Error probability in synchronous digital circuits due to power supply noise

This paper presents a probabilistic approach to model the problem of power supply voltage fluctuations. Error probability calculations are shown for some 90-nm technology digital circuits.The analysis here considered gives the timing violation error probability as a new design quality factor in front of conventional techniques that assume the full perfection of the circuit. The evaluation of the error bound can be useful for new design paradigms where retry and self-recoveringtechniques are being applied to the design of high performance processors. The method here described allows to evaluate the performance of these techniques by means of calculating the expected error probability in terms of power supply distribution quality.

Let's talk: how communication affects contract design

We study experimentally how the ability to communicate affects the frequency and effectiveness of flexible and inflexible contracts in a bilateral trade context where sellers can adjust trade quality after observing a post-contractual cost shock and a discretionary buyer transfer. In the absence of communication, we find that rigid contracts are more frequent and lead to higher earnings for both buyer and seller. By contrast, in the presence of communication, flexible contracts are much more frequent and considerably more productive, both for buyers and sellers. Also, both buyer and seller earn considerably more from flexible with communication than rigid without communication. Our results show quite strongly that communication, a normal feature in contracting, can remove the potential cost of flexibility (disagreements caused by conflicting perceptions). We offer an explanation based on social norms.

RTM mould design and construction for a DN 50 PN 16 flansch

The objective of this project consists of designing and constructing a RTM mould for a loose flange of glass fibre reinforced plastic (GRP). The design phase has the mission to realise a quality and simple design of the RTM mould, with the objective to obtain an easy and economic phase of construction and the more possible great characteristics of the loose flange. In fact this RTM mould will be a mould prototype, which will be developed in the future to obtain an RTM mould able to support a loose flange production. Therefore when more steps are developed in this project, then the future objective will be near

The COSMIN checklist for evaluating the methodological quality of studies on measurement properties: a clarification of its content

Background: The COSMIN checklist (COnsensus-based Standards for the selection of health status Measurement INstruments) was developed in an international Delphi study to evaluate the methodological quality of studies on measurement properties of health-related patient reported outcomes (HR-PROs). In this paper, we explain our choices for the design requirements and preferred statistical methods for which no evidence is available in the literature or on which the Delphi panel members had substantial discussion. Methods: The issues described in this paper are a reflection of the Delphi process in which 43 panel members participated. Results: The topics discussed are internal consistency (relevance for reflective and formative models, and distinction with unidimensionality), content validity (judging relevance and comprehensiveness), hypotheses testing as an aspect of construct validity (specificity of hypotheses), criterion validity (relevance for PROs), and responsiveness (concept and relation to validity, and (in) appropriate measures).Conclusions: We expect that this paper will contribute to a better understanding of the rationale behind the items, thereby enhancing the acceptance and use of the COSMIN checklist.

Design effect and interviewer effects: Evidence from the Spanish ESS3-2006 Data

In 2007 the first Quality Enhancement Meeting on sampling in the European SocialSurvey (ESS) took place. The discussion focused on design effects and inteviewereffects in face-to-face interviews. Following the recomendations of this meeting theSpanish ESS team studied the impact of interviewers as a new element in the designeffect in the response s variance using the information of the correspondent SampleDesign Data Files. Hierarchical multilevel and cross-classified multilevel analysis areconducted in order to estimate the amount of responses variation due to PSU and tointerviewers for different questions in the survey. Factor such as the age of theinterviewer, gender, workload, training and experience and respondent characteristicssuch as age, gender, renuance to participate and their possible interactions are alsoincluded in the analysis of some specific questions like trust in politicians and trustin legal system . Some recomendations related to future sampling designs and thecontents of the briefing sessions are derived from this initial research.

Traducción técnica del capítulo III del libro Advanced Data Warehouse design: from conventional to spatial and temporal applications

The proposal to work on this final project came after several discussions held with Dr. Elzbieta Malinowski Gadja, who in 2008 published the book entitled Advanced Data Warehouse Design: From Conventional to Spatial and Temporal Applications (Data-Centric Systems and Applications). The project was carried out under the technical supervision of Dr. Malinowski and the direct beneficiary was the University of Costa Rica (UCR) where Dr. Malinowski is a professor at the Department of Computer Science and Informatics. The purpose of this project was twofold: First, to translate chapter III of said book with the intention of generating educational material for the use of the UCR and, second, to venture in the field of technical translation related to data warehouse. For the first component, the goal was to generate a final product that would eventually serve as an educational tool for the post-graduate courses of the UCR. For the second component, this project allowed me to acquire new skills and put into practice techniques that have helped me not only to perfom better in my current job as an Assistant Translator of the Inter-American BAnk (IDB), but also to use them in similar projects. The process was lenggthy and required torough research and constant communication with the author. The investigation focused on the search of terms and definitions to prepare the glossary, which was the basis to start the translation project. The translation process itself was carried out by phases, so that comments and corrections by the author could be taken into account in subsequent stages. Later, based on the glossary and the translated text, illustrations had been created in the Visio software were translated. In addition to the technical revision by the author, professor Carme Mangiron was in charge of revising the non-technical text. The result was a high-quality document that is currently used as reference and study material by the Department of Computer Science and Informatics of Costa Rica.

Improvement of the quality factor of RF integrated inductors by layout optimization

A systematic method to improve the quality (Q) factor of RF integrated inductors is presented in this paper. The proposed method is based on the layout optimization to minimize the series resistance of the inductor coil, taking into account both ohmic losses, due to conduction currents, and magnetically induced losses, due to eddy currents. The technique is particularly useful when applied to inductors in which the fabrication process includes integration substrate removal. However, it is also applicable to inductors on low-loss substrates. The method optimizes the width of the metal strip for each turn of the inductor coil, leading to a variable strip-width layout. The optimization procedure has been successfully applied to the design of square spiral inductors in a silicon-based multichip-module technology, complemented with silicon micromachining postprocessing. The obtained experimental results corroborate the validity of the proposed method. A Q factor of about 17 have been obtained for a 35-nH inductor at 1.5 GHz, with Q values higher than 40 predicted for a 20-nH inductor working at 3.5 GHz. The latter is up to a 60% better than the best results for a single strip-width inductor working at the same frequency.

Quality of life following third molar removal under conscious sedation

Aim: The aim of this study was to assess quality of life (QoL) and degree of satisfaction among outpatients subjected to surgical extraction of all four third molars under conscious sedation. A second objective was to describe the evolution of self-reported pain measured in a visual analogue scale (VAS) in the 7 days after extraction. Study design: Fifty patients received a questionnaire assessing social isolation, working isolation, eating and speaking ability, diet modifications, sleep impairment, changes in physical appearance, discomfort at suture removal and overall satisfaction at days 4 and 7 after surgery. Pain was recorded by patients on a 100-mm pain visual analogue scale (VAS) every day after extraction until day 7. Results: Thirty-nine patients fulfilled correctly the questionnaire. Postoperative pain values suffered small fluctuations until day 5 (range: 23 to 33 mm in a 100-mm VAS), when dicreased significantly. A positive association was observed between difficult ranked surgeries and higher postoperative pain levels. The average number of days for which the patient stopped working was 4.9. Conclusion: The removal of all third molars in a single appointment causes an important deterioration of the patient"s QoL during the first postoperative week, especially due to local pain and eating discomfort.

Referral from primary care to a physical activity programme: establishing long-term adherence? A randomized controlled trial. Rationale and study design

Background: Declining physical activity is associated with a rising burden of global disease. There is little evidence about effective ways to increase adherence to physical activity. Therefore, interventions are needed that produce sustained increases in adherence to physical activity and are cost-effective. The purpose is to assess the effectiveness of a primary care physical activity intervention in increasing adherence to physical activity in the general population seen in primary care. Method and design: Randomized controlled trial with systematic random sampling. A total of 424 subjects of both sexes will participate; all will be over the age of 18 with a low level of physical activity (according to the International Physical Activity Questionnaire, IPAQ), self-employed and from 9 Primary Healthcare Centres (PHC). They will volunteer to participate in a physical activity programme during 3 months (24 sessions; 2 sessions a week, 60 minutes per session). Participants from each PHC will be randomly allocated to an intervention (IG) and control group (CG). The following parameters will be assessed pre and post intervention in both groups: (1) health-related quality of life (SF-12), (2) physical activity stage of change (Prochaska's stages of change), (3) level of physical activity (IPAQ-short version), (4) change in perception of health (vignettes from the Cooperative World Organization of National Colleges, Academies, and Academic Associations of Family Physicians, COOP/WONCA), (5) level of social support for the physical activity practice (Social Support for Physical Activity Scale, SSPAS), and (6) control based on analysis (HDL, LDL and glycated haemoglobin).Participants' frequency of visits to the PHC will be registered over the six months before and after the programme. There will be a follow up in a face to face interview three, six and twelve months after the programme, with the reduced version of IPAQ, SF-12, SSPAS, and Prochaska's stages. Discussion: The pilot study showed the effectiveness of an enhanced low-cost, evidence-based intervention in increased physical activity and improved social support. If successful in demonstrating long-term improvements, this randomised controlled trial will be the first sustainable physical activity intervention based in primary care in our country to demonstrate longterm adherence to physical activity. Trial Registration: A service of the U.S. National Institutes of Health. Developed by the National Library of Medicine. ClinicalTrials.gov ID: NCT00714831.

Design and optimization of selfnanoemulsifying drug delivery systems for enhanced dissolution of gemfibrozil

Self-nanoemulsifying drug delivery systems of gemfibrozil were developed under Quality by Design approach for improvement of dissolution and oral absorption. Preliminary screening was performed to select proper components combination. BoxBehnken experimental design was employed as statistical tool to optimize the formulation variables, X1 (Cremophor® EL), X2 (Capmul® MCM-C8), and X3 (lemon essential oil). Systems were assessed for visual characteristics (emulsification efficacy), turbidity, droplet size, polydispersity index and drug release. Different pH media were also assayed for optimization. Following optimization, the values of formulation components (X1, X2, and X3) were 32.43%, 29.73% and 21.62%, respectively (16.22% of gemfibrozil). Transmission electron microscopy demonstrated spherical droplet morphology. SNEEDS release study was compared to commercial tablets. Optimized SNEDDS formulation of gemfibrozil showed a significant increase in dissolution rate compared to conventional tablets. Both formulations followed Weibull mathematical model release with a significant difference in td parameter in favor of the SNEDDS. Equally amodelistic parameters were calculated being the dissolution efficiency significantly higher for SNEDDS, confirming that the developed SNEDDS formulation was superior to commercial formulation with respect to in vitro dissolution profile. This paper provides an overview of the SNEDDS of the gemfibrozil as a promising alternative to improve oral absorption.

Effectiveness of a primary care-based intervention to reduce sitting time in overweight and obese patients (SEDESTACTIV): a randomized controlled trial; rationale and study design

Background: There is growing evidence suggesting that prolonged sitting has negative effects on people's weight, chronic diseases and mortality. Interventions to reduce sedentary time can be an effective strategy to increase daily energy expenditure. The purpose of this study is to evaluate the effectiveness of a six-month primary care intervention to reduce daily of sitting time in overweight and mild obese sedentary patients. Method/Design: The study is a randomized controlled trial (RCT). Professionals from thirteen primary health care centers (PHC) will randomly invite to participate mild obese or overweight patients of both gender, aged between 25 and 65 years old, who spend 6 hours at least daily sitting. A total of 232 subjects will be randomly allocated to an intervention (IG) and control group (CG) (116 individuals each group). In addition, 50 subjects with fibromyalgia will be included. Primary outcome is: (1) sitting time using the activPAL device and the Marshall questionnaire. The following parameters will be also assessed: (2) sitting time in work place (Occupational Sitting and Physical Activity Questionnaire), (3) health-related quality of life (EQ-5D), (4) evolution of stage of change (Prochaska and DiClemente's Stages of Change Model), (5) physical inactivity (catalan version of Brief Physical Activity Assessment Tool), (6) number of steps walked (pedometer and activPAL), (7) control based on analysis (triglycerides, total cholesterol, HDL, LDL, glycemia and, glycated haemoglobin in diabetic patients) and (8) blood pressure and anthropometric variables. All parameters will be assessed pre and post intervention and there will be a follow up three, six and twelve months after the intervention. A descriptive analysis of all variables and a multivariate analysis to assess differences among groups will be undertaken. Multivariate analysis will be carried out to assess time changes of dependent variables. All the analysis will be done under the intention to treat principle. Discussion: If the SEDESTACTIV intervention shows its effectiveness in reducing sitting time, health professionals would have a low-cost intervention tool for sedentary overweight and obese patients management.

Calidad de vida y cáncer de próstata: un programa progresivo de fuerza-resistencia = Quality of life and prostate cancer: a progressive resistance strength program

This article presents the design and implementation of a progressive resistance strength program adapted to prostate cancer. The initial model corresponds to the guide of the American College Sports Medicine Position Stand (ACSM, 2009). This program includes the most habitual symptoms related to the illness and its treatments. The study design is quasi-experimental. The sample is 33 subjects in treatment phase. Study variables are tumour classification TNM, anthropometric measures, resistance strength, hypertension, fatigue, incontinence, pain and quality of life. After 24 weeks a significant improvement on resistance strength capacity is observed. This result is more consistent in lower extremities. Also improves hypertension, urinary incontinence, pain and quality of life. As conclusion, the improvement of the quality of life is mediated by the functional and physical capacity of the ill person

Satisfaction with pregnancy and delivery services: The quality of maternity care services as experienced by women

Objective: The objective of this study was to investigate the opinions of women regarding the satisfaction about the quality of maternity care received. We hope to establish whether health care technology increases satisfaction or whether it actually interferes with the construction of personal satisfaction in the process of care. Design and setting: Information was gathered using the focus group technique. The area of study comprised the post-natal groups run as part of the Sexual and Reproductive Health Programme of the Catalan Health Authority. (Spain) Participants: Five focus groups were held between May 2006 and July 2007. Findings: Quality of care is a complex concept in which a number of independent core features can be identified. We have grouped these core features into three basic categories. Safety: the hospital and its technological facilities, and the technical expertise of health professionals. The other two main pillars of quality of care are the human dimension of the relationship between the carers and the patient, and finally the structural aspects that determine the context in which the heath care is provided. Key conclusions and implications for practice: The mothers of our study feel satisfied with healthcare technology and view it as a source of security; technology become indispensable features in order to reduce the anxiety provoked by the perceived lack of confidence in their ability as mothers. In this study, women, both during pregnancy and especially when giving birth, believe their feelings and values should be understood by professionals, from whom they seek empathy and a personal commitment, and not just information.

Satisfaction with pregnancy and delivery services: The quality of maternity care services as experienced by women

Objective: The objective of this study was to investigate the opinions of women regarding the satisfaction about the quality of maternity care received. We hope to establish whether health care technology increases satisfaction or whether it actually interferes with the construction of personal satisfaction in the process of care. Design and setting: Information was gathered using the focus group technique. The area of study comprised the post-natal groups run as part of the Sexual and Reproductive Health Programme of the Catalan Health Authority. (Spain) Participants: Five focus groups were held between May 2006 and July 2007. Findings: Quality of care is a complex concept in which a number of independent core features can be identified. We have grouped these core features into three basic categories. Safety: the hospital and its technological facilities, and the technical expertise of health professionals. The other two main pillars of quality of care are the human dimension of the relationship between the carers and the patient, and finally the structural aspects that determine the context in which the heath care is provided. Key conclusions and implications for practice: The mothers of our study feel satisfied with healthcare technology and view it as a source of security; technology become indispensable features in order to reduce the anxiety provoked by the perceived lack of confidence in their ability as mothers. In this study, women, both during pregnancy and especially when giving birth, believe their feelings and values should be understood by professionals, from whom they seek empathy and a personal commitment, and not just information.

Traducción técnica del capítulo III del libro Advanced Data Warehouse design: from conventional to spatial and temporal applications

The proposal to work on this final project came after several discussions held with Dr. Elzbieta Malinowski Gadja, who in 2008 published the book entitled Advanced Data Warehouse Design: From Conventional to Spatial and Temporal Applications (Data-Centric Systems and Applications). The project was carried out under the technical supervision of Dr. Malinowski and the direct beneficiary was the University of Costa Rica (UCR) where Dr. Malinowski is a professor at the Department of Computer Science and Informatics. The purpose of this project was twofold: First, to translate chapter III of said book with the intention of generating educational material for the use of the UCR and, second, to venture in the field of technical translation related to data warehouse. For the first component, the goal was to generate a final product that would eventually serve as an educational tool for the post-graduate courses of the UCR. For the second component, this project allowed me to acquire new skills and put into practice techniques that have helped me not only to perfom better in my current job as an Assistant Translator of the Inter-American BAnk (IDB), but also to use them in similar projects. The process was lenggthy and required torough research and constant communication with the author. The investigation focused on the search of terms and definitions to prepare the glossary, which was the basis to start the translation project. The translation process itself was carried out by phases, so that comments and corrections by the author could be taken into account in subsequent stages. Later, based on the glossary and the translated text, illustrations had been created in the Visio software were translated. In addition to the technical revision by the author, professor Carme Mangiron was in charge of revising the non-technical text. The result was a high-quality document that is currently used as reference and study material by the Department of Computer Science and Informatics of Costa Rica.