Report on theorerical results of power generation and conversion

Experimental results of a new controller able to support bidirectional power flow in a full-bridge rectifier with boost-like topology are obtained. The controller is computed using port Hamiltonian passivity techniques for a suitable generalized state space averaging truncation system, which transforms the control objectives, namely constant output voltage dc-bus and unity input power factor, into a regulation problem. Simulation results for the full system show the essential correctness of the simplifications introduced to obtain the controller, although some small experimental discrepancies point to several aspects that need further improvement.

Uranium reserve, nuclear fuel cycle delusion, CO2 emission from the sea, and electricity supply: reflections after the fuel meltdown of Fukushima nuclear power units

The Great Tohoku-Kanto earthquake and resulting tsunami has brought considerable attention to the issue of the construction of new power plants. We argue in this paper, nuclear power is not a sustainable solution to energy problems. First, we explore the stock of uranium-235 and the different schemes developed by the nuclear power industry to exploit this resource. Second, we show that these methods, fast breeder and MOX fuel reactors, are not feasible. Third, we show that the argument that nuclear energy can be used to reduce CO2 emissions is false: the emissions from the increased water evaporation from nuclear power generation must be accounted for. In the case of Japan, water from nuclear power plants is drained into the surrounding sea, raising the water temperature which has an adverse affect on the immediate ecosystem, as well as increasing CO2 emissions from increased water evaporation from the sea. Next, a short exercise is used to show that nuclear power is not even needed to meet consumer demand in Japan. Such an exercise should be performed for any country considering the construction of additional nuclear power plants. Lastly, the paper is concluded with a discussion of the implications of our findings.

Disseny i aplicació del protocol d'instal·lació d'energia fotovoltaica en edificis aïllats de la xarxa elèctrica al PNAP

En el perímetre del parc es troben gran nombre d’edificacions amb mancances de subministrament elèctric per la gran dispersió de la població de la comarca. L’objectiu d’aquest estudi és desenvolupar un protocol per determinar la viabilitat de l’energia fotovoltaica en edificis aïllats i aplicar-la de forma pilot a dos edificis gestionats pels responsables del Parc Natural de l’Alt Pirineu: el Centre de Logística i Manteniment (CLM) i el Refugi del Fornet. Aquests han estat escollits per la seva representativitat com a edificis aïllats de la xarxa elèctrica convencional. S’ha elaborat una metodologia pròpia, el Protocol d’instal·lació d’energia fotovoltaica en edificis aïllats de la xarxa elèctrica. S’ha realitzat una anàlisi de sensibilitats del dimensionat fotovoltaic davant la modificació de diversos paràmetres rellevants. Això ha permès determinar les característiques òptimes de viabilitat per als dos edificis en estudi i el cost de la instal·lació fotovoltaica (17.183€ el CLM i 164.815 € el Refugi del Fornet). Els resultats obtinguts en els dos edificis pilot han mostrat el gran cost relatiu entre l’energia fotovoltaica i l’energia elèctrica produïda a partir de combustibles fòssils.

Instal·lació d'energia fotovoltaica d'una casa de colònies

Els objectius d'aquest projecte són el disseny d'una instal·lació fotovoltaica connectada a xarxa que sigui capaç de produir la mateixa quantitat d’energia que consumeix la casa de colònies a on es troba ubicada. La particularitat d’aquesta instal·lació serà que els generadors fotovoltaics aniran sobra una plataforma giratòria que seguirà el sol buscant sempre la millor i major producció energètica. El control d'aquesta estructura anirà a càrrec d'un autòmat programable. Aprofitant l'existència de panells fotovoltaics, s'ha dissenyat un sistema d’acumulació d’energia de 2 kW de potència que dotarà de corrent una línia que, en cas de falla en el sistema d’alimentació general, es mantindrà ininterrompuda. Aquesta línia serà de 230 V i està dissenyada per tenir una autonomia de 2 hores

Sistematització de la implementació i gestió de sistemes solars a l'Amazònia equatoriana

A l’Amazònia equatoriana existeixen diverses experiències de projectes d’electrificació rural aïllada mitjançant tecnologia solar fotovoltaica els quals estan malmesos i abandonats. Aquest fet no implica que l’energia solar fotovoltaica no sigui una tecnologia apropiada, sinó que mostra que molt sovint no s’han tingut en compte criteris de sostenibilitat i gestió en les etapes de disseny i implementació dels projectes realitzats. El projecte té com a objecte sistematitzar la implementació i gestió de sistemes solars a l’Amazònia equatoriana mitjançant un Manual de Bones Pràctiques. L’abast del projecte comprèn des de la recopilació d’informació sobre l’entorn i problemàtiques dels sistemes solars malmesos, fins a la redacció del propi Manual de Bones Pràctiques. S’estudien tant sistemes d’electrificació individuals com comunitaris

Energy Management for Stand-Alone Renewable Energy Systems (E-MAN-RES). Simulacions de sistemes.

L’objecte del present informe és la descripció dels treballs duts a terme en l’Activitat 2 del projecte E-MAN-RES: models de simulació i càlcul per optimització i anàlisi de sensibilitat de la gestió de la demanda, per part de la Universitat Politècnica de Catalunya.

Análisis de viabilidad técnica-económica del parque eólico Altos de Peralta

RESUMEN La energia eolica se considera una forma indirecta de energia solar. Entre el 1 y 2% de la energia proveniente del sol se convierte en viento, debido al movimiento del aire ocasionado por el desigual calentamiento de la superficie terrestre. La energia cinetica del viento puede transformarse en energia util, tanto mecanica como electrica. La energia eolica, transformada en energia mecanica ha sido historicamente aprovechada, pero su uso para la generacion de energia electrica es mas reciente, en respuesta a la crisis del petroleo y a los impactos ambientales derivados del uso de combustibles. El objetivo principal de este trabajo es hacer un analisis de viabilidad desde un punto de vista tecnico y economico de un parque eolico situado en el municipio de Barasoain (Navarra). Desde el punto de vista tecnico se han estudiado los aspectos constructivos del parque considerando sus diferentes infraestructuras de obra civil y electrica asi como los niveles de recurso eolico. En el ambito economico y financiero se han analizado los aspectos y ratios mas relevantes que definen un proyecto de estas caracteristicas asi como el modelo de financiacion elegida basada en el Project- Finance. Entre las conclusiones mas destacadas de este proyecto cabe destacar la contribucion de la construccion del parque al desarrollo social y economico de la zona donde queda ubicado contribuyendo a la creacion de puestos de trabajo, tanto en la fase de construccion como de explotacion y una perfecta armonia con condicionantes medioambientales de la zona. El analisis tecnico realizado nos indica la viabilidad tecnica del parque tanto desde el punto de vista de recurso eolico como la idoneidad para poder evacuar la energia producida. Por otro lado, los resultados obtenidos cumplen perfectamente con los estandares requeridos por los financiadores de los parques y resultando ser muy atractivos para sus accionistas

Optimal management of microgrids

Desenvolupament dels models matemàtics necessaris per a controlar de forma òptima la microxarxa existent als laboratoris del Institut de Recerca en Energia de Catalunya. Els algoritmes s'implementaran per tal de simular el comportament i posteriorment es programaran directament sobre els elements de la microxarxa per verificar el seu correcte funcionament.. Desenvolupament dels models matemàtics necessaris per a controlar de forma òptima la microxarxa existent als laboratoris del Institut de Recerca en Energia de Catalunya. Els algoritmes s'implementaran per tal de simular el comportament i posteriorment es programaran directament sobre els elements de la microxarxa per verificar el seu correcte funcionament.

Electrical and optical properties of Zn-In-Sn-O transparent conducting thin films

Indium tin oxide (ITO) is one of the widely used transparent conductive oxides (TCO) for application as transparent electrode in thin film silicon solar cells or thin film transistors owing to its low resistivity and high transparency. Nevertheless, indium is a scarce and expensive element and ITO films require high deposition temperature to achieve good electrical and optical properties. On the other hand, although not competing as ITO, doped Zinc Oxide (ZnO) is a promising and cheaper alternative. Therefore, our strategy has been to deposit ITO and ZnO multicomponent thin films at room temperature by radiofrequency (RF) magnetron co-sputtering in order to achieve TCOs with reduced indium content. Thin films of the quaternary system Zn-In-Sn-O (ZITO) with improved electrical and optical properties have been achieved. The samples were deposited by applying different RF powers to ZnO target while keeping a constant RF power to ITO target. This led to ZITO films with zinc content ratio varying between 0 and 67%. The optical, electrical and morphological properties have been thoroughly studied. The film composition was analysed by X-ray Photoelectron Spectroscopy. The films with 17% zinc content ratio showed the lowest resistivity (6.6 × 10 - 4 Ω cm) and the highest transmittance (above 80% in the visible range). Though X-ray Diffraction studies showed amorphous nature for the films, using High Resolution Transmission Electron Microscopy we found that the microstructure of the films consisted of nanometric crystals embedded in a compact amorphous matrix. The effect of post deposition annealing on the films in both reducing and oxidizing atmospheres were studied. The changes were found to strongly depend on the zinc content ratio in the films.

Selective ablation of photovoltaic materials with UV laser sources for monolithic interconnection of devices based on a-Si:H

Lasers are essential tools for cell isolation and monolithic interconnection in thin-film-silicon photovoltaic technologies. Laser ablation of transparent conductive oxides (TCOs), amorphous silicon structures and back contact removal are standard processes in industry for monolithic device interconnection. However, material ablation with minimum debris and small heat affected zone is one of the main difficulty is to achieve, to reduce costs and to improve device efficiency. In this paper we present recent results in laser ablation of photovoltaic materials using excimer and UV wavelengths of diode-pumped solid-state (DPSS) laser sources. We discuss results concerning UV ablation of different TCO and thin-film silicon (a-Si:H and nc-Si:H), focussing our study on ablation threshold measurements and process-quality assessment using advanced optical microscopy techniques. In that way we show the advantages of using UV wavelengths for minimizing the characteristic material thermal affection of laser irradiation in the ns regime at higher wavelengths. Additionally we include preliminary results of selective ablation of film on film structures irradiating from the film side (direct writing configuration) including the problem of selective ablation of ZnO films on a-Si:H layers. In that way we demonstrate the potential use of UV wavelengths of fully commercial laser sources as an alternative to standard backscribing process in device fabrication.

Análisis de viabilidad técnica-económica del parque eólico Altos de Peralta

RESUMEN La energia eolica se considera una forma indirecta de energia solar. Entre el 1 y 2% de la energia proveniente del sol se convierte en viento, debido al movimiento del aire ocasionado por el desigual calentamiento de la superficie terrestre. La energia cinetica del viento puede transformarse en energia util, tanto mecanica como electrica. La energia eolica, transformada en energia mecanica ha sido historicamente aprovechada, pero su uso para la generacion de energia electrica es mas reciente, en respuesta a la crisis del petroleo y a los impactos ambientales derivados del uso de combustibles. El objetivo principal de este trabajo es hacer un analisis de viabilidad desde un punto de vista tecnico y economico de un parque eolico situado en el municipio de Barasoain (Navarra). Desde el punto de vista tecnico se han estudiado los aspectos constructivos del parque considerando sus diferentes infraestructuras de obra civil y electrica asi como los niveles de recurso eolico. En el ambito economico y financiero se han analizado los aspectos y ratios mas relevantes que definen un proyecto de estas caracteristicas asi como el modelo de financiacion elegida basada en el Project- Finance. Entre las conclusiones mas destacadas de este proyecto cabe destacar la contribucion de la construccion del parque al desarrollo social y economico de la zona donde queda ubicado contribuyendo a la creacion de puestos de trabajo, tanto en la fase de construccion como de explotacion y una perfecta armonia con condicionantes medioambientales de la zona. El analisis tecnico realizado nos indica la viabilidad tecnica del parque tanto desde el punto de vista de recurso eolico como la idoneidad para poder evacuar la energia producida. Por otro lado, los resultados obtenidos cumplen perfectamente con los estandares requeridos por los financiadores de los parques y resultando ser muy atractivos para sus accionistas

Automatic generation of active coordinates for quantum dynamics calculations: application to the dynamics of benzene photochemistry

A new practical method to generate a subspace of active coordinates for quantum dynamics calculations is presented. These reduced coordinates are obtained as the normal modes of an analytical quadratic representation of the energy difference between excited and ground states within the complete active space self-consistent field method. At the Franck-Condon point, the largest negative eigenvalues of this Hessian correspond to the photoactive modes: those that reduce the energy difference and lead to the conical intersection; eigenvalues close to 0 correspond to bath modes, while modes with large positive eigenvalues are photoinactive vibrations, which increase the energy difference. The efficacy of quantum dynamics run in the subspace of the photoactive modes is illustrated with the photochemistry of benzene, where theoretical simulations are designed to assist optimal control experiments

Countervailing power? Collusion in markets with decentralized trade

We consider the collective incentives of buyers and sellers to form cartels in markets where trade is realized through decentralized pairwise bargaining. Cartels are coalitions of buyers or sellers that limit market participation and compensate inactive members for abstaining from trade. In a stable market outcome, cartels set Nash equilibrium quantities and cartel memberships are immune to defections. We prove that the set of stable market outcomes is non-empty and we provide its full characterization. Stable market outcomes are of two types: (i) at least one cartel actively restrains trade and the levels of market participation are balanced, or (ii) only one cartel, eventually the cartel that forms on the long side of the market, is active and it reduces trade slightly below the opponent's.

Towards an emotion-driven interactive music system: ridging the gaps between affect, physiology and sound generation

Report for the scientific sojourn at the Stanford University from January until June 2007. Music is well known for affecting human emotional states, yet the relationship between specific musical parameters and emotional responses is still not clear. With the advent of new human-computer interaction (HCI) technologies, it is now possible to derive emotion-related information from physiological data and use it as an input to interactive music systems. Providing such implicit musical HCI will be highly relevant for a number of applications including music therapy, diagnosis, nteractive gaming, and physiologically-based musical instruments. A key question in such physiology-based compositions is how sound synthesis parameters can be mapped to emotional states of valence and arousal. We used both verbal and heart rate responses to evaluate the affective power of five musical parameters. Our results show that a significant correlation exists between heart rate and the subjective evaluation of well-defined musical parameters. Brightness and loudness showed to be arousing parameters on subjective scale while harmonicity and even partial attenuation factor resulted in heart rate changes typically associated to valence. This demonstrates that a rational approach to designing emotion-driven music systems for our public installations and music therapy applications is possible.

Biophysical requirements of power-supply systems: nuclear energy and fossil energy

The report presents a grammar capable of analyzing the process of production of electricity in modular elements for different power-supply systems, defined using semantic and formal categories. In this way it becomes possible to individuate similarities and differences in the process of production of electricity, and then measure and compare “apples” with “apples” and “oranges” with “oranges”. For instance, when comparing the various unit operations of the process of production of electricity with nuclear energy to the analogous unit operations of the process of production of fossil energy, we see that the various phases of the process are the same. The only difference is related to characteristics of the process associated with the generation of heat which are completely different in the two systems. As a matter of facts, the performance of the production of electricity from nuclear energy can be studied, by comparing the biophysical costs associated with the different unit operations taking place in nuclear and fossil power plants when generating process heat or net electricity. By adopting this approach, it becomes possible to compare the performance of the two power-supply systems by comparing their relative biophysical requirements for the phases that both nuclear energy power plants and fossil energy power plants have in common: (i) mining; (ii) refining/enriching; (iii) generating heat/electricity; (iv) handling the pollution/radioactive wastes. This report presents the evaluation of the biophysical requirements for the two powersupply systems: nuclear energy and fossil energy. In particular, the report focuses on the following requirements: (i) electricity; (ii) fossil-fuels, (iii) labor; and (iv) materials.