Parametric analysis of different compact tension specimens for fracture toughness characterisation in woven composite materials

Estudi elaborat a partir d’una estada a l’ Imperial College London, entre juliol i novembre de 2006. En aquest treball s’ha investigat la geometria més apropiada per a la caracterització de la tenacitat a fractura intralaminar de materials compòsits laminats amb teixit. L’objectiu és assegurar la propagació de l’esquerda sense que la proveta falli abans per cap altre mecanisme de dany per tal de permetre la caracterització experimental de la tenacitat a fractura intralaminar de materials compòsits laminats amb teixit. Amb aquesta fi, s’ha dut a terme l’anàlisi paramètrica de diferents tipus de provetes mitjançant el mètode dels elements finits (FE) combinat amb la virtual crack closure technique (VCCT). Les geometries de les provetes analitzades corresponen a la proveta de l’assaig compact tension (CT) i diferents variacions com la extended compact tension (ECT), la proveta widened compact tension (WCT), tapered compact tension (TCT) i doubly-tapered compact tension (2TCT). Com a resultat d’aquestes anàlisis s’han derivat diferents conclusions per obtenir la geometria de proveta més apropiada per a la caracterització de la tenacitat a fractura intralaminar de materials compòsits laminats amb teixit. A més, també s’han dut a terme una sèrie d’assaigs experimentals per tal de validar els resultats de les anàlisis paramètriques. La concordança trobada entre els resultats numèrics i experimentals és bona tot i la presència d’efectes no previstos durant els assaigs experimentals.

Study of the influence of grain size and precipitates on the electromagnetic losses in different grades of non-oriented fully processed electrical steel

The study was performed in the installations of OCAS, a Steel Research Centre of ArcelorMittal. Taking M32 steel (3.25%Si+0.9%Al) as the basis chemical composition and three different thicknesses (0.35, 0.5 and 0.65mm), different annealing conditions (temperature and time) have been applied in the laboratory simulator at St. Chély, France. The aim was to link annealing parameters, grain size and energy loss. It was determined the optimum annealing parameters to reach the lowest power losses for three different grades of non-oriented fully processed electrical steel. In addition, M250-50 samples having different magnetic behaviour (high and low losses) but the same grain size and texture, have been analyzed in terms of TEM observations of their precipitates, in the University of Marseille. The results reveal that a high amount of medium and big precipitates (&10 nm) worsen the magnetic properties of the material. The small precipitates (&10nm) do not have a strong influence on the magnetic properties. The presence of precipitates can have a great influence on the power losses and further work is clearly necessary.

Link between microstructure and properties in new metallurgical concepts for very low loss non-oriented electrical steel

The influence of chemistry and soaking temperature (maximal temperature of the continuous annealing) on the final properties of non-oriented electrical steels has been studied. With this objective two different studies have been performed. First the Mn, Ni and Cr content of a low loss electrical steel composition has been modified. An intermediate content and a high content of each element has been added in order to study the influence of this components on the magnetic looses, grain size and texture. Secondly the influence of the soaking temperature on magnetic properties, grain size and oxidation in four grades of non-oriented electrical steels (Steel A, B, C and D) was studied.

Modelling the cooling of concrete by piped water

Piped water is used to remove hydration heat from concrete blocks during construction. In this paper we develop an approximate model for this process. The problem reduces to solving a one-dimensional heat equation in the concrete, coupled with a first order differential equation for the water temperature. Numerical results are presented and the effect of varying model parameters shown. An analytical solution is also provided for a steady-state constant heat generationmodel. This helps highlight the dependence on certain parameters and can therefore provide an aid in the design of cooling systems.

Estudio del bypass gástrico en Y de Roux y de la gastrectomía tubular sobre el metabolismo de la glucosa y la secreción de hormonas intestinales. Estudio prospectivo y randomizado

Introducció: El bypass gàstric en Y de Roux laparoscòpic (BGYRL) és la tècnica quirúrgica d’elecció per al tractament de l’obesitat mòrbida. La gastrectomia tubular laparoscòpica (GTL) és una tècnica bariàtrica restrictiva amb resultats molt prometedors en relació a la pèrdua de pes, però se’n desconeixen els efectes metabòlics i endocrins. L’objectiu d’aquest estudi és l’avaluació de les diferències en la resposta del metabolisme de la glucosa i la secreció d’hormones intestinals entre ambdós procediments. Material i mètodes: Es va dissenyar un estudi prospectiu i aleatoritzat per la realització del BGYRL i la GTL, ambdós realitzats via laparoscòpica. Totes les pacients es varen avaluar abans, i als 3 i 12 mesos de la intervenció. Se’ls va prendre una mostra de sang venosa després d’un dejuni de 12 hores i als 10 i 60 minuts després de la ingesta d’Ensure® 420 kcal per realitzar les determinacions dels nivells plasmàtics de glucosa, insulina, grelina, leptina, pèptid relacionat amb glucagó (GLP-1), pèptid YY (PYY) i polipèptid pancreàtic (PP). Resultats: Es varen incloure 15 pacients (totes de gènere femení, edat mitja de 48±9 anys, IMC de 44±2.7 kg/m2 amlitat preoperatòria) dels quals 7 van ser aleatoritzats a BGYRL i 8 a GTL. No hi van haver diferències entre ambdós grups en edat, IMC preoperatori, classificació ASA i determinacions hormonals preoperatòries. Després de la cirurgia, s’observa un descens de la glicèmia i insulinèmia, amb una reducció de l´índex HOMA-IR en ambdós grups. Postoperatòriament, es detecta una disminución de les concentracions de la leptina en dejú i després de la ingesta, significativament menor en el grup de BGYRL. Mentre que els nivells de grelina en dejú només descendeixen de forma significativa en el grup de la GTL. Després de la ingesta es produeix una augment dels nivells de GLP-1, significativament major en el grup de BGYRL. Conclusions: Tan el BGYRL como la GTL s’associen a una significativa pèrdua de pes, encara que aquesta fou significativament superior en el BGYRL. Ambdós procediments han millorat notablement l’homeostasi de la glucosa. Només la GTL va rehuir els nivells de grelina tan en dejú com després de la ingesta, mentre que els nivells de GLP-1 i PYY s’elevaren després de la cirurgia, sense diferències estadísticament significatives entre ambdues tècniques.

Estudio prospectivo comparando la gastrectomía tubular laparoscópica y la gastrectomía robótica para el tratamiento de la obesidad mórbida

La cirurgia de l’obesitat suposa una eina dins de l’arsenal terapèutic dels pacients afectes d’obesitat mòrbida. La gastrectomia vertical s’ha popularitzat com a tècnica i les noves tecnologies com la laparoscòpia s’utilitzen de forma habitual. Més recentment la robòtica s’utilitza en diferents àmbits i també s’està implementant en la cirurgia de l’obesitat. A fi de compara la gastrectomia vertical realitzada mitjançant laparoscòpia o robòtica es planteja el següent estudi. S’han comparat els pacients intervinguts de gastrectomia vertical laparoscòpica i robòtica en termes de complicacions intraoperatòries, morbimortalitat i resultats en el seguiment dels pacients. Els resultats són satisfactoris en el sentit que es demostra que la tecnologia robòtica aporta els mateixos resultats en termes de complicacions intra y perioperatòries. Tanmateix es demostra que l’evolució ponderal dels pacients intervinguts de gastrectomia vertical amb tecnologia robòtica es igual a aquells intervinguts de manera tradicional. Així, es conclou que la tecnologia robòtica es una eina en ple desenvolupament que ha demostrat ser eficient, segura y eficaç per al tractament de la Obesitat Mòrbida mitjançant la Gastrectomia vertical.

An assessment of empirical Bayes and composite estimators for small areas

We compare a set of empirical Bayes and composite estimators of the population means of the districts (small areas) of a country, and show that the natural modelling strategy of searching for a well fitting empirical Bayes model and using it for estimation of the area-level means can be inefficient.

Using composite estimators to improve both domain and total area estimation

In this article we propose using small area estimators to improve the estimatesof both the small and large area parameters. When the objective is to estimateparameters at both levels accurately, optimality is achieved by a mixed sampledesign of fixed and proportional allocations. In the mixed sample design, oncea sample size has been determined, one fraction of it is distributedproportionally among the different small areas while the rest is evenlydistributed among them. We use Monte Carlo simulations to assess theperformance of the direct estimator and two composite covariant-freesmall area estimators, for different sample sizes and different sampledistributions. Performance is measured in terms of Mean Squared Errors(MSE) of both small and large area parameters. It is found that the adoptionof small area composite estimators open the possibility of 1) reducingsample size when precision is given, or 2) improving precision for a givensample size.

Solving a concrete sleepers production scheduling by genetic algorithms

PRECON S.A is a manufacturing company dedicated to produce prefabricatedconcrete parts to several industries as rail transportation andagricultural industries.Recently, PRECON signed a contract with RENFE,the Spanish Nnational Rail Transportation Company to manufacturepre-stressed concrete sleepers for siding of the new railways of the highspeed train AVE. The scheduling problem associated with the manufacturingprocess of the sleepers is very complex since it involves severalconstraints and objectives. The constraints are related with productioncapacity, the quantity of available moulds, satisfying demand and otheroperational constraints. The two main objectives are related withmaximizing the usage of the manufacturing resources and minimizing themoulds movements. We developed a deterministic crowding genetic algorithmfor this multiobjective problem. The algorithm has proved to be a powerfuland flexible tool to solve the large-scale instance of this complex realscheduling problem.

Networks of people in specialty production: family firms in the iron and steel Wire industries in Spain (1870-2000)

Capital intensive industries in specialized niches of production have constituted solid ground for family firms in Spain , as evidenced by the experience of the iron and steel wire industries between 1870 and 2000. The embeddedness of these firms in their local and regional environments have allowed the creation of networks that, together with favourable institutional conditions, significantly explain the dominance of family entrepreneurship in iron and steel wire manufacturing in Spain, until the end of the 20 th century. Dominance of family firms at the regional level has not been not an obstacle for innovation in wire manufacturing in Spain, which has taken place even when institutional conditions blocked innovation and traditional networking. Therefore, economic theories about the difficulties dynastic family firms may have to perform appropriately in science-based industries must be questioned

Damn Platonism! Concrete Persons' Skin, Flesh and Bodies: Three Phases of a Won Battle in Miquel Àngel Riera's poetry

The aim of this article is to show how, throughout M. A. Riera's poetry, an evident anti-metaphysical sensibility can be easily detected, which in its turn makes the poet to praise concrete person's skin, flesh and bodies, thus avoiding any personal Platonic or idealistic experience of human love. In the author's opinion, an accurate reading of his poems makes us discover Plato and Platonism as one of the great responsible thinkers for the contempt of carnal love, which has been undoubtedly the origin of a real human pain as a result of denying the somatic side of eros.

Networks of people in specialty production: family firms in the iron and steel Wire industries in Spain (1870-2000)

Capital intensive industries in specialized niches of production have constituted solid ground for family firms in Spain , as evidenced by the experience of the iron and steel wire industries between 1870 and 2000. The embeddedness of these firms in their local and regional environments have allowed the creation of networks that, together with favourable institutional conditions, significantly explain the dominance of family entrepreneurship in iron and steel wire manufacturing in Spain, until the end of the 20 th century. Dominance of family firms at the regional level has not been not an obstacle for innovation in wire manufacturing in Spain, which has taken place even when institutional conditions blocked innovation and traditional networking. Therefore, economic theories about the difficulties dynastic family firms may have to perform appropriately in science-based industries must be questioned

Bond strength of orthodontic brackets using different light and self-curing cements

The purpose of the study was to evaluate the shear bond strength of stainless steel orthodontic brackets directly bonded to extracted human premolar teeth. Fifty teeth were randomly divided into ¿ve groups: (1) System One (chemically cured composite resin), (2) Light Bond (light-cured composite resin), (3) Vivaglass Cem (self-curing glass ionomer cement), (4) Fuji Ortho LC (light-cured glass ionomer cement) used after 37% orthophosphoric acid¿etching of enamel (5) Fuji Ortho LC without orthophosphoric acid¿etching. The brackets were placed on the buccal and lingual surfaces of each tooth, and the specimens were stored in distilled water (24 hours) at 378C and thermocycled. Teeth were mounted on acrylic block frames, and brackets were debonded using an Instron machine. Shear bond strength values at fracture (Nw)were recorded. ANOVA and Student-Newman-Keuls multiple comparison tests were performed (P , .05). Bonding failure site was recorded by stereomicroscope and analyzed by Chi-square test, selected specimens of each group were observed by scanning electron microscope. System One attained the highest bond strength. Light Bond and Fuji Ortho LC, when using an acid-etching technique, obtained bond strengths that were within the range of estimated bond strength values for successful clinical bonding. Fuji Ortho LC and Vivaglass Cem left an almost clean enamel surface after debracketing.

Microfiltración en restauraciones clase II de composite fotopolimerizadas a través de un cono transparente

Estudios clínicos han demostrado la existencia de importantes problemas cuando el composite es utilizado en restauraciones posteriores. Dentro de ellos cabe destacar la contracción del material y la microfiltración. Una adecuada fotopolimerización de la resina influye positivamente en el resultado final de la restauración. La utilización de un cono transparente de plástico ha sido sugerido por algunos autores como un procedimiento para mejorar la fotopolimerización de la resina a nivel del área gingival en las restauraciones clase II de composite, lográndose un aumento en la dureza y nivel de conversión del material, así como una disminución de la brecha entre la restauración y las paredes cavitarias a ese nivel. En el presente trabajo se investigaron los efectos de la utilización del cono transparente propuesto por Ericson en 1987, en la fotopolimerización de la resina y sus consecuencias en la microfiltración. Los resultados mostraron una leve tendencia a la disminución de la microfiltración en el área cervical de las restauraciones clase II cuando el cono fue utilizado, aunque sin diferencias significativas respecto a la técnica convencional.