Thermodynamic pathway for the formation of SnSe and SnSe2 polycrystalline thin films by selenization of metal precursors

In this work, tin selenide thin films (SnSex) were grown on soda lime glass substrates by selenization of dc magnetron sputtered Sn metallic precursors. Selenization was performed at maximum temperatures in the range 300 °C to 570 °C. The thickness and the composition of the films were analysed using step profilometry and energy dispersive spectroscopy, respectively. The films were structurally and optically investigated by X-ray diffraction, Raman spectroscopy and optical transmittance and reflectance measurements. X-Ray diffraction patterns suggest that for temperatures between 300 °C and 470 °C, the films are composed of the hexagonal-SnSe2 phase. By increasing the temperature, the films selenized at maximum temperatures of 530 °C and 570 °C show orthorhombic-SnSe as the dominant phase with a preferential crystal orientation along the (400) crystallographic plane. Raman scattering analysis allowed the assignment of peaks at 119 cm−1 and 185 cm−1 to the hexagonal-SnSe2 phase and those at 108 cm−1, 130 cm−1 and 150 cm−1 to the orthorhombic-SnSe phase. All samples presented traces of condensed amorphous Se with a characteristic Raman peak located at 255 cm−1. From optical measurements, the estimated band gap energies for hexagonal-SnSe2 were close to 0.9 eV and 1.7 eV for indirect forbidden and direct transitions, respectively. The samples with the dominant orthorhombic-SnSe phase presented estimated band gap energies of 0.95 eV and 1.15 eV for indirect allowed and direct allowed transitions, respectively.

Cu2ZnSnS4 absorber layers obtained through sulphurization of metallic precursors: Graphite box versus sulphur flux

In this work we employed a hybrid method, combining RF-magnetron sputtering with evaporation, for the deposition of tailor made metallic precursors, with varying number of Zn/Sn/Cu (ZTC) periods and compared two approaches to sulphurization. Two series of samples with 1×, 2× and 4× ZTC periods have been prepared. One series of precursors was sulphurized in a tubular furnace directly exposed to a sulphur vapour and N2+5% H2 flux at a pressure of 5.0×10+4 Pa. A second series of identical precursors was sulphurized in the same furnace but inside a graphite box where sulphur pellets have been evaporated again in the presence of N2+5% H2 and at the same pressure as for the sulphur flux experiments. The morphological and chemical analyses revealed a small grain structure but good average composition for all three films sulphurized in the graphite box. As for the three films sulphurized in sulphur flux grain growth was seen with the increase of the number of ZTC periods whilst, in terms of composition, they were slightly Zn poor. The films' crystal structure showed that Cu2ZnSnS4 is the dominant phase. However, in the case of the sulphur flux films SnS2 was also detected. Photoluminescence spectroscopy studies showed an asymmetric broad band emission whichoccurs in the range of 1–1.5 eV. Clearly the radiative recombination efficiency is higher in the series of samples sulphurized in sulphur flux. We have found that sulphurization in sulphur flux leads to better film morphology than when the process is carried out in a graphite box in similar thermodynamic conditions. Solar cells have been prepared and characterized showing a correlation between improved film morphology and cell performance. The best cells achieved an efficiency of 2.4%.

CuxSnSx+1 (x = 2, 3) thin films grown by sulfurization of metallic precursors deposited by dc magnetron sputtering

We report the results of the growth of Cu-Sn-S ternary chalcogenide compounds by sulfurization of dc magnetron sputtered metallic precursors. Tetragonal Cu2SnS3 forms for a maximum sulfurization temperature of 350 ºC. Cubic Cu2SnS3 is obtained at sulfurization temperatures above 400 ºC. These results are supported by XRD analysis and Raman spectroscopy measurements. The latter analysis shows peaks at 336 cm-1, 351 cm-1 for tetragonal Cu2SnS3, and 303 cm-1, 355 cm-1 for cubic Cu2SnS3. Optical analysis shows that this phase change lowers the band gap from 1.35 eV to 0.98 eV. At higher sulfurization temperatures increased loss of Sn is expected in the sulphide form. As a consequence, higher Cu content ternary compounds like Cu3SnS4 grow. In these conditions, XRD and Raman analysis only detected orthorhombic (Pmn21) phase (petrukite). This compound has Raman peaks at 318 cm-1, 348 cm-1 and 295 cm-1. For a sulfurization temperature of 450 ºC the samples present a multi-phase structure mainly composed by cubic Cu2SnS3 and orthorhombic (Pmn21) Cu3SnS4. For higher temperatures, the samples are single phase and constituted by orthorhombic (Pmn21) Cu3SnS4. Transmittance and reflectance measurements were used to estimate a band gap of 1.60 eV. For comparison we also include the results for Cu2ZnSnS4 obtained using similar growth conditions.

Assessment of the potential of tin sulphide thin films prepared by sulphurization of metallic precursors as cell absorbers

In this work, SnxSy thin films have been grown on soda-lime glass substrates by sulphurization of metallic precursors in a nitrogen plus sulphur vapour atmosphere. Different sulphurization temperatures were tested, ranging from 300 °C to 520 °C. The resulting phases were structurally investigated by X-Ray Diffraction and Raman spectroscopy. Composition was studied using Energy Dispersive Spectroscopy being then correlated with the sulphurization temperature. Optical measurements were performed to obtain transmittance and reflectance spectra, from which the energy band gaps, were estimated. The values obtained were 1.17 eV for the indirect transition and for the direct transition the values varied from 1.26 eV to 1.57 eV. Electrical characterization using Hot Point Probe showed that all samples were p-type semiconductors. Solar cells were built using the structure: SLG/Mo/SnxSy/CdS/ZnO:Ga and the best result for solar cell efficiency was 0.17%.

Precursors’ order effect on the properties of sulfurized Cu2ZnSnS4 thin films

A dc magnetron sputtering-based method to grow high-quality Cu2ZnSnS4 (CZTS) thin films, to be used as an absorber layer in solar cells, is being developed. This method combines dc sputtering of metallic precursors with sulfurization in S vapour and with post-growth KCN treatment for removal of possible undesired Cu2−xS phases. In this work, we report the results of a study of the effects of changing the precursors’ deposition order on the final CZTS films’ morphological and structural properties. The effect of KCN treatment on the optical properties was also analysed through diffuse reflectance measurements. Morphological, compositional and structural analyses of the various stages of the growth have been performed using stylus profilometry, SEM/EDS analysis, XRD and Raman Spectroscopy. Diffuse reflectance studies have been done in order to estimate the band gap energy of the CZTS films. We tested two different deposition orders for the copper precursor, namely Mo/Zn/Cu/Sn and Mo/Zn/Sn/Cu. The stylus profilometry analysis shows high average surface roughness in the ranges 300–550 nm and 230–250 nm before and after KCN treatment, respectively. All XRD spectra show preferential growth orientation along (1 1 2) at 28.45◦. Raman spectroscopy shows main peaks at 338 cm−1 and 287 cm−1 which are attributed to Cu2ZnSnS4. These measurements also confirm the effectiveness of KCN treatment in removing Cu2−xS phases. From the analysis of the diffuse reflectance measurements the band gap energy for both precursors’ sequences is estimated to be close to 1.43 eV. The KCN-treated films show a better defined absorption edge; however, the band gap values are not significantly affected. Hot point probe measurements confirmed that CZTS had p-type semiconductor behaviour and C–V analysis was used to estimate the majority carrier density giving a value of 3.3 × 1018 cm−3.

Growth and Raman scattering characterization of Cu2ZnSnS4 thin films

In the present work we report the results of the growth, morphological and structural characterization of Cu2ZnSnS4 (CZTS) thin films prepared by sulfurization of DC magnetron sputtered Cu/Zn/Sn precursor layers. The adjustment of the thicknesses and the properties of the precursors were used to control the final composition of the films. Its properties were studied by SEM/EDS, XRD and Raman scattering. The influence of the sulfurization temperature on the morphology, composition and structure of the films has been studied. With the presented method we have been able to prepare CZTS thin films with the kesterite structure.

Photoluminescence and electrical study of fluctuating potentials in Cu2ZnSnS4-based thin films

In this work, we investigated structural, morphological, electrical, and optical properties from a set of Cu2ZnSnS4 thin films grown by sulfurization of metallic precursors deposited on soda lime glass substrates coated with or without molybdenum. X-ray diffraction and Raman spectroscopy measurements revealed the formation of single-phase Cu2ZnSnS4 thin films. A good crystallinity and grain compactness of the film was found by scanning electron microscopy. The grown films are poor in copper and rich in zinc, which is a composition close to that of the Cu2ZnSnS4 solar cells with best reported efficiency. Electrical conductivity and Hall effect measurements showed a high doping level and a strong compensation. The temperature dependence of the free hole concentration showed that the films are nondegenerate. Photoluminescence spectroscopy showed an asymmetric broadband emission. The experimental behavior with increasing excitation power or temperature cannot be explained by donor-acceptor pair transitions. A model of radiative recombination of an electron with a hole bound to an acceptor level, broadened by potential fluctuations of the valence-band edge, was proposed. An ionization energy for the acceptor level in the range 29–40 meV was estimated, and a value of 172 ±2 meV was obtained for the potential fluctuation in the valence-band edge.

Study of optical and structural properties of Cu2ZnSnS4 thin films

Cu2ZnSnS4 is a promising semiconductor to be used as absorber in thin film solar cells. In this work, we investigated optical and structural properties of Cu2ZnSnS4 thin films grown by sulphurization of metallic precursors deposited on soda lime glass substrates. The crystalline phases were studied by X-ray diffraction measurements showing the presence of only the Cu2ZnSnS4 phase. The studied films were copper poor and zinc rich as shown by inductively coupled plasma mass spectroscopy. Scanning electron microscopy revealed a good crystallinity and compactness. An absorption coefficient varying between 3 and 4×104cm−1 was measured in the energy range between 1.75 and 3.5 eV. The band gap energy was estimated in 1.51 eV. Photoluminescence spectroscopy showed an asymmetric broad band emission. The dependence of this emission on the excitation power and temperature was investigated and compared to the predictions of the donor-acceptor-type transitions and radiative recombinations in the model of potential fluctuations. Experimental evidence was found to ascribe the observed emission to radiative transitions involving tail states created by potential fluctuations.

eTourismGUI - Adaptative Interface

Mestrado em Engenharia Informática. Área de Especialização em Tecnologias do Conhecimento e Decisão.

Integração de informação entre Sistemas Geracionais distintos: uma experiência e sistematização na ITV

A natural evolução dos sistemas de informação nas organizações envolve por um lado a instalação de equipamentos actualizados, e por outro a adopção de novas aplicações de suporte ao negócio, acompanhando o desenvolvimento dos mercados, as mudanças no modelo de negócio e a maturação da organização num novo contexto. Muitas vezes esta evolução implica a preservação dos dados existentes e de funcionalidades não cobertas pelas novas aplicações. Este facto leva ao desenvolvimento e execução de processos de migração de dados, de aplicações, e de integração de sistemas legados. Estes processos estão condicionados ao meio tecnológico disponível e ao conhecimento existente sobre os sistemas legados, sendo sensíveis ao contexto em que se desenrolam. Esta dissertação apresenta um estado da arte das abordagens à migração e integração, descreve as diversas alternativas, e ilustra de uma forma sistematizada e comparativa os exercícios realizados usando diferentes abordagens, num ambiente real de migração e integração em mudança.

Coaching: caraterísticas do coach e benefícios do coaching para o cliente

Na atual conjuntura, em que as organizações enfrentam múltiplos desafios pela natureza complexa, incerta e volátil da própria envolvente, torna-se imprescindível conhecer e compreender quais as ferramentas que auxiliam a um maior aproveitamento e desenvolvimento do capital humano (Pina e Cunha et al., 2010). Pelas constantes mudanças tecnológicas, de mercados, políticas e sociais as pessoas têm que se ir adaptando, e o Coaching pode ser uma resposta para as presentes contingências. A importância do Coaching é revelada em diversos estudos pela sua eficácia e respetivos benefícios. Deste modo, faz todo o sentido querer estudar a ferramenta, tendo como objetivo principal querer perceber se as caraterísticas do coach interferem com os benefícios do respetivo cliente. A investigação é apoiada por uma metodologia quantitativa, que testa as hipóteses criadas, de encontro aos objetivos gerais. Em suma, o trabalho é valioso para o crescimento e maturação do Coaching, ao fornecer novos dados.

Wine and grape polyphenols — a chemical perspective

Phenolic compounds constitute a diverse group of secondary metabolites which are present in both grapes and wine. The phenolic content and composition of grape processed products (wine) are greatly influenced by the technological practice to which grapes are exposed. During the handling and maturation of the grapes several chemical changes may occur with the appearance of new compounds and/or disappearance of others, and consequent modification of the characteristic ratios of the total phenolic content as well as of their qualitative and quantitative profile. The non-volatile phenolic qualitative composition of grapes and wines, the biosynthetic relationships between these compounds, and the most relevant chemical changes occurring during processing and storage will be highlighted in this review.

Acompanhamento do Processo de Compostagem e Identificação de Hipóteses de Melhoria, Tendo em Vista a Valorização do Produto Comercializado

A compostagem tem-se revelado uma boa alternativa na gestão, tratamento e valorização de resíduos sólidos urbanos. Dependendo das matérias-primas usadas no processo, os produtos podem ser considerados fertilizantes/corretivos orgânicos com utilidade agrícola. A Suldouro, Valorização e Tratamento de Resíduos Sólidos Urbanos, S.A., é responsável pela gestão, valorização, recuperação e destino final dos Resíduos Sólidos Urbanos (RSU) produzidos em Vila Nova de Gaia e Santa Maria da Feira. Um dos processos do sistema de gestão é a valorização orgânica, que através da compostagem dos resíduos biodegradáveis origina um corretivo orgânico, denominado comercialmente de Agrovida. O objetivo deste trabalho foi caracterizar o composto produzido na Suldouro através da análise de alguns metais, nomeadamente cobre, zinco e chumbo, pois o seu teor condiciona a classe em que o composto está inserido, e da avaliação da razão C/N, visto ser um parâmetro importante para o desenvolvimento dos microrganismos. Um outro objetivo foi a determinação do tempo ótimo de compostagem, através da avaliação da temperatura máxima, recorrendo ao teste de auto-aquecimento usando vasos de Dewar. O estudo da presença de chumbo não chegou a ser realizado, pois a sua concentração era muito baixa (da ordem dos ppb), ou seja, não era limitativa para a utilização do composto. Quanto à análise de cobre e zinco no composto verificou-se que era necessário fazer alterações no processo, no sentido de reduzir estes valores, tanto a nível da qualidade dos resíduos usados como matéria-prima como a nível da limpeza, essencial depois das operações de manutenção aos pulpers. Em relação à razão C/N esta apresenta valores muito elevados, ou seja, uma quantidade de azoto total muito baixa, indicativa de que seria necessário acrescentar, no início do processo, resíduos mais ricos em azoto. A análise do teste de auto-aquecimento indica que o tempo necessário para a estabilização e maturação das pilhas de compostagem é superior a 3 meses. Assim, sugerem-se melhorias a nível da qualidade do resíduo, tentando incluir resíduos mais facilmente biodegradáveis, uma redução da altura da pilha proporcionando um melhor arejamento ou em alternativa proceder periodicamente ao seu revolvimento como complemento à insuflação de ar. Para concluir, neste trabalho foi realizada uma pesquisa sobre processos de valorização energética, alternativas potenciais à valorização orgânica, tendo sido dado especial relevo a um dos processos, a carbonização hidrotérmica (HTC).