Ecotoxicity tests using the green algae chlorella vulgaris — a useful tool in hazardous effluents management

The treatment efficiency of laboratory wastewaters was evaluated and ecotoxicity tests with Chlorella vulgaris were performed on them to assess the safety of their environmental discharge. For chemical oxygen demand wastewaters, chromium (VI), mercury (II) and silver were efficiently removedby chemical treatments.Areduction of ecotoxicitywas achieved; nevertheless, an EC50 (effective concentration that causes a 50% inhibition in the algae growth) of 1.5% (v/v) indicated still high level of ecotoxicity. For chloride determination wastewaters, an efficient reduction of chromium and silver was achieved after treatment. Regarding the reduction of ecotoxicity observed, EC50 increased from 0.059% to 0.5%, only a 0.02% concentration in the aquatic environment would guarantee no effects. Wastewaters containing phenanthroline/iron (II) complex were treated by chemical oxidation. Treatmentwas satisfactory concerning chemical parameters, although an increase in ecotoxicitywas observed (EC50 reduced from 0.31% to 0.21%). The wastes from the kinetic study of persulphate and iodide reaction were treated with sodium bisulphite until colour was removed. Although they did not reveal significant ecotoxicity, only over 1% of the untreated waste produced observable effects over algae. Therefore, ecotoxicity tests could be considered a useful tool not only in laboratory effluents treatment, as shown, but also in hazardous wastewaters management.

Análise da problemática da exposição dos músicos ao ruído: perceção ao ruído e determinação dos níveis de pressão sonora na prática musical em contexto escolar

A atenção face dada à problemática da perda auditiva induzida pelo ruído nos profissionais da música tem sido enfatizada estudos nos últimos anos. No entanto, no que respeita aos alunos de música, são ainda poucos os estudos que analisam esta problemática de modo a permitir compreender se estes poderão estar expostos a elevados níveis de ruído no decorrer da sua formação e desenvolver problemas auditivos. O presente estudo pretende caraterizar os níveis de pressão sonora a que alunos de música estão expostos no decorrer das aulas e analisar a perceção do risco dos mesmos e potenciais efeitos sobre o sistema auditivo. Foram analisadas duas Orquestras de Jazz e uma Orquestra Sinfónica de uma Escola Superior de Música (ESM) e de um Conservatório de Música (CM). No total foram selecionados 24 alunos de acordo com o seu instrumento, e medidos os níveis de pressão sonora em diversas aulas, ao longo de duas semanas com recurso a 8 dosímetros. Foi aplicado um questionário para a análise da perceção dos alunos ao ruído e realizados exames audiométricos para a avaliação auditiva dos alunos. Em geral, os resultados demostraram que os alunos estão expostos a níveis elevados de ruído no decurso das aulas de instrumento e ensaios. Foram obtidos elevados níveis de Lp,A,eqT na bateria, vibrafone, saxofone, trombone, clarinete e trompa. Nas três escolas, verificou-se valores mais baixos de exposição no contrabaixo, nomeadamente nas Aulas Individuais. Os valores de Lp,Cpico ultrapassaram o valor de ação inferior de 135 dB(C) na percussão e saxofone. Nas aulas teóricas os valores obtidos ultrapassaram recomendação de 35 dB(A). No que respeita à perceção dos alunos verificou-se que em geral consideram que a exposição a elevados níveis de pressão sonora não tem efeitos significativos na saúde. Apesar de se ter verificado que todos os alunos avaliados apresentam uma audição normal, tinnitus, hiperacusia, distorção e diplacusia foram identificados por um número significativo de alunos. Os resultados obtidos neste estudo refletem a necessidade de implementação de medidas de prevenção e controlo dos níveis de exposição dos alunos de música com vista a um aumento da sua consciencialização do risco.

Role of abrasive material on micro-abrasion wear tests

Micro-abrasion wear tests with ball-cratering configuration are widely used. Sources of variability are already studied by different authors and conditions for testing are parameterized by BS EN 1071-6: 2007 standard which refers silicon carbide as abrasive. However, the use of other abrasives is possible and allowed. In this work, ball-cratering wear tests were performed using four different abrasive particles of three dissimilar materials: diamond, alumina and silicon carbide. Tests were carried out under the same conditions on a steel plate provided with TiB2 hard coating. For each abrasive, five different test durations were used allowing understanding the initial wear phenomena. Composition and shape of abrasive particles were investigated by SEM and EDS. Scar areas were observed by optical and electronic microscopy in order to understand the wear effects caused by each of them. Scar geometry and grooves were analyzed and compared. Wear coefficient was calculated for each situation. It was observed that diamond particles produce well-defined and circular wear scars. Different silicon carbide particles presented dissimilar results as consequence of distinct particle shape and size distribution.

Influence of the abrasive particles size in the micro-abrasion wear tests of TiAlSiN thin coatings

Ball rotating micro-abrasion tribometers are commonly used to carry out wear tests on thin hard coatings. In these tests, different kinds of abrasives were used, as alumina (Al2O3), silicon carbide (SiC) or diamond. In each kind of abrasive, several particle sizes can be used. Some studies were developed in order to evaluate the influence of the abrasive particle shape in the micro-abrasion process. Nevertheless, the particle size was not well correlated with the material removed amount and wear mechanisms. In this work, slurry of SiC abrasive in distilled water was used, with three different particles size. Initial surface topography was accessed by atomic force microscopy (AFM). Coating hardness measurements were performed with a micro-hardness tester. In order to evaluate the wear behaviour, a TiAlSiN thin hard film was used. The micro-abrasion tests were carried out with some different durations. The abrasive effect of the SiC particles was observed by scanning electron microscopy (SEM) both in the films (hard material) as in the substrate (soft material), after coating perforation. Wear grooves and removed material rate were compared and discussed.

Efficient schedulability tests for real-time embedded systems with urgent routines

Task scheduling is one of the key mechanisms to ensure timeliness in embedded real-time systems. Such systems have often the need to execute not only application tasks but also some urgent routines (e.g. error-detection actions, consistency checkers, interrupt handlers) with minimum latency. Although fixed-priority schedulers such as Rate-Monotonic (RM) are in line with this need, they usually make a low processor utilization available to the system. Moreover, this availability usually decreases with the number of considered tasks. If dynamic-priority schedulers such as Earliest Deadline First (EDF) are applied instead, high system utilization can be guaranteed but the minimum latency for executing urgent routines may not be ensured. In this paper we describe a scheduling model according to which urgent routines are executed at the highest priority level and all other system tasks are scheduled by EDF. We show that the guaranteed processor utilization for the assumed scheduling model is at least as high as the one provided by RM for two tasks, namely 2(2√−1). Seven polynomial time tests for checking the system timeliness are derived and proved correct. The proposed tests are compared against each other and to an exact but exponential running time test.