499 resultados para Nanocristalls -- Propietats tèrmiques
Resumo:
ZnO nanorods grown by both high temperature vapour phase transport and low temperature chemical bath deposition are very promising sources for UV third harmonic generation. Material grown by both methods show comparable efficiencies, in both cases an order of magnitude higher than surface third harmonic generation at the quartz-air interface of a bare quartz substrate. This result is in stark contrast to the linear optical properties of ZnO nanorods grown by these two methods, which show vastly different PL efficiencies. The third harmonic generated signal is analysed using intensity dependent measurements and interferometric frequency resolved optical gating, allowing extraction of the laser pulse parameters. The comparable levels of efficiency of ZnO grown by these very different methods as sources for third harmonic UV generation provides a broad suite of possible growth methods to suit various substrates, coverage and scalability requirements. Potential application areas range from interferometric frequency resolved optical gating characterization of few cycle fs pulses to single cell UV irradiation for biophysical studies.
Resumo:
Es posible obtener cementos de fosfato de magnesio y potasio (KMgPO4·6H2O; K-estruvita), mediante la reacción en medio acuoso del óxido de magnesio y el dihidrogenofosfato de potasio, siendo ésta una reacción exotérmica muy rápida que permite el fraguado del material en pocos minutos. Estos cementos, formulados a partir de óxidos de magnesio de elevada pureza y coste elevado, se encuentran descritos en la bibliografía para su utilización en el encapsulamiento de residuos especiales y como morteros de cemento para la reparación de hormigón. Sin embargo cabe la posibilidad de poder formular este mismo tipo de cementos con óxidos de magnesio de bajo contenido, cuyo precio es del orden de 10 a 15 veces más barato que el óxido de magnesio de elevada pureza. En el presente estudio se evalúa la utilización de óxidos de magnesio de bajo contenido (¿70% MgO), obtenidos en el proceso de calcinación de la magnesita natural, para la formulación de cementos de K-estruvita. En este estudio se pretende determinar la formulación óptima de estos cementos a partir de la evaluación tanto de las propiedades mecánicas como de los tiempos de fraguado de las diferentes composiciones.
Resumo:
En este trabajo se estudia la influencia de la atmósfera de sinterización sobre la estabilidad térmica de cerámicas de hidroxiapatita (HA) reforzadas con partículas de circona parcialmente estabilizada con magnesia (Mg-PSZ). Los cuerpos verdes fueron obtenidos por prensado uniaxial y las sinterizaciones se realizaron en aire y en oxígeno húmedo. El estudio por difracción de rayos-X y espectroscopía infrarroja permitió comprobar que la atmósfera húmeda evita la descomposición de la hidroxiapatita, todo lo contrario a lo que sucede en aire donde es evidente la presencia del zirconato cálcico (CZ) en la interfaz entre la partícula de circona y la matriz de HA. La caracterización microestructural de los materiales por Microscopía Electrónica de Barrido permitió apreciar el desarrollo de tamaño de grano de los materiales sinterizados. El estudio del comportamiento mecánico mediante ensayos de indentación reveló un aumento de la tenacidad a la fractura en el caso de los materiales que presentaban Mg-PSZ con respecto a la HA pura.
Resumo:
[cat] Utilitzem un conjunt de mètriques del paisatge per estudiar l'evolució a llarg termini seguida en una típica zona costanera del Mediterrani des de 1850 fins a 2005, que mostren una greu deterioració del medi ambient entre 1950 i 2005. Les principals forces motores d'aquesta degradació del paisatge han estat el creixement urbà experimentat a les antigues zones agrícoles situades a les planes litorals, juntament amb l'abandonament i la reforestació dels vessants dels pujols interceptats per àrees residencials de baixa densitat, carreteres i altres infraestructures lineals. Duem a terme una anàlisi estadística de redundància (RDA) amb la finalitat d'identificar els que considerem com alguns agents rectors socioeconòmics i polítics d'última instància d'aquests impactes ambientals. Els resultats confirmen les nostres hipòtesis interpretatives, que són que: 1) els canvis en les cobertes i usos del sòl determinen canvis en les propietats dels paisatge, tant estructurals com funcionals; 2) aquests canvis no es produeixen per atzar, sinó que estan relacionats amb factors geogràfics i forces socioeconòmiques i polítiques.
Resumo:
[cat] Utilitzem un conjunt de mètriques del paisatge per estudiar l'evolució a llarg termini seguida en una típica zona costanera del Mediterrani des de 1850 fins a 2005, que mostren una greu deterioració del medi ambient entre 1950 i 2005. Les principals forces motores d'aquesta degradació del paisatge han estat el creixement urbà experimentat a les antigues zones agrícoles situades a les planes litorals, juntament amb l'abandonament i la reforestació dels vessants dels pujols interceptats per àrees residencials de baixa densitat, carreteres i altres infraestructures lineals. Duem a terme una anàlisi estadística de redundància (RDA) amb la finalitat d'identificar els que considerem com alguns agents rectors socioeconòmics i polítics d'última instància d'aquests impactes ambientals. Els resultats confirmen les nostres hipòtesis interpretatives, que són que: 1) els canvis en les cobertes i usos del sòl determinen canvis en les propietats dels paisatge, tant estructurals com funcionals; 2) aquests canvis no es produeixen per atzar, sinó que estan relacionats amb factors geogràfics i forces socioeconòmiques i polítiques.
Resumo:
[cat] Estudiem les propietats teòriques que una funció d.emparellament ha de satisfer per tal de representar un mercat laboral amb friccions dins d'un model d'equilibri general amb emparellament aleatori. Analitzem el cas Cobb-Douglas, CES i altres formes funcionals per a la funció d.emparellament. Els nostres resultats estableixen restriccions sobre els paràmetres d'aquests formes funcionals per assegurar que l.equilibri és interior. Aquestes restriccions aporten raons teòriques per escollir entre diverses formes funcionals i permeten dissenyar tests d'error d'especificació de model en els treballs empírics.
Resumo:
The possible use of polyethylene naphthalate as substrate for low-temperature deposited solar cells has been studied in this paper. The transparency of this polymer makes it a candidate to be used in both substrate and superstrate configurations. ZnO:Al has been deposited at room temperature on top of PEN. The resulting structure PEN/ZnO:Al presented good optical and electrical properties. PEN has been successfully textured (nanometer and micrometer random roughness) using hot-embossing lithography. Reflector structures have been built depositing Ag and ZnO:Al on top of the stamped polymer. The deposition of these layers did not affect the final roughness of the whole. The reflector structure has been morphologically and optically analysed to verify its suitability to be used in solar cells.
Resumo:
In a previous paper [Hidalgo et al., Phys. Rev. Lett. 103, 118001 (2009)] it was shown that square particles deposited in a silo tend to align with a diagonal parallel to the gravity, giving rise to a deposit with very particular properties. Here we explore, both experimentally and numerically, the effect on these properties of the filling mechanism. In particular, we modify the volume fraction of the initial configuration from which the grains are deposited. Starting from a very dilute case, increasing the volume fraction results in an enhancement of the disorder in the final deposit characterized by a decrease of the final packing fraction and a reduction of the number of particles oriented with their diagonal in the direction of gravity. However, for very high initial volume fractions, the final packing fraction increases again. This result implies that two deposits with the same final packing fraction can be obtained from very different initial conditions. The structural properties of such deposits are analyzed, revealing that, although the final volume fraction is the same, their micromechanical properties notably differ.
Resumo:
[cat] Estudiem les propietats teòriques que una funció d.emparellament ha de satisfer per tal de representar un mercat laboral amb friccions dins d'un model d'equilibri general amb emparellament aleatori. Analitzem el cas Cobb-Douglas, CES i altres formes funcionals per a la funció d.emparellament. Els nostres resultats estableixen restriccions sobre els paràmetres d'aquests formes funcionals per assegurar que l.equilibri és interior. Aquestes restriccions aporten raons teòriques per escollir entre diverses formes funcionals i permeten dissenyar tests d'error d'especificació de model en els treballs empírics.
Resumo:
El projecte TECNOLONIAL té com a principal objectiu aprofundir en aspectes relacionats amb la interacció, influència i aculturació durant el procés de colonització a Amèrica. En aquest sentit, cal destacar que s"utilitza el terme"aculturació" com a nom genèric per denominar un procés complex de contactes entre societats diferents i diverses; procés que donarà com a resultat diverses respostes a la integració i/o resistència d"acord amb diferents situacions i estratègies, com el desenvolupament de noves identitats en les àrees colonitzades on grups humans mixtos i complexos es troben ubicats. El projecte se centra en l"expansió atlàntica espanyola, especialment durant el segle XVI, com a punt de partida del comerç global que es practica avui dia entre societats completament interconnectades.La investigació es basa essencialment en l"estudi de la ceràmica (majòlica, vidriada i contenidors de transport, com també ceràmiques indígenes), que és un bé o un bé comercial de valor intrínsec, d"ús intensiu i relacionat amb activitats quotidianes i simbòliques. A més, la seva ubiqüitat i abundància en el registre arqueològic converteixen la ceràmica en l"objecte ideal per contestar aquest tipus de qüestions. En aquest sentit, la caracterització de la tecnologia ceràmica, que inclou les seves decoracions i vidriats les propietats mecàniques, com també l"avaluació dels seus dissenys formals, ens ha de permetre aconseguir un profund coneixement de la tecnologia europea i del seu impacte transformador sobre la producció ceràmica indígena
Resumo:
A statistical indentation method has been employed to study the hardness value of fire-refined high conductivity copper, using nanoindentation technique. The Joslin and Oliver approach was used with the aim to separate the hardness (H) influence of copper matrix, from that of inclusions and grain boundaries. This approach relies on a large array of imprints (around 400 indentations), performed at 150 nm of indentation depth. A statistical study using a cumulative distribution function fit and Gaussian simulated distributions, exhibits that H for each phase can be extracted when the indentation depth is much lower than the size of the secondary phases. It is found that the thermal treatment produces a hardness increase, due to the partly re-dissolution of the inclusions (mainly Pb and Sn) in the matrix.
Resumo:
In this article, we explore the possibility of modifying the silicon nanocrystal areal density in SiOx single layers, while keeping constant their size. For this purpose, a set of SiOx monolayers with controlled thickness between two thick SiO2 layers has been fabricated, for four different compositions (x=1, 1.25, 1.5, or 1.75). The structural properties of the SiO x single layers have been analyzed by transmission electron microscopy (TEM) in planar view geometry. Energy-filtered TEM images revealed an almost constant Si-cluster size and a slight increase in the cluster areal density as the silicon content increases in the layers, while high resolution TEM images show that the size of the Si crystalline precipitates largely decreases as the SiO x stoichiometry approaches that of SiO2. The crystalline fraction was evaluated by combining the results from both techniques, finding a crystallinity reduction from 75% to 40%, for x = 1 and 1.75, respectively. Complementary photoluminescence measurements corroborate the precipitation of Si-nanocrystals with excellent emission properties for layers with the largest amount of excess silicon. The integrated emission from the nanoaggregates perfectly scales with their crystalline state, with no detectable emission for crystalline fractions below 40%. The combination of the structural and luminescence observations suggests that small Si precipitates are submitted to a higher compressive local stress applied by the SiO2 matrix that could inhibit the phase separation and, in turn, promotes the creation of nonradiative paths.
Resumo:
Hydrogenated nanocrystalline silicon thin-films were obtained by catalytic chemical vapour deposition at low substrate temperatures (150°C) and high deposition rates (10 Å/s). These films, with crystalline fractions over 90%, were incorporated as the active layers of bottom-gate thin-film transistors. The initial field-effect mobilities of these devices were over 0.5 cm 2/V s and the threshold voltages lower than 4 V. In this work, we report on the enhanced stability of these devices under prolonged times of gate bias stress compared to amorphous silicon thin-film transistors. Hence, they are promising candidates to be considered in the future for applications such as flat-panel displays.
Resumo:
The very usual columnar growth of nanocrystalline silicon leads to electronic transport anisotropies. Whereas electrical measurements with coplanar electrodes only provide information about the electronic transport parallel to the substrate, it is the transverse transport which determines the collection efficiency in thin film solar cells. Hence, Schottky diodes on transparent electrodes were obtained by hot-wire CVD in order to perform external quantum efficiency and surface photovoltage studies in sandwich configuration. These measurements allowed to calculate a transverse collection length, which must correlate with the photovoltaic performance of thin film solar cells. Furthermore, the density of charge trapped at localized states in the bandgap was estimated from the voltage dependence of the depletion capacitance of these rectifying contacts.
Resumo:
The charge ordered La1/3Sr2/3FeO3−δ (LSFO) in bulk and nanocrystalline forms are investigated using ac and dc magnetization, M¨ossbauer, and polarized neutron studies. A complex scenario of short-range charge and magnetic ordering is realized from the polarized neutron studies in nanocrystalline specimen. This short-range ordering does not involve any change in spin state and modification in the charge disproportion between Fe3+ and Fe5+ compared to bulk counterpart as evident in the M¨ossbauer results. The refinement of magnetic diffraction peaks provides magnetic moments of Fe3+ and Fe5+ are about 3.15 μB and 1.57 μB for bulk, and 2.7 μB and 0.53 μB for nanocrystalline specimen, respectively. The destabilization of charge ordering leads to magnetic phase separation, giving rise to the robust exchange bias (EB) effect. Strikingly, EB field at 5 K attains a value as high as 4.4 kOe for average size ∼70 nm, which is zero for the bulk counterpart. A strong frequency dependence of ac susceptibility reveals cluster-glass-like transition around ∼65 K, below which EB appears. Overall results propose that finite-size effect directs the complex glassy magnetic behavior driven by unconventional short-range charge and magnetic ordering, and magnetic phase separation appears in nanocrystalline LSFO.