Simulation of Delamination Propagation in Composites Under High-Cycle Fatigue by Means of Cohesive-Zone Models

A damage model for the simulation of delamination propagation under high-cycle fatigue loading is proposed. The basis for the formulation is a cohesive law that links fracture and damage mechanics to establish the evolution of the damage variable in terms of the crack growth rate dA/dN. The damage state is obtained as a function of the loading conditions as well as the experimentally-determined coefficients of the Paris Law crack propagation rates for the material. It is shown that by using the constitutive fatigue damage model in a structural analysis, experimental results can be reproduced without the need of additional model-specific curve-fitting parameters

Inference of distributional parameters from compositional samples containing nondetects

Low concentrations of elements in geochemical analyses have the peculiarity of beingcompositional data and, for a given level of significance, are likely to be beyond thecapabilities of laboratories to distinguish between minute concentrations and completeabsence, thus preventing laboratories from reporting extremely low concentrations of theanalyte. Instead, what is reported is the detection limit, which is the minimumconcentration that conclusively differentiates between presence and absence of theelement. A spatially distributed exhaustive sample is employed in this study to generateunbiased sub-samples, which are further censored to observe the effect that differentdetection limits and sample sizes have on the inference of population distributionsstarting from geochemical analyses having specimens below detection limit (nondetects).The isometric logratio transformation is used to convert the compositional data in thesimplex to samples in real space, thus allowing the practitioner to properly borrow fromthe large source of statistical techniques valid only in real space. The bootstrap method isused to numerically investigate the reliability of inferring several distributionalparameters employing different forms of imputation for the censored data. The casestudy illustrates that, in general, best results are obtained when imputations are madeusing the distribution best fitting the readings above detection limit and exposes theproblems of other more widely used practices. When the sample is spatially correlated, itis necessary to combine the bootstrap with stochastic simulation

A critical analysis of dimensions and curve fitting practice in economics

When dealing with sustainability we are concerned with the biophysical as well as the monetary aspects of economic and ecological interactions. This multidimensional approach requires that special attention is given to dimensional issues in relation to curve fitting practice in economics. Unfortunately, many empirical and theoretical studies in economics, as well as in ecological economics, apply dimensional numbers in exponential or logarithmic functions. We show that it is an analytical error to put a dimensional unit x into exponential functions ( a x ) and logarithmic functions ( x a log ). Secondly, we investigate the conditions of data sets under which a particular logarithmic specification is superior to the usual regression specification. This analysis shows that logarithmic specification superiority in terms of least square norm is heavily dependent on the available data set. The last section deals with economists’ “curve fitting fetishism”. We propose that a distinction be made between curve fitting over past observations and the development of a theoretical or empirical law capable of maintaining its fitting power for any future observations. Finally we conclude this paper with several epistemological issues in relation to dimensions and curve fitting practice in economics

Reconsideration of dimensions and curve fitting practice in economics ellaborating on Georgescu-Roegen’s economic methodology

This paper is to examine the proper use of dimensions and curve fitting practices elaborating on Georgescu-Roegen’s economic methodology in relation to the three main concerns of his epistemological orientation. Section 2 introduces two critical issues in relation to dimensions and curve fitting practices in economics in view of Georgescu-Roegen’s economic methodology. Section 3 deals with the logarithmic function (ln z) and shows that z must be a dimensionless pure number, otherwise it is nonsensical. Several unfortunate examples of this analytical error are presented including macroeconomic data analysis conducted by a representative figure in this field. Section 4 deals with the standard Cobb-Douglas function. It is shown that the operational meaning cannot be obtained for capital or labor within the Cobb-Douglas function. Section 4 also deals with economists "curve fitting fetishism". Section 5 concludes thispaper with several epistemological issues in relation to dimensions and curve fitting practices in economics.

A Factor analysis of hidrochemical composition of Llobregat river basin

Hydrogeological research usually includes some statistical studies devised to elucidate mean background state, characterise relationships among different hydrochemical parameters, and show the influence of human activities. These goals are achieved either by means of a statistical approach or by mixing modelsbetween end-members. Compositional data analysis has proved to be effective with the first approach, but there is no commonly accepted solution to the end-member problem in a compositional framework.We present here a possible solution based on factor analysis of compositions illustrated with a case study.We find two factors on the compositional bi-plot fitting two non-centered orthogonal axes to the most representative variables. Each one of these axes defines a subcomposition, grouping those variables thatlay nearest to it. With each subcomposition a log-contrast is computed and rewritten as an equilibrium equation. These two factors can be interpreted as the isometric log-ratio coordinates (ilr) of three hiddencomponents, that can be plotted in a ternary diagram. These hidden components might be interpreted as end-members.We have analysed 14 molarities in 31 sampling stations all along the Llobregat River and its tributaries, with a monthly measure during two years. We have obtained a bi-plot with a 57% of explained totalvariance, from which we have extracted two factors: factor G, reflecting geological background enhanced by potash mining; and factor A, essentially controlled by urban and/or farming wastewater. Graphicalrepresentation of these two factors allows us to identify three extreme samples, corresponding to pristine waters, potash mining influence and urban sewage influence. To confirm this, we have available analysisof diffused and widespread point sources identified in the area: springs, potash mining lixiviates, sewage, and fertilisers. Each one of these sources shows a clear link with one of the extreme samples, exceptfertilisers due to the heterogeneity of their composition.This approach is a useful tool to distinguish end-members, and characterise them, an issue generally difficult to solve. It is worth note that the end-member composition cannot be fully estimated but only characterised through log-ratio relationships among components. Moreover, the influence of each endmember in a given sample must be evaluated in relative terms of the other samples. These limitations areintrinsic to the relative nature of compositional data

Estimation of the viscoelastic properties of vessel walls using a computational model and Doppler ultrasound

Human arteries affected by atherosclerosis are characterized by altered wall viscoelastic properties. The possibility of noninvasively assessing arterial viscoelasticity in vivo would significantly contribute to the early diagnosis and prevention of this disease. This paper presents a noniterative technique to estimate the viscoelastic parameters of a vascular wall Zener model. The approach requires the simultaneous measurement of flow variations and wall displacements, which can be provided by suitable ultrasound Doppler instruments. Viscoelastic parameters are estimated by fitting the theoretical constitutive equations to the experimental measurements using an ARMA parameter approach. The accuracy and sensitivity of the proposed method are tested using reference data generated by numerical simulations of arterial pulsation in which the physiological conditions and the viscoelastic parameters of the model can be suitably varied. The estimated values quantitatively agree with the reference values, showing that the only parameter affected by changing the physiological conditions is viscosity, whose relative error was about 27% even when a poor signal-to-noise ratio is simulated. Finally, the feasibility of the method is illustrated through three measurements made at different flow regimes on a cylindrical vessel phantom, yielding a parameter mean estimation error of 25%.

Variable Kernel estimates: On the impossibility of tuning the parameters

For the standard kernel density estimate, it is known that one can tune the bandwidth such that the expected L1 error is within a constant factor of the optimal L1 error (obtained when one is allowed to choose the bandwidth with knowledge of the density). In this paper, we pose the same problem for variable bandwidth kernel estimates where the bandwidths are allowed to depend upon the location. We show in particular that for positive kernels on the real line, for any data-based bandwidth, there exists a densityfor which the ratio of expected L1 error over optimal L1 error tends to infinity. Thus, the problem of tuning the variable bandwidth in an optimal manner is ``too hard''. Moreover, from the class of counterexamples exhibited in the paper, it appears thatplacing conditions on the densities (monotonicity, convexity, smoothness) does not help.

On the performance of small-area estimators: Fixed vs. random area parameters

Most methods for small-area estimation are based on composite estimators derived from design- or model-based methods. A composite estimator is a linear combination of a direct and an indirect estimator with weights that usually depend on unknown parameters which need to be estimated. Although model-based small-area estimators are usually based on random-effects models, the assumption of fixed effects is at face value more appropriate.Model-based estimators are justified by the assumption of random (interchangeable) area effects; in practice, however, areas are not interchangeable. In the present paper we empirically assess the quality of several small-area estimators in the setting in which the area effects are treated as fixed. We consider two settings: one that draws samples from a theoretical population, and another that draws samples from an empirical population of a labor force register maintained by the National Institute of Social Security (NISS) of Catalonia. We distinguish two types of composite estimators: a) those that use weights that involve area specific estimates of bias and variance; and, b) those that use weights that involve a common variance and a common squared bias estimate for all the areas. We assess their precision and discuss alternatives to optimizing composite estimation in applications.

A finite-population revenue management model and a risk-ratio procedure for the joint estimation of population size and parameters

Many dynamic revenue management models divide the sale period into a finite number of periods T and assume, invoking a fine-enough grid of time, that each period sees at most one booking request. These Poisson-type assumptions restrict the variability of the demand in the model, but researchers and practitioners were willing to overlook this for the benefit of tractability of the models. In this paper, we criticize this model from another angle. Estimating the discrete finite-period model poses problems of indeterminacy and non-robustness: Arbitrarily fixing T leads to arbitrary control values and on the other hand estimating T from data adds an additional layer of indeterminacy. To counter this, we first propose an alternate finite-population model that avoids this problem of fixing T and allows a wider range of demand distributions, while retaining the useful marginal-value properties of the finite-period model. The finite-population model still requires jointly estimating market size and the parameters of the customer purchase model without observing no-purchases. Estimation of market-size when no-purchases are unobservable has rarely been attempted in the marketing or revenue management literature. Indeed, we point out that it is akin to the classical statistical problem of estimating the parameters of a binomial distribution with unknown population size and success probability, and hence likely to be challenging. However, when the purchase probabilities are given by a functional form such as a multinomial-logit model, we propose an estimation heuristic that exploits the specification of the functional form, the variety of the offer sets in a typical RM setting, and qualitative knowledge of arrival rates. Finally we perform simulations to show that the estimator is very promising in obtaining unbiased estimates of population size and the model parameters.

A type stars - physical parameters from UVBY and H-beta photometry

uvby H-beta photometry has been obtained for a sample of 93 selected main sequence A stars. The purpose was to determine accurate effective temperatures, surface gravities, and absolute magnitudes for an individual determination of ages and parallaxes, which have to be included in a more extensive work analyzing the kinematic properties of A V stars. Several calibrations and methods to determine the above mentioned parameters have been reviewed, allowing the design of a new algorithm for their determination. The results obtained using this procedure were tested in a previous paper using uvby H-beta data from the Hauck and Mermilliod catalogue, and comparing the rusulting temperatures, surface gravities and absolute magnitudes with empirical determinations of these parameters.

Improved multiexponential transient spectroscopy by iterative deconvolution

The analysis of multiexponential decays is challenging because of their complex nature. When analyzing these signals, not only the parameters, but also the orders of the models, have to be estimated. We present an improved spectroscopic technique specially suited for this purpose. The proposed algorithm combines an iterative linear filter with an iterative deconvolution method. A thorough analysis of the noise effect is presented. The performance is tested with synthetic and experimental data.

Measuring conduct and cost parameters in the Spanish air transport market

This paper estimates a model of airline competition for the Spanish air transport market. I test the explanatory power of alternative oligopoly models with capacity constraints. In addition, I analyse the degree of density economies. Results show that Spanish airlines conduct follows a price-leadership scheme so that it is less competitive than the Cournot solution. I also find evidence that thin routes can be considered as natural monopolies

Classical parameters of Shadowlands by Richard Attenborough (On C. S. Lewis's Life and Work)

The aim of this article is to show the classical parameters of Shadowlands by R. Attenborough, with a screenplay by W. Nicholson, on C. S. Lewis's life and work. Based upon an accurate reading of Lewis's works, the author of this article proposes to interpret the opposition Lewis / Gresham as the translation into the real life of the opposition between the Platonic or idealistic and the Aristotelian or materialistic temperaments which was already maintained by Coleridge. In any case, there are many classical references which must be taken into account in order to understand to what extent C. S. Lewis's Christianity is also a classic Christianity, that is, a Greek and Latin one.

Procedure to characterize microroughness of optical thin films: application to ion-beam-sputtered vacuum-ultraviolet coatings

A method for characterizing the microroughness of samples in optical coating technology is developed. Measurements over different spatial-frequency ranges are composed into a single power spectral density (PSD) covering a large bandwidth. This is followed by the extraction of characteristic parameters through fitting of the PSD to a suitable combination of theoretical models. The method allows us to combine microroughness measurements performed with different techniques, and the fitting procedure can be adapted to any behavior of a combined PSD. The method has been applied to a set of ion-beam-sputtered fluoride vacuum-UV coatings with increasing number of alternative low- and high-index layers. Conclusions about roughness development and microstructural growth are drawn.