Spectroscopic characterization of phases formed by high-dose carbon ion implantation in silicon

High-dose carbon-ion-implanted Si samples have been analyzed by infrared spectroscopy, Raman scattering, and x-ray photoelectron spectroscopy (XPS) correlated with transmission electron microscopy. Samples were implanted at room temperature and 500°C with doses between 1017 and 1018 C+/cm2. Some of the samples were implanted at room temperature with the surface covered by a capping oxide layer. Implanting at room temperature leads to the formation of a surface carbon-rich amorphous layer, in addition to the buried implanted layer. The dependence of this layer on the capping oxide suggests this layer to be determined by carbon migration toward the surface, rather than surface contamination. Implanting at 500°C, no carbon-rich surface layer is observed and the SiC buried layer is formed by crystalline ßSiC precipitates aligned with the Si matrix. The concentration of SiC in this region as measured by XPS is higher than for the room-temperature implantation.

Anisotropic surface properties of micro/nanostructured a-C:H:F thin films with self-assembly applications

The singular properties of hydrogenated amorphous carbon (a-C:H) thin filmsdeposited by pulsed DC plasma enhanced chemical vapor deposition (PECVD), such as hardness and wear resistance, make it suitable as protective coating with low surface energy for self-assembly applications. In this paper, we designed fluorine-containing a-C:H (a-C:H:F) nanostructured surfaces and we characterized them for self-assembly applications. Sub-micron patterns were generated on silicon through laser lithography while contact angle measurements, nanotribometer, atomic force microscopy (AFM), and scanning electron microscopy (SEM) were used to characterize the surface. a-C:H:F properties on lithographied surfaces such as hydrophobicity and friction were improved with the proper relative quantity of CH4 and CHF3 during deposition, resulting in ultrahydrophobic samples and low friction coefficients. Furthermore, these properties were enhanced along the direction of the lithographypatterns (in-plane anisotropy). Finally, self-assembly properties were tested with silicananoparticles, which were successfully assembled in linear arrays following the generated patterns. Among the main applications, these surfaces could be suitable as particle filter selector and cell colony substrate.

Blackbody emission under laser excitation of silicon nanopowder produced by plasma-enhanced chemical-vapor deposition

Previous results concerning radiative emission under laser irradiation of silicon nanopowder are reinterpreted in terms of thermal emission. A model is developed that considers the particles in the powder as independent, so under vacuum the only dissipation mechanism is thermal radiation. The supralinear dependence observed between the intensity of the emitted radiation and laser power is predicted by the model, as is the exponential quenching when the gas pressure around the sample increases. The analysis allows us to determine the sample temperature. The local heating of the sample has been assessed independently by the position of the transverse optical Raman mode. Finally, it is suggested that the photoluminescence observed in porous silicon and similar materials could, in some cases, be blackbody radiation

Gas collisions and pressure quenching of the photoluminescence of silicon nanopowder grown by plasma-enhanced chemical vapor deposition

The quenching of the photoluminescence of Si nanopowder grown by plasma-enhanced chemical vapor deposition due to pressure was measured for various gases ( H2, O2, N2, He, Ne, Ar, and Kr) and at different temperatures. The characteristic pressure, P0, of the general dependence I(P)=I0exp(-P/P0) is gas and temperature dependent. However, when the number of gas collisions is taken as the variable instead of pressure, then the quenching is the same within a gas family (mono- or diatomic) and it is temperature independent. So it is concluded that the effect depends on the number of gas collisions irrespective of the nature of the gas or its temperature

Quantification of the bond-angle dispersion by Raman spectroscopy and the strain energy of amorphous silicon

A thorough critical analysis of the theoretical relationships between the bond-angle dispersion in a-Si, Δθ, and the width of the transverse optical Raman peak, Γ, is presented. It is shown that the discrepancies between them are drastically reduced when unified definitions for Δθ and Γ are used. This reduced dispersion in the predicted values of Δθ together with the broad agreement with the scarce direct determinations of Δθ is then used to analyze the strain energy in partially relaxed pure a-Si. It is concluded that defect annihilation does not contribute appreciably to the reduction of the a-Si energy during structural relaxation. In contrast, it can account for half of the crystallization energy, which can be as low as 7 kJ/mol in defect-free a-Si

Relaxation and derelaxation of pure and hydrogenated amorphous silicon during thermal annealing experiments

The structural relaxation of pure amorphous silicon (a-Si) and hydrogenated amorphous silicon (a-Si:H) materials, that occurs during thermal annealing experiments, has been analyzed by Raman spectroscopy and differential scanning calorimetry. Unlike a-Si, the heat evolved from a-Si:H cannot be explained by relaxation of the Si-Si network strain but it reveals a derelaxation of the bond angle strain. Since the state of relaxation after annealing is very similar for pure and hydrogenated materials, our results give strong experimental support to the predicted configurational gap between a-Si and crystalline silicon

Fabricació de Lents Zonals de Fresnel per aplicació als raigs X tous

Estudi elaborat a partir d’una estada al Paul Scherrer Institut del Maig a l’Octubre del 2006 amb l’ajuda i supervisió dels Dr. Konstantins Jefimovs i Dr. Christian David. Focalitzar raigs X tous és una necessitat essencial per al microanàlisis, la microscopia, i fer imatges en moltes Instal·lacions de Radiació Sincrotró. Les Lents Zonals de Fresnel (FZP, de la denominació anglesa “Fresnel Zone Plates”) han demostrat donar uns punts focals amb una resolució espacial destacada i una baixa il·luminació de fons. Tanmateix, la fabricació de FZP és complexa i no totalment reproduïble. A més a més, el temps de vida de les FZP és força curt, ja que estant situades sobre membranes de nitrur de silici molt fines i altament absorbents. Per tant, hem fet esforços per implementar FZP de silici, que s’espera que siguin més resistents. L’element està fet d’una oblia de cristall de silici poc absorbent, i no presenta cap interfase entre materials. Així doncs, aquestes lents són especialment adequades per a aguantar les extremes càrregues de radiació de les fonts de raigs X més brillants. Particularment, això és molt important per a les aplicacions a les pròximes generacions de fonts de raigs X, com els Làsers d’Electrons Lliures (FEL, de la denominació anglesa “Free Electron Laser”). El silici també garanteix que no hi hagi cap banda d’absorció en el rang d’energies de la finestra de l’aigua (200-520 eV), fent aquestes lents ideals per a fer imatges de mostres biològiques. En aquest informe, hi ha una descripció detallada de tots els passos involucrats en la fabricació de les Lents Zonals de Fresnel de silici. En resum, les estructures de FZP es modelen sobre una resina utilitzant litografia per feix d’electrons i llavors el patró es transmet al silici mitjançant un gravat d’ions reactius (RIE, de la denominació anglesa ‘Reactive Ion Etching’) utilitzant una fina (20 nm) màscara de Crintermitja. Les membranes de silici es poden aprimar després de la fabricació de les estructures per a garantir una transmissió suficient fins i tot a baixes energies. Aquest informe també inclou l’anàlisi i la discussió d’alguns experiments preliminars per avaluar el rendiment de les Si FZPs fets a la línia de llum PolLux del Swiss Ligth Source amb l’ajuda dels Dr. Jörg Raabe i Dr. George Tzvetkov.

Simulations of parasitic and intrinsic capacitances related to Multiple-Gate-Field-Effect Transistor architectures

Report for the scientific sojourn carried out at the Université Catholique de Louvain, Belgium, from March until June 2007. In the first part, the impact of important geometrical parameters such as source and drain thickness, fin spacing, spacer width, etc. on the parasitic fringing capacitance component of multiple-gate field-effect transistors (MuGFET) is deeply analyzed using finite element simulations. Several architectures such as single gate, FinFETs (double gate), triple-gate represented by Pi-gate MOSFETs are simulated and compared in terms of channel and fringing capacitances for the same occupied die area. Simulations highlight the great impact of diminishing the spacing between fins for MuGFETs and the trade-off between the reduction of parasitic source and drain resistances and the increase of fringing capacitances when Selective Epitaxial Growth (SEG) technology is introduced. The impact of these technological solutions on the transistor cut-off frequencies is also discussed. The second part deals with the study of the effect of the volume inversion (VI) on the capacitances of undoped Double-Gate (DG) MOSFETs. For that purpose, we present simulation results for the capacitances of undoped DG MOSFETs using an explicit and analytical compact model. It monstrates that the transition from volume inversion regime to dual gate behaviour is well simulated. The model shows an accurate dependence on the silicon layer thickness,consistent withtwo dimensional numerical simulations, for both thin and thick silicon films. Whereas the current drive and transconductance are enhanced in volume inversion regime, our results show thatintrinsic capacitances present higher values as well, which may limit the high speed (delay time) behaviour of DG MOSFETs under volume inversion regime.

Diseño de filtros de onda acústica basados en estructuras "half lattice"

En los últimos tiempos la telefonía móvil ha experimentado una reducción de los terminales gracias a la miniaturización de los filtros a frecuencias de microondas. Los filtros pasa banda más utilizados son los basados en la tecnología SAW, sin embargo son incompatibles con tecnologías de silicio y su comportamiento se degrada a frecuencias superiores de 3 GHz, por ello los estudios actuales se centran en la tecnología BAW. Las dos arquitecturas convencionales de filtros basados en resonadores BAW unidos eléctricamente son el ladder y lattice. Sin embargo, en este proyecto se estudiará la topología half lattice, la cual presenta un mejor comportamiento y unas dimensiones más reducidas. Para ello se obtendrán las ecuaciones de diseño del filtro, y con ellas se realizará la implementación a partir de la frecuencia central y el ancho de banda relativo.

Creació i transmissió de coneixement als clústers empresarials: un model de simulació

Projecte de recerca elaborat a partir d’una estada a l’Snider Entrepreneurial Research Center de la Wharton School de la University of Pennsilvanya y, EUA entre juliol i desembre del 2007. L’objectiu d’aquest projecte és estudiar la relació entre les estratègies de gestió del coneixement i les tecnologies de la informació i la comunicació (TIC) en l’evolució de les poblacions d’organitzacions i els seus efectes en els patrons industrials d’aglomeració espacial. Per a això s’adopta una aproximació fonamentada en la utilització d'un model basats en agents per a obtenir hipòtesis significatives i provables sobre l’evolució de les poblacions d’organitzacions al si de clústers geogràfics. El model de simulació incorpora les perspectives i supòsits d’un marc conceptual, l’Espai de la Informació o I-Space. Això permet una conceptualització basada en la informació de l’entorn econòmic que té en compte les seves dimensions espacials i temporals. Mitjançant els paràmetres del model es dóna la possibilitat d’assignar estratègies específiques de gestió del coneixement als diversos agents i de localitzar-los en una posició de l’espai físic. La simulació mostra com l'adopció d'estratègies diverses pel que fa a la gestió del coneixement influeix en l'evolució de les organitzacions i de la seva localització espacial, i que aquesta evolució es veu modificada pel desenvolupament de les TIC. A través de la modelització de dos casos ben coneguts de clústers geogràfics d’alta tecnologia, com són Silicon Valley a Califòrnia i la Route 128 als voltants de Boston, s’estudia la interrelació entre les estratègies de gestió del coneixement adoptades per les empreses i la seva tria de localització espacial, i també com això és afectat per l’evolució de les tecnologies de la informació i de la comunicació (TIC). Els resultats obtinguts generen una sèrie d’hipòtesis de rica potencialitat sobre l’impacte del desenvolupament de les TIC en la dinàmica d’aquests clusters geogràfics. Concretament, es troba que la estructuració del coneixement i l’aglomeració espacial co-evolucionen i que aquesta coevolució es veu significativament alterada pel desenvolupament de les TIC.

Growth and characterization of CoO ultra thin films

In this report we present the growth process of the cobalt oxide system using reactive electron beam deposition. In that technique, a target of metallic cobalt is evaporated and its atoms are in-flight oxidized in an oxygen rich reactive atmosphere before reaching the surface of the substrate. With a trial and error procedure the deposition parameters have been optimized to obtain the correct stoichiometry and crystalline phase. The evaporation conditions to achieve the correct cobalt oxide salt rock structure, when evaporating over amorphous silicon nitride, are: 525 K of substrate temperature, 2.5·10-4 mbar of oxygen partial pressure and 1 Å/s of evaporation rate. Once the parameters were optimized a set of ultra thin film ranging from samples of 1 nm of nominal thickness to 20nm thick and bulk samples were grown. With the aim to characterize the samples and study their microstructure and morphology, X-ray diffraction, transmission electron microscopy, electron diffraction, energy dispersive X-ray spectroscopy and quasi-adiabatic nanocalorimetry techniques are utilised. The final results show a size dependent effect of the antiferromagnetic transition. Its Néel temperature becomes depressed as the size of the grains forming the layer decreases.

The organization of research corporations and researcher ability

This paper analyzes the formation of Research Corporations as an alternative governance structure for performing R&D compared to pursuing in-house R&D projects. Research Corporations are privatefor-profit research centers that bring together several firms with similar research goals. In a Research Corporation formal authority over the choice of projects is jointly exercised by the top management of the member firms. A private for-profit organization cannot commit not to interfere with the project choice of the researchers. However, increasing the number of member firms of the Research Corporation reduces the incentive of member firms to meddle with the research projects of researchers because exercising formal authority over the choice of research projects is a public good. The Research Corporation thus offers researchers greater autonomy than a single firm pursuing an identical research program in its in-house R&D department. This attracts higher ability researchers to the Research Corporation compared to the internal R&D department. The paper uses the theoretical model to analyze the organization of the Microelectronics and Computer Technology Corporation (MCC). The facts of this case confirm the existence of a tension between control over the choice of research projects and the ability of researchers that the organization is able to attract or hold onto.

When are layoffs acceptable? Evidence from a quasi-experiment

Many authors have discussed a decline in internal labor markets and an apparent shift to a new employment contract, characterized by less commitment between employer and employee and more portable skills. These discussions occur without much evidence on what employment contract employees currently feel is fair. We perfomed quasi-experimental surveys to study when employees in the U.S. andCanada feel that layoffs are fair.Layoffs were perceived as more fair if they were due to lower product demand than if the result of employee suggestions. This result appears to be solely due to norms of reciprocity (companiesshould not punish employees for their efforts), rather than norms of sharing rents, as new technology was also considered a justification for layoffs.Consistent with theories of distributive and procedural equity, layoffs were perceived as more fair if the CEO voluntarily shared the pain. CEO bonuses due to layoffs lowered their reported fairness only slightly.Respondents in Silicon Valley were not more accepting of layoffsthan were those in Canada on average, although the justificationsconsidered valid differed slightly.

Low-loss rib waveguides containing Si nanocrystals embedded in SiO2

We report on the study and modeling of the structural and optical properties of rib-loaded waveguides working in the 600-900-nm spectral range. A Si nanocrystal (Si-nc) rich SiO2 layer with nominal Si excess ranging from 10% to 20% was produced by quadrupole ion implantation of Si into thermal SiO2 formed on a silicon substrate. Si-ncs were precipitated by annealing at 1100°C, forming a 0.4-um-thick core layer in the waveguide. The Si content, the Si-nc density and size, the Si-nc emission, and the active layer effective refractive index were determined by dedicated experiments using x-ray photoelectron spectroscopy, Raman spectroscopy, energy-filtered transmission electron microscopy, photoluminescence and m-lines spectroscopy. Rib-loaded waveguides were fabricated by photolithographic and reactive ion etching processes, with patterned rib widths ranging from 1¿to¿8¿¿m. Light propagation in the waveguide was observed and losses of 11dB/cm at 633 and 780 nm were measured, modeled and interpreted.

Shot-noise suppression in Schottky barrier diodes

We give a theoretical interpretation of the noise properties of Schottky barrier diodes based on the role played by the long range Coulomb interaction. We show that at low bias Schottky diodes display shot noise because the presence of the depletion layer makes the effects of the Coulomb interaction negligible on the current fluctuations. When the device passes from barrier to flat band conditions, the Coulomb interaction becomes active, thus introducing correlation between different current fluctuations. Therefore, the crossover between shot and thermal noise represents the suppression due to long range Coulomb interaction of the otherwise full shot noise. Similar ideas can be used to interpret the noise properties of other semiconductor devices.