Design of a low-voltage CMOS RF receiver for energy harvesting sensor node

In this thesis a CMOS low-power and low-voltage RF receiver front-end is presented. The main objective is to design this RF receiver so that it can be powered by a piezoelectric energy harvesting power source, included in a Wireless Sensor Node application. For this type of applications the major requirements are: the low-power and low-voltage operation, the reduced area and cost and the simplicity of the architecture. The system key blocks are the LNA and the mixer, which are studied and optimized with greater detail, achieving a good linearity, a wideband operation and a reduced introduction of noise. A wideband balun LNA with noise and distortion cancelling is designed to work at a 0.6 V supply voltage, in conjunction with a double-balanced passive mixer and subsequent TIA block. The passive mixer operates in current mode, allowing a minimal introduction of voltage noise and a good linearity. The receiver analog front-end has a total voltage conversion gain of 31.5 dB, a 0.1 - 4.3 GHz bandwidth, an IIP3 value of -1.35 dBm, and a noise figure lower than 9 dB. The total power consumption is 1.9 mW and the die area is 305x134.5 m2, using a standard 130 nm CMOS technology.

Non-gyrator type active inductors

Modern CMOS radio frequency (RF) Receivers have enabled efficient and increasing applications. The main requirement is to have system in a single chip, in order to minimize area and cost. For the purpose it is required the development of inductorless circuits for the key blocks of an RF receiver. Examples of this key blocks are RC oscillators, RF band pass filters, and Low Noise Amplifiers. The present dissertation presents an inductorless wideband MOSFET-only RF Non-Gyrator Type of Active Inductors with low area, low cost, and very low power, capable of covering the whole WMTS, and ISM, band and intended for biomedical applications. The proposed circuit is based on a floating capacitor connected between two controlled current sources. The first current source, which is controlled by the circuit input voltage, has two objectives: supply current to the capacitor (

Analysis and implementation of a multi-ratio switched capacitor DC-DC converter for a supercapacitor power supply

An energy harvesting system requires an energy storing device to store the energy retrieved from the surrounding environment. This can either be a rechargeable battery or a supercapcitor. Due to the limited lifetime of rechargeable batteries, they need to be periodically replaced. Therefore, a supercapacitor, which has ideally a limitless number of charge/discharge cycles can be used to store the energy; however, a voltage regulator is required to obtain a constant output voltage as the supercapacitor discharges. This can be implemented by a Switched-Capacitor DC-DC converter which allows a complete integration in CMOS technology, although it requires several topologies in order to obtain a high efficiency. This thesis presents the complete analysis of four different topologies in order to determine expressions that allow to design and determine the optimum input voltage ranges for each topology. To better understand the parasitic effects, the implementation of the capacitors and the non-ideal effect of the switches, in 130 nm technology, were carefully studied. With these two analysis a multi-ratio SC DC-DC converter was designed with an output power of 2 mW, maximum efficiency of 77%, and a maximum output ripple, in the steady state, of 23 mV; for an input voltage swing of 2.3 V to 0.85 V. This proposed converter has four operation states that perform the conversion ratios of 1/2, 2/3, 1/1 and 3/2 and its clock frequency is automatically adjusted to produce a stable output voltage of 1 V. These features are implemented through two distinct controller circuits that use asynchronous time machines (ASM) to dynamically adjust the clock frequency and to select the active state of the converter. All the theoretical expressions as well as the behaviour of the whole system was verified using electrical simulations.

Quadrature generators based on ring oscillators and shift registers

Quadrature oscillators are key elements in modern radio frequency (RF) transceivers and very useful nowadays in wireless communications, since they can provide: low quadrature error, low phase-noise, and wide tuning range (useful to cover several bands). RC oscillators can be fully integrated without the need of external components (external high Q-inductors), optimizing area, cost, and power consumption. The conventional structure of ring oscillator offers poor frequency stability and phasenoise, low quality factor (Q), and besides being vulnerable to process, voltage and temperature (PVT) variations, its performance degrades as the frequency of operation increases. This thesis is devoted to quadrature oscillators and presents a detailed comparative study of ring oscillator and shift register (SR) approaches. It is shown that in SRs both phase-noise and phase error are reduced, while ring oscillators have the advantage of occupying less area and less consumption due to the reduced number of components in the circuit. Thus, although ring oscillators are more suitable for biomedical applications, SRs are more appropriate for wireless applications, especially when specification requirements are more stringent and demanding. The first architecture studied consists in a simple CMOS ring oscillator employing an odd number of static single-ended inverters as delay cells. Subsequently, the quadrature 4-stage ring oscillator concept is shown and post-layout simulations are presented. The 3 and 4-phase single-frequency local oscillator (LO) generators employing SRs are presented, the latter with 50% and 25% duty-cycles. The circuits operate at 600 MHz and 900 MHz, and were designed in a 130 nm standard CMOS technology with a voltage supply of 1.2 V.

Switching mode power amplifier for bluetooth applications

Modern fully integrated transceivers architectures, require circuits with low area, low cost, low power, and high efficiency. A key block in modern transceivers is the power amplifier, which is deeply studied in this thesis. First, we study the implementation of a classical Class-A amplifier, describing the basic operation of an RF power amplifier, and analysing the influence of the real models of the reactive components in its operation. Secondly, the Class-E amplifier is deeply studied. The different types of implementations are reviewed and theoretical equations are derived and compared with simulations. There were selected four modes of operation for the Class-E amplifier, in order to perform the implementation of the output stage, and the subsequent comparison of results. This led to the selection of the mode with the best trade-off between efficiency and harmonics distortion, lower power consumption and higher output power. The optimal choice was a parallel circuit containing an inductor with a finite value. To complete the implementation of the PA in switching mode, a driver was implemented. The final block (output stage together with the driver) got 20 % total efficiency (PAE) transmitting 8 dBm output power to a 50 W load with a total harmonic distortion (THD) of 3 % and a total consumption of 28 mW. All implementations are designed using standard 130 nm CMOS technology. The operating frequency is 2.4 GHz and it was considered an 1.2 V DC power supply. The proposed circuit is intended to be used in a Bluetooth transmitter, however, it has a wider range of applications.

Investigation of Novel Circuits Involved in Virgin Female Receptivity of Drosophila melanogaster

Courtship is a behavior that allows the display of fitness of one sex to the other and gates possible subsequent mating. This behavior is crucial for reproduction and has strong innate components in all animals. Courtship in Drosophila melanogaster consists of a series of highly stereotyped actions that the male performs towards the female. He sings with vibrations of the wings, touches and licks her abdomen, while she evaluates the information presented to her.(...)

Cheirogaster sp. (O. Testudines, Fam. Testudinidae, Geochelone sl.) du Paléogène de Naia, Tondela et l’âge du gisement

A land tortoise from a new locality at Naia, Tondela, is described. It is to be reported either to an advanced form of the genus Hadrianus or to an archaic representative of Cheirogaster; it may be included in the comprehensive genus Geochelone s.l., excluding however Ergilemys and its descendants. There is a strong possibility in favour of Cheirogaster. Testudo must also be excluded. It is not possible to classify this specimen at species'level. Our specimen does agree best with Upper Eocene Testudinidae and with some Lower Oligocene ones. Its age is certainly not Upper Oligocene or later, nor Lower and Middle Eocene. This datation is not opposed to the age of the fossiliferous clays of Naia as supposed by correlation with another locality - Côja, about 30 km to the South - which yielded an assemblage of mammals whose Ludian (Upper Bartonian s.l.) age seems well established. Naia and Côja's fossil-bearing clays must be nearly synchronous; their origin is well in place among the phenomena related to the surrection of iberian Central Chain during paroxysmal phase of pyrenean orogenesis.

Palinomorfos ante-cenomanianos do «Grés do Buçaco» (Lousã, Portugal)

The palynological study of sediments from lower levels of Lousã basin (Lomba do Alveite Arkoses), is presented. The palynological association includes several species of Appendicisporites and Cicatricosisporites, Costatoperforosporites sp., Ischyosporites teixeirae, Pattelasporites tavaredensis, Echinatisporis sp., Spheripollenites perinatus, Tricolpopollenites sp. and Retitricolpites maximus. The presence of the last two forms; and the absence of Normapolles, suggest an ante-Cenomanian, most probably Albian age for the assemblage. From these results, the begining of the infilling of the Lousã basin, is, at least in part, synchronous with the deposition of the «Grés Grosseiro Inferior» from the Occidental portuguese Basin. The presence of Lower Cretaceous Basin, is shown for the first time.

An introduction to the fractional continuous-time linear systems

A brief introduction to the fractional continuous-time linear systems is presented. It will be done without needing a deep study of the fractional derivatives. We will show that the computation of the impulse and step responses is very similar to the classic. The main difference lies in the substitution of the exponential by the Mittag-Leffler function. We will present also the main formulae defining the fractional derivatives.

Efficient middleware for database replication

Dissertação de Mestrado em Engenharia Informática

Compact SMB chromatography for binary separation

A thesis submitted for the degree of Doctor of Philosophy

An introduction to the fractional continuous- time linear systems: the 21st century systems

IEEE CIRCUITS AND SYSTEMS MAGAZINE, Third Quarter

New quasi-orthogonal BCH-derived sequences for CDMA applications

European Transactions on Telecommunications, vol. 18

Fully transparent ZnO thin-film transistor produced at room temperature

Advanced Materials, Vol. 17, nº 5

New simple digital self-calibration technique for pipeline ADCs using the internal thermal noise

IEEE International Symposium on Circuits and Systems, pp. 232 – 235, Seattle, EUA