Mixing in rotating drums

Tämän diplomityön tarkoitus on parantaa meesauunin toiminnallista tehokkuutta tehostamalla lämmönsiirtoa. Lämmönsiirron parantamiseksi kehitetään erilaisia nostinratkaisuja. Kokeita suoritetaan käyttäen eri sekoitinratkaisuja ja erilaisia prosessiparametreja. Työn kirjallisuusosassa esitetään meesauuni sekä rumpumaisten uunien toiminta. Työssä selvitetään myös sekoituksen analysointiin käytettäviä tapoja ja laskukaavoja. Kirjallisuusosassa keskitytään myös rummussa tapahtuviin fysikaalisiin ilmiöihin sekä erilaisten fluidien reologiaan. Työn kokeellisessa osassa käytettiin LUT Kemiantekniikalla suunniteltua pilot -kokoluokan rumpu-uunia, jolla kokeitaan suoritettiin, käyttäen erilaisia sekoitinratkaisuja ja sekoitusprosessiparametreja. Kokeissa käytettiin myös eri viskositeetin omaavia materiaaleja. Valitut materiaalit olivat vesi, CMC (karboksimetyyliselluloosa) ja kiinteä meesa. Kokeiden tuloksena löydettiin nostinratkaisuja, joilla sekoittumista ja lämmönsiirtoa pystytään parantamaan sekä pidentämään viipymäaikaa.

Formation of polyelectrolyte multilayers and polyelectrolyte complexes in dual polymer treatment of papermaking pulp

The goal of this study was to find a new approach to modify chemically the properties of paper by improving fiber quality. This Master’s thesis includes the multiple polymer treatment in general and themeasurement methods with which the formation of multilayers and complexes can be noticed. The treatment by an oppositely charged dual polymer system is a good approach to increase paper strength. In this work, starch, a cationic polymer, and carboxymethyl cellulose (CMC), an anionic polymer, were used step-by-step to improve paper strength. The adsorption of cationic starch and CMC on cellulose fibers were analyzed via polyelectrolyte titration. The results showed that paper strength was enhanced slightly with a layer-by-layer assembly of the polymers. However, if the washing stage, which was required for layer-by-layer assembly, was eliminated, the starch/CMC complex was deposited on fibers more efficiently, and the paper strength was improved more significantly.

Linjasekoittimensekoituskyvyn määrittäminen

Työn tavoitteena oli kehittää sekoituskyvyn empiirinen monimuuttujafunktio eräälle dynaamiselle linjasekoittimelle. Monimuuttujafunktio oli tarkoitus kehittää sekoittimen kierrosnopeuden, virtaavien materiaalien ja tilavuusvirtausten perus-teella. Työn kirjallisuusosassa tarkasteltiin pääosin dynaamisia linjasekoittimia ja niiden toimintaperiaatteita sekä sekoituskyvyn määrittämiseen soveltuvia mittausmene-telmiä. Sekoitettavien aineiden epähomogeenisuus määritettiin mittaamalla termoelemen-teillä sekoittimen jälkeisen virran lämpötilavaihtelut. Sekoitettavina aineina käy-tettiin kolmea erilaista seosta: vesi-vesi-, kuitususpensio-vesi- ja karboksyylime-tyyliselluloosa-vesiseoksia. Muita muuttujia kokeissa olivat neljä eri sekoittimen kierrosnopeutta, neljä eri päävirran tilavuusvirtausta ja kolme päävirran sekäsii-hen lisättävän sivuvirran suhdetta. Monimuuttujafunktiokehitettiin vain kuitususpensio-vesiajojen pohjalta muilla seoksilla tehtyjen koeajojen osittaisen epäonnistumisen vuoksi. Hallitsevaksi pa-rametriksi monimuuttujafunktiossa osoittautui sekoittimen kierrosnopeus. Osittai-nen epäonnistuminen kokeissa johtui osaksi termoelementtien käytön sopimatto-muudesta sekoituskyvyn määrittämiseen ja osaksi sekoitettavien aineiden valin-nasta. Jatkotutkimuksiaajatellen muista sekoituskyvyn mittaamiseen käytettävissä olevista menetelmistäkäyttökelpoisimmaksi arvioitiin sähkötomografia.

Kalvosuodatusprosessin tehostaminen paperiteollisuuden sovelluksissa

Tässä diplomityössä tutkittiin kalvosuodatuksen esikäsittelymenetelmiä ja kalvonpesua. Työn kirjallisuusosassa käsitellään vuon alenemiseen vaikuttavia tekijöitä, esikäsittelymenetelmiä ja kalvonpesua. Kokeellisessa osassa tutkittiin kemiallisten esikäsittelyjen vaikutusta vuon alenemiseen paperitehtaan happaman kiertoveden kirkkaan suodoksen kalvosuodatuksessa. Esikäsittelykemikaalit olivat ympäristöystävällisiä ja paperinvalmistusprosessiin soveltuvia. Lisäksi tutkittiin kalvonpesuaineiden pesutehokkuuksia. Tutkitut esikäsittelyaineet olivat mikrokiteinen kitosaani, karboksimetyyliselluloosa, selluloosa- ja puukuitu sekä kaupallinen antiskalantti. Pesuaineista tutkittiin kolmea kaupallista kalvonpesuainetta, yhtä kalvopesun tehostusainetta sekä peretikkahappoa. Kokeet tehtiin kahdella laboratoriomittakaavaisella kalvosuodattimella. Kalvoina käytettiin kahta nanosuodatus- ja yhtä ultrasuodatuskalvoa. Vuon alenemista tutkittiin suodatuksen aikaisena alenemisena ja vesivuohon verrattavana alenemisena. Esikäsittelyjen vaikutusta erotustehokkuuteen tutkittiin ioni-, johtokyky-, orgaanisen hiilen kokonaispitoisuus-, sokeri-, sameus- ja ligniinireduktioilla. Lisäksi määritettiin kalvon likaantuminen suodatuksen aikana vesivuon määrityksillä ennen ja jälkeen suodatuksen. Pesutehokkuus määritettiin vesivuon määrityksillä suodatuksen jälkeen ja pesun jälkeen. Kitosaani- ja karboksimetyyliselluloosakäsittelyillä oli vuon alenemista estävä vaikutus hydrofiilisellä nanosuodatuskalvolla suodatettaessa. Kitosaanikäsittelyn 5 g/dm3:n ja karboksimetyyliselluloosakäsittelyn 2 g/ dm3:n annostuksella vuot alentuivat suodatuksen aikana 8 %-yksikköä vähemmän kuin ilman esikäsittelyä. Puukuitukäsittely stabiloi 0,1 g/dm3:n annostuksella saman kalvon vuota, kun kiintoainetta ei poistettu syötöstä. Hydrofobisen nanosuodatuskalvon vuon alenemista ehkäisivät puu- ja selluloosakuitukäsittelyt sekä karboksimetyyliselluloosakäsittely. Karboksimetyyliselluloosakäsittely vähensi vuon alenemista 25 %-yksikköä ja puukuitukäsittely 13 %-yksikköä. Hydrofiilisellä ultrasuodatuskalvolla vuon aleneminen oli pientä ilman esikäsittelyä. Reduktioihin esikäsittelyt vaikuttivat parhaiten ultrasuodatuskalvolla. Kitosaanikäsittely nosti 1 g/dm3:n annostuksella alumiinireduktion 50 %:sta 96 %:iin ja 5 g/dm3:n annostuksella rautareduktion 30 %:sta 55 %:iin. Karboksyylimetyyliselluloosakäsittelyt vaikuttivat parantavasti mangaanin, magnesiumin, raudan ja kalsiumin reduktioihin. Optimi karboksyylimetyyliselluloosa-annostus oli 2 g/dm3. Merkittävin reduktion nousu oli kalsiumilla, jonka reduktio nousi esikäsittelyllä 4 %:sta 57 %:iin. Reduktiota nostava mekanismi oli kalvon pinnalle muodostuva sekundaarikerros. Pesuaineista tehokkain oli entsyymiä sisältävä kalvonpesuaine. Suurin vaikutus sillä oli hydrofobisen nanosuodatuskalvon pesussa. Optimiannostuksella (0,5 %) kalvon vesivuo pesun jälkeen oli 114 % pesua edeltäneestä vesivuosta. Muut kaupalliset pesuaneet oli tehokkaita hydrofiilisille kalvoille. Peretikkahappo oli yksittäisenä pesuaineena heikkotehoinen.

Slurry flows in progressive cavity and in hose pumps

The aim of this thesis was to research how slurry’s viscosity and rheology affect to pumping in peristaltic hose pump and in eccentric progressive cavity pump. In addition, it was researched the formed pressure pulsation in hose pump. Pressure pulsation was studied by pumping different slurries and by using different pipe materials. Pressure and power curves were determined for both used pumps. It was also determined NPSHR curve for the progressive cavity pump. Literature part of the thesis considered to distribute fluids to different rheology types, as well as theories and models to identify different rheology types. Special attention was paid to non-Newtonian fluids, which were also used in experimental part of this thesis. In addition, the literature part discusses about pumps, parameters for pump sizing, and pressure pulsation in hose pump. Starch, bentonite, and carboxymethyl cellulose slurries were used in the experimental part of this thesis. The slurries were pumped with Flowrox peristaltic hose pump (LPP-T32) and eccentric progressive cavity pump (C10/10). From the each slurry was taken a sample, and the samples were analyzed for concentration, viscosity and rheology type. The used pipe materials in pressure pulsation experiments were steel and elastic, and it was also used a prototype of pulsation dampener. The pulsation experiments indicated that the elastic pipe and the prototype of pulsation dampener attenuated pressure pulsation better than the steel pipe at low pressure levels. The differences between different materials disappeared when pressure level and pump rotation speed increased. In slurry experiments, pulsation was different depending on rheology and viscosity of the slurry. According to experiments, the rheology did not significantly affect to pump power consumption or efficiency.

Rheological characterization of polysaccharide gels

In this Master’s Thesis work the rheological properties of different polysaccharide gels have been studied. The results of this study are used as a starting point for further investigations of potential applications. In order to understand rheological behavior of studied materials, the commercial hydrocolloids such as sodium carboxymethyl cellulose, xanthan gum and guar gum were used as reference and comparison material for rheological studies. As a part the rheological research the development and implementation of proper measurement methods for studied materials were carried out. In the literature review, short introductions of studied materials and application areas of rheological modifiers are summarized. In addition, basic rheological concepts and key fundamentals are explained. In the experimental part the focus was on the rheological characterization of aqueous suspensions of studied materials. Especially, gel strength and solution stability were investigated. The rheological measurements included both rotational and oscillatory measurements in different conditions, where several chemical and physical properties were measured with Anton Paar MCR302 dynamic rotational rheometer. Studied polysaccharide gels can be clearly defined to be shear thinning and thixotropic materials. They have strong gel forming properties even at low concentrations, which explains the superior thickening behavior for some of the samples. Along with rheological characterization of selected materials the factors behind different phenomena were investigated. To reveal value and potential use of polysaccharide gels the influence of various factors such as concentration, temperature and ionic strength were determined. The measurements showed a clear difference between studied materials under investigated external parameters.

The effect of cationic-anionic polyelectrolyte multilayer surface treatment on inkjet ink spreading and print quality

The focus of the work reported in this thesis was to study and to clarify the effect of polyelectrolyte multilayer surface treatment on inkjet ink spreading, absorption and print quality. Surface sizing with a size press, film press with a pilot scale coater, and spray coating, have been used to surface treat uncoated wood-free, experimental wood-free and pigmentcoated substrates. The role of the deposited cationic (polydiallydimethylammonium chloride, PDADMAC) and anionic (sodium carboxymethyl cellulose, NaCMC) polyelectrolyte layers with and without nanosilica, on liquid absorption and spreading was studied in terms of their interaction with water-based pigmented and dye-based inkjet inks. Contact angle measurements were made in attempt to explain the ink spreading and wetting behavior on the substrate. First, it was noticed that multilayer surface treatment decreased the contact angle of water, giving a hydrophilic character to the surface. The results showed that the number of cationic-anionic polyelectrolyte layers or the order of deposition of the polyelectrolytes had a significant effect on the print quality. This was seen for example as a higher print density on layers with a cationic polyelectrolyte in the outermost layer. The number of layers had an influence on the print quality; the print density increased with increasing number of layers, although the increase was strongly dependent on ink formulation and chemistry. The use of nanosilica clearly affected the rate of absorption of polar liquids, which also was seen as a higher density of the black dye-based print. Slightly unexpected, the use of nanosilica increased the tendency for lateral spreading of both the pigmented and dye-based inks. It was shown that the wetting behavior and wicking of the inks on the polyelectrolyte coatings was strongly affected by the hydrophobicity of the substrate, as well as by the composition or structure of the polyelectrolyte layers. Coating only with a cationic polyelectrolyte was not sufficient to improve dye fixation, but it was demonstrated that a cationic-anionic-complex structure led to good water fastness. A threelayered structure gave the same water fastness values as a five-layered structure. Interestingly, the water fastness values were strongly dependent not only on the formed cation-anion polyelectrolyte complexes but also on the tendency of the coating to dissolve during immersion in water. Results showed that by optimizing the chemistry of the layers, the ink-substrate interaction can be optimized.

Regenerated cellulose ultrafiltration membranes in the treatment of pulp and paper mill process waters

Ultrafiltration (UF) is widely applied in different separation processes in the pulp and paper industry. The growing need to protect the environment, a lack of pure water and an interest in producing high-value chemicals from compounds present in process waters will probably lead to an increase in the use of UF in the pulp and paper industry. The efficiency and cost-effectiveness of a UF process depends on the applied membrane. The membrane should have a high and stable filtration capacity, a particular selectivity and a long operational lifetime. To meet these requirements a membrane should have a low fouling tendency. In addition, it should withstand the prevailing operational and chemical conditions. This thesis evaluates the performance and applicability of the regenerated cellulose (RC) membranes 00030T and C2 in the treatment of pulp and paper mill process waters based on the requirements above. The results demonstrated that both the tested RC membranes fulfilled well the requirement of high filtration capacity. In addition, in the filtration of a paper mill clear filtrate (CF) the RC membranes were not as greatly affected by variations in the CF quality as a polysulphone membrane. Furthermore, due to their extreme hydrophilicity and weak charge the fouling tendency of the membranes can be expected to be low in pulp and paper mill filtration applications. It is, however, known that fouling cannot be totally avoided even when the membrane is chosen very carefully. This study indicated that carbohydrates influenced negatively on permeability and caused fouling in the filtration of groundwood mill circulation water. Thus, a pre-treatment effectively reducing the amount of carbohydrates might help to maintain a stable capacity. However, the results of the thesis also showed that the removal of some of the possible foulants might just increase the harmful effect of others. Multivariate examination was useful in the understanding of the complicated factors causing the unstable capacity. The thesis also revealed that the 00030T and C2 membranes can be used at high pressure (max. tested pressure 12 bar). The C2 membrane, having a sponge-like substructure, was more pressure resistant, and its performance was more stable at high pressure compared to the UCO30T membrane containing macrovoids in its substructure. Both tested membranes can, according to the results, also be used at temperatures as high as 70°C in acidic, neutral and alkaline conditions. However, the use at extreme conditions might cause faster ageing of the membranes compared to ageing in neutral conditions. The thesis proved that both the tested RC membranes are very suitable for pulp and paper mill applications and that the membranes can be utilised in processes operating in challenging conditions. Thus, they could be used in more demanding applications than supposed earlier.

The effect of microfibrillated cellulose addition on drying shrinkage and dimensional stability of wood-free paper

Microfibrillated cellulose (MFC) is known to enhance strength properties of paper. Improved strength usually means increased bonding which is strongly connected to dimensional instability of paper. Dimensional instability is due to changes in moisture content of paper; when paper is moistened it expands and when dried, it shrinks. Hygroexpansion is linked to end-use problems and excessive drying shrinkage consumes strength potential. Effective use of materials requires controlling of these phenomena. There isn’t yet data concerning dimensional stability of papers containing MFC which restricts wider use of MFC. Main objective of the work was to evaluate dimensional stability of wood-free paper containing different amounts of MFC. Sheets were dried with different methods to see how drying strains effected on drying shrinkage and hygroexpansion. Also tensile strength was measured to find out the effect of MFC. Results were compared to sheets containing kraft fines and in some test points cationic starch was used alongside with MFC. MFC increased the dimensional instability of freely dried sheets. As the amounts of MFC increased the effects on dimensional stability became more severe. However the fineness of MFC didn’t play any important role. Both hygroexpansion and drying shrinkage were decreased with cationic starch addition. Prevention of drying shrinkage over powered the effects of additives on hygroexpansion. Tensile strength improved up till 7 % addition amount which could be set as the upper limit of MFC addition when paper preparation and tensile strength are concerned.

Granulation tissue formation -The effect of hydroxyapatite coating of cellulose on cellular differentiation

Haavan jyväiskudoksen muodostuminen – Hydroksiapatiittipinnoi-tetun selluloosasienen vaikutus solujen erilaistumiseen paranemisprosessin aikana Etsittäessä uusia luun bioyhteensopivia täytemateriaaleja selluloosasieni päällystettiin luun koostumusta muistuttavalla runsaasti piitä sisältävällä hydroksiapatiittikerroksella. Vastoin odotuksia hydroksiapatiittipinnoitettu selluloosa ei parantanut luun kasvua, vaan päinvastoin ylläpiti tulehdusta ja sidekudossolujen hakeutumista vamma-alueelle. Ihon alle implantoituna sama sienimateriaali edisti merkittävästi haavan verekkään jyväiskudoksen kasvua. Tämän löydöksen perusteella hydroksiapatiittipinnoitetun selluloosasienen vaikutusta haavan soluihin paranemisprosessin aikana tutkittiin tarkemmin ja havaittiin, että tulehdussolujen lisäksi sieniin kertyi tavallista enemmän sekä hematopoieettisia että mesenkymaalisia kantasoluja. Hematopoieettiset kantasolut sijaitsevat luuytimessä lähellä luun sisäpintaa. Luun hydroksiapatiitista vapautuu kalsiumioneja luun jatkuvan fysiologisen uudismuodostuksen ja hajottamisen yhteydessä. Kantasolut etsiytyvät luuytimeen kalsiumia aistivien reseptorien välityksellä. Koska luun pintakerrosta muistuttavasta hydroksiapatiittipinnoitteesta vapautuu kalsiumia, tämän ajateltiin toimivan selityksenä sille, että hematopoieettiset kantasolut hakeutuvat runsaslukuisesti juuri hydroksiapatiittipinnoitettuihin selluloosasieniin. Tämän hypoteesin mukaisesti hydroksiapatiittipinnoitettujen selluloosapalkkien läheisyydestä löydettiin suuria määriä kalsiumreseptoreja sisältäviä soluja. Jatkotutkimuksissa todettiin lisäksi, että hematopoieettiset kantasolut pystyivät sienissä erilaistumaan hemoglobiinia tuottaviksi soluiksi. Havaittujen punasolulinjan merkkiaineiden perusteella näyttäisikin siltä, että haavan paranemiskudoksessa tapahtuu paranemisen aikana ekstramedullaarista erytropoieesia. Nämä soluja ohjaavat vaikutukset saattavat olla hyödyllisiä vaikeasti paranevien haavojen hoidossa.

Adsorption of hydrogen sulfide by modified cellulose nano/microcrystals

Hydrogen sulfide is toxic and hazardous pollutant. It has been under great interest for past few years because of all the time tighten environmental regulations and increased interest of mining. Hydrogen sulfide gas originates from mining and wastewater treatment systems have caused death in two cases. It also causes acid rains and corrosion for wastewater pipelines. The aim of this master thesis was to study if chemically modified cellulose nanocrystals could be used as adsorbents to purify hydrogen sulfide out from water and what are the adsorption capacities of these adsorbents. The effects of pH and backgrounds on adsorption capacities of different adsorbents are tested. In theoretical section hydrogen sulfide, its properties and different purification methods are presented. Also analytical detection methods for hydrogen sulfide are presented. Cellulose nano/microcrystals, properties, application and different modification methods are discussed and finally theory of adsorption and modeling of adsorption is shortly discussed. In experimental section different cellulose nanocrystals based adsorbents are prepared and tested at different hydrogen sulfide concentrations and in different conditions. Result of experimental section was that the highest adsorption capacity at one component adsorption had wet MFC/CaCO3. At different pH the adsorption capacities of adsorbents changed quite dramatically. Also change of hydrogen sulfide solution background did have effect on adsorption capacities. Although, when tested adsorbents’ adsorption capacities are compared to those find in literatures, it seems that more development of MFC based adsorbents is needed.

Synthesis and Characterization of Cellulose fiber-silica nanocomposites

Cellulose fiber-silica nanocomposites with novel mechanical, chemical and thermal properties have potential to be widely applied in different area. Monodispered silica nanoparticles play an important role in enhancing hybrids properties of hardness, strength, thermal stability etc. On the other hand, cellulose is one of the world’s most abundant and renewable polymers and possesses several unique properties required in many areas and biomedicine. The aim of this master thesis is to study if silica particles from reaction of sodium silicate and sulphuric acid can be adsorbed onto cellulose fiber surfaces via in situ growth. First, nanosilica particles were synthesized. Effect of pH and silica contents were tested. In theoretical part, introduction of silica, methods of preparation of nanosilica from sodium silicate, effect factors and additives were discussed. Then, cellulose fiber-silica nanocomposites were synthesis via route from sodium silicate and route silicic acid. In the experiment of route from sodium silicate, the effects of types of sodium silicate, pH and target ratio of silica to fiber were investigated. From another aspect, the effects of types of sodium silicate, fiber concentration in mixture solution and target ratio of silica to fiber were tested in the experiment of route from silicic acid. Samples were investigated via zeta potential measurement, particle size distribution, ash content measurement and Scanning Electron Microscopy (SEM). The Results of the experiment of preparing silica sol were that the particle size of silica sol was smaller prepared in pH 11.7 than that prepared in pH 9.3. Then in the experiment of synthesis of cellulose fiber-silica nanocomposites, it was concluded that the zeta potential of all the samples were around -16 mV and the highest ash content of all the samples was only 1.4%. The results of SEM images showed only a few of silica particles could be observed on the fiber surface, which corresponded to the value of ash content measurement.

Functional cellulose microspheres for pharmaceutical applications

Dissolving cellulose is the first main step in preparing novel cellulosicmaterials. Since cellulosic fibres cannot be easily dissolved in water-based solvents, fibres were pretreated with ethanol-acid solution prior to the dissolution. Solubility and changes on the surface of the fibres were studied with microscopy and capillary viscometry. After the treatment, the cellulose fibres were soluble in alkaline urea-water solvent. The nature of this viscous solution was studied rheologically. Cellulose microspheres were prepared by extruding the alkaline cellulose solution through the needle into an acidic medium. By altering the temperature and acidity of the mediumit was possible to adjust the specific surface area and pore sizes of themicrospheres. A typical skin-core structure was found in all samples. Microspheres were oxidised in order to introduce anionic carboxylic acid groups (AGs). Anionic microspheres are more hydrophilic; their water-uptake increased 25 times after oxidation and they could swell almost to their original state (88%) after drying and shrinking. Swelling was studied in simulated physiological environments, corresponding to stomach acid and intestines (pH 1.2-7.4). Oxidised microspheres were used as a drug carriers. They demonstrated a highmass uniformity, which would enable their use for personalised dosing among different patients, including children. The drug was solidified in microspheres in amorphous form. This enhanced solubility and could be used for more challenging drugs with poor solubility. The pores of themicrospheres also remained open after the drug was loaded and they were dried. Regardless of the swelling, the drug was released at a constant rate in all environments.

Stability and properties of cellulose-sodium hydroxide solution systems

Since cellulose is a linear macromolecule it can be used as a material for regenerated cellulose fiber products e.g. in textile fibers or film manufacturing. Cellulose is not thermoformable, thus the manufacturing of these regenerated fibers is mainly possible through dissolution processes preceding the regeneration process. However, the dissolution of cellulose in common solvents is hindered due to inter- and intra-molecular hydrogen bonds in the cellulose chains, and relatively high crystallinity. Interestingly at subzero temperatures relatively dilute sodium hydroxide solutions can be used to dissolve cellulose to a certain extent. The objective of this work was to investigate the possible factors that govern the solubility of cellulose in aqueous NaOH and the solution stability. Cellulose-NaOH solutions have the tendency to form a gel over time and at elevated temperature, which creates challenges for further processing. The main target of this work was to achieve high solubility of cellulose in aqueous NaOH without excessively compromising the solution stability. In the literature survey an overview of the cellulose dissolution is given and possible factors contributing to the solubility and solution properties of cellulose in aqueous NaOH are reviewed. Furthermore, the concept of solution rheology is discussed. In the experimental part the focus was on the characterization of the used materials and properties of the prepared solutions mainly concentrating on cellulose solubility and solution stability.