Implicacions diagnòstiques del strem-1 (soluble triggering receptor expressed on myeloid cells) en malalts amb síndrom del distress respiratori agut (sdra) i patologia abdominal. estudi preliminar

Els pacients amb patologia abdominal aguda poden desenvolupar una insuficiència respiratòria secundària a la resposta inflamatòria generada o a una pneumònia nosocomial. El mesurament del “soluble *triggering receptor expressed on myeloid cells 1” (sTREM-1) en líquid alveolar, pleural, sinovial o cefalorraquidi ha demostrat la seva utilitat en el diagnòstic d'infecció. Es va determinar el sTREM-1 alveolar i peritoneal en pacients amb quadre abdominal agut més síndrom de distress respiratori agut (SDRA). Es va concloure que el sTREM-1 és útil per diagnosticar infeccions abdominals i pulmonars en aquests pacients i que la relació sTREM-1 alveolar/peritoneal podria ser útil per determinar el focus infecciós.

Production of nanometric particles in radio frequency glow discharges in mixtures of silane and methane

The formation of silicon particles in rf glow discharges has attracted attention due to their effect as a contaminant during film deposition or etching. However, silicon and silicon alloy powders produced by plasma¿enhanced chemical vapor deposition (PECVD) are promising new materials for sintering ceramics, for making nanoscale filters, or for supporting catalytic surfaces. Common characteristics of these powders are their high purity and the easy control of their stoichiometry through the composition of the precursor gas mixture. Plasma parameters also influence their structure. Nanometric powders of silicon¿carbon alloys exhibiting microstructural properties such as large hydrogen content and high surface/volume ratio have been produced in a PECVD reactor using mixtures of silane and methane at low pressure (-1 Torr) and low frequency square¿wave modulated rf power (13.56 MHz). The a¿Si1¿xCx:H powders were obtained from different precursor gas mixtures, from R=0.05 to R=9, where R=[SiH4]/([SiH4]+[CH4]). The structure of the a¿Si1¿xCx:H powder was analyzed by several techniques. The particles appeared agglomerated, with a wide size distribution between 5 and 100 nm. The silane/methane gas mixture determined the vibrational features of these powders in the infrared. Silicon-hydrogen groups were present for every gas composition, whereas carbon¿hydrogen and silicon¿carbon bonds appeared in methane¿rich mixtures (R-0.6). The thermal desorption of hydrogen revealed two main evolutions at about 375 and 660¿°C that were ascribed to hydrogen bonded to silicon and carbon, respectively. The estimated hydrogen atom concentration in the sample was about 50%.

Soluble models in two-dimensional dilaton gravity

A one-parameter class of simple models of two-dimensional dilaton gravity, which can be exactly solved including back-reaction effects, is investigated at both classical and quantum levels. This family contains the RST model as a special case, and it continuously interpolates between models having a flat (Rindler) geometry and a constant curvature metric with a nontrivial dilaton field. The processes of formation of black hole singularities from collapsing matter and Hawking evaporation are considered in detail. Various physical aspects of these geometries are discussed, including the cosmological interpretation.

Lixiviacion de concentrados de cobre utilizando NaCl y el cobre soluble aportado por el propio concentrado.

Se ha estudiado la lixiviación de concentrados de cobre mediante cloro-complejos cúpricos, generados in situ por la reacción entre el Cu(II) procedente del cobre soluble del concentrado y cloruro de sodio en medio ácido. Se utilizaron concentrados de cobre provenientes de faenas mineras de Antofagasta, Chile. Se ha efectuado una caracterización química y mineralógica de los concentrados originales. Se ha estudiado el efecto de las siguientes variables, durante la lixiviación: concentración de cloruro, concentración de cobre soluble, tiempo de lixiviación, porcentaje de sólidos y temperatura. Se han caracterizado los residuos sólidos por DRX y microscopia electrónica. Los resultados experimentales indican que es posible obtener disoluciones con contenidos de cobre entre 15 y 35 g/l y de 2 a 5 g/l de acidez libre, con características adecuadas para entrar a la etapa de extracción por solventes. El procedimiento utiliza, solo, reactivos comunes y de muy bajo costo, como NaCl y ácido sulfúrico diluido. La ventaja de este procedimiento consiste en recuperar, a muy bajo coste, la totalidad del cobre soluble y entre 10 y 15% del cobre de sulfuros. El residuo final podría pasar a la pirometalurgia convencional

Catalytic gasification of glycerol in supercritical water

The conversion of glycerol in supercritical water (SCW) was studied at 510-550 °C and a pressure of 350 bars using both a bed of inert and non-porous ZrO2 particles (hydrothermal experiments), and a bed of a 1% Ru/ZrO2 catalyst. Experiments were conducted with a glycerol concentration of 5 wt% in a continuous isothermal fixed-bed reactor at a residence time between 2 and 10 s. Hydrothermolysis of glycerol formed water-soluble products such as acetaldehyde, acetic acid, hydroxyacetone and acrolein, and gases like H2, CO and CO2. The catalyst enhanced the formation of acetic acid, inhibited the formation of acrolein, and promoted gasification of the glycerol decomposition products. Hydrogen and carbon oxides were the main gases produced in the catalytic experiments, with minor amounts of methane and ethylene. Complete glycerol conversion was achieved at a residence time of 8.5 s at 510 °C, and at around 5 s at 550 °C with the 1 wt% Ru/ZrO2 catalyst. The catalyst was not active enough to achieve complete gasification since high yields of primary products like acetic acid and acetaldehyde were still present. Carbon balances were between 80 and 60% in the catalytic experiments, decreasing continuously as the residence time was increased. This was attributed partially to the formation of methanol and acetaldehyde, which were not recovered and analyzed efficiently in our set-up, but also to the formation of carbon deposits. Carbon deposition was not observed on the catalyst particles but on the surface of the inert zirconia particles, especially at high residence time. This was related to the higher concentration of acetic acid and other acidic species in the catalytic experiments, which may polymerize to form tar-like carbon precursors. Because of carbon deposition, hydrogen yields were significantly lower than expected; for instance at 550 °C the hydrogen yield potential was only 50% of the stoichiometric value.