Synthesis of triheptanoin and formulation as a solid diet for rodents

Triheptanoin-enriched diets have been successfully used in the experimental treatment of various metabolic disorders. Maximal therapeutic effect is achieved in the context of a ketogenic diet where triheptanoin oil provides 3040% of the daily caloric intake. However, pre-clinical studies using triheptanoin-rich diets are hindered by the difficulty of administering to laboratory animals as a solid foodstuff. In the present study, we successfully synthesized triheptanoin to the highest standards of purity from glycerol and heptanoic acid, using sulfonated charcoal as a catalyst. Triheptanoin oil was then formulated as a solid, stable and palatable preparation using a ketogenic base and a combination of four commercially available formulation agents: hydrophilic fumed silica, hydrophobic fumed silica, microcrystalline cellulose, and talc. Diet compliance and safety was tested on C57Bl/6 mice over a 15-week period, comparing overall status and body weight change. Practical applications: This work provides a complete description of (i) an efficient and cost-effective synthesis of triheptanoin and (ii) its formulation as a solid, stable, and palatable ketogenic diet (triheptanoin-rich; 39% of the caloric intake) for rodents. Triheptanoin-rich diets will be helpful on pre-clinical experiments testing the therapeutic efficacy of triheptanoin in different rodent models of human diseases. In addition, using the same solidification procedure, other oils could be incorporated into rodent ketogenic diet to study their dosage and long-term effects on mammal health and development. This approach could be extremely valuable as ketogenic diet is widely used clinically for epilepsy treatment.

Assessing the pH and DP of canvasses with NIR spectroscopy

The canvas support in easel paintings is composed mainly of cellulose. One of the maindegradation paths of cellulose is acid-catalysed hydrolysis, which means that in an acidic environment (low pH), its degradation proceeds at a faster rate (Strlič et al., 2005).The main effect of acid-catalysed hydrolysis is the breaking up of the polymer chains,measured by the “Degree of Polymerisation” (DP). The lowering of the DP value impliesa lower mechanical strength of the textile (Scicolone, 1993), and thus this parameter canbe used to monitor degradation. Knowing these two parameters can, therefore, be veryinformative regarding the condition of the canvas support.

Synthesis of triheptanoin and formulation as a solid diet for rodents

Triheptanoin-enriched diets have been successfully used in the experimental treatment of various metabolic disorders. Maximal therapeutic effect is achieved in the context of a ketogenic diet where triheptanoin oil provides 3040% of the daily caloric intake. However, pre-clinical studies using triheptanoin-rich diets are hindered by the difficulty of administering to laboratory animals as a solid foodstuff. In the present study, we successfully synthesized triheptanoin to the highest standards of purity from glycerol and heptanoic acid, using sulfonated charcoal as a catalyst. Triheptanoin oil was then formulated as a solid, stable and palatable preparation using a ketogenic base and a combination of four commercially available formulation agents: hydrophilic fumed silica, hydrophobic fumed silica, microcrystalline cellulose, and talc. Diet compliance and safety was tested on C57Bl/6 mice over a 15-week period, comparing overall status and body weight change. Practical applications: This work provides a complete description of (i) an efficient and cost-effective synthesis of triheptanoin and (ii) its formulation as a solid, stable, and palatable ketogenic diet (triheptanoin-rich; 39% of the caloric intake) for rodents. Triheptanoin-rich diets will be helpful on pre-clinical experiments testing the therapeutic efficacy of triheptanoin in different rodent models of human diseases. In addition, using the same solidification procedure, other oils could be incorporated into rodent ketogenic diet to study their dosage and long-term effects on mammal health and development. This approach could be extremely valuable as ketogenic diet is widely used clinically for epilepsy treatment.

Low environmental impact bleaching sequences for attaining high brightness level with eucalyptus SPP pulp

The alternatives used for minimizing the usage of chlorine dioxide in bleaching sequences included a hot acid hydrolysis (Ahot) stage, the use of hot chlorine dioxide (Dhot) and ozone stages at medium consistency and high consistency (Zmc and Zhc), in addition to stages with atmospheric hydrogen peroxide (P) and pressurized hydrogen peroxide (PO). The results were interpreted based on the cost of the chemical products, bleaching process yields and on minimizing the environmental impact of the bleaching process. In spite of some process restrictions, high ISO brightness levels were kept around 90 % brightness. Additionally, the inclusion of stages like acid hydrolysis, pressurized peroxide and ozone in the bleaching sequences provided an increase in operating flexibility, aimed at reducing environmental impact (ECF Light). The Dhot(EOP)D(PO) sequence presented lower operating cost for ISO brightness above 92 %. However, this kind of sequence was not allowed for closing the wastewater circuit, even partially. For ISO brightness level around 91%, the AhotZhcDP sequence presented a lower operating cost than the others

Silicon quantum dots embedded in a SiO2 matrix: From structural study to carrier transport properties

We study the details of electronic transport related to the atomistic structure of silicon quantum dots embedded in a silicon dioxide matrix using ab initio calculations of the density of states. Several structural and composition features of quantum dots (QDs), such as diameter and amorphization level, are studied and correlated with transport under transfer Hamiltonian formalism. The current is strongly dependent on the QD density of states and on the conduction gap, both dependent on the dot diameter. In particular, as size increases, the available states inside the QD increase, while the QD band gap decreases due to relaxation of quantum confinement. Both effects contribute to increasing the current with the dot size. Besides, valence band offset between the band edges of the QD and the silica, and conduction band offset in a minor grade, increases with the QD diameter up to the theoretical value corresponding to planar heterostructures, thus decreasing the tunneling transmission probability and hence the total current. We discuss the influence of these parameters on electron and hole transport, evidencing a correlation between the electron (hole) barrier value and the electron (hole) current, and obtaining a general enhancement of the electron (hole) transport for larger (smaller) QD. Finally, we show that crystalline and amorphous structures exhibit enhanced probability of hole and electron current, respectively.

Microstructural evolution of primary crystallization in diffusion-controlled grain growth

A model has been developed for evaluating grain size distributions in primary crystallizations where the grain growth is diffusion controlled. The body of the model is grounded in a recently presented mean-field integration of the nucleation and growth kinetic equations, modified conveniently in order to take into account a radius-dependent growth rate, as occurs in diffusion-controlled growth. The classical diffusion theory is considered, and a modification of this is proposed to take into account interference of the diffusion profiles between neighbor grains. The potentiality of the mean-field model to give detailed information on the grain size distribution and transformed volume fraction for transformations driven by nucleation and either interface- or diffusion-controlled growth processes is demonstrated. The model is evaluated for the primary crystallization of an amorphous alloy, giving an excellent agreement with experimental data. Grain size distributions are computed, and their properties are discussed.

Thermally-Induced Structural Transformations on Polymorphous Silicon

Polymorphous Si is a nanostructured form of hydrogenated amorphous Si that contains a small fraction of Si nanocrystals or clusters. Its thermally induced transformations such as relaxation, dehydrogenation, and crystallization have been studied by calorimetry and evolved gas analysis as a complementary technique. The observed behavior has been compared to that of conventional hydrogenated amorphous Si and amorphous Si nanoparticles. In the temperature range of our experiments (650700 C), crystallization takes place at almost the same temperature in polymorphous and in amorphous Si. In contrast, dehydrogenation processes reflect the presence of different hydrogen states. The calorimetry and evolved gas analysis thermograms clearly show that polymorphous Si shares hydrogen states of both amorphous Si and Si nanoparticles. Finally, the total energy of the main SiH group present in polymorphous Si has been quantified

Enhancement of oxidation rate of a-Si nanoparticles during dehydrogenation

Oxidation of amorphous silicon (a-Si) nanoparticles grown by plasma-enhanced chemical vapor deposition were investigated. Their hydrogen content has a great influence on the oxidation rate at low temperature. When the mass gain is recorded during a heating ramp in dry air, an oxidation process at low temperature is identified with an onset around 250°C. This temperature onset is similar to that of hydrogen desorption. It is shown that the oxygen uptake during this process almost equals the number of hydrogen atoms present in the nanoparticles. To explain this correlation, we propose that oxidation at low temperature is triggered by the process of hydrogen desorption

Selective ablation of photovoltaic materials with UV laser sources for monolithic interconnection of devices based on a-Si:H

Lasers are essential tools for cell isolation and monolithic interconnection in thin-film-silicon photovoltaic technologies. Laser ablation of transparent conductive oxides (TCOs), amorphous silicon structures and back contact removal are standard processes in industry for monolithic device interconnection. However, material ablation with minimum debris and small heat affected zone is one of the main difficulty is to achieve, to reduce costs and to improve device efficiency. In this paper we present recent results in laser ablation of photovoltaic materials using excimer and UV wavelengths of diode-pumped solid-state (DPSS) laser sources. We discuss results concerning UV ablation of different TCO and thin-film silicon (a-Si:H and nc-Si:H), focussing our study on ablation threshold measurements and process-quality assessment using advanced optical microscopy techniques. In that way we show the advantages of using UV wavelengths for minimizing the characteristic material thermal affection of laser irradiation in the ns regime at higher wavelengths. Additionally we include preliminary results of selective ablation of film on film structures irradiating from the film side (direct writing configuration) including the problem of selective ablation of ZnO films on a-Si:H layers. In that way we demonstrate the potential use of UV wavelengths of fully commercial laser sources as an alternative to standard backscribing process in device fabrication.

Análisis de sistemas bucoadhesivos

[spa]Objetivo: El objetivo de este estudio es el diseño de un parche bucoadhesivo para la administración transbucal de clorhidrato de doxepina utilizando diferentes polímeros así como la caracterización de dichos sistemas en cuanto al análisis calorimétrico y la capacidad de hinchamiento.Materiales y métodos: Se ha utilizado clorhidrato de doxepina y diferentes polímeros, carboximetilcelulosa sódica, hidroxipropilmetilcelulosa y chitosan. La calorimetría diferencial de barrido (DSC) se ha realizado en un dispositivo Mettler FP 80 equipado con un horno FP 85 y la capacidad de hinchamiento utilizando placas de agar.Resultados: Se obtienen termogramas de los parches y las mezclas físicas donde se observan transiciones endotérmicas entre 30 y 120º C y el pico endotérmico del principio activo en las mezclas físicas binarias. La entalpía de deshidratación es similar en los polímeros de carboximetilcelulosa sódica y chitosan (281 J/g) siendo menor en la película de hidroxipropilmetilcelulosa (251 J/g), al igual que el porcentaje de hidratación donde se demuestra que los parches elaborados con hidroxipropilmetilcelulosa presenta menor tendencia a captar agua (55,91 %) frente al 67,04 % y 67,30 % de la carboximetilcelulosa sódica y chitosan, respectivamente.Conclusión: Los resultados obtenidos muestran que existe compatibilidad entre los componentes de la formulación y los datos de entalpía se correlacionan con los datos obtenidos en el ensayo de hinchamiento.[eng]The aim of this study is to design a bucoadhesive patch for the transbuccal administration of doxepin hydrochloride using different polymers as well as the characterization of these systems for calorimetric analysis and the swelling capacity. Materials and methods: Doxepin hydrochloride was used as well as various polymers; carboxymethylcellulose sodium, hydroxypropylmethyl cellulose and chitosan. Differential scanning calorimetry (DSC) was carried out using a Mettler FP 80 device equipped with a FP 85 oven and the swelling capacity using agar plates. Results: Thermograms obtained patches and physical mixtures where there are endothermic transitions between 30 and 120º C and the endothermic peak of the active principle in binary physical mixtures. Dehydration enthalpy is similar in polymers of carboxymethylcellulose sodium and chitosan (281 J/g), the film having less hydroxypropylmethylcellulose (251 J/g), the percentage of moisture shows that the patches prepared with hydroxypropylmethylcellulose have less tendency to collect water (55.91 %) compared to 67.04 % and 67.30 % with sodium carboxymethylcellulose and chitosan, respectively. Conclusion: The results show that there is compatibility between the components of the formulation and the enthalpy data correlate

Evolución estacional de δ13C en hojas y madera de dos quercíneas mediterráneas concurrentes (Quercus ilex subps. ballota L. y Quercus faginea Lam.): dinámica de la eficiencia en uso del agua

En el ámbito mediterráneo es frecuente la concurrencia en un mismo hábitat de especies perennifolias y caducifolias como Quercus ilex y Q. faginea. En este estudio se pretende analizar la diferencia en la respuesta ecofisiológica de las dos especies frente a la variación climática estacional mediante la composición isotópica de carbono de la materia orgánica soluble de las hojas (δ13Ch) y de la α-celulosa de la madera (δ13Cm). Se observaron patrones intraanuales dependientes de la especie en la δ13Ch. Por un lado, Q. faginea utiliza reservas de almidón como fuente de carbono para producir nuevas hojas a principios de abril, dando lugar a valores altos de δ13Ch. Por otro, Q. ilex utiliza asimilados recientes de las hojas formadas el año anterior (aún funcionales). No obstante, los valores globales de δ13Ch en ambas especies son similares (-25,4±0,55 y -25,5±0,89, para Q. faginea y Q. ilex, respectivamente), lo que apunta a valores equivalentes de eficiencia intrínseca en el uso del agua. Como en las hojas, la δ13Cm de Q. faginea reflejó claramente el uso de reservas en la madera temprana. Tanto la δ13Ch como la δ13Cm de las dos especies registran ajustes como respuesta a las variaciones ambientales estacionales. No obstante, y como parámetro integrador de eficiencia hídrica, la menor amplitud de las variaciones en la δ13Cm de Q. ilex sugiere una menor sensibilidad de esta especie frente a las fluctuaciones climáticas, lo que puede otorgarle cierta ventaja competitiva bajo condiciones de incremento progresivo de aridez.

Progress in a-Si:H/c-Si heterojunction emitters obtained by Hot-Wire CVD at 200°C

In this work, we investigate heterojunction emitters deposited by Hot-Wire CVD on p-type crystalline silicon. The emitter structure consists of an n-doped film (20 nm) combined with a thin intrinsic hydrogenated amorphous silicon buffer layer (5 nm). The microstructure of these films has been studied by spectroscopic ellipsometry in the UV-visible range. These measurements reveal that the microstructure of the n-doped film is strongly influenced by the amorphous silicon buffer. The Quasy-Steady-State Photoconductance (QSS-PC) technique allows us to estimate implicit open-circuit voltages near 700 mV for heterojunction emitters on p-type (0.8 Ω·cm) FZ silicon wafers. Finally, 1 cm 2 heterojunction solar cells with 15.4% conversion efficiencies (total area) have been fabricated on flat p-type (14 Ω·cm) CZ silicon wafers with aluminum back-surface-field contact.

Synthesis of triheptanoin and formulation as a solid diet for rodents

Triheptanoin-enriched diets have been successfully used in the experimental treatment of various metabolic disorders. Maximal therapeutic effect is achieved in the context of a ketogenic diet where triheptanoin oil provides 30-40% of the daily caloric intake. However, pre-clinical studies using triheptanoin-rich diets are hindered by the difficulty of administering to laboratory animals as a solid foodstuff. In the present study, we successfully synthesized triheptanoin to the highest standards of purity from glycerol and heptanoic acid, using sulfonated charcoal as a catalyst. Triheptanoin oil was then formulated as a solid, stable and palatable preparation using a ketogenic base and a combination of four commercially available formulation agents: hydrophilic fumed silica, hydrophobic fumed silica, microcrystalline cellulose, and talc. Diet compliance and safety was tested on C57Bl/6 mice over a 15-week period, comparing overall status and body weight change. Practical applications: This work provides a complete description of (i) an efficient and cost-effective synthesis of triheptanoin and (ii) its formulation as a solid, stable, and palatable ketogenic diet (triheptanoin-rich; 39% of the caloric intake) for rodents. Triheptanoin-rich diets will be helpful on pre-clinical experiments testing the therapeutic efficacy of triheptanoin in different rodent models of human diseases. In addition, using the same solidification procedure, other oils could be incorporated into rodent ketogenic diet to study their dosage and long-term effects on mammal health and development. This approach could be extremely valuable as ketogenic diet is widely used clinically for epilepsy treatment.

Synthesis of triheptanoin and formulation as a solid diet for rodents

Triheptanoin-enriched diets have been successfully used in the experimental treatment of various metabolic disorders. Maximal therapeutic effect is achieved in the context of a ketogenic diet where triheptanoin oil provides 30-40% of the daily caloric intake. However, pre-clinical studies using triheptanoin-rich diets are hindered by the difficulty of administering to laboratory animals as a solid foodstuff. In the present study, we successfully synthesized triheptanoin to the highest standards of purity from glycerol and heptanoic acid, using sulfonated charcoal as a catalyst. Triheptanoin oil was then formulated as a solid, stable and palatable preparation using a ketogenic base and a combination of four commercially available formulation agents: hydrophilic fumed silica, hydrophobic fumed silica, microcrystalline cellulose, and talc. Diet compliance and safety was tested on C57Bl/6 mice over a 15-week period, comparing overall status and body weight change. Practical applications: This work provides a complete description of (i) an efficient and cost-effective synthesis of triheptanoin and (ii) its formulation as a solid, stable, and palatable ketogenic diet (triheptanoin-rich; 39% of the caloric intake) for rodents. Triheptanoin-rich diets will be helpful on pre-clinical experiments testing the therapeutic efficacy of triheptanoin in different rodent models of human diseases. In addition, using the same solidification procedure, other oils could be incorporated into rodent ketogenic diet to study their dosage and long-term effects on mammal health and development. This approach could be extremely valuable as ketogenic diet is widely used clinically for epilepsy treatment.

Large Magnetoresistance in Fe/MgO/FeCo(001) Epitaxial Tunnel-Junctions on GaAs(001).

We present tunneling experiments on Fe~001!/MgO~20 Å!/FeCo~001! single-crystal epitaxial junctions of high quality grown by sputtering and laser ablation. Tunnel magnetoresistance measurements give 60% at 30 K, to be compared with 13% obtained recently on ~001!-oriented Fe/amorphous-Al2O3 /FeCo tunnel junctions. This difference demonstrates that the spin polarization of tunneling electrons is not directly related to the density of states of the free metal surface Fe~001! in this case but depends on the actual electronic structure of the entire electrode/barrier system.