Spectroscopic ellipsometry study of the In1-x Gax Asy P1-y / InP Heterojunctions grown by metalorganic chemical-vapor deposition

The dielectric functions of InP, In0.53Ga0.47As, and In0.75Ga0.25As0.5P0.5 epitaxial layers have been measured using a polarization modulation spectroscopic ellipsometer in the 1.5 to 5.3 eV region. The oxide removal procedure has been carefully checked by comparing spectroscopic ellipsometry and x ray photoelectron spectroscopy measurements. These reference data have been used to investigate the structural nature of metalorganic chemical vapor deposition grown In0.53Ga0.47As/InP and In0.75Ga0.25As0.5P0.5/InP heterojunctions, currently used for photodiodes and laser diodes. The sharpness of the interfaces has been systematically compared for the two types of heterojunctions: In1 xGaxAsy/InP and InP/In1 xGaxAsyP1 y. The sharpest interface is obtained for InP growth on In0.75Ga0.25As0.5P0.5 where the interface region is estimated to be (10±10) Å thick. The importance of performing in situ SE measurements is emphasized.

Study on the removal of biodegradable NOM from seawater using biofiltration

Despite the low biodegradability of seawater NOM, problems associated with biofouling are common in facilities that handle seawater. In this work, a fixed-film aerobic biofilter is proposed as an effective unit for preventing biofouling in such facilities. A packed-bed biofilter with an EBCT = 6 - 11 min was employed. The results demonstrated that the DOC is reduced by 6% and the BOD7 is reduced up to 15%. The LC-OCD analysis revealed that biofiltration abates the LMW neutrals and biopolymer fractions by 33 and 17%, respectively. However, the fractionation with UF membrane showed that the biofiltration process is able to degrade the more biodegradable compounds that have molecular weights that are greater than 1 kDa and compounds with molecular weights of less than 1 kDa. After biofiltration, the biological activity measured in terms of ATP removal was reduced by 60%. Finally, a test to evaluate the biofilm formation capacity of a water sample revealed reductions of ~94% when comparing biofiltered and non-biofiltered seawater. Therefore, a fixed-film aerobic biofiltration process could be a useful treatment for the removal of biodegradable organic matter from seawater and for improving the water quality in terms of less biofilm formation capacity.

Desarrollo y aplicación de estrategias de control avanzado en procesos biológicos de tratamiento de efluentes contaminados

En este proyecto se ha desarrollado estrategias de control avanzadas para plantas de depuración de aguas residuales urbanas que eliminan conjuntamente materia orgánica, nitrógeno y fósforo. Las estrategias se han basado en el estudio multivariable del comportamiento del sistema, que ha producido subsidios para la utilización de lazos de control feedforward, de control predictivo y de un control de costes que automáticamente enviaba las consignas más adecuadas para los controladores de proceso. Para el desarrollo de las estrategias, se ha creado un sistema virtual de simulación (simulador) de plantas de depuradoras, basado en datos de literatura. Para el caso de una planta real, se ha desarrollado un simulador de la planta de Manresa (Catalunya). Sin embargo, el sistema de Manresa se ha utilizado exclusivamente para auxiliar los ingenieros de la planta en la tomada de decisiones de cambio de configuración para que la eliminación de fósforo se dé por la ruta biológica y no por la ruta química. La implementación de los simuladores ha permitido hacer muchas pruebas que en una planta real demandarían mucho tiempo y consumirían muchos recursos energéticos y financieros. Las estrategias de control más elaboradas han podido ahorrar hasta 150.000,00 Euros por año en relación a la operación de la planta sin el control automático. Cuanto a los estudios del modelo de la planta real, se concluyó que la eliminación biológica de fósforo puede sustituir el actual proceso químico de eliminación de fósforo, bajando los costes operacionales (costes del agente precipitante).

Planta pilot d'una potabilitzadora

Treball de recerca realitzat per alumnes d'ensenyament secundari i guardonat amb un Premi CIRIT per fomentar l'esperit científic del Jovent l'any 2009. El treball ha consistit en dissenyar i construir una planta pilot d'una potabilitzadora que simulés el funcionament de les plantes potabilitzadores, basada en els mateixos principis . La Planta pilot de la potabilitzadora consta de les següents operacions: desbast, floculació, decantació, filtració de sorra, aireació, filtració de carbó actiu i desinfecció. La mostra utilitzada per la potabilització s’ha obtingut de l’embassament del Pasteral, lloc on la planta potabilitzadora de Girona capta l’aigua. Una vegada potabilitzada s’han realitzat una sèrie d’anàlisis tant a l’entrada com a la sortida, per determinar la variació obtinguda en diferents paràmetres del procés. Els tipus d’anàlisis realitzats són: fisicoquímics, microbiològics i organolèptics. Finalment, s’ha realitzat una comparació amb la potabilitzadora de Girona i s’ha verificat mitjançant els paràmetres de la normativa de l’aigua l'estat de la mostra.

Avenços en l'estudi de la litiasi renal: mètodes de chemical imaging i intel·ligencia artificial (ANN) per la caracterització de càlculs renals

La litiasi urinària és un trastorn que implica la formació de precipitats en qualsevol part del tracte urinari. Aquest és un desordre comú que afecta aproximadament a una desena part de la població de la Unió Europea al llarg de la seva vida. A més, durant els cinc anys posteriors a un episodi litiàsic el percentatge de recurrència dels pacients és del 45 al 75%. Aquest trastorn urinari està influït per una gran quantitat de variables, d’origen fisiològic, psicològic i ambiental. Els episodis litiàsics, es poden solucionar espontàniament, amb l’expulsió del càlcul renal, o bé a través de diverses intervencions mèdiques. Els tractaments mèdics derivats de la litiasi urinària; és a dir, la fragmentació del càlcul, intervencions quirúrgiques i tractaments posteriors generen unes grans despeses als sistemes mèdics. Pels motius exposats, la identificació del desordre que ha originat l’episodi litiàsic és de radical importància, per tal de minimitzar el risc de reincidència. Els mètodes més usuals per determinar les causes que desencadenen la formació del càlcul renal són les anàlisis d’orina i l’estudi del càlcul generat. La correcta descripció de la composició i, especialment, l’estructura del càlcul renal pot aportar informació clau sobre les possibles causes de la seva formació, tant de l’inici de nucleació del càlcul com de les successives etapes de creixement cristal·lí. Tenint en compte aquest darrer aspecte, el present estudi s’ha dirigit a la caracterització de càlculs urinaris mitjançant l’aplicació de metodologies d’imatge química (Hyperspectral Imaging), el que va contribuir a determinar les principals característiques espectrals de cada compost majoritari als càlculs renals. D’altra banda, la utilització de mostres de composició coneguda ha possibilitat la creació d’un model amb Xarxes Neuronals Artificials, que permet la classificació de noves mostres de composició desconeguda, de manera més ràpida que el procediment actual. Aquest treball constitueix una nova contribució a la comprensió de l’estructura de les pedres de ronyó, així com les condicions de la seva formació. Els resultats obtinguts destaquen les possibilitats que presenten les tècniques emprades al camp de la litiasi renal, que permeten complementar els coneixements existents enfocats a millorar la qualitat de vida dels pacients.

The chemical variability at the surface of Mars: implications for exogenic processes

The chemical composition of sediments and rocks, as well as their distribution at theMartian surface, represent a long term archive of processes, which have formed theplanetary surface. A survey of chemical compositions by means of Compositional DataAnalysis represents a valuable tool to extract direct evidence for weathering processesand allows to quantify weathering and sedimentation rates. clr-biplot techniques areapplied for visualization of chemical relationships across the surface (“chemical maps”).The variability among individual suites of data is further analyzed by means of clr-PCA,in order to extract chemical alteration vectors between fresh rocks and their crusts andfor an assessment of different source reservoirs accessible to soil formation. Bothtechniques are applied to elucidate the influence of remote weathering by combinedanalysis of several soil forming branches. Vector analysis in the Simplex provides theopportunity to study atmosphere surface interactions, including the role andcomposition of volcanic gases

Study of chemical modification of alkaline lignin by the glyoxalation reaction

In this study, glyoxalated alkaline lignins with a non-volatile and non-toxic aldehyde, which can be obtained from several natural resources, namely glyoxal, were prepared and characterized for its use in wood adhesives. The preparation method consisted of the reaction of lignin with glyoxal under an alkaline medium. The influence of reaction conditions such as the molar ratio of sodium hydroxide-to-lignin and reaction time were studied relative to the properties of the prepared adducts. The analytical techniques used were FTIR and 1H-NMR spectroscopies, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Results from both the FTIR and 1H-NMR spectroscopies showed that the amount of introduced aliphatic hydroxyl groups onto the lignin molecule increased with increasing reaction time and reached a maximum value at 10 h, and after they began to decrease. The molecular weights remained unchanged until 10 h of reaction time, and then started to increase, possibly due to the repolymerization reactions. DSC analysis showed that the glass transition temperature (Tg) decreased with the introduction of glyoxal onto the lignin molecule due to the increase in free volume of the lignin molecules. TGA analysis showed that the thermal stability of glyoxalated lignin is not influenced and remained suitable for wood adhesives. Compared to the original lignin, the improved lignin is reactive and a suitable raw material for adhesive formula

Nuclear magnetic resonance chemical shifts with the statistical average of orbital-dependent model potentials in Kohn-Sham density functional theory

The performance of the SAOP potential for the calculation of NMR chemical shifts was evaluated. SAOP results show considerable improvement with respect to previous potentials, like VWN or BP86, at least for the carbon, nitrogen, oxygen, and fluorine chemical shifts. Furthermore, a few NMR calculations carried out on third period atoms (S, P, and Cl) improved when using the SAOP potential

A chemical Hamiltonian approach study of the basis set superposition error changes on electron densities and one- and two-center energy components

A comparision of the local effects of the basis set superposition error (BSSE) on the electron densities and energy components of three representative H-bonded complexes was carried out. The electron densities were obtained with Hartee-Fock and density functional theory versions of the chemical Hamiltonian approach (CHA) methodology. It was shown that the effects of the BSSE were common for all complexes studied. The electron density difference maps and the chemical energy component analysis (CECA) analysis confirmed that the local effects of the BSSE were different when diffuse functions were present in the calculations

Study of the variability in chemical composition of bark layers of Quercus Suber L. from different production areas

Cork is the bark of the cork oak tree (Quercus suber L), a renewable and biodegradable raw bioresource concentrated mainly in the Mediterranean region. Development of its potential uses as a biosorbent will require the investigation of its chemical composition; such information can be of help to understand its interactions with organic pollutants. The present study investigates the summative chemical composition of three bark layers (back, cork, and belly) of five Spanish cork samples and one cork sample from Portugal. Suberin was the main component in all the samples (21.1 to 53.1%), followed by lignin (14.8 to 31%), holocellulose (2.3 to 33.6%), extractives (7.3 to 20.4%), and ash (0.4 to 3.3%). The Kruskal-Wallis test was used to determine whether the variations in chemical composition with respect to the production area and bark layers were significant. The results indicate that, with respect to the bark layer, significant differences were found only for suberin and holocellulose contents: they were higher in the belly and cork than in the back. Based on the results presented, cork is a material with a lot of potential because of its heterogeneity in chemical composition

Effects of convection on the removal of the multiplicity of stable states in one-dimensional vertical models

Here I develop a model of a radiative-convective atmosphere with both radiative and convective schemes highly simplified. The atmospheric absorption of radiation at selective wavelengths makes use of constant mass absorption coefficients in finite width spectral bands. The convective regime is introduced by using a prescribed lapse rate in the troposphere. The main novelty of the radiative-convective model developed here is that it is solved without using any angular approximation for the radiation field. The solution obtained in the purely radiation mode (i. e. with convection ignored) leads to multiple equilibria of stable states, being very similar to some results recently found in simple models of planetary atmospheres. However, the introduction of convective processes removes the multiple equilibria of stable states. This shows the importance of taking convective processes into account even for qualitative analyses of planetary atmosphere

Effluent particle removal by microirrigation system filters

The aim of this work was to determine whether the filters used in microirrigation systems can remove potentially emitter-clogging particles. The particle size and volume distributions of different effluents and their filtrates were established, and the efficiency of the removal of these particles and total suspended solids by screen, disc and sand filters determined. In most of the effluents and filtrates, the number of particles with a diameter > 20 μm was minimal. By analysing the particle volume distribution it was found that particles larger than the disc and screen filter pores appeared in the filtrates. However, the sand filter was able to retain particles larger than the pore size. The filtration efficiency depended more on the type of effluent than on the filter. It was also found that the particle size distribution followed a potential law. Analysis of the β exponents showed that the filters did not significantly modify the particle size distribution of the effluents

Botulinum neurotoxin type A blocks the morphological changes induced by chemical stimulation on the presynaptic membrane of Torpedo synaptosomes.

The action of botulinum neurotoxin on acetylcholine release, and on the structural changes at the presynaptic membrane associated with the transmitter release,was studied by using a subcellular fraction of cholinergic nerve terminals (synaptosomes) isolated from the Torpedo electric organ. Acetylcholine and ATP release were continuously monitored by chemiluminescent methods.To catch the membrane morphological changes, the quick-freezing method was applied. Our results show that botulinum neurotoxin inhibits the release of acetylcholine from these isolated nerve terminals in a dose-dependent manner, whereas ATP release is not affected. The maximal inhibition (70%) is achieved at neurotoxin concentrations as low as 125 pM with an incubation time of 6 min. This effect is not linked to an alteration of the integrity of the synaptosomes since, after poisoning by botulinum neurotoxin type A, they show a nonmodified occluded lactate dehydrogenase activity. Moreover, membrane potential is not altered by the toxin with respect to the control, either in resting condition or after potassium depolarization. In addition to acetylcholine release inhibition, botulinum neurotoxin blocks the rearrangement of the presynaptic intramembrane particles induced by potassium stimulation. The action of botulinum neurotoxin suggests that the intramembrane particle rearrangement is related to the acetylcholine secretion induced by potassium stimulation in synaptosomes isolated from the electric organ of Torpedo marmorata.

Gas collisions and pressure quenching of the photoluminescence of silicon nanopowder grown by plasma-enhanced chemical vapor deposition

The quenching of the photoluminescence of Si nanopowder grown by plasma-enhanced chemical vapor deposition due to pressure was measured for various gases ( H2, O2, N2, He, Ne, Ar, and Kr) and at different temperatures. The characteristic pressure, P0, of the general dependence I(P) = I0¿exp(¿P/P0) is gas and temperature dependent. However, when the number of gas collisions is taken as the variable instead of pressure, then the quenching is the same within a gas family (mono- or diatomic) and it is temperature independent. So it is concluded that the effect depends on the number of gas collisions irrespective of the nature of the gas or its temperature.