Effect of high pressure processing on the microbiology of skin-vacuum packaged sliced meat products: cooked pork ham, dry cured pork ham and marinated beef loin

High hydrostatic pressure is being increasingly investigated in food processing. It causes microbial inactivation and therefore extends the shelf life and enhances the safety of food products. Yeasts, molds, and vegetative cells of bacteria can be inactivated by pressures in the range of 200 to 700 MPa. Microorganisms are more or less sensitive to pressure depending on several factors such as type, strain and the phase or state of the cells. In general, Gram-positive organisms are usually more resistant than Gram-negative. High pressure processing modifies the permeability of the cell membrane, the ion exchange and causes changes in morphology and biochemical reactions, protein denaturations and inhibition of genetic mechanisms. High pressure has been used successfully to extend the shelf life of high-acid foods such as refrigerated fruit juices, jellies and jams. There is now an increasing interest in the use of this technology to extend the shelf life of low-acid foods such as different types of meat products.

Oxidized oils and dietary zinc and alpha-tocopheryl acetate supplementation: effects on rabbit plasma, liver and meat fatty acid composition and meat Zn, Cu, Fe and Se content

The effects of the addition of heated oils to feeds (3%, w/w) and the dietary supplementation with a-tocopheryl acetate (TA; 100 mg/kg) and Zn (200 mg/kg) on rabbit tissue fatty acid (FA) composition and on the Zn, Cu, Fe and Se content in meat were assessed. Heating unrefined sunflower oil (SO) at 558C for 245 h increased its content in primary oxidation products and reduced its a-tocopherol content. However, this did not significantly affect tissue FA composition. Heating SO at 1408C for 31 h increased its content in secondary oxidation products and in some FA isomers asc9,t11-CLA and di-trans CLA. This led to increases in di-trans CLA in liver and in t9,c12-18:2 in meat. The c9,t11-CLA was the most incorporated CLA isomer in tissues. The dietary supplementation with a-TA did not affect the FA composition of plasma, liver or meat. The cooking of vacuum-packed rabbit meat at 788C for 5 min reduced significantly but slightly its polyunsaturated FA content. The dietary supplementation with Zn did not modify the content of Zn, Fe or Se in meat, but it reduced its Cu content. On the other hand, it increased the content of some FAs in meat when SO heated at 1408C for 31 h was added to feeds.

Microbial spoilage and quality of marinated dark, firm, dry meat

Estudi elaborat a partir d’una estada al Royal Veterinary and Agricultural University of Denmark entre els mesos de Març a Juny del 2006. S’ha investigat l’efecte dels envasats amb atmosferes modificades (MAP), així com la marinació amb vi tint, sobre l’evolució de la contaminació bacteriològica de carns fosques, dures i seques (DFD). Les carns DFD es troben a les canals d’animals que, abans del sacrifici, han estat exposades a activitats musculars prolongades o estrès. Les carns DFD impliquen importants pèrdues econòmiques degut a la contaminació bacteriològica i als problemes tecnològics relacionats amb la alta capacitat de retenció d’aigua. A més a més, és crític per la indústria investigar la diversitat de la contaminació bacteriana, identificar les espècies bacterianes i controlar-les. Però és difícil degut a la inhabilitat per detectar algunes bactèries en medis coneguts, les interaccions entre elles, la complexitat dels tipus de contaminació com són aigua, terra, femtes i l’ambient. La Polymerasa chain reaction- Denaturating Electrophoresis Gel (PCR-DGEE ) pot sobrepassar aquests problemes reflectint la diversitat microbial i les espècies bacterianes. Els resultants han indicat que la varietat bacteriana de la carn incrementava amb els dies d’envasat independentment del mètode d’envasat, però decreixia significativament amb el tractament de marinació amb vi tint. La DGEE ha mostrat diferències en les espècies trobades, indicant canvis en la contaminació bacteriana i les seves característiques en la carn DFD sota els diferents tractaments. Tot i que la marinació és una bona alternativa i solució a la comercialització de carn DFD , estudis de seqüenciació són necessaris per identificar les diferents tipus de bactèries.

Meat quality of ten cattle breeds of the Southwest of Europe

A sample of about 70 young bulls of each of ten beef cattle breeds reared in their typical production systems has been characterised with respect to meat quality traits. Breeds included were Asturiana de los Valles, Asturiana de la Montaña, Avileña-Negra Ibérica, Bruna dels Pirineus, Morucha, Pirenaica and Retinta from Spain, and Aubrac, Gasconne and Salers from France. As was previously showed regarding carcass traits, there exist large differences both between and within breed – systems. In general, rustic breeds tended to present darker and redder meats with higher haematin contents, whereas less precocious and more specialised breeds showed brighter meats with bigger water losses. Protein content was similar, whereas intramuscular fat presented the larger variations both between and within breeds. ICDH content was higher in the more rustic breeds, showing the predominantly oxidative character of their fibres. Texture measurements showed in general large within breed-system variations, the differences between breeds being less evident. Within breed-system, daily gain weight was positively associated with brighter and tender meats. In the range studied, increasing slaughter weight within breed did not have influence on meat quality. Conformation was related to lower water holding capacity and less dry matter and intramuscular fat, as well as to a lower haematin content giving brighter meats. The increase in fatness scores was related to an augment of toughness in meat specialised breeds, although in Avileña-Negra Ibérica breed fatness carcasses were related to more tender meats. Redness parameter a* was positively related to fatter animals and opposed to conformation, the opposite being true for the L* (lightness) parameter. There was a small trend of fatter carcasses to be related to oxidative fibres, whereas the muscular fibres of the more conformed carcasses were more glycolytic. Texture measurements maximum load, maximum stress and toughness were very closely related. Shear force was opposed to tenderness. Losses at cooking were opposed to juiciness, but only in the Spanish breeds. No consistent trends regarding relationships between carcass characteristics and tenderness could be observed. Overall acceptability was primarily related with tenderness and flavour, and later on juiciness.

Bioequivalence of meat products treated with high pressure processing

The effects of high pressure on the composition of food products have not been evaluated extensively. Since, it is necessary to take in consideration the possible effects in basis to the changes induced in the bio molecules by the application of high pressures. The main effect on protein is the denaturation, because the covalent bonds are not affected; however hydrogen bonding, hydrophobic and intermolecular interactions are modified or destroyed. 1 High pressure can modify the activity of some enzymes. If this is done the proteolysis and lipolysis could be more or less intense and the content of free amino acids and fatty acids will be different. This could be related to the bioavailability of these compounds. Low pressures (100 MPa) have been shown to activate some enzymes (monomeric enzymes). Higher pressures induce loss of the enzyme activity. However some enzymes are very stable (ex. Lipase ~ 600 - 1000 MPa). Lipoxygenase is less stable, and there is little information about the effects on antioxidant enzymes. Other important issue is the influence of high pressure on oxidation susceptibility. This could modify the composition of lipids if the degree of the oxidation would have been higher or lower than in the traditional product. Pressure produces the damage of cell membranes favouring the contact between substrates and enzymes, exposure to oxidation of membrane fatty acids and loos of the efficiency of vitamin E. These effects can also affect to protein oxidation. In this study different compounds were analysed to establish the differences between non-treated and high-pressure treated products.

II Workshop on the use of Computed Tomography (CT) in pig carcass classification. Other CT applications: live animals and meat technology, 16-17th April 2009, Monells (Girona), Spain

Es va realitzar el II Workshop en Tomografia Computeritzada (TC) a Monells. El primer dia es va dedicar íntegrament a la utilització del TC en temes de classificació de canals porcines, i el segon dia es va obrir a altres aplicacions del TC, ja sigui en animals vius o en diferents aspectes de qualitat de la carn o els productes carnis. Al workshop hi van assistir 45 persones de 12 països de la UE. The II workshop on the use of Computed Tomography (CT) in pig carcass classification. Other CT applications: live animals and meat technology was held in Monells. The first day it was dedicated to the use of CT in pig carcass classification. The segond day it was open to otehr CT applications, in live animals or in meat and meat products quality. There were 45 assistants of 12 EU countries.

Estimation of lean meat content in pig carcasses using X-ray Computed Tomography and PLS regression

Lean meat percentage (LMP) is an important carcass quality parameter. The aim of this work is to obtain a calibration equation for the Computed Tomography (CT) scans with the Partial Least Square Regression (PLS) technique in order to predict the LMP of the carcass and the different cuts and to study and compare two different methodologies of the selection of the variables (Variable Importance for Projection — VIP- and Stepwise) to be included in the prediction equation. The error of prediction with cross-validation (RMSEPCV) of the LMP obtained with PLS and selection based on VIP value was 0.82% and for stepwise selection it was 0.83%. The prediction of the LMP scanning only the ham had a RMSEPCV of 0.97% and if the ham and the loin were scanned the RMSEPCV was 0.90%. Results indicate that for CT data both VIP and stepwise selection are good methods. Moreover the scanning of only the ham allowed us to obtain a good prediction of the LMP of the whole carcass.

Comparison of different devices for predicting the lean meat percentage of pig carcasses

Lean meat percentage (LMP) is the criterion for carcass classification and it must be measured on line objectively. The aim of this work was to compare the error of the prediction (RMSEP) of the LMP measured with the following different devices: Fat-O-Meat’er (FOM), UltraFOM (UFOM), AUTOFOM and -VCS2000. For this reason the same 99 carcasses were measured using all 4 apparatus and dissected according to the European Reference Method. Moreover a subsample of the carcasses (n=77) were fully scanned with a X-ray Computed Tomography equipment (CT). The RMSEP calculated with cross validation leave-one-out was lower for FOM and AUTOFOM (1.8% and 1.9%, respectively) and higher for UFOM and VCS2000 (2.3% for both devices). The error obtained with CT was the lowest (0.96%) in accordance with previous results, but CT cannot be used on line. It can be concluded that FOM and AUTOFOM presented better accuracy than UFOM and VCS2000.

Effect of magnesium sulphate and L-tryptophan and genotype on the feed intake, behaviour and meat quality of pigs

Sixty-nine entire male pigs with different halothane genotype (homozygous halothane positive – nn –, n=36; and homozygous halothane negative – NN-, n=33) were fed with a supplementation of magnesium sulphate (Mg) and/or L-tryptophan (Trp) in the diet for 5 days before slaughter. Animals were housed individually and were submitted to stressful ante mortem conditions (mixed in the lorry according to treatments and transported 1 hour on rough roads). Individual feed intake was recorded during the 5-d treatment. At the abattoir, pig behaviour was assessed in the raceway to the stunning system and during the stunning period by exposure to CO2. Muscle pH, colour, water holding capacity, texture and cathepsin activities were determined to assess meat quality. The number of pigs with an individual feed intake lower than 2 kg/d was significantly different among diets (P&0.05; Control: 8.7 %; Mg&Trp: 43.5 %; Trp: 17.4 %) and they were considered to have inadequate supplement intake. During the ante mortem period, 15.2 % of pigs included in the experiment died, and this percentage decreased to 8.7 % in those pigs with a feed intake & 2kg/day, all of them from the stress-sensitive pigs (nn). In general, no differences were observed in the behaviour of pigs along the corridor leading to the stunning system and inside the CO2 stunning system. During the stunning procedure, Trp diet showed shorter periods of muscular excitation than control and Mg&Trp diets. The combination of a stressful ante mortem treatment and Mg&Trp supplementation led to carcasses with high incidence of severe skin lesions. Different meat quality results were found when considering all pigs or considering only those with adequate supplement intake. In this later case, Trp increased pH45 (6.15) vs Control diet (5.96) in the Longissimus thoracis (LT) muscle (P&0.05) and pH at 24h (Trp: 5.59 vs C: 5.47) led to a higher incidence of dark, firm and exudative (DFD) traits in SM muscle (P&0.05). Genotype affected negatively all the meat quality traits. Seventy-five percent of LT and 60.0 % of the SM muscles from nn pigs were classified as pale, soft and exudative (PSE), while none of the NN pigs showed these traits (P&0.0001). No significant differences were found between genotypes on the incidence of DFD meat. Due to the negative effects observed in the Mg&Trp group in feed intake and carcass quality, the utilization of a mixture of magnesium sulphate and tryptophan is not recommended.

Quality assurance mechanisms in agrifood: The case of the Spanish fresh meat sector

The largest fresh meat brand names in Spain are analyzed here to studyhow quality is signaled in agribusiness and how the underlying quality-assurance organizations work. Results show, first, that organizationalform varies according to the specialization of the brand name.Publicly-controlled brand names are grounded on market contracting withindividual producers, providing stronger incentives. In contrast,private brands rely more on hierarchy, taking advantage of itssuperiority in solving specific coordination problems. Second, theseemingly redundant coexistence of several quality indicators for agiven product is explained in efficiency terms. Multiple brands areshown to be complementary, given their specialization in guaranteeingdifferent attributes of the product.

Hadronic vacuum polarization and the Lamb shift

Recent improvements in the determination of the running of the fine-structure constant also allow an update of the hadronic vacuum-polarization contribution to the Lamb shift. We find a shift of -3.40(7) kHz to the 1S level of hydrogen. We also comment on the contribution of this effect to the determination by elastic electron scattering of the rms radii of nuclei.

Procedure to characterize microroughness of optical thin films: application to ion-beam-sputtered vacuum-ultraviolet coatings

A method for characterizing the microroughness of samples in optical coating technology is developed. Measurements over different spatial-frequency ranges are composed into a single power spectral density (PSD) covering a large bandwidth. This is followed by the extraction of characteristic parameters through fitting of the PSD to a suitable combination of theoretical models. The method allows us to combine microroughness measurements performed with different techniques, and the fitting procedure can be adapted to any behavior of a combined PSD. The method has been applied to a set of ion-beam-sputtered fluoride vacuum-UV coatings with increasing number of alternative low- and high-index layers. Conclusions about roughness development and microstructural growth are drawn.

Vacuum decay in quantum field theory

We study the contribution to vacuum decay in field theory due to the interaction between the long- and short-wavelength modes of the field. The field model considered consists of a scalar field of mass M with a cubic term in the potential. The dynamics of the long-wavelength modes becomes diffusive in this interaction. The diffusive behavior is described by the reduced Wigner function that characterizes the state of the long-wavelength modes. This function is obtained from the whole Wigner function by integration of the degrees of freedom of the short-wavelength modes. The dynamical equation for the reduced Wigner function becomes a kind of Fokker-Planck equation which is solved with suitable boundary conditions enforcing an initial metastable vacuum state trapped in the potential well. As a result a finite activation rate is found, even at zero temperature, for the formation of true vacuum bubbles of size M-1. This effect makes a substantial contribution to the total decay rate.

Quantum fluctuations on domain walls, strings, and vacuum bubbles

We develop a covariant quantum theory of fluctuations on vacuum domain walls and strings. The fluctuations are described by a scalar field defined on the classical world sheet of the defects. We consider the following cases: straight strings and planar walls in flat space, true vacuum bubbles nucleating in false vacuum, and strings and walls nucleating during inflation. The quantum state for the perturbations is constructed so that it respects the original symmetries of the classical solution. In particular, for the case of vacuum bubbles and nucleating strings and walls, the geometry of the world sheet is that of a lower-dimensional de Sitter space, and the problem reduces to the quantization of a scalar field of tachyonic mass in de Sitter space. In all cases, the root-mean-squared fluctuation is evaluated in detail, and the physical implications are briefly discussed.

Massless minimally coupled fields in de Sitter space: O(4)-symmetric states versus de Sitter invariant vacuum

The issue of de Sitter invariance for a massless minimally coupled scalar field is examined. Formally, it is possible to construct a de Sitterinvariant state for this case provided that the zero mode of the field is quantized properly. Here we take the point of view that this state is physically acceptable, in the sense that physical observables can be computed and have a reasonable interpretation. In particular, we use this vacuum to derive a new result: that the squared difference between the field at two points along a geodesic observers spacetime path grows linearly with the observers proper time for a quantum state that does not break de Sitter invariance. Also, we use the Hadamard formalism to compute the renormalized expectation value of the energy-momentum tensor, both in the O(4)-invariant states introduced by Allen and Follaci, and in the de Sitterinvariant vacuum. We find that the vacuum energy density in the O(4)-invariant case is larger than in the de Sitterinvariant case.