Pretreatment processes in gold recovery by thiosulphate leaching

This thesis describes several different pretreatment processes for gold concentrates and ores. The thesis is divided to theoretical part and experimental part. The theoretical part presents the operating principle of the main pretreatment methods and their suitability for thiosulphate leaching. In the theoretical part also the whole recovery process for gold from ore to elemental gold is presented. In the experimental part the study is focused on pretreatment of sulphidic refractory concentrates with mechanical activation and chemical oxidation under alkaline environment; and their effect on leachability in the thiosulphate leaching. In the experimental part a combined 2-step process, where chemical oxidation under ammoniacal environment is cascaded with thiosulphate leaching in the same conditions, is also tested. The main sulphuric mineral components in the studied refractory concentrate are pyrite (49.4 %) and arsenopyrite (27.7 %). The gold content in the concentrate is 11.3 ppm and silver content is 90 ppm. Without pretreatment the gold conversion in thiosulphate leaching was 30 %, which was analyzed at the time point of 9 hours. At that time the silver conversion was 17 %. By using mechanical activation the gold conversion reached was 59 % and silver conversion 26 %. With chemical oxidation under alkaline environment, where the used chemical was sodium hydroxide, the reached conversion of gold was 72 % and 31 % for silver. In the combined oxidation and leaching experiment the conversion of gold remained at 49 % and 18 % for silver.

Improving the competitiveness of electrolytic Zinc process by chemical reaction engineering approach

This doctoral thesis describes the development work performed on the leachand purification sections in the electrolytic zinc plant in Kokkola to increase the efficiency in these two stages, and thus the competitiveness of the plant. Since metallic zinc is a typical bulk product, the improvement of the competitiveness of a plant was mostly an issue of decreasing unit costs. The problems in the leaching were low recovery of valuable metals from raw materials, and that the available technology offered complicated and expensive processes to overcome this problem. In the purification, the main problem was consumption of zinc powder - up to four to six times the stoichiometric demand. This reduced the capacity of the plant as this zinc is re-circulated through the electrolysis, which is the absolute bottleneck in a zinc plant. Low selectivity gave low-grade and low-value precipitates for further processing to metallic copper, cadmium, cobalt and nickel. Knowledge of the underlying chemistry was poor and process interruptions causing losses of zinc production were frequent. Studies on leaching comprised the kinetics of ferrite leaching and jarosite precipitation, as well as the stability of jarosite in acidic plant solutions. A breakthrough came with the finding that jarosite could precipitate under conditions where ferrite would leach satisfactorily. Based on this discovery, a one-step process for the treatment of ferrite was developed. In the plant, the new process almost doubled the recovery of zinc from ferrite in the same equipment as the two-step jarosite process was operated in at that time. In a later expansion of the plant, investment savings were substantial compared to other technologies available. In the solution purification, the key finding was that Co, Ni, and Cu formed specific arsenides in the “hot arsenic zinc dust” step. This was utilized for the development of a three-step purification stage based on fluidized bed technology in all three steps, i.e. removal of Cu, Co and Cd. Both precipitation rates and selectivity increased, which strongly decreased the zinc powder consumption through a substantially suppressed hydrogen gas evolution. Better selectivity improved the value of the precipitates: cadmium, which caused environmental problems in the copper smelter, was reduced from 1-3% reported normally down to 0.05 %, and a cobalt cake with 15 % Co was easily produced in laboratory experiments in the cobalt removal. The zinc powder consumption in the plant for a solution containing Cu, Co, Ni and Cd (1000, 25, 30 and 350 mg/l, respectively), was around 1.8 g/l; i.e. only 1.4 times the stoichiometric demand – or, about 60% saving in powder consumption. Two processes for direct leaching of the concentrate under atmospheric conditions were developed, one of which was implemented in the Kokkola zinc plant. Compared to the existing pressure leach technology, savings were obtained mostly in investment. The scientific basis for the most important processes and process improvements is given in the doctoral thesis. This includes mathematical modeling and thermodynamic evaluation of experimental results and hypotheses developed. Five of the processes developed in this research and development program were implemented in the plant and are still operated. Even though these processes were developed with the focus on the plant in Kokkola, they can also be implemented at low cost in most of the zinc plants globally, and have thus a great significance in the development of the electrolytic zinc process in general.

The leaching of nutrients from ash- and PK-fertilised peat

Tiivistelmä: ravinteiden huuhtoutuminen tuhka- ja PK-lannoitetusta turpeesta

Timing incorporation of different green manure crops to minimize the risk of nitrogen leaching

Selostus: Viherlannoituskasvuston kynnön viivyttäminen vähentää typen huuhtoutumista

Undersowing Italian ryegrass diminishes nitrogen leaching from spring barley

Selostus: Italian raiheinä aluskasvina vähentää typen huuhtoutumista ohranviljelyssä

Seasonal dry deposition and canopy leaching of base cations in a subtropical evergreen mixed forest, China

Abstract

Temporal trends in chemical parameters of upland forest soils in southern Finland

Abstract

Development of Craniofacial Bone Defect Reconstruction Implant Based on Fibre-Reinforced Composite with Photopolymerisable Resin Systems. Experimental studies in vitro and in vivo.

Reconstruction of defects in the craniomaxillofacial (CMF) area has mainly been based on bone grafts or metallic fixing plates and screws. Particularly in the case of large calvarial and/or craniofacial defects caused by trauma, tumours or congenital malformations, there is a need for reliable reconstruction biomaterials, because bone grafts or metallic fixing systems do not completely fulfill the criteria for the best possible reconstruction methods in these complicated cases. In this series of studies, the usability of fibre-reinforced composite (FRC) was studied as a biostable, nonmetallic alternative material for reconstructing artificially created bone defects in frontal and calvarial areas of rabbits. The experimental part of this work describes the different stages of the product development process from the first in vitro tests with resin-impregnated fibrereinforced composites to the in vivo animal studies, in which this FRC was tested as an implant material for reconstructing different size bone defects in rabbit frontal and calvarial areas. In the first in vitro study, the FRC was polymerised in contact with bone or blood in the laboratory. The polymerised FRC samples were then incubated in water, which was analysed for residual monomer content by using high performance liquid chromatography (HPLC). It was found that this in vitro polymerisation in contact with bone and blood did not markedly increase the residual monomer leaching from the FRC. In the second in vitro study, different adhesive systems were tested in fixing the implant to bone surface. This was done to find an alternative implant fixing system to screws and pins. On the basis of this study, it was found that the surface of the calvarial bone needed both mechanical and chemical treatments before the resinimpregnated FRC could be properly fixed onto it. In three animal studies performed with rabbit frontal bone defects and critical size calvarial bone defect models, biological responses to the FRC implants were evaluated. On the basis of theseevaluations, it can be concluded that the FRC, based on E-glass (electrical glass) fibres forming a porous fibre veil enables the ingrowth of connective tissues to the inner structures of the material, as well as the bone formation and mineralization inside the fibre veil. Bone formation could be enhanced by using bioactive glass granules fixed to the FRC implants. FRC-implanted bone defects healed partly; no total healing of defects was achieved. Biological responses during the follow-up time, at a maximum of 12 weeks, to resin-impregnated composite implant seemed to depend on the polymerization time of the resin matrix of the FRC. Both of the studied resin systems used in the FRC were photopolymerised and the heat-induced postpolymerisation was used additionally.

Effect of physico-chemical conditions and operating parameters on flux and retention of different components in ultrafiltration and nanofiltration fractionation of sweet whey

Tässä väitöstutkimuksessa tutkittiin fysikaaliskemiallisten olosuhteiden ja toimintaparametrien vaikutusta juustoheran fraktiointiin. Kirjallisuusosassa on käsitelty heran ympäristövaikutusta, heran hyödyntämistä ja heran käsittelyä kalvotekniikalla. Kokeellinen osa on jaettu kahteen osaan, joista ensimmäinen käsittelee ultrasuodatusta ja toinen nanosuodatusta juustoheran fraktioinnissa. Ultrasuodatuskalvon valinta tehtiin perustuen kalvon cut-off lukuun, joka oli määritetty polyetyleeniglykoliliuoksilla olosuhteissa, joissa konsentraatiopolariosaatioei häiritse mittausta. Kriittisen vuon konseptia käytettiin sopivan proteiinikonsentraation löytämiseksi ultrasuodatuskokeisiin, koska heraproteiinit ovat tunnetusti kalvoa likaavia aineita. Ultrasuodatuskokeissa tutkittiin heran eri komponenttien suodattumista kalvon läpi ja siihen vaikuttavia ominaisuuksia. Herapermeaattien peptidifraktiot analysoitiin kokoekskluusiokromatografialla ja MALDI-TOF massaspektrometrillä. Kokeissa käytettävien nanosuodatuskalvojen keskimääräinen huokoskoko analysoitiin neutraaleilla liukoisilla aineilla ja zeta-potentiaalit virtauspotentiaalimittauksilla. Aminohappoja käytettiin malliaineina tutkittaessa huokoskoon ja varauksen merkitystä erotuksessa. Aminohappojen retentioon vaikuttivat pH ja liuoksen ionivahvuus sekä molekyylien väliset vuorovaikutukset. Heran ultrasuodatuksessa tuotettu permeaatti, joka sisälsi pieniä peptidejä, laktoosia ja suoloja, nanosuodatettiin happamassa ja emäksisessä pH:ssa. Emäksisissä oloissa tehdyssä nanosuodatuksessa foulaantumista tapahtui vähemmän ja permeaattivuo oli parempi. Emäksisissä oloissa myös selektiivisyys laktoosin erotuksessa peptideistä oli parempi verrattuna selektiivisyyteen happamissa oloissa.

Practical applications of a systematic approach to the chemical abatement of pollutants in water and air

The present dissertation is devoted to the systematic approach to the development of organic toxic and refractory pollutants abatement by chemical decomposition methods in aqueous and gaseous phases. The systematic approach outlines the basic scenario of chemical decomposition process applications with a step-by-step approximation to the most effective result with a predictable outcome for the full-scale application, confirmed by successful experience. The strategy includes the following steps: chemistry studies, reaction kinetic studies in interaction with the mass transfer processes under conditions of different control parameters, contact equipment design and studies, mathematical description of the process for its modelling and simulation, processes integration into treatment technology and its optimisation, and the treatment plant design. The main idea of the systematic approach for oxidation process introduction consists of a search for the most effective combination between the chemical reaction and the treatment device, in which the reaction is supposed to take place. Under this strategy,a knowledge of the reaction pathways, its products, stoichiometry and kinetics is fundamental and, unfortunately, often unavailable from the preliminary knowledge. Therefore, research made in chemistry on novel treatment methods, comprisesnowadays a substantial part of the efforts. Chemical decomposition methods in the aqueous phase include oxidation by ozonation, ozone-associated methods (O3/H2O2, O3/UV, O3/TiO2), Fenton reagent (H2O2/Fe2+/3+) and photocatalytic oxidation (PCO). In the gaseous phase, PCO and catalytic hydrolysis over zero valent ironsare developed. The experimental studies within the described methodology involve aqueous phase oxidation of natural organic matter (NOM) of potable water, phenolic and aromatic amino compounds, ethylene glycol and its derivatives as de-icing agents, and oxygenated motor fuel additives ¿ methyl tert-butyl ether (MTBE) ¿ in leachates and polluted groundwater. Gas-phase chemical decomposition includes PCO of volatile organic compounds and dechlorination of chlorinated methane derivatives. The results of the research summarised here are presented in fifteenattachments (publications and papers submitted for publication and under preparation).

Fluoriditasetarkastelu ja päästöjen hallinta ferrokromi- ja terästeollisuudessa

Työn alkuosassa kartoitettiin AvestaPolarit –yhtiöiden Tornion tehtaiden keskeiset fluoridilähteet kuten fluspaatti, valukuonat, valupulverit ja fluorivetyhappo. Valupulverien ja kuonien haihtumis- ja liukoisuuskäyttäytymistä valaistiin kotimaisten ja kansainvälisten tutkimusten avulla. Tutkimustuloksia sovellettiin pääpiirteittäin Tornion tehtaiden tilanteeseen ottamalla huomioon tekijät, jotka saattoivat lieventää tai vahvistaa fluoridien vaikutusta ympäristöön. Yleisesti fluoridien ympäristö- ja terveysvaikutukset arvioitiin vähäisiksi. Työn kokeellisessa osassa määritettiin Tornion tehtaiden ferrokromitehtaan, terässulaton, kuumavalssaamon ja kylmävalssaamon fluoriditaseet. Jokaisen osastojen syötteiden fluoridipitoisuudet selvitettiin tuottajien ilmoittamien tuotekoostumuksien, spesifikaatioiden ja fluoridianalyysien perusteella. Fluoridien kokonaismäärät laskettiin jokaiselle syötteelle ja ne suhteutettiin kunkin osaston vuoden 2001 tuotantotasoon. Tasetarkastelussa suurimpina fluoridisyötteinä nousivat odotetusti esiin terässulaton käyttämä kuonanmuodostaja-aine fluspaatti (CaF2) ja kylmävalssaamon peittaushappo, 70 prosenttinen fluorivetyhappo (HF). Lisäksi muita merkittäviä syötteitä olivat kylmävalssaamon käyttämä kalkkipitoinen sekakuona ja ferrokromitehtaan sulatuskoksi. Tuotoksien eli päästöjen fluoridipitoisuudet saatiin selville päästömittauksin. Jätevesistä otettiin pääosin viikoittaisia kokoomanäytteitä, jotka analysoitiin tehtaan laboratoriossa. Kaasumaiset tuotokset oli määritetty kertamittauksien perusteella. Kiinteiden tuotoksien eli sakkojen ja kuonien fluoridimittaukset suoritettiin 3 sulatuksen kuonanäytteistä ja sakan vuosinäytteestä. Tuotoksista suurimmat ominaispäästökertoimet olivat juuri terässulaton AOD-konvertterin ja senkkauunin kuonilla ja kylmävalssaamon neutraloidulla regenerointisakalla ja neutralointisakoilla. Näistä ei aiheutunut varsinaista päästöä lähiympäristöön, koska sakat ja kuonat loppusijoitetaan tehtaan kaatopaikalle tai niitä käytetään liukenemattomassa muodossa. Tornion tehtaiden fluoridisyötteiden ja -tuotoksien mittausepätarkkuudet vaikuttivat fluoriditaseeseen. Ferrokromitehtaan fluoridisyötteet olivat kokonaismäärältään selvästi suurempia kuin tuotokset. Terässulaton fluoriditaseen tuotokset olivat suurempia kuin syötteet ja kylmävalssaamon syötteet sekä tuotokset olivat karkeasti arvioiden samaa suuruusluokkaa. Kuumavalssaamon fluoridisyötteet ja -tuotokset olivat mitättömiä. Fluoriditaseen epävarmuustekijöitä voidaan vähentää suorittamalla esimerkiksi useita fluoridimittauksia kaasumaisista päästöistä.