Materials selection for superheater tubes in municipal solid waste incineration plants

Corrosion reduces the lifetime of municipal solid waste incineration (MSWI) superheater tubes more than any other cause. It can be minimized by the careful selection of those materials that are most resistant to corrosion under operating conditions. Since thousands of different materials are already known and many more are developed every year, here the selection methodology developed by Prof. Ashby of the University of Cambridge was used to evaluate the performance of different materials to be used as MSWI superheater tubes. The proposed materials can operate at steam pressures and temperatures over 40 bars and 400ºC, respectively. Two case studies are presented: one makes a balanced selection between mechanical properties and cost per thermal unit; and the other focuses on increasing tube lifetime. The balanced selection showed that AISI 410 martensitic stainless steel (wrought, hard tempered) is the best candidate with a good combination of corrosion resistance, a relatively low price (0.83-0.92 e/kg) and a good thermal conductivity (23-27 W/m K). Meanwhile, Nitronic 50/XM-19 stainless steel is the most promising candidate for longterm selection, as it presents high corrosion resistance with a relatively low price (4.86-5.14 e/kg) compared to Ni-alloys.

Why are slip lengths so large in carbon nanotubes?

The enhanced flow in carbon nanotubes is explained using a mathematical model that includes a depletion layer with reduced viscosity near the wall. In the limit of large tubes the model predicts no noticeable enhancement. For smaller tubes the model predicts enhancement that increases as the radius decreases. An analogy between the reduced viscosity and slip-length models shows that the term slip-length is misleading and that on surfaces which are smooth at the nanoscale it may be thought of as a length-scale associated with the size of the depletion region and viscosity ratio. The model therefore provides a physical interpretation of the classical Navier slip condition and explains why `slip-lengths' may be greater than the tube radius.

Control d'una bobinadora automàtica

Un dels problemes típics de regulació en el camp de l’automatització industrial és el control de velocitat lineal d’entrada del fil a les bobines, ja que com més gruix acumulem a igual velocitat de rotació de la bobina s’augmenta notablement la velocitat lineal d’entrada del fil, aquest desajust s’ha de poder compensar de forma automàtica per aconseguir una velocitat d’entrada constant. Aquest problema de regulació de velocitats és molt freqüent i de difícil control a la indústria on intervé el bobinat d’algun tipus de material com cablejat, fil, paper, làmines de planxa, tubs, etc... Els dos reptes i objectius principals són, primer, la regulació de la velocitat de rotació de la bobina per aconseguir una velocitat lineal del fil d’entrada, i segon, mitjançant el guiatge de l’alimentació de fil a la bobina, aconseguir un repartiment uniforme de cada capa de fil. El desenvolupament consisteix amb l’automatització i control d’una bobinadora automàtica mitjançant la configuració i programació de PLC’s, servomotors i encoders. Finalment es farà el muntatge pràctic sobre una bancada per verificar i simular el seu correcte funcionament que ha de donar solució a aquests problemes de regulació de velocitats. Com a conclusions finals s’han aconseguit els objectius i una metodologia per fer una regulació de velocitats de rotació per bobines, amb accionaments de servomotors amb polsos, i a nivell de coneixements he aconseguit dominar les aplicacions d’aquest tipus d’accionaments aplicats a construccions mecàniques.

AMADEUS: advanced manipulation for deep underwater sampling

AMADEUS is a dexterous subsea robot hand incorporating force and slip contact sensing, using fluid filled tentacles for fingers. Hydraulic pressure variations in each of three flexible tubes (bellows) in each finger create a bending moment, and consequent motion or increase in contact force during grasping. Such fingers have inherent passive compliance, no moving parts, and are naturally depth pressure-compensated, making them ideal for reliable use in the deep ocean. In addition to the mechanical design, development of the hand has also considered closed loop finger position and force control, coordinated finger motion for grasping, force and slip sensor development/signal processing, and reactive world modeling/planning for supervisory `blind grasping¿. Initially, the application focus is for marine science tasks, but broader roles in offshore oil and gas, salvage, and military use are foreseen. Phase I of the project is complete, with the construction of a first prototype. Phase I1 is now underway, to deploy the hand from an underwater robot arm, and carry out wet trials with users.

AMADEUS: advanced manipulation for deep underwater sampling

AMADEUS is a dexterous subsea robot hand incorporating force and slip contact sensing, using fluid filled tentacles for fingers. Hydraulic pressure variations in each of three flexible tubes (bellows) in each finger create a bending moment, and consequent motion or increase in contact force during grasping. Such fingers have inherent passive compliance, no moving parts, and are naturally depth pressure-compensated, making them ideal for reliable use in the deep ocean. In addition to the mechanical design, development of the hand has also considered closed loop finger position and force control, coordinated finger motion for grasping, force and slip sensor development/signal processing, and reactive world modeling/planning for supervisory `blind grasping¿. Initially, the application focus is for marine science tasks, but broader roles in offshore oil and gas, salvage, and military use are foreseen. Phase I of the project is complete, with the construction of a first prototype. Phase I1 is now underway, to deploy the hand from an underwater robot arm, and carry out wet trials with users.

Polymer-induced tubulation in lipid vesicles

A mechanism of extraction of tubular membranes from a lipid vesicle is presented. A concentration gradient of anchoring amphiphilic polymers generates tubes from budlike vesicle protrusions. We explain this mechanism in the framework of the Canham-Helfrich model. The energy profile is analytically calculated and a tube with a fixed length, corresponding to an energy minimum, is obtained in a certain regime of parameters. Further, using a phase-field model, we corroborate these results numerically. We obtain the growth of tubes when a polymer source is added, and the budlike shape after removal of the polymer source, in accordance with recent experimental results.

Parity violation in Aharonov-Bohm systems: The spontaneous Hall effect

We show how macroscopic manifestations of P (and T) symmetry breaking can arise in a simple system subject to Aharonov-Bohm interactions. Specifically, we study the conductivity of a gas of charged particles moving through a dilute array of flux tubes. The interaction of the electrons with the flux tubes is taken to be of a purely Aharonov-Bohm type. We find that the system exhibits a nonzero transverse conductivity, i.e., a spontaneous Hall effect. This is in contrast to the fact that the cross sections for both scattering and bremsstrahlung (soft-photon emission) of a single electron from a flux tube are invariant under reflections. We argue that the asymmetry in the conductivity coefficients arises from many-body effects. On the other hand, the transverse conductivity has the same dependence on universal constants that appears in the quantum Hall effect, a result that we relate to the validity of the mean-field approximation.

Rat insulin turnover in vivo

Zucker lean and obese rats were injected under pentobarbital anesthesia with 125I-labeled insulin; at timed intervals from 30 to 120 sec, blood samples were extracted and used for the estimation of insulin levels by RIA. A group of rats from each series was maintained under a constant infusion of noradrenaline. For each insulin determination, a duplicate blood sample containing the same amount of insulin as that used in the RIA, but without the radioactive label, was used as a blank for insulin measurement. The radioactivity in these tubes was then used for the measurement of insulin label per ml blood. From plasma label decay curves and insulin concentrations, the insulin pool size, half-life, and rate of degradation were calculated. Obese rats had higher insulin levels (2.43 nM) and showed less effect of noradrenaline than their lean counterparts, in which insulin distribution volume shrank with noradrenaline treatment. The half-life of plasma insulin was similar in all groups (range, 226-314 sec). Pool size and overall degradation rates were higher in obese (198 femtokatals) than in lean rats (28 femtokatals). It is postulated that obese rats synthesize and cleave much more insulin than lean controls despite their higher circulating levels of insulin.

Plasma leptin turnover rates in lean and obese Zucker rats

Conscious female adult lean and obese Zucker rats were injected through the jugular vein with radioactive iodine-labeled murine leptin; in the ensuing 8 min, four blood samples were sequentially extracted from the carotid artery. The samples were used in a modified RIA for leptin, in which paired tubes received the same amount of either labeled or unlabeled leptin, thus allowing us to estimate both leptin levels and specific radioactivity. The data were used to determine the decay curve parameters from which the half-life of leptin (5.46 ± 0.23 min for lean rats and 6.99 ± 0.75 min for obese rats) as well as the size of its circulating pool (32 pmol/kg for lean rats and 267 pmol/kg for obese rats) and the overall degradation rate (96 fkat/kg for lean rats and 645 fkat/kg for obese rats) were estimated. These values are consistent with the hormonal role of leptin and the need for speedy changes in its levels in response to metabolic challenge.

FiltekTM Silorane and FiltekTM Supreme XT resins: tissue reaction after subcutaneous implantation in isogenic mice

The aim of this study was to evaluate the tissue compatibility of a silorane-based resin system (FiltekTM Silorane) and a methacrylatebased nanoparticle resin (FiltekTM Supreme XT) after implantation in the subcutaneous connective tissue of isogenic mice. One hundred and thirty five male isogenic BALB/c mice were randomly assigned to 12 experimental and 3 control groups, according to the implanted material and the experimental period of 7, 21 and 63 days. At the end of each period, the animals were killed and the tubes with the surrounding tissues were removed and processed for microscopic analysis. Samples were subjected to a descriptive and a semi-quantitative analyses using a 4-point scoring system (0-3) to evaluate the collagen fiber formation and inflammatory infiltrate. Data were statistically analyzed using the Kruskal Wallis test (a=0.05). The results showed that there was no significant difference between the experimental and control groups considering the three evaluation periods (p>0.05). The silorane-based and the methacrylate-based nanoparticle resins presented similar tissue response to that of the empty tube (control group) after subcutaneous implantation in isogenic mice.

Automatització d’una màquina per la fabricació de tubs

Automatització d’una màquina que permeti la fabricació de tubs mitjançant actuadors mecànics que actuen en sintonia amb l’aparellatge elèctric i electrònic responent a un programa realitzat en “Step 7” inserit en un PLC de la sèrie S7-300, el qual respon a una aplicació SCADA per a l’òptima visualització, seguiment i configuració del procés

Morphological and functional variability in the root system of Quercus ilex L. subject to confinement: consequences for afforestation

We examined root morphological and functional differences caused by restrictions imposed to vertical growth in the root system of holm oak (Quercus ilex L.) seedlings to assess the consequences of using nursery containers in the development of a confined root system for this species. Thus, root morphological, topological and functional parameters, including hydraulic conductance per leaf unit surface area (K $_{\rm RL})$, were investigated in one-year seedlings cultivated in three PVC tubes differing in length (20, 60 and 100 cm). Longer tubes showed greater projected root area, root volume, total and fine root lengths, specific root length (SRL) and K$_{\rm RL}$ values than did shorter tubes. On the other hand, the length of coarse roots (diameter > 4.5 mm) and the average root diameter were greater in shorter tubes. The strong positive correlation found between K$_{\rm RL}$ and SRL (r=+0.69; P<0.001) indicated that root thickness was inversely related to water flow through the root system. We concluded that root systems developed in longer tubes are more efficient for plant water uptake and, therefore, changes in root pattern produced in standard forest containers (i.e. about 20 cm length) may in fact prevent a proper establishment of the holm oak in the field, particularly in xeric environments.

Parasitoides de Cacopsylla pyri (L.) (= Psylla pyri (L.)) presentes en una plantación comercial de peral en Lleida no sometida a tratamientos insecticidas

Se ha seguido la evolución de las poblaciones de parasitoides de Cacopsylla pyri (L.) (= Psylla pyri (L.)) en una parcela comercial de peral de la variedad Blanquilla no sometida a tratamientos con productos insecticidas en Lleida. Se recogieron al azar semanalmente unas 150 ninfas de C. pyri desde abril a noviembre de 1991. Las ninfas fueron llevadas al laboratorio y colocadas en brotes de peral. Las momias fueron individualizadas en tubos de cristal hasta la emergencia del adulto del parasitoide. La especie parasitoide más abundante fue el encírtido Trechnites psyllae (Ruschka) (= Metallon psyllae (Ruschka)). También se encontró un encírtido hiperparasitoide, Aphidencyrtus mamitus (Walker) (= Syrphophagus mamitus Walker). Se observó un 18 % de parasitismo en la primera quincena de mayo sobre ninfas de la primera generación de C. pyri, época del año en la que no han hecho su aparición los depredadores de psylla.

Self-expandable metal stents in the treatment of acute esophageal variceal bleeding.

Acute variceal bleeding (AVB) is a life-threatening complication in patients with cirrhosis. Hemostatic therapy of AVB includes early administration of vasoactive drugs that should be combined with endoscopic therapy, preferably banding ligation. However, failure to control bleeding or early rebleed within 5 days still occurs in 15-20% of patients with AVB. In these cases, a second endoscopic therapy may be attempted (mild bleeding in a hemodynamically stable patient) or we can use a balloon tamponade as a bridge to definitive derivative treatment (i.e., a transjugular intrahepatic portosystemic shunt). Esophageal balloon tamponade provides initial control in up to 80% of AVB, but it carries a high risk of major complications, especially in cases of long duration of tamponade (>24 h) and when tubes are inserted by inexperienced staff. Preliminary reports suggest that self-expandable covered esophageal metallic stents effectively control refractory AVB (i.e., ongoing bleeding despite pharmacological and endoscopic therapy or massive bleeding precluding endoscopic therapy) with a low incidence of complications. Thus, covered self-expanding metal stents may represent an alternative to the Sengstaken-Blakemore balloon for the temporary control of bleeding in treatment failures. Further studies are required to determine the role of this new device in AVB.

Control d'una bobinadora automàtica

Un dels problemes típics de regulació en el camp de l’automatització industrial és el control de velocitat lineal d’entrada del fil a les bobines, ja que com més gruix acumulem a igual velocitat de rotació de la bobina s’augmenta notablement la velocitat lineal d’entrada del fil, aquest desajust s’ha de poder compensar de forma automàtica per aconseguir una velocitat d’entrada constant. Aquest problema de regulació de velocitats és molt freqüent i de difícil control a la indústria on intervé el bobinat d’algun tipus de material com cablejat, fil, paper, làmines de planxa, tubs, etc... Els dos reptes i objectius principals són, primer, la regulació de la velocitat de rotació de la bobina per aconseguir una velocitat lineal del fil d’entrada, i segon, mitjançant el guiatge de l’alimentació de fil a la bobina, aconseguir un repartiment uniforme de cada capa de fil. El desenvolupament consisteix amb l’automatització i control d’una bobinadora automàtica mitjançant la configuració i programació de PLC’s, servomotors i encoders. Finalment es farà el muntatge pràctic sobre una bancada per verificar i simular el seu correcte funcionament que ha de donar solució a aquests problemes de regulació de velocitats. Com a conclusions finals s’han aconseguit els objectius i una metodologia per fer una regulació de velocitats de rotació per bobines, amb accionaments de servomotors amb polsos, i a nivell de coneixements he aconseguit dominar les aplicacions d’aquest tipus d’accionaments aplicats a construccions mecàniques.