, we have studied the possibility to replace the harmful oxidation agents, such as hypochlorite or iodates and transition metal catalysts, with a more environmentally friendly oxidant, hydrogen peroxide (H2O2), and a special metal complex catalyst (FePcS), of which only a small amount is needed. The work comprised batch and semi-batch studies by H2O2, ultrasound studies of starch particles, determination of low-molecular by-products and determination of the decomposition kinetics of H2O2 in the presence of starch and the catalyst. This resulted in a waste-free oxidation method, which only produces water and oxygen as side products. The starch oxidation was studied in both semi-batch and batch modes in respective to the oxidant (H2O2) addition. The semi-batch mode proved to yield a sufficient degree of substitution (COOH groups) for industrial purposes. Treatment of starch granules by ultrasound was found to improve the reactivity of starch. The kinetic results were found out to have a rather complex pattern – several oxidation phases were observed, apparently due to the fact that the oxidation reaction in the beginning only took place on the surface, whereas after a prolonged reaction time, partial degradation of the solid starch granules allowed further reaction in the interior parts. Batch-mode experiments enabled a more detailed study of the mechanisms of starch in the presence of H2O2 and the catalyst, but yielded less oxidized starch due to rapid decomposition of H2O2 due to its high concentrations. The effect of the solid-liquid (S/L) ratio in the reaction system was studied in batch experiments. These studies revealed that the presence of the catalyst and the starch enhance the H2O2 decomposition.

Electrochemical Treatment of Wastewaters

Electrocoagulation is a process in which wastewater is treated under electrical current. Coagulant is formed during the process through the metal anode dissolution to respective ions which react with hydroxyl ions released in cathode. These metal hydroxides form complexes with pollutant ions. Pollutants are removed among metal hydroxide precipitates. This study was concentrated on describing chemistry and device structures in which electrochemical treatment operations are based on. Studied pollutants were nitrogen compounds, sulphate, trivalent and pentavalent arsenic, heavy metals, phosphate, fluoride, chloride, and bromide. In experimental part, removal of ammonium, nitrate, and sulphate during electrochemical treatment was studied separately. Main objective of this study was to find suitable metal plate material for ammonium, nitrate, and sulphate removal, respectively. Also other parameters such as pH of solution, concentration of pollutant and sodium chloride, and current density were optimized. According to this study the most suitable material for ammonium and sulphate removal by electrochemical treatment was stainless steel. Respectively, iron was the optimum material for nitrate removal. Rise in the pH of solution at the final stage of electrochemical treatment of ammonium, nitrate, and sulphate was detected. Conductivities of solutions decreased during ammonium removal in electrochemical processes. When nitrate and sulphate were removed electrochemically conductivities of solutions increased. Concentrations of residual metals in electrochemically treated solutions were not significant. Based on this study electrochemical treatment processes are recommended to be used in treatment of industrial wastewaters. Treatment conditions should be optimized for each wastewater matrix.

Magnesium hydroxide-based peroxide bleaching of high-brightness mechanical pulps

A high final brightness is desired in most paper and board products. This requires bleaching processes that are able to produce high-brightness pulps. Mechanical pulps are widely bleached for high brightness using alkaline hydrogen peroxide with traditional sodium hydroxide and sodium silicate as additives. With high doses however, peroxide bleaching causes high organic loads in the mill effluent and anionic trash carry-over to papermaking. To alleviate the problems that arise from the use of sodium-based additives in peroxide bleaching, interest in the use of alternative magnesium-based chemicals has increased. In this study, a new, technical high-purity magnesium hydroxide-based bleaching additive was evaluated on laboratory-scale, pilot-scale and mill-scale experiments and trials for its ability to produce a high brightness in peroxide bleaching without the known problems of sodium-based chemicals. The key findings of this study include: a high brightening potential of peroxide bleaching using the Mg(OH)2-based additive, significant reductions (40-70%) in all categories of environmental load, and cationic demand lowered by 60-70% in bleached pulp with no loss in strength properties or in sheet bulk. When used in TMP refiner bleaching, the Mg(OH)2-based additive resulted in savings in specific energy consumption and provided a good bleaching response.