Thermal modeling and management in ultrathin chip stack technology

This paper presents a thermal modeling for power management of a new three-dimensional (3-D) thinned dies stacking process. Besides the high concentration of power dissipating sources, which is the direct consequence of the very interesting integration efficiency increase, this new ultra-compact packaging technology can suffer of the poor thermal conductivity (about 700 times smaller than silicon one) of the benzocyclobutene (BCB) used as both adhesive and planarization layers in each level of the stack. Thermal simulation was conducted using three-dimensional (3-D) FEM tool to analyze the specific behaviors in such stacked structure and to optimize the design rules. This study first describes the heat transfer limitation through the vertical path by examining particularly the case of the high dissipating sources under small area. First results of characterization in transient regime by means of dedicated test device mounted in single level structure are presented. For the design optimization, the thermal draining capabilities of a copper grid or full copper plate embedded in the intermediate layer of stacked structure are evaluated as a function of the technological parameters and the physical properties. It is shown an interest for the transverse heat extraction under the buffer devices dissipating most the power and generally localized in the peripheral zone, and for the temperature uniformization, by heat spreading mechanism, in the localized regions where the attachment of the thin die is altered. Finally, all conclusions of this analysis are used for the quantitative projections of the thermal performance of a first demonstrator based on a three-levels stacking structure for space application.

Low noise pixel detectors based on gated geiger mode avalanche photodiodes

The gated operation is proposed as an effective method to reduce the noise in pixel detectors based on Geiger mode avalanche photodiodes. A prototype with the sensor and the front-end electronics monolithically integrated has been fabricated with a conventional HV-CMOS process. Experimental results demonstrate the increase of the dynamic range of the sensor by applying this technique.

Networks of people in specialty production: family firms in the iron and steel Wire industries in Spain (1870-2000)

Capital intensive industries in specialized niches of production have constituted solid ground for family firms in Spain , as evidenced by the experience of the iron and steel wire industries between 1870 and 2000. The embeddedness of these firms in their local and regional environments have allowed the creation of networks that, together with favourable institutional conditions, significantly explain the dominance of family entrepreneurship in iron and steel wire manufacturing in Spain, until the end of the 20 th century. Dominance of family firms at the regional level has not been not an obstacle for innovation in wire manufacturing in Spain, which has taken place even when institutional conditions blocked innovation and traditional networking. Therefore, economic theories about the difficulties dynastic family firms may have to perform appropriately in science-based industries must be questioned

Networks of people in specialty production: family firms in the iron and steel Wire industries in Spain (1870-2000)

Capital intensive industries in specialized niches of production have constituted solid ground for family firms in Spain , as evidenced by the experience of the iron and steel wire industries between 1870 and 2000. The embeddedness of these firms in their local and regional environments have allowed the creation of networks that, together with favourable institutional conditions, significantly explain the dominance of family entrepreneurship in iron and steel wire manufacturing in Spain, until the end of the 20 th century. Dominance of family firms at the regional level has not been not an obstacle for innovation in wire manufacturing in Spain, which has taken place even when institutional conditions blocked innovation and traditional networking. Therefore, economic theories about the difficulties dynastic family firms may have to perform appropriately in science-based industries must be questioned

The Impact of Cooperation on R&D, Innovation andProductivity: an Analysis of Spanish Manufacturing and Services Firms

This paper investigates relationships between cooperation, R&D, innovation and productivity in Spanish firms. It uses a large sample of firm-level micro-data and applies an extended structural model that aims to explain the effects of cooperation on R&D investment, of R&D investment on output innovation, and of innovation on firms’ productivity levels. It also analyses the determinants of R&D cooperation. Firms’ technology level is taken into account in order to analyse the differences between high-tech and low-tech firms, both in the industrial and service sectors. The database used was the Technological Innovation Panel (PITEC) for the period 2004-2010. Empirical results show that firms which cooperate in innovative activities are more likely to invest in R&D in subsequent years. As expected, R&D investment has a positive impact on the probability of generating an innovation, in terms of both product and process, for manufacturing firms. Finally, innovation output has a positive impact on firms’ productivity, being greater in process innovations.

The Impact of Cooperation on R&D, Innovation and Productivity: an Analysis of Spanish Manufacturing and Services Firms

This paper investigates relationships between cooperation, R&D, innovation and productivity in Spanish firms. It uses a large sample of firm-level micro-data and applies an extended structural model that aims to explain the effects of cooperation on R&D investment, of R&D investment on output innovation, and of innovation on firms’ productivity levels. It also analyses the determinants of R&D cooperation. Firms’ technology level is taken into account in order to analyse the differences between high-tech and low-tech firms, both in the industrial and service sectors. The database used was the Technological Innovation Panel (PITEC) for the period 2004-2010. Empirical results show that firms which cooperate in innovative activities are more likely to invest in R&D in subsequent years. As expected, R&D investment has a positive impact on the probability of generating an innovation, in terms of both product and process, for manufacturing firms. Finally, innovation output has a positive impact on firms’ productivity, being greater in process innovations. Keywords: innovation sources; productivity; R&D Cooperation

Consumer acceptance of high pressure processed beef-based chilled ready meals: The mediating role of food-related lifestyle factors

The aim of this research was to investigate the effects of high pressure processing (HPP) on consumer acceptance for chilled ready meals manufactured using a low-value beef cut. Three hundred consumers evaluated chilled ready meals subjected to 4 pressure treatments and a non-treated control monadically on a 9-point scale for liking for beef tenderness and juiciness, overall flavour, overall liking, and purchase intent. Data were also collected on consumers' food consumption patterns, their attitudes towards food by means of the reduced food-related lifestyle (FRL) instrument, and socio-demographics. The results indicated that a pressure treatment of 200 MPa was acceptable to most consumers. K-means cluster analysis identified 4 consumer groups with similar preferences, and the optimal pressure treatments acceptable to specific consumer groups were identified for those firms that would wish to target attitudinally differentiated consumer segments

Young innovative firms and R&D strategies: is the Spanish case different?

This paper analyzes the profile of Spanish young innovative companies (YICs) and the determinants of innovation and imitation strategies. The results for an extensive sample of 2,221 Spanish firms studied during the period 2004–2010 show that YICs are found in all sectors, although they are more concentrated in high-tech sectors and, in particular, in knowledge-intensive services (KIS). Three of every four YICs are involved in KIS. Our results highlight that financial and knowledge barriers have much impact on the capacity of young, small firms to innovate and to become YICs, whereas market barriers are not obstacles to becoming a YIC. Public funding, in particular from the European Union, makes it easier for a new firm to become a YIC. In addition, YICs are more likely to innovate than mature firms, although they are more susceptible to sectoral and territorial factors. YICs make more dynamic use of innovation and imitation strategies when they operate in high-tech industries and are based in science parks located close to universities. Keywords: innovation strategies, public innovation policies, barriers to innovation, multinomial probit model. JEL Codes: D01, D22 , L60, L80, O31

Alzheimer disease diagnosis based on automatic spontaneous speech analysis

Alzheimer’s disease (AD) is the most prevalent form of progressive degenerative dementia and it has a high socio-economic impact in Western countries, therefore is one of the most active research areas today. Its diagnosis is sometimes made by excluding other dementias, and definitive confirmation must be done trough a post-mortem study of the brain tissue of the patient. The purpose of this paper is to contribute to im-provement of early diagnosis of AD and its degree of severity, from an automatic analysis performed by non-invasive intelligent methods. The methods selected in this case are Automatic Spontaneous Speech Analysis (ASSA) and Emotional Temperature (ET), that have the great advantage of being non invasive, low cost and without any side effects.

EEG signal analysis via a cleaning procedure based on multivariate empirical mode decomposition

Artifacts are present in most of the electroencephalography (EEG) recordings, making it difficult to interpret or analyze the data. In this paper a cleaning procedure based on a multivariate extension of empirical mode decomposition is used to improve the quality of the data. This is achieved by applying the cleaning method to raw EEG data. Then, a synchrony measure is applied on the raw and the clean data in order to compare the improvement of the classification rate. Two classifiers are used, linear discriminant analysis and neural networks. For both cases, the classification rate is improved about 20%.

Technology-enhanced education for Millennials: how the Information Society is changing the way of learning

The Information Society has provided the context for the development of a new generation, known as the Millennials, who are characterized by their intensive use of technologies in everyday life. These features are changing the way of learning, prompting educational institutions to attempt to better adapt to youngneeds by incorporating technologies into education. Based on this premise, wehave reviewed the prominent reports of the integration of ICT into education atdifferent levels with the aim of evidencing how education is changing, and willchange, to meet the needs of Millennials with ICT support. The results show thatmost of the investments have simply resulted in an increase of computers andaccess to the Internet, with teachers reproducing traditional approaches to education and e-learning being seen as complementary to face-to-face education.While it would seem that the use of ICT is not revolutionizing learning, it isfacilitating the personalization, collaboration and ubiquity of learning.

Case-based learning in VTLE: An effective strategy for improving learning design

This article presents preliminary research from an instructional design perspective on the design of the case method as an integral part of pedagogy and technology. Key features and benefitsusing this teaching and learning strategy in a Virtual Teaching and Learning Environment(VTLE) are identified, taking into account the requirements of the European Higher Education Area (EHEA) for a competence-based curricula design. The implications of these findings for alearning object approach exploring the possibilities of learning personalization, reusability and interoperability trough IMS LD, are also analyzed.

ZigBee/ZigBee PRO security assessment based on compromised cryptographic keys

Sensor networks have many applications in monitoring and controlling of environmental properties such as sound, acceleration, vibration and temperature. Due to limitedresources in computation capability, memory and energy, they are vulnerable to many kinds of attacks. The ZigBee specification based on the 802.15.4 standard, defines a set of layers specifically suited to sensor networks. These layers support secure messaging using symmetric cryptographic. This paper presents two different ways for grabbing the cryptographic key in ZigBee: remote attack and physical attack. It also surveys and categorizes some additional attacks which can be performed on ZigBee networks: eavesdropping, spoofing, replay and DoS attacks at different layers. From this analysis, it is shown that some vulnerabilities still in the existing security schema in ZigBee technology.

An Interdomain PKI Model Based on Trust Lists

The penetration of PKI technology in the market is moving slowly due to interoperability concerns. Main causes are not technical but political and social since there is no trust development model that appropriately deals with multidomain PKIs. We propose a new architecture that on one hand considers that trust is not an homogeneous property but tied to a particular relation, and on the other hand, trust management must be performed through specialized entities that can evaluate its risks and threads. The model is based on trust certificate lists that allows users to hold a personalized trust view without having to get involved in technical details. The model dynamically adapts tothe context changes thanks to a new certificate extension, we have called TrustProviderLink (TPL).

XML-based information management environment for PE technologies

Printed electronics is an emerging concept in electronics manufacturing and it is in very early development stage. The technology is not stable, design kits are not developed, and flows and Computer Aided Design (CAD) tools are not fixed yet. The European project TDK4PE addresses all this issues and this PFC has been realized on this context. The goal is to develop an XML-based information system for the collection and management of information from the technology and cell libraries developed in TDK4PE. This system will ease the treatment of that information for a later generation of specific Design Kits (DK) and the corresponding documentation. This work proposes a web application to generate technology files and design kits in a formatted way; it also proposes a structure for them and a database implementation for storing the needed information. The application will allow its users to redefine the structure of those files, as well as export and import XML files, between other formats.