Brief communication: Report on the impact of the 27 February 2010 earthquake (Chile, Mw 8.8) on rockfalls in the Las Cuevas valley, Argentina

Numerous rockfalls were detected in the Las Cuevas valley, Argentina, after the 27 February 2010 earthquake in Chile. Live rockfalls were observed during aftershocks of 11 March 2010. Many rockfall source areas coincide with known thrust fault and some areas presented a rockfall activity even after the tremors. Some rockfalls crossed the National Road 7 but no damages to houses or vehicles were reported. This study illustrates how the 27 February 2010 earthquake impacted on unstable slopes in a valley far from the earthquakes epicentre. It is an interesting addition to previous studies on landslides caused by earthquakes because of the high magnitude of the event and of its aftershocks.

Assessing alpine plant vulnerability to climate change: A modeling perspective

The potential ecological impact of ongoing climate change has been much discussed. High mountain ecosystems were identified early on as potentially very sensitive areas. Scenarios of upward species movement and vegetation shift are commonly discussed in the literature. Mountains being characteristically conic in shape, impact scenarios usually assume that a smaller surface area will be available as species move up. However, as the frequency distribution of additional physiographic factors (e.g., slope angle) changes with increasing elevation (e.g., with few gentle slopes available at higher elevation), species migrating upslope may encounter increasingly unsuitable conditions. As a result, many species could suffer severe reduction of their habitat surface, which could in turn affect patterns of biodiversity. In this paper, results from static plant distribution modeling are used to derive climate change impact scenarios in a high mountain environment. Models are adjusted with presence/absence of species. Environmental predictors used are: annual mean air temperature, slope, indices of topographic position, geology, rock cover, modeled permafrost and several indices of solar radiation and snow cover duration. Potential Habitat Distribution maps were drawn for 62 higher plant species, from which three separate climate change impact scenarios were derived. These scenarios show a great range of response, depending on the species and the degree of warming. Alpine species would be at greatest risk of local extinction, whereas species with a large elevation range would run the lowest risk. Limitations of the models and scenarios are further discussed.

Properties of debris flow deposits and source materials compared: implications for debris flow characterization

In the Alps, debris flow deposits generally contain < 5% clay-size particles, and the role of the surface-charged < 2 mu m particles is often neglected, although these particles may have a significant impact on the rheological properties of the interstitial fluid. The objective of this study was to compare debris flow deposits and parent materials from two neighbouring catchments of the Swiss Alps, with special emphasis on the colloidal constituents. The catchments are small in area (4 km(2)), 2.5 km long, similar in morphology, but different in geology. The average slopes are 35-40%. The catchments were monitored for debris flow events and mapped for surface aspect and erosion activity. Debris flow deposits and parent materials were sampled, the clay and silt fractions extracted and the bulk density, < 2 mm fraction bulk density, particle size distribution, chemical composition, cation exchange capacity (CEC) and mineralogy analysed. The results show that the deposits are similar to the parent screes in terms of chemical composition, but differ in terms of: (i) particle size distribution; and (ii) mineralogy, reactivity and density of the < 2 mm fraction. In this fraction, compared with the parent materials the deposits show dense materials enriched in coarse monocrystalline particles, of which the smallest and more reactive particles were leached. The results suggest that deposit samples should not be considered as representative of source or flow materials, particularly with respect to their physical properties.

Preliminary assessment of rockslide and rockfall hazards using a DEM (Oppstadhornet, Norway)

The increasing availability and precision of digital elevation model (DEM) helps in the assessment of landslide prone areas where only few data are available. This approach is performed in 6 main steps which include: DEM creation; identification of geomorphologic features; determination of the main sets of discontinuities; mapping of the most likely dangerous structures; preliminary rock-fall assessment; estimation of the large instabilities volumes. The method is applied to two the cases studies in the Oppstadhornet mountain (730m alt): (1) a 10 millions m3 slow-moving rockslide and (2) a potential high-energy rock falling prone area. The orientations of the foliation and of the major discontinuities have been determined directly from the DEM. These results are in very good agreement with field measurements. Spatial arrangements of discontinuities and foliation with the topography revealed hazardous structures. Maps of potential occurrence of these hazardous structures show highly probable sliding areas at the foot of the main landslide and potential rock falls in the eastern part of the mountain.

Modelling the influence of change in fire regime on the local distribution of a Mediterranean pyrophytic plant species (Cistus salviifolius) at its northern range limit

Aims: To assess the potential distribution of an obligate seeder and active pyrophyte, Cistus salviifolius, a vulnerable species in the Swiss Red List; to derive scenarios by changing the fire return interval; and to discuss the results from a conservation perspective. A more general aim is to assess the impact of fire as a natural factor influencing the vegetation of the southern slopes of the Alps. Locations: Alps, southern Switzerland. Methods: Presence-absence data to fit the model were obtained from the most recent field mapping of C. salviifolius. The quantitative environmental predictors used in this study include topographic, climatic and disturbance (fire) predictors. Models were fitted by logistic regression and evaluated by jackknife and bootstrap approaches. Changes in fire regime were simulated by increasing the time-return interval of fire (simulating longer periods without fire). Two scenarios were considered: no fire in the past 15 years; or in the past 35 years. Results: Rock cover, slope, topographic position, potential evapotranspiration and time elapsed since the last fire were selected in the final model. The Nagelkerke R-2 of the model for C. salviifolius was 0.57 and the Jackknife area under the curve evaluation was 0.89. The bootstrap evaluation revealed model robustness. By increasing the return interval of fire by either up to 15 years, or 35 years, the modelled C. salviifolius population declined by 30-40%, respectively. Main conclusions: Although fire plays a significant role, topography and rock cover appear to be the most important predictors, suggesting that the distribution of C. salviifolius in the southern Swiss Alps is closely related to the availability of supposedly competition-free sites, such as emerging bedrock, ridge locations or steep slopes. Fire is more likely to play a secondary role in allowing C. salviifolius to extend its occurrence temporarily, by increasing germination rates and reducing the competition from surrounding vegetation. To maintain a viable dormant seed bank for C. salviifolius, conservation managers should consider carrying out vegetation clearing and managing wild fire propagation to reduce competition and ensure sufficient recruitment for this species.

Flow structures at an idealized bifurcation : a numerical experiment

River bifurcations are key nodes within braided river systems controlling the flow and sediment partitioning and therefore the dynamics of the river braiding process. Recent research has shown that certain geometrical configurations induce instabilities that lead to downstream mid-channel bar formation and the formation of bifurcations. However, we currently have a poor understanding of the flow division process within bifurcations and the flow dynamics in the downstream bifurcates, both of which are needed to understand bifurcation stability. This paper presents results of a numerical sensitivity experiment undertaken using computational fluid dynamics (CFD) with the purpose of understanding the flow dynamics of a series of idealized bifurcations. A geometric sensitivity analysis is undertaken for a range of channel slopes (0.005 to 0.03), bifurcation angles (22 degrees to 42 degrees) and a restricted set of inflow conditions based upon simulating flow through meander bends with different curvature on the flow field dynamics through the bifurcation. The results demonstrate that the overall slope of the bifurcation affects the velocity of flow through the bifurcation and when slope asymmetry is introduced, the flow structures in the bifurcation are modified. In terms of bifurcation evolution the most important observation appears to be that once slope asymmetry is greater than 0.2 the flow within the steep bifurcate shows potential instability and the potential for alternate channel bar formation. Bifurcation angle also defines the flow structures within the bifurcation with an increase in bifurcation angle increasing the flow velocity down both bifurcates. However, redistributive effects of secondary circulation caused by upstream curvature can very easily counter the effects of local bifurcation characteristics. Copyright (C) 2011 John Wiley & Sons, Ltd.

Biomechanical analysis of alpine skiers performing giant slalom turns

Over the past few years, technological breakthroughs have helpedcompetitive sports to attain new levels. Training techniques, athletes' management and methods to analyse specific technique and performancehave sharpened, leading to performance improvement. Alpine skiing is not different. The objective of the present work was to study the technique of highy skilled alpine skiers performing giant slalom, in order to determine the quantity of energy that can be produced by skiers to increase their speed. To reach this goal, several tools have been developed to allow field testing on ski slopes; a multi cameras system, a wireless synchronization system, an aerodynamic drag model and force plateforms have especially been designed and built. The analyses performed using the different tools highlighted the possibility for several athletes to increase their energy by approximately 1.5 % using muscular work. Nevertheless, the athletes were in average not able to use their muscular work in an efficient way. By offering functional tools such as drift analysis using combined data from GPS and inertial sensors, or trajectory analysis based on tracking morphological points, this research makes possible the analysis of alpine skiers technique and performance in real training conditions. The author wishes for this work to be used as a basis for continued knowledge and understanding of alpine skiing technique. - Le sport de compétition bénéficie depuis quelques années des progrès technologiques apportés par la science. Les techniques d'entraînement, le suivi des athlètes et les méthodes d'analyse deviennent plus pointus, induisant une nette amélioration des performances. Le ski alpin ne dérogeant pas à cette règle, l'objectif de ce travail était d'analyser la technique de skieurs de haut niveau en slalom géant afin de déterminer la quantité d'énergie fournie par les skieurs pour augmenter leur vitesse. Pour ce faire, il a été nécessaire de developer différents outils d'analyse adaptés aux contraintes inhérentes aux tests sur les pistes de skis; un système multi caméras, un système de synchronisation, un modèle aérodynamique et des plateformes de force ont notamment été développés. Les analyses effectuées grâce à ces différents outils ont montré qu'il était possible pour certains skieur d'augmenter leur énergie d'environ 1.5 % grâce au travail musculaire. Cependant, les athlètes n'ont en moyenne pas réussi à utiliser leur travail musculaire de manière efficace. Ce projet a également rendu possible des analyses adaptées aux conditions d'entraînement des skieurs en proposant des outils fonctionnels tels que l'analyse du drift grâce à des capteurs inertiels et GPS, ainsi que l'analyse simplifiée de trajectoires grâce au suivi de points morphologiques. L'auteur espère que ce travail servira de base pour approfondir les connaissances de la technique en ski alpin.

Groundwater fluctuations and footslope ferricrete soils in the humid tropical zone of southern Cameroon

This paper discusses the relationship between the differentiation of ferruginous accumulations and the variable water saturation of footslope soil patterns. An analysis of the slope morphology of a typical hill in the forest zone of southern Cameroon and a seasonal survey of the levels of groundwaters, springs and rivers were considered in relation to the petrology of different soil patterns. The study site is a tabular hillock whose slopes present a progressive development from steep to gentle slopes. The variable residence time of water within the soil, creating an alternation of reducing and oxidizing conditions, affects oil chemistry, structure and lateral extension of the soil patterns. The ferruginous soil patterns, being formed on the footslopes, gradually increase in extent with decreasing slope angle and the relative rise of the groundwater level. The steep footslopes, where groundwater has a shorter residence time, show a soft mottled clay pattern, restricted to the bottom part of the slope. The moderate footslopes exhibit a deep permanent and a temporary perched groundwater table. The latter, with its regular capillary fringe, contributes to more reducing conditions within isolated domains in the soil patterns, and thus to the alternation with oxidizing conditions, generating a continuous hard soil pattern (massive carapace). The more gently dipping footslopes exhibit groundwater levels near the surface and also a significant amplitude of groundwater fluctuation. Iron, previously accumulated in moderate footslope patterns, is reduced, remobilized, and leached. The soil patterns formed develop into a variegated carapace, more extended along the slope, containing less iron, but nevertheless more hardened, due to the important fluctuations of the groundwater table. These patterns are limited to the zone of groundwater fluctuation and deteriorate as the water fluctuation zone recedes. Copyright (c) 2005 John Wiley & Sons, Ltd.

Detection, analysis and monitoring of slope movements by high-resolution digital elevation models

Summary Detection, analysis and monitoring of slope movements by high-resolution digital elevation modelsSlope movements, such as rockfalls, rockslides, shallow landslides or debris flows, are frequent in many mountainous areas. These natural hazards endanger the inhabitants and infrastructures making it necessary to assess the hazard and risk caused by these phenomena. This PhD thesis explores various approaches using digital elevation models (DEMs) - and particularly high-resolution DEMs created by aerial or terrestrial laser scanning (TLS) - that contribute to the assessment of slope movement hazard at regional and local scales.The regional detection of areas prone to rockfalls and large rockslides uses different morphologic criteria or geometric instability factors derived from DEMs, i.e. the steepness of the slope, the presence of discontinuities, which enable a sliding mechanism, and the denudation potential. The combination of these factors leads to a map of susceptibility to rockfall initiation that is in good agreement with field studies as shown with the example of the Little Mill Campground area (Utah, USA). Another case study in the Illgraben catchment in the Swiss Alps highlighted the link between areas with a high denudation potential and actual rockfall areas.Techniques for a detailed analysis and characterization of slope movements based on high-resolution DEMs have been developed for specific, localized sites, i.e. ancient slide scars, present active instabilities or potential slope instabilities. The analysis of the site's characteristics mainly focuses on rock slopes and includes structural analyses (orientation of discontinuities); estimation of spacing, persistence and roughness of discontinuities; failure mechanisms based on the structural setting; and volume calculations. For the volume estimation a new 3D approach was tested to reconstruct the topography before a landslide or to construct the basal failure surface of an active or potential instability. The rockslides at Åknes, Tafjord and Rundefjellet in western Norway were principally used as study sites to develop and test the different techniques.The monitoring of slope instabilities investigated in this PhD thesis is essentially based on multitemporal (or sequential) high-resolution DEMs, in particular sequential point clouds acquired by TLS. The changes in the topography due to slope movements can be detected and quantified by sequential TLS datasets, notably by shortest distance comparisons revealing the 3D slope movements over the entire region of interest. A detailed analysis of rock slope movements is based on the affine transformation between an initial and a final state of the rock mass and its decomposition into translational and rotational movements. Monitoring using TLS was very successful on the fast-moving Eiger rockslide in the Swiss Alps, but also on the active rockslides of Åknes and Nordnesfjellet (northern Norway). One of the main achievements on the Eiger and Aknes rockslides is to combine the site's morphology and structural setting with the measured slope movements to produce coherent instability models. Both case studies also highlighted a strong control of the structures in the rock mass on the sliding directions. TLS was also used to monitor slope movements in soils, such as landslides in sensitive clays in Québec (Canada), shallow landslides on river banks (Sorge River, Switzerland) and a debris flow channel (Illgraben).The PhD thesis underlines the broad uses of high-resolution DEMs and especially of TLS in the detection, analysis and monitoring of slope movements. Future studies should explore in more depth the different techniques and approaches developed and used in this PhD, improve them and better integrate the findings in current hazard assessment practices and in slope stability models.Résumé Détection, analyse et surveillance de mouvements de versant à l'aide de modèles numériques de terrain de haute résolutionDes mouvements de versant, tels que des chutes de blocs, glissements de terrain ou laves torrentielles, sont fréquents dans des régions montagneuses et mettent en danger les habitants et les infrastructures ce qui rend nécessaire d'évaluer le danger et le risque causé par ces phénomènes naturels. Ce travail de thèse explore diverses approches qui utilisent des modèles numériques de terrain (MNT) et surtout des MNT de haute résolution créés par scanner laser terrestre (SLT) ou aérien - et qui contribuent à l'évaluation du danger de mouvements de versant à l'échelle régionale et locale.La détection régionale de zones propices aux chutes de blocs ou aux éboulements utilise plusieurs critères morphologiques dérivés d'un MNT, tels que la pente, la présence de discontinuités qui permettent un mécanisme de glissement ou le potentiel de dénudation. La combinaison de ces facteurs d'instabilité mène vers une carte de susceptibilité aux chutes de blocs qui est en accord avec des travaux de terrain comme démontré avec l'exemple du Little Mill Campground (Utah, États-Unis). Un autre cas d'étude - l'Illgraben dans les Alpes valaisannes - a mis en évidence le lien entre les zones à fort potentiel de dénudation et les sources effectives de chutes de blocs et d'éboulements.Des techniques pour l'analyse et la caractérisation détaillée de mouvements de versant basées sur des MNT de haute résolution ont été développées pour des sites spécifiques et localisés, comme par exemple des cicatrices d'anciens éboulements et des instabilités actives ou potentielles. Cette analyse se focalise principalement sur des pentes rocheuses et comprend l'analyse structurale (orientation des discontinuités); l'estimation de l'espacement, la persistance et la rugosité des discontinuités; l'établissement des mécanismes de rupture; et le calcul de volumes. Pour cela une nouvelle approche a été testée en rétablissant la topographie antérieure au glissement ou en construisant la surface de rupture d'instabilités actuelles ou potentielles. Les glissements rocheux d'Åknes, Tafjord et Rundefjellet en Norvège ont été surtout utilisés comme cas d'étude pour développer et tester les diverses approches. La surveillance d'instabilités de versant effectuée dans cette thèse de doctorat est essentiellement basée sur des MNT de haute résolution multi-temporels (ou séquentiels), en particulier des nuages de points séquentiels acquis par SLT. Les changements topographiques dus aux mouvements de versant peuvent être détectés et quantifiés sur l'ensemble d'un glissement, notamment par comparaisons des distances les plus courtes entre deux nuages de points. L'analyse détaillée des mouvements est basée sur la transformation affine entre la position initiale et finale d'un bloc et sa décomposition en mouvements translationnels et rotationnels. La surveillance par SLT a démontré son potentiel avec l'effondrement d'un pan de l'Eiger dans les Alpes suisses, mais aussi aux glissements rocheux d'Aknes et Nordnesfjellet en Norvège. Une des principales avancées à l'Eiger et à Aknes est la création de modèles d'instabilité cohérents en combinant la morphologie et l'agencement structural des sites avec les mesures de déplacements. Ces deux cas d'étude ont aussi démontré le fort contrôle des structures existantes dans le massif rocheux sur les directions de glissement. Le SLT a également été utilisé pour surveiller des glissements dans des terrains meubles comme dans les argiles sensibles au Québec (Canada), sur les berges de la rivière Sorge en Suisse et dans le chenal à laves torrentielles de l'Illgraben.Cette thèse de doctorat souligne le vaste champ d'applications des MNT de haute résolution et particulièrement du SLT dans la détection, l'analyse et la surveillance des mouvements de versant. Des études futures devraient explorer plus en profondeur les différentes techniques et approches développées, les améliorer et mieux les intégrer dans des pratiques actuelles d'analyse de danger et surtout dans la modélisation de stabilité des versants.

Debris flow modeling for susceptibility mapping at regional to national scale in Norway

Debris flows and related landslide processes occur in many regions all over Norway and pose a significant hazard to inhabited areas. Within the framework of the development of a national debris flows susceptibility map, we are working on a modeling approach suitable for Norway with a nationwide coverage. The discrimination of source areas is based on an index approach, which includes topographic parameters and hydrological settings. For the runout modeling, we use the Flow-R model (IGAR, University of Lausanne), which is based on combined probabilistic and energetic algorithms for the assessment of the spreading of the flow and maximum runout distances. First results for different test areas have shown that runout distances can be modeled reliably. For the selection of source areas, however, additional factors have to be considered, such as the lithological and quaternary geological setting, in order to accommodate the strong variation in debris flow activity in the different geological, geomorphological and climate regions of Norway.

Multiple Kernel Learning of Environmental Data. Case study: Analysis and Mapping of Wind Fields

The paper presents the Multiple Kernel Learning (MKL) approach as a modelling and data exploratory tool and applies it to the problem of wind speed mapping. Support Vector Regression (SVR) is used to predict spatial variations of the mean wind speed from terrain features (slopes, terrain curvature, directional derivatives) generated at different spatial scales. Multiple Kernel Learning is applied to learn kernels for individual features and thematic feature subsets, both in the context of feature selection and optimal parameters determination. An empirical study on real-life data confirms the usefulness of MKL as a tool that enhances the interpretability of data-driven models.

Stratigraphie, morphodynamique, paléoenvironnements des terrains sédimentaires meubles à forte déclivité du domaine périglaciaire alpin

Dans le contexte d'un climat de plus en plus chaud, une étude « géosystémique » de la répartition du pergélisol dans l'ensemble d'un versant périglaciaire alpin, de la paroi rocheuse jusqu'au glacier rocheux, s'avère primordiale. S'insérant dans cette problématique, ce travail de thèse vise comme objectif général l'étude des versants d'éboulis situés à l'intérieur de la ceinture du pergélisol discontinu selon deux volets de recherche différents : une étude de la stratigraphie et de la répartition du pergélisol dans les éboulis de haute altitude et des processus qui lui sont associés ; une reconstitution de l'histoire paléoenvironnementale du domaine périglaciaire alpin pendant le Tardiglaciaire et l'Holocène. La stratigraphie et la répartition spatiale du pergélisol a été étudiée dans cinq éboulis des Alpes Valaisannes (Suisse), dont trois ont fait l'objet de forages profonds, grâce à la prospection géophysique de détail effectuée à l'aide de méthodes thermiques, de résistivité, sismiques et nucléaires. Les mesures effectuées ont permis de mettre en évidence que, dans les cinq éboulis étudiés, la répartition du pergélisol est discontinue et aucun des versants n'est intégralement occupé par du pergélisol. En particulier, il a été possible de prouver de manière directe que, dans un éboulis, le pergélisol est présent dans les parties inférieures du versant et absent dans les parties supérieures. Trois facteurs de contrôle principaux de la répartition du pergélisol déterminée au sein des éboulis étudiés ont été individualisés, pouvant agir seuls ou de manière combinée : la ventilation ascendante, l'augmentation de la granulométrie en direction de l'aval et la redistribution de la neige par le vent et les avalanches. Parmi ceux-ci, la relation ventilation-granulométrie semble être le facteur de contrôle principal permettant d'expliquer la présence de pergélisol dans les parties inférieures d'un éboulis et son absence dans les parties supérieures. Enfin, l'analyse de la structure des éboulis périglaciaires de haute altitude a permis de montrer que la stratigraphie du pergélisol peut être un élément important pour l'interprétation de la signification paléoclimatique de ce type de formes. Pour le deuxième volet de la recherche, grâce aux datations relatives effectuées à l'aide de l'utilisation conjointe de la méthode paléogéographique et du marteau de Schmidt, il a été possible de définir la chrono-stratigraphie du retrait glaciaire et du développement des glaciers rocheux et des versants d'éboulis des quatre régions des Alpes suisses étudiées (régions du Mont Gelé - Mont Fort, des Fontanesses et de Chamosentse, dans les Alpes Valaisannes, et Massif de la Cima di Gana Bianca, dans les Alpes Tessinoises). La compilation de toutes les datations effectuées a permis de montrer que la plupart des glaciers rocheux actifs étudiés se seraient développés soit juste avant et/ou pendant l'Optimum Climatique Holocène de 9.5-6.3 ka cal BP, soit au plus tard juste après cet évènement climatique majeur du dernier interglaciaire. Parmi les glaciers rocheux fossiles datés, la plupart aurait commencé à se former dans la deuxième moitié du Tardiglaciaire et se serait inactivé dans la première partie de l'Optimum Climatique Holocène. Pour les éboulis étudiés, les datations effectuées ont permis d'observer que leur surface date de la période entre le Boréal et l'Atlantique récent, indiquant que les taux d'éboulisation après la fin de l'Optimum Climatique Holocène ont dû être faibles, et que l'intervalle entre l'âge maximal et l'âge minimal est dans la plupart des cas relativement court (4-6 millénaires), indiquant que les taux d'éboulisation durant la période de formation des éboulis ont dû être importants. Grâce au calcul des taux d'érosion des parois rocheuses sur la base du volume de matériaux rocheux pour quatre des éboulis étudiés, il a été possible mettre en évidence l'existence d'une « éboulisation parapériglaciaire » liée à la dégradation du pergélisol dans les parois rocheuses, fonctionnant principalement durant les périodes de réchauffement climatique rapide comme cela a été le cas au début du Bølling, du Préboréal à la fin de l'Atlantique récent et, peut-être, à partir des années 1980. - In the context of a warmer climate, a « geosystemical » study of the permafrost distribution in a whole alpine periglacial hillslope, from the rockwall to the rockglacier, is of great importance. With respect to this problem, the general objective of this PhD thesis is the global study of talus slopes located within the alpine periglacial belt following two different research axes: the analysis of the internal structure and of the permafrost distribution of high altitude talus slopes and of the related processes; the reconstruction of the palaeoenvironmental history of the alpine periglacial belt during the Lateglacial and the Holocene. The stratigraphy and the permafrost distribution were studied in five talus slopes of the Valais Alps (Switzerland) with the analysis of borehole data (on three of the five talus slopes) and other methods of permafrost prospecting: Electrical Resistivity Tomography (ERT), Refraction Seismic Tomography (RST) and nuclear well logging. The collected data shows that, in all of the studied talus slopes, permafrost distribution is discontinuous and that neither of the hillslopes is integrally characterised by permafrost. In particular, this data proves by direct investigations that, in talus slopes, permafrost is present in the lower parts of the hillslope, whereas it is absent in the upper parts. Permafrost distribution in alpine talus slopes is depending of the combination of almost three controlling factors, whose respective importance is variable: the chimney effect, the increase of grain size downslope and the redistribution of snow by avalanches. Depending on the size of the talus and on topographical and geomorphological heterogeneities, various cases are possible: one dominant controlling factor or the combination of various factors. Nevertheless, it would be an error to consider each controlling factor independently, without considering their relationships. Between these controlling factors, the relationship chimney effect/grain size seems to be the most important factor controlling the presence of permafrost in the lowest part of periglacial talus slopes, and its absence in the upper parts. Finally, the analysis of the talus structure shows that the permafrost stratigraphy may be an important element of interpretation of the palaeoclimatic significance of an alpine talus slope. The second research axe focused on the establishment of a chronology of the Lateglacial glacier retreat and the dating of rockglaciers and talus slopes development in four studied regions of the Swiss Alps (Mont Gelé - Mont Fort, Fontanesses and Chamosentse regions, in the Valais Alps, and the Cima di Gana Bianca Massif, in the Ticino Alps). The compilation of the dates acquired through the combination of the palaeogeographical method and of the Schmidt hammer indicates that most of the investigated active rockglaciers started to evolve during the early phases of the Holocene or, at the latest, after the early-to-mid Holocene Climatic Optimum (ending around 6.3 ka cal BP). For the dated relict rockglaciers, most of them started to evolve in the second half of the Lateglacial, and probably became inactive at the beginning of the Holocene Climatic Optimum. For the investigated talus slopes, the relative dating carried out allowed to show that their surface date from the period included between the Boreal and the end of the Atlantic, pointing out that the rockwall retreat after the end of the Holocene Climatic Optimum was weak, and that the interval between maximal and minimal ages is in most cases relatively short (4-6 millennia). Therefore, the rockwall retreat during the development period of the talus slopes must has been considerable. Thanks to the calculation of rockwall erosion rates based on the volume of talus accumulations for four of the investigated hillslopes, it was possible to find evidences of the existence of "paraperiglacial rockfall phases" related to the permafrost degradation in rockwalls. These phases coincide with rapid climate warming periods, as at the beginning of the Bølling, during the Preboreal or, maybe, since 1980.

Modelling hydrodynamics in the Rio Parana, Argentina : an evaluation and inter-comparison of reduced-complexity and physics based models applied to a large sand-bed river

Depth-averaged velocities and unit discharges within a 30 km reach of one of the world's largest rivers, the Rio Parana, Argentina, were simulated using three hydrodynamic models with different process representations: a reduced complexity (RC) model that neglects most of the physics governing fluid flow, a two-dimensional model based on the shallow water equations, and a three-dimensional model based on the Reynolds-averaged Navier-Stokes equations. Row characteristics simulated using all three models were compared with data obtained by acoustic Doppler current profiler surveys at four cross sections within the study reach. This analysis demonstrates that, surprisingly, the performance of the RC model is generally equal to, and in some instances better than, that of the physics based models in terms of the statistical agreement between simulated and measured flow properties. In addition, in contrast to previous applications of RC models, the present study demonstrates that the RC model can successfully predict measured flow velocities. The strong performance of the RC model reflects, in part, the simplicity of the depth-averaged mean flow patterns within the study reach and the dominant role of channel-scale topographic features in controlling the flow dynamics. Moreover, the very low water surface slopes that typify large sand-bed rivers enable flow depths to be estimated reliably in the RC model using a simple fixed-lid planar water surface approximation. This approach overcomes a major problem encountered in the application of RC models in environments characterised by shallow flows and steep bed gradients. The RC model is four orders of magnitude faster than the physics based models when performing steady-state hydrodynamic calculations. However, the iterative nature of the RC model calculations implies a reduction in computational efficiency relative to some other RC models. A further implication of this is that, if used to simulate channel morphodynamics, the present RC model may offer only a marginal advantage in terms of computational efficiency over approaches based on the shallow water equations. These observations illustrate the trade off between model realism and efficiency that is a key consideration in RC modelling. Moreover, this outcome highlights a need to rethink the use of RC morphodynamic models in fluvial geomorphology and to move away from existing grid-based approaches, such as the popular cellular automata (CA) models, that remain essentially reductionist in nature. In the case of the world's largest sand-bed rivers, this might be achieved by implementing the RC model outlined here as one element within a hierarchical modelling framework that would enable computationally efficient simulation of the morphodynamics of large rivers over millennial time scales. (C) 2012 Elsevier B.V. All rights reserved.

Contrasting diffusion of Quaternary gene pools across Europe: the case of the arctic-alpine Gentiana nivalis L. (Gentianaceae).

The fate of European arctic-alpine species during Pleistocene climatic oscillations still remains debated. Did these cold-adapted species invade much of the continental steppe or did they remain restricted to warmer slopes of inner mountain massifs? To examine this question, we investigated the phylogeography of Gentiana nivalis, a typical European arctic-alpine plant species. Genome fingerprinting analyses revealed that four genetic pools are actually unevenly distributed across the continent. One cluster covers almost all mountain massifs as well as northern areas, and thus coincides with a scenario of past distribution covering a large part of the European glacial steppe. In contrast, the three other lineages are strongly restricted spatially to western, central, and eastern Alps, respectively, thus arguing towards a scenario of in situ glacial survival. The coexistence of lineages with such contrasting demographic histories in Europe challenges our classical view of refugia and corroborates several hypotheses of biogeographers from the twentieth century.

Taxonomic status of Hylomys parvus and Hylomys suillus (Insectivora: Erinaceidae): biochemical and morphological analyses

The genus Hylomys was thought to be represented by a single widespread species. Biochemical and morphometric analyses of several Southeast Asian populations reveal that Sumatra is inhabited by two distinct species, the dwarf gymnure (H. parvus) and the lesser gymnure (H. suillus). The absence of interbreeding between these two groups along with their relatively ancient common origins are documented by several diagnostic loci and a large Nei's genetic distance (D = 0.353 +/- 0.035). The dwarf gymnure has been reported only from the slopes of the Mt. Kerinci volcano in Sumatra, where the species lives at higher elevations than its potential competitor, the lesser gymnure. Other populations of Hylomys from Java, Borneo, and Malaysia are more closely related to the Sumatran sample of H. suillus, but they exhibit strong interpopulational genetic differentiation (D = 0.165 +/- 0.040) that may be accounted for by their isolated montane habitat. In addition, a principal-components analysis based on 16 measurements of the skull clearly separates adult specimens of both species. There is little overlap in the measurements between H. suillus (which is larger) and H. parvus. On Sumatra where both species may be sympatric, the notched space between premaxillary tips, soft texture of the fur, and more delicate skull and dentition are diagnostic of H. parvus.