An approach to health and safety in E.U. forestry operations – Hazards and preventive measures

Forestry in general and logging in particular continue to be among the three most hazardous sectors in European countries. The aim of this article is to characterize health and safety problems and solutions in E.U. forestry operations, and particularly in Portuguese operations. Forest types, production, employment and ownership are used to characterize the forest sector. Forestry accidents and health problems data are mentioned. Typical hazards associated to the nature of logging operations are systematized. Preventive measures, focused on a wide spectrum of measures, making safety considerations an integral feature of all operational activities from planning to organization to execution and supervision of work are emphasized in this article.

Information technology service management: an experimental approach towards IT service prediction

Dissertation presented to obtain a Masters degree in Computer Science

Anti-vibration gloves and the forearm efforts during tools operations

The objective of this paper is to analyze the forearm muscular contraction levels associated to the use of anti-vibration gloves, by comparing the contraction levels with gloves and without gloves. Two different vibration tools were used in a simulated work environment: (1) A compact Duty Multi-Cutter Bosch and (2) and a Percussion Drill with a drill bit Ø20 mm. Standard operations were performed by each subject in the following materials: (1) Performing cross- sectional cuts in 80x40 mm pine section and (2) performing 20 mm diameter holes in a concrete slab 2 x 2 m, 70 mm thick. The forearm contraction level were measured by surface electromyography in four different muscles: Flexor Digitorum Superficialis (FDS), Flexor Carpi Ulnaris (FCU), Extensor Carpi Radialis Longus (ECRL) e Extensor Carpi Ulnaris (ECU). For the flexor muscles (FDS, FCU), an increase tendency in muscular contraction was observed when the operations are performed without gloves (2-5% MVE increase in the FDS and 3-9% MVE increase in the FCU). For the extensor muscles ECU a decrease tendency in muscular contraction was observed when the operations are performed without gloves (1-10% MVE decrease). Any tendency was found in the ECRL muscle. ECU was the muscle with the highest contraction level for 79% and 71% of the operators, during the operations respectively with the multi-cutter (P50= 27-30%MVE) and with the percussion drill (P50=46-55%MVE). As a final conclusion from this study, anti- vibration gloves may increase the forearm fatigue in the posterior region of the forearm (ECU muscle) during operations with the mentioned tools

Fast-to-fed shift in glucose homeostasis: clues to an earlier detection of human prediabetic states

FCM: UC Bioquímica I - PhD Thesis

Massive shift in the pneumococcal nasopharyngeal flora after the 7-valent conjugate vaccine: epidemiological studies and testing pathogenic potential in animal models

Dissertation presented to obtain the PhD degree in Biology/Molecular Biology by Universidade Nova de Lisboa, Instituto de Tecnologia Química e Biológica

Planning, operations and data handling of planetary science missions

Dissertação para obtenção do Grau de Mestre em Engenharia Física

The impact of banks dimension on profitability, sustainability and efficiency: An analysis for the Iberian financial system

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Management from the NOVA – School of Business and Economics

An internal analysis of Amorim Turismo’s operations regarding food and beverage with a focus on operational efficiency and quality of service

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Management from the NOVA – School of Business and Economics

Quadrature generators based on ring oscillators and shift registers

Quadrature oscillators are key elements in modern radio frequency (RF) transceivers and very useful nowadays in wireless communications, since they can provide: low quadrature error, low phase-noise, and wide tuning range (useful to cover several bands). RC oscillators can be fully integrated without the need of external components (external high Q-inductors), optimizing area, cost, and power consumption. The conventional structure of ring oscillator offers poor frequency stability and phasenoise, low quality factor (Q), and besides being vulnerable to process, voltage and temperature (PVT) variations, its performance degrades as the frequency of operation increases. This thesis is devoted to quadrature oscillators and presents a detailed comparative study of ring oscillator and shift register (SR) approaches. It is shown that in SRs both phase-noise and phase error are reduced, while ring oscillators have the advantage of occupying less area and less consumption due to the reduced number of components in the circuit. Thus, although ring oscillators are more suitable for biomedical applications, SRs are more appropriate for wireless applications, especially when specification requirements are more stringent and demanding. The first architecture studied consists in a simple CMOS ring oscillator employing an odd number of static single-ended inverters as delay cells. Subsequently, the quadrature 4-stage ring oscillator concept is shown and post-layout simulations are presented. The 3 and 4-phase single-frequency local oscillator (LO) generators employing SRs are presented, the latter with 50% and 25% duty-cycles. The circuits operate at 600 MHz and 900 MHz, and were designed in a 130 nm standard CMOS technology with a voltage supply of 1.2 V.

Fuel switching

The present Master dissertation is a project whose main objective is to identify value creation opportunities through fuel switching in the Portuguese industry, services, agriculture and fishing sectors. Fuel switching opportunities are characterized by type of fuel transition, type of technology transition, economy subsectors prone to have fuel switching and value created through fuel shift. Results suggest tomato concentrate, dairy, beer manufacturing and sugar refining subsectors is where prevalence of fuel oil steam boilers is high, for such cases conversion to natural gas steam boilers should result in operations having a ratio of NPV over CAPEX larger than ten and a payback period just under one year. Results further suggest food, beverages, textile, chemicals and wood subsectors currently operate between ten and twenty cogeneration Diesel engines that can be either modified to operate with natural gas or replaced by new natural gas cogeneration systems. Financial modeling indicates that both options have great value creation potential. The current analysis aims to be used by natural gas suppliers and energy project promoters to identify new potential deals as well as by heavy energy consumers to mitigate their energy related costs.