Análise da atual unidade de desasfaltação pelo Propano para o tratamento de crudes não parafínicos

Este trabalho teve como principal objetivo o estudo da simulação da unidade de destilação atmosférica e a vácuo da fábrica de óleos base da Petrogal, permitindo verificar que, uma vez conseguido um modelo num programa de simulação que traduz o comportamento real de um dado processo, é possível sem riscos operacionais avaliar o efeito da alteração das condições normais de funcionamento desse processo. O trabalho foi orientado pelo Eng.º Carlos Reis, no que diz respeito à empresa, e pelo Prof. Dr. Luís Silva, pelo ISEP. O trabalho foi dividido em duas partes, sendo a primeira direcionada à obtenção do novo crude a partir de dois crudes pesados e caracterização dessa mistura. Já a segunda parte reside na refinação deste novo crude através da plataforma Aspen Plus para obtenção do resíduo de vácuo, para posterior processamento na coluna de discos rotativos usando um método de separação por extração liquido-liquido. Estudaram-se as propriedades físicas dos fluidos e verificou-se que na destilação atmosférica as curvas de destilação encontram-se muito próximas comparativamente com os resultados obtidos pela empresa, enquanto na destilação a vácuo os valores encontram-se mais afastados, apresentando uma variação de 30ºC a 100ºC em relação aos valores obtidos pelo Petro-Sim. Com a finalidade de cumprir um dos objetivos em falta, irão ser realizadas futuramente simulações no extrator de discos rotativos para otimização do processo para crudes pesados, sendo os resultados facultados, posteriormente, à Petrogal. Durante a realização do trabalho foi atingido um modelo real representativo da unidade de destilação atmosférica e a vácuo da Petrogal, podendo obter-se resultados para qualquer tipo de crude, fazendo apenas variar o assay da corrente de alimentação.

Square-wave voltametric method for determination of molinate concentration in a biological process using a hanging mercury drop electrode

A square-wave voltammetric (SWV) method using a hanging mercury drop electrode (HMDE) has been developed for determination of the herbicide molinate in a biodegradation process. The method is based on controlled adsorptive accumulation of molinate for 10 s at a potential of -0.8 V versus AgCl/Ag. An anodic peak, due to oxidation of the adsorbed pesticide, was observed in the cyclic voltammogram at ca. -0.320 V versus AgCl/Ag; a very small cathodic peak was also detected. The SWV calibration plot was established to be linear in the range 5.0x10-6 to 9.0x10-6 mol L-1; this corresponded to a detection limit of 3.5x10-8 mol L-1. This electroanalytical method was used to monitor the decrease of molinate concentration in river waters along a biodegradation process using a bacterial mixed culture. The results achieved with this voltammetric method were compared with those obtained by use of a chromatographic method (HPLC–UV) and no significant statistical differences were observed.

Electrochemical study of butylate: application to the analysis of water

The electroactivity of butylate (BTL) is studied by cyclic voltammetry (CV) and square wave voltammetry (SWV) at a glassy carbon electrode (GCE) and a hanging mercury drop electrode (HMDE). Britton–Robinson buffer solutions of pH 1.9–11.5 are used as supporting electrolyte. CV voltammograms using GCE show a single anodic peak regarding the oxidation of BTL at +1.7V versus AgCl/ Ag, an irreversible process controlled by diffusion. Using a HMDE, a single cathodic peak is observed, at 1.0V versus AgCl/Ag. The reduction of BTL is irreversible and controlled by adsorption. Mechanism proposals are presented for these redox transformations. Optimisation is carried out univaryingly. Linearity ranges were 0.10–0.50 mmol L-1 and 2.0–9.0 µmolL-1 for anodic and cathodic peaks, respectively. The proposed method is applied to the determination of BTL in waters. Analytical results compare well with those obtained by an HPLC method.

Direct electroanalytical determination of fluvastatin in a pharmaceutical dosage form: batch and flow analysis

The reduction of luvastatin (FLV) at a hanging mercury-drop electrode (HMDE) was studied by square-wave adsorptive-stripping voltammetry (SWAdSV). FLV can be accumulated and reduced at the electrode, with a maximum peak current intensity at a potential of approximately 1.26V vs. AgCl=Ag, in an aqueous electrolyte solution of pH 5.25. The method shows linearity between peak current intensity and FLV concentration between 1.0 10 8 and 2.7 10 6 mol L 1. Limits of detection (LOD) and quantification (LOQ) were found to be 9.9 10 9 mol L 1 and 3.3 10 8 mol L 1, respectively. Furthermore, FLV oxidation at a glassy carbon electrode surface was used for its hydrodynamic monitoring by amperometric detection in a flow-injection system. The amperometric signal was linear with FLV concentration over the range 1.0 10 6 to 1.0 10 5 mol L 1, with an LOD of 2.4 10 7 mol L 1 and an LOQ of 8.0 10 7 mol L 1. A sample rate of 50 injections per hour was achieved. Both methods were validated and showed to be precise and accurate, being satisfactorily applied to the determination of FLV in a commercial pharmaceutical.

Determination of chlorfenvinphos in soils by microwave-assisted extraction and stripping voltammetry with an ultramicroelectrode

A methodology for the determination of the pesticide chlorfenvinphos by microwave-assisted solvent extraction and square-wave cathodic stripping voltammetry at a mercury film ultramicroelectrode in soil samples is proposed. Optimization of microwave solvent extraction performed with two soils, selected for having significantly different properties, indicated that the optimum solvent for extracting chlorfenvinphos is hexane-acetone (1:1, v/v). The voltammetric procedure is based on controlled adsorptive accumulation of the insecticide at the potential of -0.60 V (vs. Ag/AgCl) in the presence of Britton-Robinson buffer (pH 6.2). The detection limit obtained for a 10 s collection time was 3.0 x 10-8 mol l-1. The validity of the developed methodology was assessed by recovery experiments at the 0.100 µg g-1 level. The average recoveries and standard deviations for the global procedure reached byMASE-square-wave voltammetry were 90.2±2.8% and 92.1±3.4% for type I (soil rich in organic matter) and type II (sandy soil) samples, respectively. These results are in accordance to the expected values which show that the method has a good accuracy.

Electrochemical determination of citalopram by adsorptive stripping voltammetry–determination in pharmaceutical products

The electrochemical behavior of citalopram was studied by square-wave and square-wave adsorptive-stripping voltammetry (SWAdSV). Citalopram can be reduced and accumulated at a mercury drop electrode, with a maximum peak current intensity being obtained at a potential of approximately -1.25V vs. AgCl/Ag, in an aqueous electrolyte solution of pH 12. A SWAdSV method has been developed for the determination of citalopram in pharmaceutical preparations. The method shows a linear range between 1.0x10-7 and 2.0x10-6 mol L-1 with a limit of detection of 5x10-8 mol L-1 for an accumulation time of 30 s. The precision of the method was evaluated by assessing the repeatability and intermediate precision, achieving good relative standard deviations in all cases (≤2.3%). The proposed method was applied to the determination of citalopram in five pharmaceutical products and the results obtained are in good agreement with the labeled values.

Determination of ametryn in soils via microwave-assisted solvent extraction coupled to anodic stripping voltammetry with a gold ultramicroelectrode

An extraction-anodic adsorptive stripping voltammetric procedure using microwave-assisted solvent extraction and a gold ultramicroelectrode was developed for determining the pesticide ametryn in soil samples. The method is based on the use of acetonitrile as extraction solvent and on controlled adsorptive accumulation of the herbicide at the potential of 0.50 V (vs. Ag/AgCl) in the presence of Britton-Robinson buffer (pH 3.3). Soil sample extracts were analysed directly after drying and redissolution with the supporting electrolyte but without other pre-treatment. The limit of detection obtained for a 10 s collection time was 0.021 µg g-1. Recovery experiments for the global procedure, at the 0.500 µg g-1 level, gave satisfactory mean and standard deviation results which were comparable to those obtained by HPLC with UV detection.

Electroanalytical study of the antidepressant sertraline

Aflowinjection squarewave cathodic stripping voltammetric method has been developed for the determination of sertraline in a pharmaceutical preparation. The method shows linearity between peak current intensity and sertraline concentration for the interval between 0.20×10−6 and 1.20×10−6 mol L−1. Limits of detection and quantification were found to be 1.5×10−7 and 5.0×10−7 mol L−1, respectively. Up to 70 samples per hour can be analysed with a good precision (R.S.D. = 2.5%). The proposed method was successfully applied to the determination of sertraline in a commercial product. In the voltammetric determination of sertraline in flow, a high sample rate is obtained at reduced costs, opening the possibility to compete with the chromatographic methods generally used for this analysis.

Study of the voltammetric behaviour of metam and its application to an amperometric flow system

The electrochemical behaviour of the pesticide metam (MT) at a glassy carbon working electrode (GCE) and at a hanging mercury drop electrode (HMDE) was investigated. Different voltammetric techniques, including cyclic voltammetry (CV) and square wave voltammetry (SWV), were used. An anodic peak (independent of pH) at +1.46 V vs AgCl/Ag was observed in MTaqueous solution using the GCE. SWV calibration curves were plotted under optimized conditions (pH 2.5 and frequency 50 Hz), which showed a linear response for 17–29 mg L−1. Electrochemical reduction was also explored, using the HMDE. A well defined cathodic peak was recorded at −0.72 V vs AgCl/ Ag, dependent on pH. After optimizing the operating conditions (pH 10.1, frequency 150 Hz, potential deposition −0.20 V for 10 s), calibration curves was measured in the concentration range 2.5×10−1 to 1.0 mg L−1 using SWV. The electrochemical behaviour of this compound facilitated the development of a flow injection analysis (FIA) system with amperometric detection for the quantification of MT in commercial formulations and spiked water samples. An assessment of the optimal FIA conditions indicated that the best analytical results were obtained at a potential of +1.30 V, an injection volume of 207 μL and an overall flow rate of 2.4 ml min−1. Real samples were analysed via calibration curves over the concentration range 1.3×10−2 to 1.3 mg L−1. Recoveries from the real samples (spiked waters and commercial formulations) were between 97.4 and 105.5%. The precision of the proposed method was evaluated by assessing the relative standard deviation (RSD %) of ten consecutive determinations of one sample (1.0 mg L−1), and the value obtained was 1.5%.

Electroanalytical study of the pesticide ethiofencarb

A detailed study of voltammetric behavior of ethiofencarb (ETF) is reported using glassy carbon electrode (GCE) and hanging mercury drop electrode (HMDE). With GCE, it is possible to verify that the oxidative mechanism is irreversible, independent of pH, and the maximum intensity current was observed at +1.20 V vs. AgCl/Ag at pH 1.9. A linear calibration line was obtained from 1.0x10-4 to 8.0x10-4 mol L-1 with SWV method. To complete the electrochemical knowledge of ETF pesticide, the reduction was also explored with HMDE. A well-defined peak was observed at –1.00V vs. AgCl/Ag in a large range of pH with higher signal at pH 7.0. Linearity was obtained in 4.2x10-6 and 9.4x10-6 mol L-1 ETF concentration range. An immediate alkaline hydrolysis of ETF was executed, producing a phenolic compound (2-ethylthiomethylphenol) (EMP), and the electrochemical activity of the product was examined. It was deduced that it is oxidized on GCE at +0.75V vs. AgCl/Ag with a maximum peak intensity current at pH 3.2, but the compound had no reduction activity on HMDE. Using the decrease of potential peak, a flow injection analysis (FIA) system was developed connected to an amperometric detector, enabling the determination of EMP over concentration range of 1.0x10-7 and 1.0x10-5 mol L-1 at a sampling rate of 60 h-1. The results provided by FIA methodology were performed by comparison with results from high-performance liquid chromatography (HPLC) technique and demonstrated good agreement with relative deviations lower than 4%. Recovery trials were performed and the obtained values were between 98 and 104%.

Maltol determination in food by microwave assisted extraction and electrochemical detection

An electrochemical method is proposed for the determination of maltol in food. Microwave-assisted extraction procedures were developed to assist sample pre-treating steps. Experiments carried out in cyclic voltammetry showed an irreversible and adsorption controlled reduction of maltol. A cathodic peak was observed at -1.0 V for a Hanging Mercury Drop Electrode versus an AgCl/Ag (in saturated KCl), and the peak potential was pH independent. Square wave voltammetric procedures were selected to plot calibration curves. These procedures were carried out with the optimum conditions: pH 6.5; frequency 50 Hz; deposition potential 0.6 V; and deposition time 10 s. A linear behaviour was observed within 5.0 × 10-8 and 3.5 × 10-7 M. The proposed method was applied to the analysis of cakes, and results were compared with those obtained by an independent method. The voltammetric procedure was proven suitable for the analysis of cakes and provided environmental and economical advantages, including reduced toxicity and volume of effluents and decreased consumption of reagents.

Bioatividade da quinoxalina 1,4-dióxido e seus derivados

O objetivo deste estudo consiste em avaliar a atividade antimicrobiana da quinoxalina 1,4-dióxido e alguns dos seus derivados em estirpes bacterianas e leveduras. Os compostos estudados foram a quinoxalina 1,4-dióxido (QNX), 2-metilquinoxalina-1,4-dióxido (2MQNX), 2-metil-3-Benzoilquinoxalina-1,4-dióxido (2M3BenzoilQNX), 2-metil-3-benzilquinoxalina-1,4-dióxido (2M3BQNX), 2-amino-3-cianoquinoxalina-1,4-dióxido (2A3CQNX), 3-metil-2-quinoxalinacarboxamida-1,4-dióxido (3M2QNXC), 2-hidroxifenazina–N-dióxido (2HF) e 3-metil-N-(2-metilphenil)quinoxalinacarboxamida-1,4-dioxido (3MN(2MF)QNXC). Os modelos procariotas selecionados para este estudo foram o Staphylococcus aureus ATCC 6538, Staphylococcus aureus ATCC 6538P, Staphylococcus aureus ATCC 29213, Escherichia coli ATCC 25922, Escherichia coli S3R9, Escherichia coli S3R22, Escherichia coli TEM CTX-M9, Escherichia coli TEM-1, Escherichia coli AmpC MOX-2, Escherichia coli CTX-M2 e Escherichia coli CTX-M9. A Candida albicans ATCC 10231 e a Saccharomyces cerevisiae PYCC 4072 constituíram os modelos eucariotas deste estudo. Para os compostos químicos que apresentem atividade pelo método de difusão em disco, será determinada a Concentração Mínima Inibitória (CMI), bem como a viabilidade e o crescimento (na presença e na ausência dos compostos químicos). Os resultados deste estudo mostram atividade antimicrobiana para a maioria dos compostos estudados em todos os modelos procariotas Gram negativos, à exceção da E.coli CTX-M2 e CTX-M9 e nenhuma atividade nos modelos eucariotas. O estudo da viabilidade/curvas de morte em bactérias e num modelo eucariota (S.cerevisiae) sugerem que alguns destes compostos constituem potenciais drogas para a quimioterapia antibacteriana.

Prevalência de resistência a antimicrobianos em isolados ambientais de Escherichia coli e enterococos

A água é um recurso escasso e indispensável à vida, podendo ser um importante veículo de microrganismos patogénicos com origem fecal. A matéria fecal é também uma fonte de microrganismos resistentes a antimicrobianos e contribui para a sua disseminação e dos seus genes de resistência no ambiente e entre as comunidades microbianas comensais e microrganismos patogénicos humanos e animais. A qualidade microbiológica da água é monitorizada recorrendo à utilização de bioindicadores como Escherichia coli, enterococos e microrganismos totais. O presente estudo apresentou como principal objetivo determinar a prevalência de ESBLs e AmpCs e ainda avaliar a prevalência de estirpes de enterococos com resistência à vancomicina (VRE) em águas do rio Douro e da orla costeira da cidade do Porto. As amostragens de água foram realizadas em quatro locais localizados no estuário do rio Douro e orla costeira da cidade do Porto entre o mês de Abril e Julho. A deteção e quantificação dos bioindicadores foram realizadas pelo método de filtração por membrana. A suscetibilidade das estirpes de E. coli e enterococos foi testada pelo método de difusão em disco relativamente a várias classes de antimicrobianos. As contagens microbianas mais elevadas foram determinadas entre Abril e Junho e em amostras de água doce. Foram isoladas 62 estirpes de E. coli e 49 estirpes de enterococos que apresentaram prevalências de resistência a antimicrobianos de 90,3% (56/62) e 83,7% (41/49), respetivamente. As estirpes de E. coli apresentaram altas frequências de resistência à ampicilina (74,2%) e tetraciclina (61,3%). Nestas estirpes verificou-se ainda fenótipos associados a multirresistência a um mínimo de três classes de antimicrobianos em 56,5% (35/62) dos isolados. Verificou-se que as estirpes de enterococos apresentaram altos níveis de resistência à rifampicina (34,7%) e azitromicina (40,8%), detetando-se ainda a manifestação de fenótipo de resistência à vancomicina em 26,5% das estirpes. Observou-se uma prevalência de 36,7% (18/49) de estirpes de enterococos associadas a fenómenos de multirresistência antimicrobiana. Ana Martins vi Os resultados obtidos sugerem que o rio Douro e orla costeira, bem como os ambientes aquáticos, constituem reservatórios de bactérias e genes de resistência a antimicrobianos e possuem um papel preponderante na sua disseminação.

Gestão e monitorização de uma rede departamental: um caso de estudo

Mestrado em Engenharia Electrotécnica e de Computadores

Iron oxide/gold core/shell nanomagnetic probes and CdS biolabels for amplified electrochemical immunosensing of Salmonella typhimurium

There is an imminent need for rapid methods to detect and determine pathogenic bacteria in food products as alternatives to the laborious and time-consuming culture procedures. In this work, an electrochemical immunoassay using iron/gold core/shell nanoparticles (Fe@Au) conjugated with anti-Salmonella antibodies was developed. The chemical synthesis and functionalization of magnetic and gold-coated magnetic nanoparticles is reported. Fe@Au nanoparticles were functionalized with different self-assembled monolayers and characterized using ultraviolet-visible spectrometry, transmission electron microscopy, and voltammetric techniques. The determination of Salmonella typhimurium, on screen-printed carbon electrodes, was performed by square-wave anodic stripping voltammetry through the use of CdS nanocrystals. The calibration curve was established between 1×101 and 1×106 cells/mL and the limit of detection was 13 cells/mL. The developed method showed that it is possible to determine the bacteria in milk at low concentrations and is suitable for the rapid (less than 1 h) and sensitive detection of S. typhimurium in real samples. Therefore, the developed methodology could contribute to the improvement of the quality control of food samples.