Characterization of an OPCPA laser amplifier based on the nonlinear crystal YCOB

The work described in this thesis was performed at the Laboratory for Intense Lasers (L2I) of Instituto Superior Técnico, University of Lisbon (IST-UL). Its main contribution consists in the feasibility study of the broadband dispersive stages for an optical parametric chirped pulse amplifier based on the nonlinear crystal yttrium calcium oxi-borate (YCOB). In particular, the main goal of this work consisted in the characterization and implementation of the several optical devices involved in pulse expansion and compression of the amplified pulses to durations of the order of a few optical cycles (20 fs). This type of laser systems find application in fields such as medicine, telecommunications and machining, which require high energy, ultrashort (sub-100 fs) pulses. The main challenges consisted in the preliminary study of the performance of the broadband amplifier, which is essential for successfully handling pulses with bandwidths exceeding 100 nm when amplified from the μJ to 20 mJ per pulse. In general, the control, manipulation and characterization of optical phenomena on the scale of a few tens of fs and powers that can reach the PW level are extremely difficult and challenging due to the complexity of the phenomena of radiation-matter interaction and their nonlinearities, observed at this time scale and power level. For this purpose the main dispersive components were characterized in detail, specifically addressing the demonstration of pulse expansion and compression. The tested bandwidths are narrower than the final ones, in order to confirm the parameters of these elements and predict the performance for the broadband pulses. The work performed led to additional tasks such as a detailed characterization of laser oscillator seeding the laser chain and the detection and cancelling of additional sources of dispersion.

Recuperação renovável de Mg a partir de MgO através da utilização concertada de laser solar e de concentrador solar

Apesar do elevado potencial do metal magnésio como material útil em várias áreas cien-tíficas e tecnológicas, os seus métodos de produção tradicionais têm um impacto fortemente prejudicial no ambiente e um custo elevado. Este facto é um incentivo à procura de novas so-luções, nomeadamente as que recorrem à utilização da radiação solar partindo do óxido de magnésio. Alguns estudos têm já sido feitos nesse sentido, utilizando laser solar ou radiação solar concentrada mas a utilização concertada dos dois não tinha sido feita até ao momento. Neste trabalho, a exequibilidade da utilização concertada destes dois métodos será avaliada e será estudado o comportamento do óxido de magnésio face à radiação que nele incide.

Melhoramento e automatização de um sistema de revestimento com laser

O revestimento com laser permite criar revestimentos localizados pela adição de uma liga similar ou dissimilar. O revestimento visa melhorar as características da superfície metálica, tais como a dureza, a resistência ao desgaste por atrito, à corrosão e à fadiga térmica dos componentes sujeitos a condições adversas de trabalho por prolongados períodos de tempo. Esta dissertação tem como objetivo o melhoramento da configuração, a automatização do sistema de revestimento com laser do Laboratório de Laser do Instituto Superior Técnico (IST) da Universidade de Lisboa, utilizado pelo Centro de Física e Engenharia de Materiais Avançados do Instituto Superior Técnico – CeFEMA e a realização de ensaios de deposições com o fim de validação. Foram estudadas as configurações possíveis para o sistema de posicionamento da amostra, do laser e a configuração para o posicionamento com precisão do bocal de adição de pós ao banho de fusão. Após este estudo foram apresentadas e implementadas as propostas de melhoria do sistema inicial. Para tornar o sistema funcional, foi desenvolvido um controlador para comandar as três guias motorizadas de movimento linear OWIS, o laser IPG YLR e o alimentador de pós PLASMA-TECHNIK. Para simplificar a utilização aos investigadores do CeFEMA foi ainda desenvolvida uma interface gráfica que permite ao utilizador definir os principais parâmetros do processo Para a validação do trabalho desenvolvido foram realizados diversos ensaios de deposição da liga Ti52Ta num substrato de titânio. Através dos ensaios de deposição foi estudada a influência de alguns parâmetros do processo na geometria do revestimento obtido, como a altura, a profundidade, o ângulo do cordão, a diluição entre o material de adição e o substrato, tendo ainda sido estudada a influência dos parâmetros do processo na eficiência de deposição.

Radiation damage in flexible TFTs and organic detectors

In this thesis was investigated the radiation hardness of the building blocks of a future flexible X-ray sensor system. The characterized building blocks for the pixel addressing and signal amplification electronics are high mobility semiconducting oxide transistors (HMSO-TFTs) and organic transistors (OTFTs), whereas the photonic detection system is based on organic semiconducting single crystals (OSSCs). TFT parameters such as mobility, threshold voltage and subthreshold slope were measured as function of cumulative X-ray dose. Instead for OSSCs conductivity and X-ray sensitivity were analysed after various radiation steps. The results show that ionizing radiation does not lead to degradation in HMSO-TFTs. Instead OTFTs show instability in mobility which is reduced up to 73% for doses of 1 kGy. OSSC demonstrate stable detector properties for the tested total dose range. As conclusion, HMSO-TFTs and OSSCs can be readily employed in the X-ray detector system allowing operation for total doses exceeding 1 kGy of ionizing radiation.

Building 3D City Models: Testing and Comparing Laser Scanning and Low-Cost UAV Data Using FOSS Technologies

Contém resumo

Damage propagation in composite Materials meso-mechanical models

Composite materials have a complex behavior, which is difficult to predict under different types of loads. In the course of this dissertation a methodology was developed to predict failure and damage propagation of composite material specimens. This methodology uses finite element numerical models created with Ansys and Matlab softwares. The methodology is able to perform an incremental-iterative analysis, which increases, gradually, the load applied to the specimen. Several structural failure phenomena are considered, such as fiber and/or matrix failure, delamination or shear plasticity. Failure criteria based on element stresses were implemented and a procedure to reduce the stiffness of the failed elements was prepared. The material used in this dissertation consist of a spread tow carbon fabric with a 0°/90° arrangement and the main numerical model analyzed is a 26-plies specimen under compression loads. Numerical results were compared with the results of specimens tested experimentally, whose mechanical properties are unknown, knowing only the geometry of the specimen. The material properties of the numerical model were adjusted in the course of this dissertation, in order to find the lowest difference between the numerical and experimental results with an error lower than 5% (it was performed the numerical model identification based on the experimental results).

Welle tecnologia laser internationalization analysis US market

Welle Laser is a Brazilian company that manufactures marking and engraving machines mainly for large-scale industry segments providing solutions that help increase productivity. Welle laser has 60% market share in Brazil and decided to go internationally in 2015, mainly to increase revenues and diversify business risks. Welle opened an office in Switzerland and celebrated a contract with a Mexican company to distribute their machines in Mexico. The next step for Welle is expanding its operation to USA. In my project I accessed the viability and reasons to enter the US market, the region where Welle should start its operation, and the best entry mode strategy.