Fractional discrete-time signal processing: scale conversion and linear prediction

Nonlinear Dynamics, Vol. 29

Introduction to fractional linear systems. Part 1 : continuous-time case

IEE Proceedings - Vision, Image, and Signal Processing, Vol. 147, nº 1

Introduction to fractional linear systems. Part 2: discrete-time case

IEE Proceedings - Vision, Image, and Signal Processing, Vol. 147, nº 1

A fractional linear system view of the fractional brownian motion

Nonlinear Dynamics, Vol. 38

Modelação e controlo não-linear do sistema motor humano

Mestrado Integrado em Engenharia Electrotécnica e de Computadores

New results on fractional linear prediction

Proceedings of the European Control Conference, ECC’01, Porto, Portugal, September 2001

Land use/ land cover change and its impact on soil erosion process in Begnas Tal Rupa Tal watershed using geospatial tools, Kaski district, Nepal

Dissertation submitted in partial fulfilment of the requirements for the Degree of Master of Science in Geospatial Technologies

Electron and photon induced processes in SF5CF3

The photo-absorption cross section of trifluoromethyl sulphur pentafluoride, SF5CF3 has been measured using synchrotron radiation in the range of 4–11 eV (310 nm > l > 110 nm) and comparison made with electron energy loss spectroscopy (EELS). The measured VUV cross sections are used to derive the photolysis rate of SF5CF3 in the terrestrial atmosphere. It is estimated that the lifetime for this molecule is the order of a 1000 years and the calculated global warming potential (GWP) is found to be between 17000 and 18100, making it one of the most potent global warming gases in the terrestrial atmosphere.

Multi-bit sigma-delta modulators with enhanced dynamic-range using non-linear DAC for hearing aids

15th IEEE International Conference on Electronics, Circuits and Systems, Malta

Applications of Fourier methods to the analysis of some stochastic processes

Dissertação de Doutoramento em Matemática: Processos Estocásticos

Post-processing Techniques in Free Boundary Flows during Liquid Composite Moulding Processes

Post-processing a finite element solution is a well-known technique, which consists in a recalculation of the originally obtained quantities such that the rate of convergence increases without the need for expensive remeshing techniques. Postprocessing is especially effective in problems where better accuracy is required for derivatives of nodal variables in regions where Dirichlet essential boundary condition is imposed strongly. Consequently such an approach can be exceptionally good in modelling of resin infiltration under quasi steady-state assumption by remeshing techniques and with explicit time integration, because only the free-front normal velocities are necessary to advance the resin front to the next position. The new contribution is the post-processing analysis and implementation of the freeboundary velocities of mesolevel infiltration analysis. Such implementation ensures better accuracy on even coarser meshes, which in consequence reduces the computational time also by the possibility of employing larger time steps.

Mass Conservation Enhancement of Free Boundary Mesolevel Flows during LCM Processes of Composites Manufacturing

Undesirable void formation during the injection phase of the liquid composite moulding process can be understood as a consequence of the non-uniformity of the flow front progression, caused by the dual porosity of the fibre perform. Therefore the best examination of the void formation physics can be provided by a mesolevel analysis, where the characteristic dimension is given by the fibre tow diameter. In mesolevel analysis, liquid impregnation along two different scales; inside fibre tows and within the open spaces between them; must be considered and the coupling between these flow regimes must be addressed. In such case, it is extremely important to account correctly for the surface tension effects, which can be modelled as capillary pressure applied at the flow front. Numerical implementation of such boundary conditions leads to ill-posing of the problem, in terms of the weak classical as well as stabilized formulation. As a consequence, there is an error in mass conservation accumulated especially along the free flow front. This contribution presents a numerical procedure, which was formulated and implemented in the existing Free Boundary Program in order to significantly reduce this error.

La cuirasse ferrugineuse conglomératique de Cabatuquila (Malanje - R. P. d'Angola) et sa signification paléogéographique

Cabatuquila conglomerate ferricrete (Malanje Province, located North Central Angola) corresponds to a thick (1O-15m) and hardcornice at the top of "Baixa de Cassanje" escarpment. "Baixa de Cassanje" is a large graben part of South Congo basin. Cabatuquila conglomerate ferricrete seems to correspond to a Plio-Pleistocene morphology which has already disappeared. Laterization dynamics and ferricrete formation processes took place on the Tertiary surface, before being tilted to the Congo Basin. Materials submitted to these processes are mainly alluvial deposits from a pre-Cuanza drainage system. This drainage system flowed to the North before being captured to the Atlantic, as a consequence of the movement which deformed the Tertiary surface during the Pleistocene. The erosion dynamics, which created the Cassanje depression, has occurred after the late Tertiary surface deformation. That dynamics might be related to the Cuango drainage system, which was reorganized after that deformation.

A sedimentação e a gliptogénese no registo cenozóico continental do Minho (NW Portugal)

This study identifies and describes the major Cenozoíc glyptogenesis and sedimentation episodes in the Minho region (NW Portugal). The fluvial processes of exorheic network were mainly the builders of Cenozoic landscape. This paper presents a chronological sequence of the major fluvial events based on geomorphology and sedimentary characteristics obtained in former studies and new ones. The oldest Cenozoic sedimentation (Placencian) remains on local depressions and was generated by fluvial and fluvio-lacustrine processes. Quaternary glyptogenesis begins probably with a major European cooling (Gunz?). So, the Placencian infilling was eroded and a new episode of sedimentation was accumulated in the same early paleovalley. There were three more cycles of quaternary glyptogenesis and sedimentation. The last glyptogenesis episode records the last glacial period. The post-glacial alluvion contains clasts of granites, schists, feldspats, and other alterable lithologies and minerals; on clay dimensions there are abundant illite and interstratified minerals. This composition differs from the older ones, more siliciclastic and kaolinitic. Other minor erosion episodes were identified, controlled manly by eustasy; evidences of tectonic movements were observed only in rio Minho valley.

Development of thermoresponsive (polysulfone/polyacrylonitrile) - based membranes for bioseparation processes

Mestrado integrado em Engenharia Química e Bioquímica