Evidence of chemical reactions in the hydroxyapatite laser ablation plume with a water atmosphere

The expansion dynamics of the ablation plume generated by KrF laser irradiation of hydroxyapatite targets in a 0.1 mbar water atmosphere has been studied by fast intensified charge coupled device imaging with the aid of optical bandpass filters. The aim of the filters is to isolate the emission of a single species, which allows separate analysis of its expansion. Images obtained without a filter revealed two emissive components in the plume, which expand at different velocities for delay times of up to 1.1 ¿s. The dynamics of the first component is similar to that of a spherical shock wave, whereas the second component, smaller than the first, expands at constant velocity. Images obtained through a 520 nm filter show that the luminous intensity distribution and evolution of emissive atomic calcium is almost identical to those of the first component of the total emission and that there is no contribution from this species to the emission from the second component of the plume. The analysis through a 780 nm filter reveals that atomic oxygen partially diffuses into the water atmosphere and that there is a contribution from this species to the emission from the second component. The last species studied here, calcium oxide, was analyzed by means of a 600 nm filter. The images revealed an intensity pattern more complex than those from the atomic species. Calcium oxide also contributes to the emission from the second component. Finally, all the experiments were repeated in a Ne atmosphere. Comparison of the images revealed chemical reactions between the first component of the plume and the water atmosphere.

Conduction mechanisms and charge storage in Si-nanocrystals metal-oxide-semiconductor memory devices studied with conducting atomic force microscopy

In this work, we demonstrate that conductive atomic force microscopy (C-AFM) is a very powerful tool to investigate, at the nanoscale, metal-oxide-semiconductor structures with silicon nanocrystals (Si-nc) embedded in the gate oxide as memory devices. The high lateral resolution of this technique allows us to study extremely small areas ( ~ 300nm2) and, therefore, the electrical properties of a reduced number of Si-nc. C-AFM experiments have demonstrated that Si-nc enhance the gate oxide electrical conduction due to trap-assisted tunneling. On the other hand, Si-nc can act as trapping centers. The amount of charge stored in Si-nc has been estimated through the change induced in the barrier height measured from the I-V characteristics. The results show that only ~ 20% of the Si-nc are charged, demonstrating that the electrical behavior at the nanoscale is consistent with the macroscopic characterization.

Energy transfer mechanism and Auger effect in Er3+ coupled silicon nanoparticle samples

We report a spectroscopic study about the energy transfer mechanism among silicon nanoparticles (Si-np), both amorphous and crystalline, and Er ions in a silicon dioxide matrix. From infrared spectroscopic analysis, we have determined that the physics of the transfer mechanism does not depend on the Si-np nature, finding a fast (< 200 ns) energy transfer in both cases, while the amorphous nanoclusters reveal a larger transfer efficiency than the nanocrystals. Moreover, the detailed spectroscopic results in the visible range here reported are essential to understand the physics behind the sensitization effect, whose knowledge assumes a crucial role to enhance the transfer rate and possibly employing the material in optical amplifier devices. Joining the experimental data, performed with pulsed and continuous-wave excitation, we develop a model in which the internal intraband recombination within Si-np is competitive with the transfer process via an Auger electron"recycling" effect. Posing a different light on some detrimental mechanism such as Auger processes, our findings clearly recast the role of Si-np in the sensitization scheme, where they are able to excite very efficiently ions in close proximity to their surface. (C) 2010 American Institute of Physics.

Membrane-destabilizing activity of pH-responsive cationic lysine-based surfactants: role of charge position and alkyl chain length

Many strategies for treating diseases require the delivery of drugs into the cell cytoplasm following internalization within endosomal vesicles. Thus, compounds triggered by low pH to disrupt membranes and release endosomal contents into the cytosol are of particular interest. Here, we report novel cationic lysine-based surfactants (hydrochloride salts of N¿- and N¿-acyl lysine methyl ester) that differ in the position of the positive charge and the length of the alkyl chain. Amino acid-based surfactants could be promising novel biomaterials in drug delivery systems, given their biocompatible properties and low cytotoxic potential. We examined their ability to disrupt the cell membrane in a range of pH values, concentrations and incubation times, using a standard hemolysis assay as a model of endosomal membranes. Furthermore, we addressed the mechanism of surfactant-mediated membrane destabilization, including the effects of each surfactant on erythrocyte morphology as a function of pH. We found that only surfactants with the positive charge on the ¿-amino group of lysine showed pH-sensitive hemolytic activity and improved kinetics within the endosomal pH range, indicating that the positive charge position is critical for pH-responsive behavior. Moreover, our results showed that an increase in the alkyl chain length from 14 to 16 carbon atoms was associated with a lower ability to disrupt cell membranes. Knowledge on modulating surfactant-lipid bilayer interactions may help us to develop more efficient biocompatible amino acid-based drug delivery devices.

Glassy magnetic phase driven by short range charge and magnetic ordering in nanocrystalline La1/3Sr2/3FeO3-δ: Magnetization, Mössbauer, and polarized neutron studies

The charge ordered La1/3Sr2/3FeO3−δ (LSFO) in bulk and nanocrystalline forms are investigated using ac and dc magnetization, M¨ossbauer, and polarized neutron studies. A complex scenario of short-range charge and magnetic ordering is realized from the polarized neutron studies in nanocrystalline specimen. This short-range ordering does not involve any change in spin state and modification in the charge disproportion between Fe3+ and Fe5+ compared to bulk counterpart as evident in the M¨ossbauer results. The refinement of magnetic diffraction peaks provides magnetic moments of Fe3+ and Fe5+ are about 3.15 μB and 1.57 μB for bulk, and 2.7 μB and 0.53 μB for nanocrystalline specimen, respectively. The destabilization of charge ordering leads to magnetic phase separation, giving rise to the robust exchange bias (EB) effect. Strikingly, EB field at 5 K attains a value as high as 4.4 kOe for average size ∼70 nm, which is zero for the bulk counterpart. A strong frequency dependence of ac susceptibility reveals cluster-glass-like transition around ∼65 K, below which EB appears. Overall results propose that finite-size effect directs the complex glassy magnetic behavior driven by unconventional short-range charge and magnetic ordering, and magnetic phase separation appears in nanocrystalline LSFO.

Effect of long-range Coulomb interaction on shot-noise suppression in ballistic transport

We present a microscopic analysis of shot-noise suppression due to long-range Coulomb interaction in semiconductor devices under ballistic transport conditions. An ensemble Monte Carlo simulator self-consistently coupled with a Poisson solver is used for the calculations. A wide range of injection-rate densities leading to different degrees of suppression is investigated. A sharp tendency of noise suppression at increasing injection densities is found to scale with a dimensionless Debye length related to the importance of space-charge effects in the structure.

Nano-electro-mechanical in dynamical cellular processes

Report for the scientific sojourn carried out at the Department of Structure and Constituents of Matter during 2007.The main focus of the work was on phenomena related to nano-electromechanical processes that take place on a cellular level. Additionally, it has also been performed independent work related to charge and energy transfer in bio molecules, energy transfer in coupled spin systems as well as electrodynamics of nonlinear metamaterials.

Comparison of different devices for predicting the lean meat percentage of pig carcasses

Lean meat percentage (LMP) is the criterion for carcass classification and it must be measured on line objectively. The aim of this work was to compare the error of the prediction (RMSEP) of the LMP measured with the following different devices: Fat-O-Meat’er (FOM), UltraFOM (UFOM), AUTOFOM and -VCS2000. For this reason the same 99 carcasses were measured using all 4 apparatus and dissected according to the European Reference Method. Moreover a subsample of the carcasses (n=77) were fully scanned with a X-ray Computed Tomography equipment (CT). The RMSEP calculated with cross validation leave-one-out was lower for FOM and AUTOFOM (1.8% and 1.9%, respectively) and higher for UFOM and VCS2000 (2.3% for both devices). The error obtained with CT was the lowest (0.96%) in accordance with previous results, but CT cannot be used on line. It can be concluded that FOM and AUTOFOM presented better accuracy than UFOM and VCS2000.

A doubling measure on R(d) can charge a rectifiable curve

"Vegeu el resum a l'inici del document del fitxer adjunt"

Eines interactives per l'aprenentatge de la dinàmica i el control dels convertidors de potència

El projecte s'ha centrat en el disseny i desenvolupament de laboratoris virtuals per a la docència del dispositius i mètodes de gestió d’energia. Això s’ha realitzat a dos nivells clarament diferenciats, el primer grup de laboratoris correspon als convertidors electrònics de potencia i el segon grup de laboratoris correspon a un conjunt de casos d’aplicacions concretes. En el primer grup es descriu el detall del funcionament dels diferents elements mentre que en el segon els descriuen les idees i conceptes bàsics de funcionament. Els laboratoris virtuals de convertidors electrònics de potència inclouen el convertidor elevador (boost), el convertidor reductor (buck), i convertidors acobladors magnèticament. Aquestes permeten estudiar el comportament dinàmica des d’un punt de vista commutat o bé promitjat, les aplicacions incorporen també la possibilitat de sintonitzar els controladors. Aquestes aplicacions han estat desenvolupades per ser un complement per les sessions de pràctiques presencials. Els laboratoris virtuals d’aplicacions, inclouen els sistema de transport metropolità, el vehicle híbrid i els sistemes de gestió de talls transitoris en el subministrament d’energia principalment. Aquestes laboratoris permeten introduir els estudiants de forma qualitativa en els diferents conceptes i tècniques emprades en els sistemes de generació, transport i transformació d’energia. Totes les aplicacions han estat desenvolupades emprant Easy JAVA Simulations, aquesta eina permet desenvolupar laboratoris multiplataforma fàcilment distribuïbles a través d’internet.

Design of Novel Frequency Generation Circuit with Application to Ultra-Wideband Distributed Oscillators

Given the urgence of a new paradigm in wireless digital trasmission which should allow for higher bit rate, lower latency and tigher delay constaints, it has been proposed to investigate the fundamental building blocks that at the circuital/device level, will boost the change towards a more efficient network architecture, with high capacity, higher bandwidth and a more satisfactory end user experience. At the core of each transciever, there are inherently analog devices capable of providing the carrier signal, the oscillators. It is strongly believed that many limitations in today's communication protocols, could be relieved by permitting high carrier frequency radio transmission, and having some degree of reconfigurability. This led us to studying distributed oscillator architectures which work in the microwave range and possess wideband tuning capability. As microvave oscillators are essentially nonlinear devices, a full nonlinear analyis, synthesis, and optimization had to be considered for their implementation. Consequently, all the most used nonlinear numerical techniques in commercial EDA software had been reviewed. An application of all the aforementioned techniques has been shown, considering a systems of three coupled oscillator ("triple push" oscillator) in which the stability of the various oscillating modes has been studied. Provided that a certain phase distribution is maintained among the oscillating elements, this topology permits a rise in the output power of the third harmonic; nevertheless due to circuit simmetry, "unwanted" oscillating modes coexist with the intenteded one. Starting with the necessary background on distributed amplification and distributed oscillator theory, the design of a four stage reverse mode distributed voltage controlled oscillator (DVCO) using lumped elments has been presented. All the design steps have been reported and for the first time a method for an optimized design with reduced variations in the output power has been presented. Ongoing work is devoted to model a wideband DVCO and to implement a frequency divider.

Elaboració d'un protocol basat en XML per a una xarxa de sensors

La progressiva reducció de dimensió i cost en els dispositius electrònics, la dràstica retallada de consum elèctric i la independència de què això els dota han fet créixer en els últims temps l'interès de les comunitats científiques i tecnològiques per les xarxes sense fils de petits dispositius. Per altra banda, l'XML (eXtensible Markup Language) és un metallenguatge extensible que ha esdevingut un estàndard per a l'intercanvi d'informació estructurada entre diferents plataformes. L'objectiu d'aquest treball és explorar les possibilitats que pot oferir la introducció de l'XML en les xarxes de sensors amb l'elaboració d'un protocol de comunicació basat en aquest llenguatge i demostrar la transparència en el canvi de plataforma. Per fer-ho, es disposa de dos dispositius amb capacitat de comunicació sense fils equipats amb detectors de temperatura, lluminositat, efecte Hall i nivell de càrrega de la bateria. El projecte constarà de dues parts: una, més extensa, dedicada al desenvolupament del programari per a aquests dispositius, encarregat de obtenir les lectures dels diferents sensors i emetre-les per la xarxa utilitzant el llenguatge XML, i una altra, per recollir aquesta informació present a la xarxa, interpretar-la, salvar-la en una base de dades i exposar-la al món en una plana web. El programari dels dispositius sensors s'escriurà en llenguatge nesC dins el sistema tinyOS que és el sistema operatiu que equipen. La part d'explotació de les dades es desenvoluparà sota la plataforma .NET de Microsoft.

Estudio y diseño de filtros pasobanda y en banda dual basados en resonadores microstrip open-loop acoplados

El proyecto está dedicado al estudio y diseño de filtros paso-banda y en banda dual con tecnología microstrip mediante estructuras resonantes de tipo open-loop. Se ha llevado a cabo el diseño de un filtro paso-banda con respuesta Chebyshev, un filtro pasobanda con ceros de transmisión y un filtro de banda dual para WCDMA y WiFi, empleado el método de diseño para filtros basados en resonadores inter-acoplados. Se presentan los modelos eléctricos de los filtros de RF simulados junto con sus respectivos layouts y se comparan las respuestas obtenidas de los dispositivos con las respuestas ideales. En el proyecto se realiza un estudio del comportamiento de los diferentes tipos de acoplamiento entre resonadores open-loop en función de la geometría de la estructura. Las tendencias de comportamiento de los acoplamientos permiten el diseño y colocación de los resonadores para satisfacer las especificaciones del filtro.

Route optimization and customization using real geographical data in Android mobile devices

Nowadays, there are several services and applications that allow users to locate and move to different tourist areas using a mobile device. These systems can be used either by internet or downloading an application in concrete places like a visitors centre. Although such applications are able to facilitate the location and the search for points of interest, in most cases, these services and applications do not meet the needs of each user. This paper aims to provide a solution by studying the main projects, services and applications, their routing algorithms and their treatment of the real geographical data in Android mobile devices, focusing on the data acquisition and treatment to improve the routing searches in off-line environments.

Preventive medicine for epidemic outbreaks and risky behavior through mobile devices and ubiquitous computing

In this work, we have developed the first free software for mobile devices with the Android operating system that can preventively mitigate the number of contagions of sexually transmitted infections (STI), associated with risk behavior. This software runs in two modes. The normal mode allows the user to see the alerts and nearby health centers. The second mode enables the service to work in the background. This software reports the health risks, as well as the location of different test centers.