Amorphous silicon thin film solar cells deposited entirely by Hot-Wire Chemical Vapour Deposition at low temperature (<150 ºC)

Amorphous silicon n-i-p solar cells have been fabricated entirely by Hot-Wire Chemical Vapour Deposition (HW-CVD) at low process temperature < 150 °C. A textured-Ag/ZnO back reflector deposited on Corning 1737F by rf magnetron sputtering was used as the substrate. Doped layers with very good conductivity and a very less defective intrinsic a-Si:H layer were used for the cell fabrication. A double n-layer (μc-Si:H/a-Si:H) and μc-Si:H p-layer were used for the cell. In this paper, we report the characterization of these layers and the integration of these layers in a solar cell fabricated at low temperature. An initial efficiency of 4.62% has been achieved for the n-i-p cell deposited at temperatures below 150 °C over glass/Ag/ZnO textured back reflector.

Electronic transport in low temperature nanocrystalline silicon thin-film transistors obtained by Hot-Wire CVD

Hydrogenated nanocrystalline silicon (nc-Si:H) obtained by hot-wire chemical vapour deposition (HWCVD) at low substrate temperature (150 °C) has been incorporated as the active layer in bottom-gate thin-film transistors (TFTs). These devices were electrically characterised by measuring in vacuum the output and transfer characteristics for different temperatures. The field-effect mobility showed a thermally activated behaviour which could be attributed to carrier trapping at the band tails, as in hydrogenated amorphous silicon (a-Si:H), and potential barriers for the electronic transport. Trapped charge at the interfaces of the columns, which are typical in nc-Si:H, would account for these barriers. By using the Levinson technique, the quality of the material at the column boundaries could be studied. Finally, these results were interpreted according to the particular microstructure of nc-Si:H.

Microcrystalline silicon thin film transistors obtained by Hot-Wire CVD

Polysilicon thin film transistors (TFT) are of great interest in the field of large area microelectronics, especially because of their application as active elements in flat panel displays. Different deposition techniques are in tough competition with the objective to obtain device-quality polysilicon thin films at low temperature. In this paper we present the preliminary results obtained with the fabrication of TFT deposited by hot-wire chemical vapor deposition (HWCVD). Some results concerned with the structural characterization of the material and electrical performance of the device are presented.

Thin Film Transistors obtained by Hot-Wire CVD

Hydrogenated microcrystalline silicon films obtained at low temperature (150-280°C) by hot wire chemical vapour deposition at two different process pressures were measured by Raman spectroscopy, X-ray diffraction (XRD) spectroscopy and photothermal deflection spectroscopy (PDS). A crystalline fraction >90% with a subgap optical absortion 10 cm -1 at 0.8 eV were obtained in films deposited at growth rates >0.8 nm/s. These films were incorporated in n-channel thin film transistors and their electrical properties were measured. The saturation mobility was 0.72 ± 0.05 cm 2/ V s and the threshold voltage around 0.2 eV. The dependence of their conductance activation energies on gate voltages were related to the properties of the material.

Microdoping compensation of microcrystalline silicon obtained by Hot-Wire Chemical Vapour Deposition

Undoped hydrogenated microcrystalline silicon was obtained by hot-wire chemical vapour deposition at different silane-to-hydrogen ratios and low temperature (<300 °C). As well as technological aspects of the deposition process, we report structural, optical and electrical characterizations of the samples that were used as the active layer for preliminary p-i-n solar cells. Raman spectroscopy indicates that changing the hydrogen dilution can vary the crystalline fraction. From electrical measurements an unwanted n-type character is deduced for this undoped material. This effect could be due to a contaminant, probably oxygen, which is also observed in capacitance-voltage measurements on Schottky structures. The negative effect of contaminants on the device was dramatic and a compensated p-i-n structure was also deposited to enhance the cell performance.

Electronic properties of a quantum wire with arbitrary bending angle

The electron transmission and bound state properties of a quantum wire with a sharp bend at arbitrary angle are studied, extending results on the right angle sharp bend (the L¿shaped wire). These new results are compared to those of a similar structure, the circular bend wire. The possibility of using a bent wire to perform transistor action is also discussed.

Implementation of IPM programs on European greenhouse tomato production areas: Tools and constraints

Whiteflies and whitefly-transmitted viruses are some of the major constraints on European tomato production. The main objectives of this study were to: identify where and why whiteflies are a major limitation on tomato crops; collect information about whiteflies and associated viruses; determine the available management tools; and identify key knowledge gaps and research priorities. This study was conducted within the framework of ENDURE (European Network for Durable Exploitation of Crop Protection Strategies). Two whitefly species are the main pests of tomato in Europe: Bemisia tabaci and Trialeurodes vaporariorum. Trialeurodes vaporariorum is widespread to all areas where greenhouse industry is present, and B. tabaci has invaded, since the early 1990’s, all the subtropical and tropical areas. Biotypes B and Q of B. tabaci are widespread and especially problematic. Other key tomato pests are Aculops lycopersici, Helicoverpa armigera, Frankliniella occidentalis, and leaf miners. Tomato crops are particularly susceptible to viruses causingTomato yellow leaf curl disease (TYLCD). High incidences of this disease are associated to high pressure of its vector, B. tabaci. The ranked importance of B. tabaci established in this study correlates with the levels of insecticide use, showing B. tabaci as one of the principal drivers behind chemical control. Confirmed cases of resistance to almost all insecticides have been reported. Integrated Pest Management based on biological control (IPM-BC) is applied in all the surveyed regions and identified as the strategy using fewer insecticides. Other IPM components include greenhouse netting and TYLCD-tolerant tomato cultivars. Sampling techniques differ between regions, where decisions are generally based upon whitefly densities and do not relate to control strategies or growing cycles. For population monitoring and control, whitefly species are always identified. In Europe IPM-BC is the recommended strategy for a sustainable tomato production. The IPM-BC approach is mainly based on inoculative releases of the parasitoids Eretmocerus mundus and Encarsia formosa and/or the polyphagous predators Macrolophus caliginosus and Nesidiocoris tenuis. However, some limitations for a wider implementation have been identified: lack of biological solutions for some pests, costs of beneficials, low farmer confidence, costs of technical advice, and low pest injury thresholds. Research priorities to promote and improve IPM-BC are proposed on the following domains: (i) emergence and invasion of new whitefly-transmitted viruses; (ii) relevance of B. tabaci biotypes regarding insecticide resistance; (iii) biochemistry and genetics of plant resistance; (iv) economic thresholds and sampling techniques of whiteflies for decision making; and (v) conservation and management of native whitefly natural enemies and improvement of biological control of other tomato pests.

Disseny, modelat i fabricació d'una antena "trap" per aplicacions WLAN

En aquest treball s’ha dissenyat i fabricat una antena monopol en estructura planar capaç de treballar correctament a les freqüències WLAN de 2,45-2,5 GHz (802.11b/g) i 4,9-5,875 GHz (802.11a/h/j). Per arribar a aquest objectiu primer s’ha presentat el model de línia de transmissió acabada en circuit obert per simular el comportament d’una antena. S’han comparat i verificat els resultats amb el model d’antena de fil. Seguidament, s’ha estudiat el comportament que introdueix el fet de carregar l’antena amb un ressonador LC. Finalment, s’ha passat del model d’antena de fil a una estructura planar. Aquesta geometria ha permès la realització del trap LC de forma distribuïda a través d’un ressonador CLL. El principi de disseny de l’antena està basat en la introducció d’aquest ressonador CLL amb freqüència de ressonància situada entre les dos bandes de treball i que junt amb l’ajust dels diversos paràmetres que defineixen l’antena han permès obtenir més 1 GHz d’ample de banda a la freqüència de 5 GHz.

La construcción del espacio dramático en la ficción televisiva norteamericana. Análisis del espacio vivencial en las series dramáticas de la HBO

El presente trabajo analiza la construcción del espacio vivencial en cinco series televisivas producidas por la cadena norteamericana HBO: Carnivàle, Deadwood, The Sopranos, The Wire y Treme. La investigación parte de la convicción de una posible reelaboración de la historia del espacio doméstico norteamericano a través de la puesta en escena y de la potencialidad simbólica del espacio serial. De este modo, el trabajo propone un recorrido hermenéutico en el que se analiza la evolución del espacio narrativo, su evolución morfológica en dependencia de las necesidades diegéticas de cada una de las obras analizadas.

Contagion and efficiency in gross and net interbank payment systems

The increased fragility of the banking industry has generatedgrowing concern about the risks associated with the paymentsystems. Although in most industrial countries differentinterbank payment systems coexist, little is really knownabout their propierties in terms of risk and efficiency. Wetackle this question by comparing the two main types ofpayment systems, gross and net, in a framework whereuncertainty arises from several sources: the time ofconsumption, the location of consumption and the return oninvestment. Payments across locations can be made either bydirectly transferrring liquidity or by transferring claimsagainst the bank in the other location. The two mechanism areinterpreted as the gross and net settlement systems ininterbank payments. We characterize the equilibria in the twosystems and identify the trade-off in terms of safety andefficiency.

Effective one-dimensional square well for two-dimensional quantum wires

The symmetrical two-dimensional quantum wire with two straight leads joined to an arbitrarily shaped interior cavity is studied with emphasis on the single-mode approximation. It is found that for both transmission and bound-state problems the solution is equivalent to that for an energy-dependent one-dimensional square well. Quantum wires with a circular bend, and with single and double right-angle bends, are examined as examples. We also indicate a possible way to detect bound states in a double bend based on the experimental setup of Wu et al.

Exchange-correlation effects on quantum wires with spin-orbit interactions under the influence of in-plane magnetic fields.

Within the noncollinear local spin-density approximation, we have studied the ground state structure of a parabolically confined quantum wire submitted to an in-plane magnetic field, including both Rashba and Dresselhaus spin-orbit interactions. We have explored a wide range of linear electronic densities in the weak (strong) coupling regimes that appear when the ratio of spin-orbit to confining energy is small (large). These results are used to obtain the conductance of the wire. In the strong coupling limit, the interplay between the applied magnetic field¿irrespective of the in-plane direction, the exchange-correlation energy, and the spin-orbit energy-produces anomalous plateaus in the conductance vs linear density plots that are otherwise absent, or washes out plateaus that appear when the exchange-correlation energy is not taken into account.

Understanding quantum wires with circular bends

It is shown that propagation around a circular bend in a quantum wire is well approximated by a one¿dimensional problem with a square¿well potential replacing the bend. Simple analytic expressions are obtained for the transmission and bound states.

Real-time monitoring of the silicidation process of tungsten filaments at high temperature used as catalysers for silane decomposition

The scope of this work is the systematic study of the silicidation process affecting tungsten filaments at high temperature (1900ºC) used for silane decomposition in the hot-wire chemical vapour deposition technique (HWCVD). The correlation between the electrical resistance evolution of the filaments, Rfil(t), and the different stages of the their silicidation process is exposed. Said stages correspond to: the rapid formation of two WSi2 fronts at the cold ends of the filaments and their further propagation towards the middle of the filaments; and, regarding the hot central portion of the filaments: a initial stage of silicon dissolution into the tungsten bulk, with a random duration for as-manufactured filaments, followed by the inhomogeneous nucleation of W5Si3 (which is later replaced by WSi2) and its further growth towards the filaments core. An electrical model is used to obtain real-time information about the current status of the filaments silicidation process by simply monitoring their Rfil(t) evolution during the HWCVD process. It is shown that implementing an annealing pre-treatment to the filaments leads to a clearly repetitive trend in the monitored Rfil(t) signatures. The influence of hydrogen dilution of silane on the filaments silicidation process is also discussed.

Large gypsum nodules in the Paleogene and Neogene evaporites of Spain: distribution and palaeogeographic significance

Sabkha and deep burial set tings are the most com mon sites where diagenetic anhydrite forms. In a sabkha setting, displacive facies (iso lated nodules, bed ded nodules, enterolithic levels) of early diagenetic or primary anhydrite are generated (Shearman, 1966; Hardie, 1967). These anhydrite facies are commonly foundat the top of shoal ing cycles representing the evolution from subaqueous depositional conditions at the base (carbonates, lutites) to exposure conditions at the top where in ter stitially-grown gypsum/anhydrite de velops ( sabkha cy cles). In a deep burial setting, gypsum transforms to tally to anhydrite with in creas ing temperature and lithostatic pressure (Murray, 1964). Al though this mineral transformation usually preserves the depositional gypsum facies, a significant textural change is in volved in other cases, resulting in replacive anhydrite with a nodular-mosaic or"chicken-wire" fabric (Warren, 2006). In the two settings, how ever, the size of the individual anhydrite nodules is relatively small, rarely reaching some tens of centimetres across. More over, bedding is preserved or little disturbed, al though minor de formation is caused by the displacive sabkha nodules.