3D crosshole ERT for aquifer characterization and monitoring of infiltrating river water

The hydrogeological properties and responses of a productive aquifer in northeastern Switzerland are investigated. For this purpose, 3D crosshole electrical resistivity tomography (ERT) is used to define the main lithological structures within the aquifer (through static inversion) and to monitor the water infiltration from an adjacent river. During precipitation events and subsequent river flooding, the river water resistivity increases. As a consequence, the electrical characteristics of the infiltrating water can be used as a natural tracer to delineate preferential flow paths and flow velocities. The focus is primarily on the experiment installation, data collection strategy, and the structural characterization of the site and a brief overview of the ERT monitoring results. The monitoring system comprises 18 boreholes each equipped with 10 electrodes straddling the entire thickness of the gravel aquifer. A multi-channel resistivity system programmed to cycle through various four-point electrode configurations of the 180 electrodes in a rolling sequence allows for the measurement of approximately 15,500 apparent resistivity values every 7 h on a continuous basis. The 3D static ERT inversion of data acquired under stable hydrological conditions provides a base model for future time-lapse inversion studies and the means to investigate the resolving capability of our acquisition scheme. In particular, it enables definition of the main lithological structures within the aquifer. The final ERT static model delineates a relatively high-resistivity, low-porosity, intermediate-depth layer throughout the investigated aquifer volume that is consistent with results from well logging and seismic and radar tomography models. The next step will be to define and implement an appropriate time-lapse ERT inversion scheme using the river water as a natural tracer. The main challenge will be to separate the superposed time-varying effects of water table height, temperature, and salinity variations associated with the infiltrating water.

Early prediction of response to sunitinib after imatinib failure by 18F-fluorodeoxyglucose positron emission tomography in patients with gastrointestinal stromal tumor.

PURPOSE: Positron emission tomography with (18)F-fluorodeoxyglucose (FDG-PET) was used to evaluate treatment response in patients with gastrointestinal stromal tumors (GIST) after administration of sunitinib, a multitargeted tyrosine kinase inhibitor, after imatinib failure. PATIENTS AND METHODS: Tumor metabolism was assessed with FDG-PET before and after the first 4 weeks of sunitinib therapy in 23 patients who received one to 12 cycles of sunitinib therapy (4 weeks of 50 mg/d, 2 weeks off). Treatment response was expressed as the percent change in maximal standardized uptake values (SUV). The primary end point of time to tumor progression was compared with early PET results on the basis of traditional Response Evaluation Criteria in Solid Tumors (RECIST) criteria. RESULTS: Progression-free survival (PFS) was correlated with early FDG-PET metabolic response (P < .0001). Using -25% and +25% thresholds for SUV variations from baseline, early FDG-PET response was stratified in metabolic partial response, metabolically stable disease, or metabolically progressive disease; median PFS rates were 29, 16, and 4 weeks, respectively. Similarly, when a single FDG-PET positive/negative was considered after 4 weeks of sunitinib, the median PFS was 29 weeks for SUVs less than 8 g/mL versus 4 weeks for SUVs of 8 g/mL or greater (P < .0001). None of the patients with metabolically progressive disease subsequently responded according to RECIST criteria. Multivariate analysis showed shorter PFS in patients who had higher residual SUVs (P < .0001), primary resistance to imatinib (P = .024), or nongastric GIST (P = .002), regardless of the mutational status of the KIT and PDGFRA genes. CONCLUSION: Week 4 FDG-PET is useful for early assessment of treatment response and for the prediction of clinical outcome. Thus, it offers opportunities to individualize and optimize patient therapy.

Trabecular Bone Score (TBS)--A Novel Method to Evaluate Bone Microarchitectural Texture in Patients With Primary Hyperparathyroidism.

Context: In the milder form of primary hyperparathyroidism (PHPT), cancellous bone, represented by areal bone mineral density at the lumbar spine by dual-energy x-ray absorptiometry (DXA), is preserved. This finding is in contrast to high-resolution peripheral quantitative computed tomography (HRpQCT) results of abnormal trabecular microstructure and epidemiological evidence for increased overall fracture risk in PHPT. Because DXA does not directly measure trabecular bone and HRpQCT is not widely available, we used trabecular bone score (TBS), a novel gray-level textural analysis applied to spine DXA images, to estimate indirectly trabecular microarchitecture. Objective: The purpose of this study was to assess TBS from spine DXA images in relation to HRpQCT indices and bone stiffness in radius and tibia in PHPT. Design and Setting: This was a cross-sectional study conducted in a referral center. Patients: Participants were 22 postmenopausal women with PHPT. Main Outcome Measures: Outcomes measured were areal bone mineral density by DXA, TBS indices derived from DXA images, HRpQCT standard measures, and bone stiffness assessed by finite element analysis at distal radius and tibia. Results: TBS in PHPT was low at 1.24, representing abnormal trabecular microstructure (normal ≥1.35). TBS was correlated with whole bone stiffness and all HRpQCT indices, except for trabecular thickness and trabecular stiffness at the radius. At the tibia, correlations were observed between TBS and volumetric densities, cortical thickness, trabecular bone volume, and whole bone stiffness. TBS correlated with all indices of trabecular microarchitecture, except trabecular thickness, after adjustment for body weight. Conclusion: TBS, a measurement technology readily available by DXA, shows promise in the clinical assessment of trabecular microstructure in PHPT.

Growth mechanisms and timing of emplacement of a vertically layered mafic intrusion in the feeder zone of an ocean island volcano (Fuerteventura, Canary islands)

Résumé pour le grand public L'île de Fuerteventura (Canaries) offre l'occasion rare d'observer les racines d'un volcan océanique édifié il y a 25 à 30 millions d'années et complètement érodé. On y voit de nombreux petits plutons de forme et composition variées, témoignant d'autant d'épisodes de l'activité magmatique. L'un de ces plutons, appelé PX1, présente une structure inhabituelle formée d'une alternance de bandes verticales d'épaisseur métrique à hectométrique de roches sombres de composition pyroxénilique ou gabbroïque. Les pyroxénites résultent clairement de l'accumulation de cristaux de pyroxènes et non de la simple solidification d'un magma? Se pose dès lors la question de la nature du processus qui a conduit à l'accumulation verticale de niveaux concentrés en pyroxènes. En effet, les litages pyroxénitiques classiques sont subhorizontaux, car ils résultent de l'accumulation gravitaire des cristaux séparés du magma dont ils cristalli¬sent par sédimentation. Cette étude vise à identifier et comprendre les mécanismes qui ont engendré ce Iitage minéralogique vertical et l'im¬portant volume de ces faciès cumulatifs. Nous nous sommes également intéressés aux conditions de pression et de température régnant au moment de la mise en place du pluton, ainsi qu'à sa durée de vie et à sa vitesse de refroidis¬sement. Enfin une approche géochimique nous a permis de préciser la nature de la source mantellique des magmas liés à cette activité magmatique. PX1 est en réalité un complexe filonien formé à des conditions de pression et de température de 1-2 kbar et 1050- 1100°C; sa construction a nécessité au moins 150 km3 de magma. L'alternance d'horizons gabbroïques et pyroxéniti¬ques représente des injections successives de magma sous la forme de filons verticaux, mis en place dans un contexte régional en extension. L'étude des orientations des minéraux dans ces faciès révèle que les horizons gabbroïques enregistrent l'extension régionale, alors que les pyroxénites sont générées par une compaction au sein du pluton. Ceci suggère que le régime des contraintes, qui était extensif lors de l'initiation de la mise en place de PX1, est pério¬diquement devenu compressif au sein même du pluton. Cette compression serait liée à des cycles de mise en place où la vitesse de croissance du pluton dépassait celle de l'extension régionale. La différenciation observée au sein de chaque horizon, depuis des pyroxénites riches en olivine jusqu'à des pyroxé¬nites à plagioclase interstitiel et des gabbros, ainsi que la composition géochimique des minéraux qui les constituent suggèrent que chaque filon vertical s'est mis en place à partir d'un magma de composition identique, puis a évolué indépendamment des autres en fonction du régime thermique et du régime des contraintes local. Lorsque le magma en train de cristalliser s'est trouvé en compression, le liquide résiduel a été séparé des cristaux déjà formés et extrait du système, laissant derrière lui une accumulation de cristaux dont la nature et les proportions dépendaient du stade de cristallisation atteint par le magma au moment de l'extraction. Ainsi, les niveaux de pyroxénites à olivine (premier minéral à cristalliser) ont été formés lorsque le magma correspondant était encore peu cristallisé; à l'inverse, les py¬roxénites riches en plagioclase (minéral plus tardif dans la séquence de cristallisation) et certains gabbros à caractère cumulatif résultent d'une compression tardive dans le processus de cristallisation du filon concerné. Les liquides résiduels extraits des niveaux pyroxénitiques sont rarement observés dans PX1, certaines poches et filonets de com¬position anorthositique pourraient en être les témoins. L'essentiel de ces liquides a probablement gagné des niveaux supérieurs du pluton, voire la surface du volcan. L'origine du régime compressif périodique affectant les filons en voie de cristallisation est attribuée aux injections suivantes de magma au sein du pluton, qui se sont succédées à un rythme plus rapide que la vitesse de consolidation des filons. Des datations U/Pb de haute précision sur des cristaux de zircon et de baddeleyite ainsi que40Ar/39Ar sur des cris¬taux d'amphibole révèlent une initiation de la mise en place de PX1 il y a 22.1 ± 0,7 Ma; celle-ci a duré quelque 0,48 ± 0,22 à 0,52 ± 0,29 Ma. Ce laps de temps est compatible avec celui nécessaire à la cristallisation des filons individuels, qui va de moins d'une année lors de l'initiation du magmatisme à 5 ans lors du maximum d'activité de PX1. La présence de cristaux résorbés enregistrant une cristallisation complexe suggère l'existence d'une chambre mag¬matique convective sous-jacente à PX1 et périodiquement rechargée. Les compositions isotopiques des roches étu¬diées révèlent une source mantellique profonde de type point chaud avec une contribution du manteau lithosphéri- que métasomatisé présent sous les îles Canaries. Résumé L'intrusion mafique Miocène PX1 fait partie du soubassement superficiel (0.15-0.2 GPa, 1100 °Q d'un volcan d'île océanique. La particularité de ce pluton est l'existence d'alternances d'unités de gabbros et de pyroxénites qui met¬tent en évidence un litage magmatique vertical (NNE-SSW). Les horizons gabbroiques et pyroxénitiques sont constitués d'unités de différenciation métriques qui suggèrent tine mise en place par injections périodiques de filons verticaux de magma formant un complexe filonien. Chaque filon vertical a subi une différenciation parallèle à un front de solidification sub-vertical parallèle aux bords du filon. Les pyroxénites résultent du fractionnement et de l'accumulation d'olivine ± clinopyroxene ± plagioclase à partir d'un magma basaltique faiblement alcalin et sont interprétées comme étant des imités de différenciation tronquées dont le liquide interstitiel a été extrait par compaction. L'orientation préférentielle des clinopyroxènes dans ces pyroxe- nites (obtenues par analyse EBSD et micro-tomographique) révèle une composante de cisaillement simple dans la genèse de ces roches, ce qui confirme cette interprétation. La compaction des pyroxénites est probablement causée par a mise en place de filons de magma suivants. Le liquide interstitiel expulsé est probablement par ces derniers. Les clinopyroxènes des gabbros, montrent une composante de cisaillement pure suggérant qu'ils sont affectés par une déformation syn-magmatique parallèle aux zones de cisaillement NNE-SSW observées autour de PX1 et liées au contexte tectonique Miocène d'extension régionale. Ceci suggère que les gabbros sont liés à des taux de mise en place faibles à la fin de cycles d'activité magmatique et sont peu ou pas affectés par la compaction. L'initiation et la géométrie de PX1 sont donc contrôlées par le contexte tectonique régional d'extension alors que les taux et les volumes de magma dépendent de facteurs liés à la source. Des taux d'injection élevés résultent probable¬ment en une croissance du pluton supérieure à la place crée par cette extension. Dans ce cas de figure, la propagation des nouveaux dykes et l'inaptitude du magma à circuler à travers les anciens dykes cristallisés pourrait causer une augmentation de la pression non-lithostatique sur ces derniers, exprimée par un cisaillement simple et l'expulsion du liquide interstitiel qu'ils contiennent (documenté par les zones de collecte anorthositiques). Les compositions en éléments majeurs et traces des gabbros et pyroxenites de PX1 sont globalement homogènes et dépendent de la nature cumulative des échantillons. Cependant, de petites variations des concentrations en éléments traces ainsi que les teneurs en éléments traces des bordures de clinopyroxenes suggèrent que ces derniers ont subi un processus de rééquilibrage et de cristallisation in situ. L'homogénéité des compositions chimiques des échantillons, ainsi que la présence de grains de clinopyroxene résorbés suggère que le complexe filonien PX1 s'est mis en place au dessus d'une chambre magmatique périodiquement rechargée dans laquelle la convection est efficace. Chaque filon est donc issu d'un même magma, mais a subi une différenciation par cristallisation in situ (jusqu'à 70% de fraction¬nement) indépendamment des autres. Dans ces filons cristallisés, les minéraux cumulatifs subissent un rééquilibrage partiel avec les liquide interstitiel avant que ce dernier ne soit expulsé lors de la compaction (mettant ainsi un terme à la différenciation). Ce modèle de mise en place signifie qu'un minimum de 150Km3 de magma est nécessaire à la genèse de PX1, une partie de ce volume ayant été émis par le 'Central Volcanic Complex' de Fuerteventura. Les rapports isotopiques radiogéniques mesurés révèlent la contribution de trois pôles mantelliques dans la genèse du magma formant PX1. Le mélange de ces pôles HIMU, DMM et EM1 refléterai l'interaction du point chaud Cana¬rien avec un manteau lithosphérique hétérogène métasomatisé. Les petites variations de ces rapports et des teneurs en éléments traces au sein des faciès pourrait refléter des taux de fusion partielle variable de la source, résultant en un échantillonnage variable du manteau lithosphérique métasomatisé lors de son interaction avec le point chaud. Des datations U/Pb de haute précision (TIMS) sur des cristaux de zircon et de baddeleyite extraits de gabbros de PX1 révèlent que l'initiation de la cristallisation du magma a eu lieu il y a 22.10±0.07 Ma et que l'activité magmatique a duré un minimum de 0.48 à 0.52 Ma. Des âges 40Ar/39Ar obtenus sur amphibole sont de 21.9 ± 0.6 à 21.8 ± 0.3 Ma, identiques aux âges U/Pb. La combinaison de ces méthodes de datations, suggère que le temps maximum nécessaire à PX1 pour se refroidir en dessous de la température de fermeture de l'amphibole est de 0.8Ma. Ceci signifie que la durée de vie de PX1 est de 520 000 à 800 000 ans. La coexistence de cristaux de baddeleyite et de zircon dans un gabbro est attribuée à son interaction avec un fluide riche en C02 relâché par les carbonatites encaissantes lors du métamorphisme de contact généré par la mise en place de PX1 environ 160 000 ans après le début de sa mise en place. Les durées de vie obtenue sont en accord avec le modèle de mise en place suggérant une durée de cristallisation poux chaque filon allant de 1 an à 5 ans. Abstract The Miocene PX1 gabbro-pyroxenite intrusion (Fuerteventura, Canary Islands), is interpreted as the shallow-level feeder-zone (0.15-0.2 GPa and 1100-1120°C), to an ocean island volcano. The particularity of PX1 is that it displays a NNE-SSW trending vertical magmatic banding expressed by alternating gabbro and pyroxeriite sequences. The gabbro and pyroxenite sequences consist of metre-thick differentiation units, which suggest emplacement by pe¬riodic injection of magma pulses as vertical dykes that amalgamated, similarly to a sub-volcanic sheeted dyke com¬plex. Individual dykes underwent internal differentiation following a solidification front (favoured by a significant lateral/horizontal thermal gradient) parallel to the dyke edges. Pyroxenitic layers result from the fractionation and accumulation of clinopyroxene ± olivine ± plagioclase crystals from a mildly alkaline basaltic liquid and are interpre¬ted as truncated differentiation sequences, from which residual melts were extracted by compaction. Clinopyroxene mineral orientation in pyroxenites (evidenced by EBSD and micro X-ray tomography analysis) display a marked pure shear component, supporting this interpretation. Compaction and squeezing of the crystal mush is ascribed to the incoming and inflating magma pulses. The resulting expelled interstitial liquid was likely collected and erupted along with the magma flowing through the newly injected dykes. Gabbro sequences represent crystallised coalesced magma batches, emplaced at lower rates at the end of eruptive cycles, and underwent minor melt extraction as evi¬denced by clinopyroxene orientations that record a simple shear component suggesting syn-magmatic deformation parallel to observed NNF.-SSW trending shear-zones induced by the regional tensional Miocene stress-field. The initiation and geometry of PX1 is controlled by the regional extensional tectonic regime whereas rates and vo¬lumes of magma depend on source-related factors. High injection rates are likely to induce intrusion growth rates larger than could be accommodated by the regional extension. In this case, dyke tip geometry and the inability of magma to circulate through previously emplaced and crystallised dykes could result in an increase of non-lithostatic pressure on previously emplaced mushy dyke walls; generating strong pure-shear compaction and interstitial melt expulsion within the feeder-zone as recorded by the cumulitic pyroxenite bands and anorthositic collection zones. The whole-rock major and trace-element chemistry of PX1 gabbros and pyroxenites is globally homogeneous and controlled by the cumulate nature of the samples (i.e. on the modal proportions of olivine, pyroxene, plagioclase and oxides). However, small variations of whole-rock trace-element contents as well as trace-element contents of clinopyroxene rims suggest that in-situ re-equilibration and crystallisation has occurred. Additionally, the global homogeneity and presence of complex zoning of rare resorbed clinopyroxene crystals suggest that the PX1 feeder- zone overlies a periodically replenished and efficiently mixed magma chamber. Each individual dyke of magma thus originated from a compositionally constant mildly alkaline magma and differentiated independently from the others reaching up to 70% fractionation. Following dyke arrest these are affected by interaction with the trapped interstitial liquid prior to its compaction-linked expulsion (thus stopping the differentiation process). This emplacement model implies that minimum amount of approximately 150 km3 of magma is needed to generate PX1, part of it having been erupted through the overlying Central Volcanic Complex of Fuerteventura. The radiogenic isotope ratios of PX1 samples reveal the contribution on three end-members during magma genesis. This mixing of the H1MU, EMI and DMM end-members could reflect the interaction of the deep-seated Canarian mantle plume with a heterogeneous metasomatic and sepentininsed lithospheric mantle. Additionally, the observed trace-element and isotopic variations within the same fades groups could reflect varying degrees of partial melting of the source region, thus tapping more or less large areas of the metasomatised lithospheric mantle during interac¬tion with the plume. High precision ID-TIMS U/Pb zircon and baddeleyite ages from the PX1 gabbro samples, indicate initiation of magma crystallisation at 22.10 ± 0.07 Ma. The magmatic activity lasted a minimum of 0.48 to 0.52 Ma. 40Ar/39Ar amphibole ages are of 21.9 ± 0.6 to 21.8 ± 0.3, identical within errors to the U/Pb ages. The combination of the 40Ar/39Ar and U/Pb datasets imply that the maximum amount of time PX1 took to cool below amphibole Tc is 0.8 Ma, suggesting PX1 lifetime of 520 000 to 800 000 years. On top of this, the coexistence of baddeleyite and zircon in a single sample is ascribed to the interaction of PX1 with C02-rich carbonatite-derived fluids released from the host-rock carbonatites during contact metamorphism 160 000 years after PX1 initiation. These ages are in agreement with the emplacement model, implying a crystallisation time of less than 1 to 5 years for individual dykes.

Comparison of central macular thickness (CMT) measurement between time domain and spectral domain (SD) optical coherence tomography (OCT) and reproducibility of SD OCT in active neovascular AMD

Purpose: To evaluate the reproducibility of Cirrus-SD OCT measurements and to compare central macular thickness (CMT) measurements between TD-Stratus and SD-Cirrus OCT in patients with active exudative AMD. Methods: Consecutive case series of patients with active exudative AMD seen in the Medical Retina Department. Patients underwent 1 scan with Stratus (macular thickness map protocol) and 5 scans with Cirrus (Macular Cube protocol) at the same visit by the same experienced examiner. To be included, patients best-corrected visual acuity (BCVA) had to be >20/200 while all scans had to be of sufficient quality, well-centered and at least one Cirrus scan with CMT >300 microns. The repeatability of the SD Cirrus was estimated by using all 5 CMT measurements and the mean of the Cirrus measurements was compared with the CMT obtained by TD Stratus. Results: Cirrus OCT demonstrated high intraobserver repeatability at the central foveal region (ICC 96%). The mean of the CMT measurements was 321microns for Stratus and 387 microns for Cirrus. The average difference was 65m (SD=30). The coefficient of concordance between Stratus and Cirrus CMT measurements was rho=0,749 with a high precision and a moderate accuracy. The equation of the line of regression between Stratus and meanCirrus is given by the following: M_stratus = 0,848 x m_cirrus - 4,496 (1).Conclusions: The Cirrus macular cube protocol allows reproducible CMT measurements in patients with active exudative AMD. In cases of upgrading from TD to SD use and vice versa, there is the possibility to predict the measurements by using the equation (1). These real life data and conclusions can help in improving our clinical management of patients with neovascular AMD.

Radiation doses in computed tomography: pitfalls in comparing CT to chest X-ray

Rapid response to : Madan M Rehani and Manorma Berry Radiation doses in computed tomography BMJ 2000; 320: 593-594

Diagnosis of right ventricular dysfunction in acute pulmonary embolism using helical computed tomography.

Forty-six consecutive patients with pulmonary embolism (PE) who underwent pulmonary angiography, helical computed tomography (CT), and echocardiography in the investigators' emergency department were studied. It was determined that the CT right ventricular (RV)/left ventricular (LV) end-diastolic area ratio was correlated with PE obstruction and echocardiography. A CT RV/LV area ratio &gt;1 had a sensitivity of 88% and a specificity of 88% in diagnosing significant PE. The present study suggests that helical CT may be used as a triage tool in acute PE for selecting high-risk patients, using calculation of the RV/LV area ratio to detect RV dysfunction.

A case of acute retinal pigment epithelitis: spectral domain optical coherence tomography time course and physiopathologic hypothesis.

PURPOSE: To report the time course of retinal morphologic changes in a patient with acute retinal pigment epithelitis (ARPE) using spectral domain optical coherence tomography (SD-OCT). METHODS: A 30-year old man was referred for blurred vision of his right eye after five days that appeared suddenly 15 days after recovery from a flu-like syndrome. SD-OCT was performed immediately, followed by fluorescein and infracyanine angiography at eight days and then at three weeks. RESULTS: At presentation, a bubble of sub-macular deposit was observed on the right macula with central golden micronodules in a honeycomb pattern. SD-OCT showed an "anterior dislocation" of all the retinal layers up to the inner/outer segment (IS/OS) line and irregular deposits at the OS level together with thickening of the retinal pigment epithelial (RPE) layer. As visual acuity increased, eight days later, the OCT showed reduction of the sub-retinal deposits and an abnormal hyperflectivity of the sub-retinal and RPE layers was observed. The patient showed a positive serology for picornavirus. DISCUSSION: The acute SD-OCT sections of this patient with ARPE were compared with histological sections of a 35 day old Royal College of Surgeons rat. Similar findings could be observed, with preservation of the IS/OS line and accumulation of debris at the OS level, suggesting that ARPE symptoms could result from a transient phagocytic dysfunction of the RPE at the fovea, inducing reversible accumulation of undigested OS. Picornaviruses comprising enterovirus and coxsachievirus described as being associated with acute chorioretinitis. In this case, it was responsible for ARPE. CONCLUSION: We hypothesize that ARPE syndrome results from a transient dysfunction of RPE, which can occur as a post viral reaction.

Glucose metabolism, gray matter structure, and memory decline in subjective memory impairment.

OBJECTIVE: To identify biological evidence for Alzheimer disease (AD) in individuals with subjective memory impairment (SMI) and unimpaired cognitive performance and to investigate the longitudinal cognitive course in these subjects. METHOD: [¹⁸F]fluoro-2-deoxyglucose PET (FDG-PET) and structural MRI were acquired in 31 subjects with SMI and 56 controls. Cognitive follow-up testing was performed (average follow-up time: 35 months). Differences in baseline brain imaging data and in memory decline were assessed between both groups. Associations of memory decline with brain imaging data were tested. RESULTS: The SMI group showed hypometabolism in the right precuneus and hypermetabolism in the right medial temporal lobe. Gray matter volume was reduced in the right hippocampus in the SMI group. At follow-up, subjects with SMI showed a poorer performance than controls on measures of episodic memory. Longitudinal memory decline in the SMI group was associated with reduced glucose metabolism in the right precuneus at baseline. CONCLUSION: The cross-sectional difference in 2 independent neuroimaging modalities indicates early AD pathology in SMI. The poorer memory performance at follow-up and the association of reduced longitudinal memory performance with hypometabolism in the precuneus at baseline support the concept of SMI as the earliest manifestation of AD.

Analysis of a finite volume method for a cross-diffusion model in population dynamics

The main goal of this paper is to propose a convergent finite volume method for a reactionâeuro"diffusion system with cross-diffusion. First, we sketch an existence proof for a class of cross-diffusion systems. Then the standard two-point finite volume fluxes are used in combination with a nonlinear positivity-preserving approximation of the cross-diffusion coefficients. Existence and uniqueness of the approximate solution are addressed, and it is also shown that the scheme converges to the corresponding weak solution for the studied model. Furthermore, we provide a stability analysis to study pattern-formation phenomena, and we perform two-dimensional numerical examples which exhibit formation of nonuniform spatial patterns. From the simulations it is also found that experimental rates of convergence are slightly below second order. The convergence proof uses two ingredients of interest for various applications, namely the discrete Sobolev embedding inequalities with general boundary conditions and a space-time $L^1$ compactness argument that mimics the compactness lemma due to Kruzhkov. The proofs of these results are given in the Appendix.

Investigation of discrete imaging models and iterative image reconstruction in differential X-ray phase-contrast tomography.

Differential X-ray phase-contrast tomography (DPCT) refers to a class of promising methods for reconstructing the X-ray refractive index distribution of materials that present weak X-ray absorption contrast. The tomographic projection data in DPCT, from which an estimate of the refractive index distribution is reconstructed, correspond to one-dimensional (1D) derivatives of the two-dimensional (2D) Radon transform of the refractive index distribution. There is an important need for the development of iterative image reconstruction methods for DPCT that can yield useful images from few-view projection data, thereby mitigating the long data-acquisition times and large radiation doses associated with use of analytic reconstruction methods. In this work, we analyze the numerical and statistical properties of two classes of discrete imaging models that form the basis for iterative image reconstruction in DPCT. We also investigate the use of one of the models with a modern image reconstruction algorithm for performing few-view image reconstruction of a tissue specimen.

Assessment of glenoid inclination on routine clinical radiographs and computed tomography examinations of the shoulder.

BACKGROUND: Accurate assessment of glenoid inclination is of interest for a variety of conditions and procedures. The purpose of this study was to develop an accurate and reproducible measurement for glenoid inclination on standardized anterior-posterior (AP) radiographs and on computed tomography (CT) images. MATERIALS AND METHODS: Three consistently identifiable angles were defined: Angle α by line AB connecting the superior and inferior glenoid tubercle (glenoid fossa) and the line identifying the scapular spine; angle β by line AB and the floor of the supraspinatus fossa; angle γ by line AB and the lateral margin of the scapula. Experimental study: these 3 angles were measured in function of the scapular position to test their resistance to rotation. Conventional AP radiographs and CT scans were acquired in extension/flexion and internal/external rotation in a range up to ±40°. Clinical study: the inter-rater reliability of all angles was assessed on AP radiographs and CT scans of 60 patients (30 with proximal humeral fractures, 30 with osteoarthritis) by 2 independent observers. RESULTS: The experimental study showed that angle α and β have a resistance to rotation of up to ±20°. The deviation from neutral position was not more than ±10°. The results for the inter-rater reliability analyzed by Bland-Altman plots for the angle β fracture group were (mean ± standard deviation) -0.1 ± 4.2 for radiographs and -0.3 ± 3.3 for CT scans; and for the osteoarthritis group were -1.2 ± 3.8 for radiographs and -3.0 ± 3.6 for CT scans. CONCLUSION: Angle β is the most reproducible measurement for glenoid inclination on conventional AP radiographs, providing a resistance to positional variability of the scapula and a good inter-rater reliability.

Connexin 43 expression in human hypertrophied heart due to pressure and volume overload.

Left ventricular hypertrophy (LVH) is due to pressure overload or mechanical stretch and is thought to be associated with remodeling of gap-junctions. We investigated whether the expression of connexin 43 (Cx43) is altered in humans in response to different degrees of LVH. The expression of Cx43 was analyzed by quantitative polymerase chain reaction, Western blot analysis and immunohistochemistry on left ventricular biopsies from patients undergoing aortic or mitral valve replacement. Three groups were analyzed: patients with aortic stenosis with severe LVH (n=9) versus only mild LVH (n=7), and patients with LVH caused by mitral regurgitation (n=5). Cx43 mRNA expression and protein expression were similar in the three groups studied. Furthermore, immunohistochemistry revealed no change in Cx43 distribution. We can conclude that when compared with mild LVH or with LVH due to volume overload, severe LVH due to chronic pressure overload is not accompanied by detectable changes of Cx43 expression or spatial distribution.