Use of antimicrobial biodegradable packaging to control Listeria monocytogenes during storage of cooked ham

The antimicrobial effect against L. monocytogenes of biodegradable films (alginate, zein and polyvinyl alcohol) containing enterocins was investigated. Survival of the pathogen was studied by means of challenge tests performed at 6 °C during 8 and 29 days, for air-packed and vacuum-packed sliced cooked ham, respectively. Air packaging was tested with two concentrations of enterocins (200 and 2000 AU/cm2). Control air-packed cooked ham showed an increase of L. monocytogenes from 104 to 107 CFU/g after 8 days. By contrast, packaging with antimicrobial films effectively slowed down the pathogen's growth, leading to final counts lower than in control lots. Air-packaging with alginate films containing 2000 AU/cm2 of enterocins effectively controlled L. monocytogenes for 8 days. An increase of only 1 log unit was observed in zein and polyvinyl alcohol lots at the same enterocin concentration. Vacuum packaging with films containing enterocins (2000 AU/cm2) also delayed the growth of the pathogen. No increase from inoculated levels was observed during 15 days in antimicrobial alginate films. After 29 days of storage, the lowest counts were obtained in samples packed with zein and alginate films containing enterocins, as well as with zein control films. The most effective treatment for controlling L. monocytogenes during 6 °C storage was vacuum-packaging of sliced cooked ham with alginate films containing 2000 AU/cm2 of enterocins. From the results obtained it can concluded that antimicrobial packaging can improve the safety of sliced cooked ham by delaying and reducing the growth of L. monocytogenes.

Effect of high pressure processing on the microbiology of skin-vacuum packaged sliced meat products: cooked pork ham, dry cured pork ham and marinated beef loin

High hydrostatic pressure is being increasingly investigated in food processing. It causes microbial inactivation and therefore extends the shelf life and enhances the safety of food products. Yeasts, molds, and vegetative cells of bacteria can be inactivated by pressures in the range of 200 to 700 MPa. Microorganisms are more or less sensitive to pressure depending on several factors such as type, strain and the phase or state of the cells. In general, Gram-positive organisms are usually more resistant than Gram-negative. High pressure processing modifies the permeability of the cell membrane, the ion exchange and causes changes in morphology and biochemical reactions, protein denaturations and inhibition of genetic mechanisms. High pressure has been used successfully to extend the shelf life of high-acid foods such as refrigerated fruit juices, jellies and jams. There is now an increasing interest in the use of this technology to extend the shelf life of low-acid foods such as different types of meat products.

Hadronic vacuum polarization and the Lamb shift

Recent improvements in the determination of the running of the fine-structure constant also allow an update of the hadronic vacuum-polarization contribution to the Lamb shift. We find a shift of -3.40(7) kHz to the 1S level of hydrogen. We also comment on the contribution of this effect to the determination by elastic electron scattering of the rms radii of nuclei.

Procedure to characterize microroughness of optical thin films: application to ion-beam-sputtered vacuum-ultraviolet coatings

A method for characterizing the microroughness of samples in optical coating technology is developed. Measurements over different spatial-frequency ranges are composed into a single power spectral density (PSD) covering a large bandwidth. This is followed by the extraction of characteristic parameters through fitting of the PSD to a suitable combination of theoretical models. The method allows us to combine microroughness measurements performed with different techniques, and the fitting procedure can be adapted to any behavior of a combined PSD. The method has been applied to a set of ion-beam-sputtered fluoride vacuum-UV coatings with increasing number of alternative low- and high-index layers. Conclusions about roughness development and microstructural growth are drawn.

Vacuum decay in quantum field theory

We study the contribution to vacuum decay in field theory due to the interaction between the long- and short-wavelength modes of the field. The field model considered consists of a scalar field of mass M with a cubic term in the potential. The dynamics of the long-wavelength modes becomes diffusive in this interaction. The diffusive behavior is described by the reduced Wigner function that characterizes the state of the long-wavelength modes. This function is obtained from the whole Wigner function by integration of the degrees of freedom of the short-wavelength modes. The dynamical equation for the reduced Wigner function becomes a kind of Fokker-Planck equation which is solved with suitable boundary conditions enforcing an initial metastable vacuum state trapped in the potential well. As a result a finite activation rate is found, even at zero temperature, for the formation of true vacuum bubbles of size M-1. This effect makes a substantial contribution to the total decay rate.

Quantum fluctuations on domain walls, strings, and vacuum bubbles

We develop a covariant quantum theory of fluctuations on vacuum domain walls and strings. The fluctuations are described by a scalar field defined on the classical world sheet of the defects. We consider the following cases: straight strings and planar walls in flat space, true vacuum bubbles nucleating in false vacuum, and strings and walls nucleating during inflation. The quantum state for the perturbations is constructed so that it respects the original symmetries of the classical solution. In particular, for the case of vacuum bubbles and nucleating strings and walls, the geometry of the world sheet is that of a lower-dimensional de Sitter space, and the problem reduces to the quantization of a scalar field of tachyonic mass in de Sitter space. In all cases, the root-mean-squared fluctuation is evaluated in detail, and the physical implications are briefly discussed.

Massless minimally coupled fields in de Sitter space: O(4)-symmetric states versus de Sitter invariant vacuum

The issue of de Sitter invariance for a massless minimally coupled scalar field is examined. Formally, it is possible to construct a de Sitterinvariant state for this case provided that the zero mode of the field is quantized properly. Here we take the point of view that this state is physically acceptable, in the sense that physical observables can be computed and have a reasonable interpretation. In particular, we use this vacuum to derive a new result: that the squared difference between the field at two points along a geodesic observers spacetime path grows linearly with the observers proper time for a quantum state that does not break de Sitter invariance. Also, we use the Hadamard formalism to compute the renormalized expectation value of the energy-momentum tensor, both in the O(4)-invariant states introduced by Allen and Follaci, and in the de Sitterinvariant vacuum. We find that the vacuum energy density in the O(4)-invariant case is larger than in the de Sitterinvariant case.

Dissipation, noise and vacuum decay in quantum field theory

We study the process of vacuum decay in quantum field theory focusing on the stochastic aspects of the interaction between long- and short-wavelength modes. This interaction results in a diffusive behavior of the reduced Wigner function describing the state of long-wavelength modes, and thereby to a finite activation rate even at zero temperature. This effect can make a substantial contribution to the total decay rate.

High-pressure processing and antimicrobial biodegradable packaging to control Listeria monocytogenes during storage of cooked ham

The efficiency of combining high-pressure processing (HPP) and active packaging technologies to control Listeria monocytogenes growth during the shelf life of artificially inoculated cooked ham was assessed. Three lots of cooked ham were prepared: control, packaging with alginate films, and packaging with antimicrobial alginate films containing enterocins. After packaging, half of the samples were pressurized. Sliced cooked ham stored at 6 °C experienced a quick growth of L. monocytogenes. Both antimicrobial packaging and pressurization delayed the growth of the pathogen. However, at 6 °C the combination of antimicrobial packaging and HPP was necessary to achieve a reduction of inoculated levels without recovery during 60 days of storage. Further storage at 6 °C of pressurized antimicrobial packed cooked ham resulted in L. monocytogenes levels below the detection limit (day 90). On the other hand, storage at 1 °C controlled the growth of the pathogen until day 39 in non-pressurized ham, while antimicrobial packaging and storage at 1 °C exerted a bacteriostatic effect for 60 days. All HPP lots stored at 1 °C led to counts <100 CFU/g at day 60. Similar results were observed when combining both technologies. After a cold chain break no growth of L. monocytogenes was observed in pressurized ham packed with antimicrobial films, showing the efficiency of combining both technologies.

Active packaging containing nisin and high pressure processing as post-processing listericidal treatments for convenience fermented sausages

Listeria monocytogenes was inoculated on the surface of sliced fermented sausages with no added sodium salt. The pathogen was progressively inactivated during the product shelf life (90 days). Antimicrobial packaging of fermented sausages with PVOH films containing nisin induced a more pronounced reduction of L. monocytogenes counts during refrigerated storage. HPP alone (600 MPa, 5 min, 12 °C) had no antimicrobial effect against L. monocytogenes at the studied conditions. Combination of HPP with antimicrobial packaging did not produce any extra protection against L. monocytogenes compared to antimicrobial packaging alone. The lack of effect of HPP on L. monocytogenes was attributed to a protective effect exerted by the low water activity of the product and its lactate content. These results reflect that antimicrobial packaging with the inclusion of nisin as a natural antimicrobial could be considered as an effective method to reduce the levels of L. monocytogenes in sliced fermented sausages with no added sodium salt

Physical performance of biodegradable films intended for antimicrobial food packaging

Antimicrobial films were prepared by including enterocins to alginate, polyvinyl alcohol (PVOH), and zein films. The physical performance of the films was assessed by measuring color, microstructure (SEM), water vapor permeability (WVP), and tensile properties. All studied biopolymers showed poor WVP and limited tensile properties. PVOH showed the best performance exhibiting the lowest WVP values, higher tensile properties, and flexibility among studied biopolymers. SEM of antimicrobial films showed increased presence of voids and pores as a consequence of enterocin addition. However, changes in microstructure did not disturb WVP of films. Moreover, enterocin-containing films showed slight improvement compared to control films. Addition of enterocins to PVOH films had a plasticizing effect, by reducing its tensile strength and increasing the strain at break. The presence of enterocins had an important effect on tensile properties of zein films by significantly reducing its brittleness. Addition of enterocins, thus, proved not to disturb the physical performance of studied biopolymers. Development of new antimicrobial biodegradable packaging materials may contribute to improving food safety while reducing environmental impact derived from packaging waste.

Deinking flotation of recycled linerboard for food packaging applications

Brown packaging linerboard, made entirely from recovered pulp, was subjected to deinking flotation for evaluating the possible improvements in its chemical, optical and mechanical properties. The increase in the rate of recovered paper utilisation, along with the tendency towards lower basis weights, in the packaging paper production, has created a growing need for the utilisation of secondary fibers of improved quality. To attain better quality fibers, flotation deinking of brown grades is being considered, along with the addition of primary fibers to recovered paper furnish. Numerous conducted studies, in which the flotation technology was used in the treatment of brown grades, support this idea. Most of them show that the quality of fibers is improved after flotation deinking, resulting in higher mechanical properties of the deinked handsheets and in lower amounts of chemical contaminants. As to food and human health safety, packaging paper has to meet specific requirements, to be classified as suitable for its direct contact with foods. Recycled paper and board may contain many potential contaminants, which, especially in the case of direct food contact, may migrate from packaging materials into foodstuffs. In this work, the linerboard sample selected for deinking was made from recycled fibers not submitted previously to chemical deinking flotation. Therefore, the original sample contained many noncellulosic components, as well as the residues of printing inks. The studied linerboardsample was a type of packaging paper used for contact with food products that are usually peeled before use, e.g. fruits and vegetables. The decrease in the amount of chemical contaminants, after conducting deinking flotation, was evaluated, along with the changes in the mechanical and optical properties of the deinked handsheets. Food contact analysis was done on both the original paper samples and the filter pads and handsheets made before and after deinking flotation. Food contact analysis consisted of migration tests of brightening agents, colorants, PCPs, formaldehydes and metals. Microbiological tests were also performed to determine the possible transfer of antimicrobial constituents

Microbial spoilage and quality of marinated dark, firm, dry meat

Estudi elaborat a partir d’una estada al Royal Veterinary and Agricultural University of Denmark entre els mesos de Març a Juny del 2006. S’ha investigat l’efecte dels envasats amb atmosferes modificades (MAP), així com la marinació amb vi tint, sobre l’evolució de la contaminació bacteriològica de carns fosques, dures i seques (DFD). Les carns DFD es troben a les canals d’animals que, abans del sacrifici, han estat exposades a activitats musculars prolongades o estrès. Les carns DFD impliquen importants pèrdues econòmiques degut a la contaminació bacteriològica i als problemes tecnològics relacionats amb la alta capacitat de retenció d’aigua. A més a més, és crític per la indústria investigar la diversitat de la contaminació bacteriana, identificar les espècies bacterianes i controlar-les. Però és difícil degut a la inhabilitat per detectar algunes bactèries en medis coneguts, les interaccions entre elles, la complexitat dels tipus de contaminació com són aigua, terra, femtes i l’ambient. La Polymerasa chain reaction- Denaturating Electrophoresis Gel (PCR-DGEE ) pot sobrepassar aquests problemes reflectint la diversitat microbial i les espècies bacterianes. Els resultants han indicat que la varietat bacteriana de la carn incrementava amb els dies d’envasat independentment del mètode d’envasat, però decreixia significativament amb el tractament de marinació amb vi tint. La DGEE ha mostrat diferències en les espècies trobades, indicant canvis en la contaminació bacteriana i les seves característiques en la carn DFD sota els diferents tractaments. Tot i que la marinació és una bona alternativa i solució a la comercialització de carn DFD , estudis de seqüenciació són necessaris per identificar les diferents tipus de bactèries.

La ramaderia ecològica de boví a les Valls d'Àneu i viabilitat del producte ecològic: de la producció al consum

A les Valls d’Àneu la producció ramadera de boví ecològic és molt important, ja que, actualment, el 22% de les explotacions són ecològiques i es preveu que aquest percentatge augmenti fins al 50% en els propers dos anys. Malgrat això, la motivació principal per a convertir les explotacions convencionals en ecològiques és el factor econòmic, no la consciència ambiental. En l’anàlisi del cicle productiu carni del boví ecològic procedent de les Valls d’Àneu s’ha observat que no hi ha diferències substancials entre la producció ecològica i la convencional. Tot i així, el producte carni de boví ecològic no té gran sortida al mercat, ja que aquest és incipient i, a més, el preu del producte ecològic és molt més elevat que el del convencional. Un aspecte crític de la producció ramadera ecològica és que la seva normativa no considera els impactes ambientals que genera, com són els derivats del transport, la generació de residus d’envasos, etc. En aquest estudi es presenta una aproximació quantitativa dels impactes generats en el cicle productiu carni de boví ecològic de les Valls d’Àneu.