Structural and gas-sensing properties of WO3 nanocrystalline powders obtained by a sol-gel method from tungstic acid

WO3 nanocrystalline powders were obtained from tungstic acid following a sol-gel process. Evolution of structural properties with annealing temperature was studied by X-ray diffraction and Raman spectroscopy. These structural properties were compared with those of WO3 nanopowders obtained by the most common process of pyrolysis of ammonium paratungstate, usually used in gas sensors applications. Sol-gel WO3 showed a high sensor response to NO2 and low response to CO and CH4. The response of these sensor devices was compared with that of WO3 obtained from pyrolysis, showing the latter a worse sensor response to NO2. Influence of operating temperature, humidity, and film thickness on NO2 detection was studied in order to improve the sensing conditions to this gas.

Bulk silica-based luminescent materials by sol-gel processing of non-conventional precursors

The sol-gel synthesis of bulk silica-based luminescent materials using innocuous hexaethoxydisilane and hexamethoxydisilane monomers, followed by one hour thermal annealing in an inert atmosphere at 950oC-1150oC, is reported. As-synthesized hexamethoxydisilane-derived samples exhibit an intense blue photoluminescence band, whereas thermally treated ones emit stronger photoluminescence radiation peaking below 600 nm. For hexaethoxydisilane-based material, annealed at or above 1000oC, a less intense photoluminescence band, peaking between 780 nm and 850 nm that is attributed to nanocrystalline silicon is observed. Mixtures of both precursors lead to composed spectra, thus envisaging the possibility of obtaining pre-designed spectral behaviors by varying the mixture composition.

Preparació de materials híbrids orgànico-inorgànics a partir de sals d'imidazoli

Estudi elaborat a partir d’una estada a l’ Ecole Nationale Supérieure de Chimie de Montpellier, França, durant 2006. S’han sintetitzat materials híbrids orgànico-inorgànics mitjançant el procés sol-gel i altres estratègies sintètiques. En alguns casos, s’ha intentat estructurar aquests materials, ja sigui per autoestructuració o per mitjà de tensioactius. Com a catalitzadors de les reaccions d'hidròlisi i policondensació s’han utilitzat àcids, bases i fluorurs. Els materials obtinguts s’han caracteritzat mitjançant diferents tècniques: BET (Brunauer-Emmett-Teller), TEM (microscopia electrònica de transmissió), SEM (microscòpia electrònica de rastreig), raigs X en pols , IR i RMN (ressonància magnètica nuclear) en estat sòlid. Amb aquests materials es pretén preparar catalitzadors heterogenis de Pd per reaccions d’acoblament creuat, i de Ru per reaccions de metàtesi. També s’han sintetitzat sals d'imidazoli amb cadenes hidrocarbonades llargues amb l'objectiu de preparar gels de sílice amb aquestes molècules atrapades dins la matriu inorgànica. Aquests materials s’utilitzaran com a organocatalitzadors i també es prepararan els corresponents catalitzadors de Pd per reaccions de Heck, Suzuki i Sonogashira. Les sals d’imidazoli s’han utilitzat com a tensioactius en la preparació de gels de sílice estructurats. Aquestes molècules han resultat ser cristalls líquids i s’han caracteritzar mitjançant DSC (differential scanning calorimetry), microscopia òptica i raigs X.

Uso de TiO2 dopado con nitrógeno para la generación de hidrógeno bajo irradiación con luz visible

Se desarrollaron catalizadores de TiO2 dopados con nitrógeno para conseguir actividad fotocatalítica bajo irradiación visible. En este trabajo se reporta la síntesis de TiO2-N, usando urea y nitrato de amonio (NH4NO3) como precursores de nitrógeno, tanto a partir de un TiO2 generado in situ (método sol-gel) como mediante la modificación de un TiO2 comercial. Así mismo, se varió la concentración de urea para encontrar el valor óptimo de nitrógeno, lo cual se comprobó mediante la oxidación fotocatalítica de ácido oxálico bajo irradiación con luz visible. Los materiales sintetizados se caracterizaron por medio de análisis elemental, y por reflectancia difusa UV-visible, encontrándose nitrógeno en todas las muestras, y un valor del ancho de banda prohibida en el rango 2-2,8 eV. Lamentablemente, se detectó una pérdida de nitrógeno cuando los fotocatalizadores eran reutilizados, lo cual causó una disminución de su actividad después de cada reacción, ya sea en presencia de oxígeno, o en ausencia de éste mientras se generaba hidrógeno. Entre los dopantes investigados el NH4NO3 mostro una mejor eficiencia en la producción de hidrógeno. Además, los resultados experimentales revelaron claramente que la deposición de platino en la superficie de los catalizadores TiO2-N desempeña un papel fundamental en el aumento de la generación de hidrógeno. Sin embargo, esta mejora dependía claramente del método de preparación de las muestras, obteniéndose mejores resultados con el TiO2-p25.

Síntesis, caracterización y ensayos cinéticos del nanocomposite RuO2/TiO2/MWCNT/Pt en la producción fotocatalítica de combustibles solares bajo iluminación UV y VIS

Se prepararon partículas de nanocomposites basados en TiO2 y nanotubos de carbono multicapa platinizados para la obtención de combustibles solares. Se evaluó la actividad fotocatalítica del material en la producción de hidrógeno, en procesos de degradación de ácido fórmico, y en la obtención de hidrocarburos a partir de la reducción de CO2 en agua. Los nanocomposites fueron sintetizados por medio de la técnica sol-gel. Se estudió el efecto de la proporción y el diámetro de los nanotubos de carbono en la actividad del material bajo iluminación ultravioleta y visible. Se estudió el efecto de la adición de RuO2 (0,5% wt.) en la actividad bajo iluminación visible. Los materiales fueron caracterizados por ATR, XRD, BET, HRTEM y SEM. Se obtuvieron sólidos macroporosos, con contenido de fase anatasa superior al 99% y tamaño cristalino comprendido entre 15 y 21 nm. Los resultados cinéticos mostraron una producción óptima de hidrógeno para el composite TiO2/(5wt.%)MWCNT/Pt(60-80 nm), con eficiencia cuántica y eficiencia energética de 1,27% y 0,27%, respectivamente. En el caso de radiación visible, la producción de hidrógeno fue nula para los composites TiO2/MWCNT/Pt, mientras que para el sistema RuO2/TiO2/MWCNT/Pt se observó que la adicción de MWCNT inhibía la actividad fotocatalítica del composite RuO2/TiO2 en la región del visible. Por otra parte, en los ensayos de reducción de CO2 no se detectó ningún producto de reacción.

Avenços en la preparació d'organosíliques derivades de sals d'imidazoli i de prolinsulfonamides

Durant la última dècada l’organocatàlisi ha suscitat molt d’interès en la comunitat científica. Per una banda, els carbens N-heterocíclics (NHC) són capaços de catalitzar un ampli ventall de reaccions (condensacions benzoíniques, condensacions creuades d’enals amb aldehids o imines, reaccions de Stetter, transesterificacions, reaccions de polimerització,...). Aquesta recerca s’ha centrat en processos homogenis. La inmmobilització de l’organocatalitzador a un suport polimèric insoluble en permetría una fàcil separació per filtració, possibilitant el seu reciclatge. Representa un repte científic que reportaría beneficis des del punt de vista econòmic i medi-ambiental. En aquest treball s’han preparat els monòmers sililats 2 i 6 i les organosíliques M1, M2 i M3 pel procés sol-gel, per a ser assajades en un futur com a organocatalitzadors en fase heterogènia. Per una altra banda, les prolinsulfonamides representen la última incorporació a la família dels derivats de prolina i han mostrat molt bons resultats com a organocatalitzadors quirals en fase homogènia en reaccions aldòliques, addicions de Michael, reaccions de Mannich i d’aza-Diels Alder. Per aquest motiu, i tenint en compte les mateixes raons abans esmentades, en aquest treball es va plantejar la síntesi del mònomer sililat 9 per a poder preparar posteriorment la corresponent organosílica mitjançant el procés sol-gel. La preparació del producte 9 no ha estat possible i s’ha canviat l’estratègia sintètica per tal de sintetitzar un altre monòmer sililat, 16, que s’utilitzarà per la preparació del material corresponent. S’ha fet estudis per obtenir un substrat model 17 a fi de trobar les condicions adients de l’acoblament entre N-Cbz-L-prolina i arilsulfonamides.

Nanopartícules metàl·liques estabilitzades en materials híbrids orgànico-inorgànics. Aplicacions en catàlisi

En el present treball de recerca s’ha reproduït la síntesi de nanopartícules de Rh i Ru estabilitzades en el material híbrid orgànico-inorgànic altament fluorat i s’han realitzat estudis de l’activitat catalítica en les reaccions d’hidrogenacions d’arens i hidròlisi de nitrils respectivament. S’han sintetitzat per primera vegada nanopartícules d’Ir i Os estabilitzades per el material. S’ha assajat l’activitat catàlitica de les nanopartícules d’Ir en la reacció d’alquilació d’amines amb alcohols i la de les nanopartícules d’Os en l’oxidació aeròbica de l’alcohol benzílic i de l’estirè. S’ha sintetitzat un nou monòmer, que mitjançant processos sol-gel ha donat lloc a diversos materials híbrids orgànico-inorgànics i s’han sintetitzat nanopartícules d’Au estabilitzades.

Nanosized Nb-TiO2 gas sensors derived from alkoxides hydrolization

Nanocrystalline TiO2 modified with Nb has been produced through the sol-gel technique. Nanopowders have been obtained by means of the hydrolysis of pure alkoxides with deionized water and peptization of the resulting hydrolysate with diluted acid nitric at 100 C. The addition of Nb stabilizes the anatase phase to higher temperatures. XRD spectra of the undoped and the Nb-doped samples show that the undoped sample has been almost totally converted to rutile at 600 C, meanwhile the doped samples present still a low percentage of rutile phase. Nanocrystalline powders stabilized at 600 C with grain sizes of about 17 nm have successfully been synthesized by the addition of Nb with a concentration of 2% at., which appears to be an adequate additive concentration to improve the gas sensor performances, such as it is suggested by the catalytic conversion efficiency experiments performed from FTIR measurements. FTIR absorbance spectra show that catalytic conversion of CO occurs at lower temperatures when niobium is introduced. The electrical response of the films to different concentrations of CO and ethanol has been monitored in dry and wet environments in order to test the influence of humidity in the sensor response. The addition of Nb decreases the working temperature and increases the stability of the layers. Also, large enhancement of the response time is obtained even with lower working temperatures. Moreover, humidity effects on the gas sensor response toward CO and ethanol are less important in Nb-doped samples than in the undoped ones.

Nanosized Nb-TiO2 gas sensors derived from alkoxides hydrolization

Nanocrystalline TiO2 modified with Nb has been produced through the sol-gel technique. Nanopowders have been obtained by means of the hydrolysis of pure alkoxides with deionized water and peptization of the resulting hydrolysate with diluted acid nitric at 100 C. The addition of Nb stabilizes the anatase phase to higher temperatures. XRD spectra of the undoped and the Nb-doped samples show that the undoped sample has been almost totally converted to rutile at 600 C, meanwhile the doped samples present still a low percentage of rutile phase. Nanocrystalline powders stabilized at 600 C with grain sizes of about 17 nm have successfully been synthesized by the addition of Nb with a concentration of 2% at., which appears to be an adequate additive concentration to improve the gas sensor performances, such as it is suggested by the catalytic conversion efficiency experiments performed from FTIR measurements. FTIR absorbance spectra show that catalytic conversion of CO occurs at lower temperatures when niobium is introduced. The electrical response of the films to different concentrations of CO and ethanol has been monitored in dry and wet environments in order to test the influence of humidity in the sensor response. The addition of Nb decreases the working temperature and increases the stability of the layers. Also, large enhancement of the response time is obtained even with lower working temperatures. Moreover, humidity effects on the gas sensor response toward CO and ethanol are less important in Nb-doped samples than in the undoped ones.

Pilas de combustible soportadas sobre el anodo de una sola camara basadas en electrolitos de ceria dopada con Gd

La utilización de electrolitos soportados en el ánodo es una estrategia muy útil para mejorar las propiedades eléctricas de las pilas de combustible de óxido sólido, debido a que permiten disminuir considerablemente el espesor de los electrolitos. Para este trabajo, se han preparado exitosamente pilas de combustible de óxido sólido con electrolitos de ceria dopada con Gd, Ce1-xGdxO2-y (CGO) soportados sobre un ánodo formado por un cermet de Ni/CGO. Dichas pilas se han instalado y caracterizado en un reactor de una sola cámara donde se ha hecho circular una mezcla de propano y aire. Para ello, se han preparado mezclas de polvos de NiO y de ceria dopada con gadolinia, con diferentes composiciones y tamaño de partículas, para obtener los ánodos con porosidades apropiadas y así utilizarlos como soporte del electrolito en las pilas. Los polvos de los electrolitos de CGO se han preparado por la técnica sol-gel y se han depositado por"dip coating" con diferentes espesores (15-30 ¿m) utilizando una tinta preparada a partir de partículas nanométricas dispersadas en una resina comercial. Los cátodos de La1-xSrxCoO3-S (LSCO) se han preparado también por la técnica sol-gel y se han depositado sobre la capa fina del electrolito. Finalmente, las propiedades eléctricas se han determinado en un reactor de una sola cámara dónde el propano se ha mezclado con aire sintético por encima del límite superior de inflamabilidad. En estas condiciones experimentales se han obtenido altas densidades de potencia estables, controlando las velocidades de flujo total de gas transportador y la presión parcial de propano.

Growth, optical characterization, and laser operation of a stoichiometric crystal KYb(WO4)(2)

We present our recent achievements in the growing and optical characterization of KYb(WO4)2 (hereafter KYbW) crystals and demonstrate laser operation in this stoichiometric material. Single crystals of KYbW with optimal crystalline quality have been grown by the top-seeded-solution growth slow-cooling method. The optical anisotropy of this monoclinic crystal has been characterized, locating the tensor of the optical indicatrix and measuring the dispersion of the principal values of the refractive indices as well as the thermo-optic coefficients. Sellmeier equations have been constructed valid in the visible and near-IR spectral range. Raman scattering has been used to determine the phonon energies of KYbW and a simple physical model is applied for classification of the lattice vibration modes. Spectroscopic studies (absorption and emission measurements at room and low temperature) have been carried out in the spectral region near 1 µm characteristic for the ytterbium transition. Energy positions of the Stark sublevels of the ground and the excited state manifolds have been determined and the vibronic substructure has been identified. The intrinsic lifetime of the upper laser level has been measured taking care to suppress the effect of reabsorption and the intrinsic quantum efficiency has been estimated. Lasing has been demonstrated near 1074 nm with 41% slope efficiency at room temperature using a 0.5 mm thin plate of KYbW. This laser material holds great promise for diode pumped high-power lasers, thin disk and waveguide designs as well as for ultrashort (ps/fs) pulse laser systems.

Ba3Yb(BO3)3 single crystals. Growth and spectroscopic characterization

We obtained Ba3Yb(BO3)3 single crystals by the flux method with solutions of the BaB2O4Na2OYb2O3 system. The evolution of the cell parameters with temperature shows a slope change at temperatures near 873 K, which may indicate a phase transition that is not observed by changes appearing in the x-ray powder patterns or by differential thermal analysis (DTA). The evolution of the diffraction patterns with the temperature shows incongruent melting at temperatures higher than 1473 K. DTA indicates that there is incongruent melting and this process is irreversible. Ba3Yb(BO3)3 has a wide transparency window from 247 to 3900 nm. We recorded optical absorption and emission spectra at room and low temperature, and we determined the splitting of Yb3+ ions. We used the reciprocity method to calculate the maximum emission cross section of 0.28 10-20 cm2 at 966 nm. The calculated lifetime of Yb3+ in Ba3Yb(BO3)3 is trad = 2.62 ms, while the measured lifetime is t = 3.80 ms.

Insulin-Like growth-factor 1 myocardial expression decreases in chronic alcohol consumption

Background Chronic alcohol ingestion may cause severe biochemical and pathophysiological derangements to skeletal muscle. Unfortunately, these alcohol-induced events may also prime skeletal muscle for worsened, delayed, or possibly incomplete repair following acute injury. As alcoholics may be at increased risk for skeletal muscle injury, our goals were to identify the effects of chronic alcohol ingestion on components of skeletal muscle regeneration. To accomplish this, age- and gender-matched C57Bl/6 mice were provided normal drinking water or water that contained 20% alcohol (v/v) for 1820 wk. Subgroups of mice were injected with a 1.2% barium chloride (BaCl2) solution into the tibialis anterior (TA) muscle to initiate degeneration and regeneration processes. Body weights and voluntary wheel running distances were recorded during the course of recovery. Muscles were harvested at 2, 7 or 14 days post-injection and assessed for markers of inflammation and oxidant stress, fiber cross-sectional areas, levels of growth and fibrotic factors, and fibrosis. Results Body weights of injured, alcohol-fed mice were reduced during the first week of recovery. These mice also ran significantly shorter distances over the two weeks following injury compared to uninjured, alcoholics. Injured TA muscles from alcohol-fed mice had increased TNFα and IL6 gene levels compared to controls 2 days after injury. Total protein oxidant stress and alterations to glutathione homeostasis were also evident at 7 and 14 days after injury. Ciliary neurotrophic factor (CNTF) induction was delayed in injured muscles from alcohol-fed mice which may explain, in part, why fiber cross-sectional area failed to normalize 14 days following injury. Gene levels of TGFβ1 were induced early following injury before normalizing in muscle from alcohol-fed mice compared to controls. However, TGFβ1 protein content was consistently elevated in injured muscle regardless of diet. Fibrosis was increased in injured, muscle from alcohol-fed mice at 7 and 14 days of recovery compared to injured controls. Conclusions Chronic alcohol ingestion appears to delay the normal regenerative response following significant skeletal muscle injury. This is evidenced by reduced cross-sectional areas of regenerated fibers, increased fibrosis, and altered temporal expression of well-described growth and fibrotic factors.

Life-time growth patterns of pumpkinseed Lepomis gibbosus introduced to Europe, relative to North American populations

The pumpkinseed Lepomis gibbosus, an omnivorous, nest guarding North American sunfish, was introduced into European waters about 100 years ago. To assess growth performance following introduction, we reviewed the available data for North American and European populations of pumpkinseed and compared the back-calculated age-specific growth for juveniles (standard length, SL, at age two) and adults (age two to five increment) as well as adult body size (SL at age five), von Bertalanffy growth model parameters and the index of growth (in length) performance (φ′). For continental comparisons of growth trajectory, mean growth curves for North American and Europe were calculated with the von Bertalanffy model using pooled data sets for each continent. Juvenile growth rate did not differ between European and North American pumpkinseed, but mean adult body size and adult growth rate were both significantly greater in North American than European populations. Adult body size decreased with increasing latitude (ANOVA) in North American populations, but this was not observed with adult growth rate. In contrast, adult body size tended to increase with latitude in European populations. Adult body size correlated significantly with φ′. The von Bertalanffy model described the overall growth patterns of North American and European populations reasonably well, but on the individual population level, length asymptotes were unrealistic (estimates that were > 20 % of the mean back-calculated size for the oldest age class) for a third of European populations and 80% of the North American populations. In contrast to North American pumpkinseed populations, somatic growth in European populations appears to be compromised by limited, but adequate, food resources, probably due to strong intraspecific interactions. This appears to be especially acute in adults, having potential ramifications for life span and reproductive allocation