Estudo comparativo do comportamento de diferentes ferramentas na fresagem de aços duplex

A maquinagem por arranque de apara é, na actualidade, um dos processos de fabrico mais utilizados e de maior relevo no panorama da indústria metalomecânica mundial. Para além da forte evolução que se tem registado ao longo das últimas décadas nos equipamentos ligados à maquinagem, também as ferramentas têm visto o seu desempenho fortemente melhorado, graças essencialmente ao desenvolvimento de revestimentos finos, mono e multicamada, que têm proporcionado o conjunto de propriedades mais indicado a cada situação. Por outro lado, os aços inoxidáveis duplex têm registado um forte incremento na sua aplicação, a qual requer, em muitos casos, o uso da maquinagem para a obtenção das formas necessárias. Tendo em consideração estes dois factores, o presente trabalho visa, essencialmente avaliar qual a ferramenta mais adequada para trabalhar este tipo de ligas, em função do tipo de maquinagem e condições de corte. Para tal, foram utilizadas diferentes ferramentas dotadas da mesma geometria, e seleccionados parâmetros que constituíssem um denominador comum entre os valores indicados pelos diferentes fabricantes. Foram consideradas apenas condições de maquinagem com utilização de fluido de corte e realizados percursos de corte previamente determinados na fresagem, utilizando fresas de topo em condições de maquinagem de alta velocidade. A análise comparativa recaiu sobre a qualidade da superfície gerada por maquinagem, avaliada através de perfilometria, e o desgaste registado por cada uma das ferramentas utilizadas.

Cutting forces and wear analysis of Si3N4 diamond coated tools in high speed machining

Si3N4 tools were coated with a thin diamond film using a Hot-Filament Chemical Vapour Deposition (HFCVD) reactor, in order to machining a grey cast iron. Wear behaviour of these tools in high speed machining was the main subject of this work. Turning tests were performed with a combination of cutting speeds of 500, 700 and 900 m min−1, and feed rates of 0.1, 0.25 and 0.4 mm rot−1, remaining constant the depth of cut of 1 mm. In order to evaluate the tool behaviour during the turning tests, cutting forces were analyzed being verified a significant increase with feed rate. Diamond film removal occurred for the most severe set of cutting parameters. It was also observed the adhesion of iron and manganese from the workpiece to the tool. Tests were performed on a CNC lathe provided with a 3-axis dynamometer. Results were collected and registered by homemade software. Tool wear analysis was achieved by a Scanning Electron Microscope (SEM) provided with an X-ray Energy Dispersive Spectroscopy (EDS) system. Surface analysis was performed by a profilometer.

Scheduling a cutting and treatment stainless steel sheet line with self-management capabilities

With advancement in computer science and information technology, computing systems are becoming increasingly more complex with an increasing number of heterogeneous components. They are thus becoming more difficult to monitor, manage, and maintain. This process has been well known as labor intensive and error prone. In addition, traditional approaches for system management are difficult to keep up with the rapidly changing environments. There is a need for automatic and efficient approaches to monitor and manage complex computing systems. In this paper, we propose an innovative framework for scheduling system management by combining Autonomic Computing (AC) paradigm, Multi-Agent Systems (MAS) and Nature Inspired Optimization Techniques (NIT). Additionally, we consider the resolution of realistic problems. The scheduling of a Cutting and Treatment Stainless Steel Sheet Line will be evaluated. Results show that proposed approach has advantages when compared with other scheduling systems

Evaluation of tools and cutting conditions on carbon fibre reinforced laminates

The distinctive characteristics of carbon fibre reinforced plastics, like low weight or high specific strength, had broadened their use to new fields. Due to the need of assembly to structures, machining operations like drilling are frequent. In result of composites inhomogeneity, this operation can lead to different damages that reduce mechanical strength of the parts in the connection area. From these damages, delamination is the most severe. A proper choice of tool and cutting parameters can reduce delamination substantially. In this work the results obtained with five different tool geometries are compared. Conclusions show that the choice of an adequate drill can reduce thrust forces, thus delamination damage.

Provably Good Task Assignment for Two-Type Heterogeneous Multiprocessors Using Cutting Planes

Consider scheduling of real-time tasks on a multiprocessor where migration is forbidden. Specifically, consider the problem of determining a task-to-processor assignment for a given collection of implicit-deadline sporadic tasks upon a multiprocessor platform in which there are two distinct types of processors. For this problem, we propose a new algorithm, LPC (task assignment based on solving a Linear Program with Cutting planes). The algorithm offers the following guarantee: for a given task set and a platform, if there exists a feasible task-to-processor assignment, then LPC succeeds in finding such a feasible task-to-processor assignment as well but on a platform in which each processor is 1.5 × faster and has three additional processors. For systems with a large number of processors, LPC has a better approximation ratio than state-of-the-art algorithms. To the best of our knowledge, this is the first work that develops a provably good real-time task assignment algorithm using cutting planes.

An integer programming framework for sequencing cutting patterns based on interval graph completion

We derived a framework in integer programming, based on the properties of a linear ordering of the vertices in interval graphs, that acts as an edge completion model for obtaining interval graphs. This model can be applied to problems of sequencing cutting patterns, namely the minimization of open stacks problem (MOSP). By making small modifications in the objective function and using only some of the inequalities, the MOSP model is applied to another pattern sequencing problem that aims to minimize, not only the number of stacks, but also the order spread (the minimization of the stack occupation problem), and the model is tested.

Sequencing cutting patterns with colored interval graphs

The problem addressed here originates in the industry of flat glass cutting and wood panel sawing, where smaller items are cut from larger items accordingly to predefined cutting patterns. In this type of industry the smaller pieces that are cut from the patterns are piled around the machine in stacks according to the size of the pieces, which are moved to the warehouse only when all items of the same size have been cut. If the cutting machine can process only one pattern at a time, and the workspace is limited, it is desirable to set the sequence in which the cutting patterns are processed in a way to minimize the maximum number of open stacks around the machine. This problem is known in literature as the minimization of open stacks (MOSP). To find the best sequence of the cutting patterns, we propose an integer programming model, based on interval graphs, that searches for an appropriate edge completion of the given graph of the problem, while defining a suitable coloring of its vertices.

Simulação de sistema de desenfumagem de parques de estacionamento recorrendo ao programa OpenFOAM

Os parques de estacionamento cobertos estão obrigados por legislação a terem sistemas de desenfumagem. Assim, nesta dissertação desenvolve-se um procedimento computacional para a analise e verificação de funcionamento de sistemas de desenfumagem com ventiladores de impulso para parques de estacionamento, recorrendo ao software de mecânica dos fluidos computacional OpenFOAM. Actualmente nos sistemas de desenfumagem de parques de estacionamento estão a ser aplicados ventiladores de impulso. Este tipo de ventiladores não estão contemplados pela legislação em vigor. Assim, para serem utilizados é necessário verificar se estes podem substituir as redes de condutas. A verificação do funcionamento de sistemas de desenfumagem com ventiladores de impulso e efectuada com recurso a programas de simulação de mecânica dos fluidos computacional. O software OpenFOAM não tem tutoriais para ventiladores de impulso. Assim, foi executado um procedimento para validação dos ventiladores de impulso. A validação consistiu em reproduzir-se uma experiência executada por Giesen et al. (2011). Executaram-se várias simulações com diferentes modelos de turbulência, verificando-se que o programa buoyantpimplefoam do software OpenFOAM ao utilizar o modelo de turbulência k -ɛ simulou quase na perfeição os ventiladores de impulso. O desenvolvimento do procedimento computacional foi executado para um parque de estacionamento com uma geometria bastante complexa. O parque de estacionamento foi criado com um software em 3D e posteriormente inserido numa malha j a criada com as dimensões exteriores do parque. Foram estipuladas as condições de fronteira e executou-se uma simulação de seiscentos segundos com parâmetros determinados previamente. O processamento da simulação teve a duração de aproximadamente oito dias. Dos resultados obtidos concluiu-se que o procedimento computacional apresentado simula adequadamente sistemas de desenfumagem em parques de estacionamento.

Distributed Sensing of Fluid Dynamic Phenomena with the XDense Sensor Grid Network

IEEE International Conference on Cyber Physical Systems, Networks and Applications (CPSNA'15), Hong Kong, China.

Water jet based autonomous surface vehicle for coastal waters operations

This paper presents the design of low cost, small autonomous surface vehicle for missions in the coastal waters and specifically for the challenging surf zone. The main objective of the vehicle design described in this paper is to address both the capability of operation at sea in relative challenging conditions and maintain a very low set of operational requirements (ease of deployment). This vehicle provides a first step towards being able to perform general purpose missions (such as data gathering or patrolling) and to at least in a relatively short distances to be able to be used in rescue operations (with very low handling requirements) such as carrying support to humans on the water. The USV is based on a commercially available fiber glass hull, it uses a directional waterjet powered by an electrical brushless motor for propulsion, thus without any protruding propeller reducing danger in rescue operations. Its small dimensions (1.5 m length) and weight allow versatility and ease of deployment. The vehicle design is described in this paper both from a hardware and software point of view. A characterization of the vehicle in terms of energy consumption and performance is provided both from test tank and operational scenario tests. An example application in search and rescue is also presented and discussed with the integration of this vehicle in the European ICARUS (7th framework) research project addressing the development and integration of robotic tools for large scale search and rescue operations.

Cutting path as a rural postman problem

The Rural Postman Problem (RPP) is a particular Arc Routing Problem (ARP) which consists of determining a minimum cost circuit on a graph so that a given subset of required edges is traversed. The RPP is an NP-hard problem with significant real-life applications. This paper introduces an original approach based on Memetic Algorithms - the MARP algorithm - to solve the RPP and, also deals with an interesting Industrial Application, which focuses on the path optimization for component cutting operations. Memetic Algorithms are a class of Metaheuristics which may be seen as a population strategy that involves cooperation and competition processes between population elements and integrates “social knowledge”, using a local search procedure. The MARP algorithm is tested with different groups of instances and the results are compared with those gathered from other publications. MARP is also used in the context of various real-life applications.

Projeto da estrutura e sistema de movimentação robotizado de linha automática de corte de chapa

Os robots de movimentação de chapa são bastantes úteis para as empresas de metalomecânica. De facto, cada vez mais existem máquinas de corte por jato de água, laser ou outros processos, nos quais os robots apresentam um papel importante na carga e descarga do material. O trabalho realizado apresenta novas soluções aos sistemas de movimentação existentes no mercado, e permite reduzir os custos na movimentação do material. Este projeto serve essencialmente para chapas em trajetória retilínea, e efetuar o seu levantamento do equipamento e deposição em estrutura de suporte (ou viceversa). A vantagem a ter em conta é a diminuição dos custos de movimentação do material. Neste trabalho apresentou-se a metodologia de dimensionamento de um robot automatizado que transporta chapas com um peso máximo de 3500 kg, tendo por base as normas do EC3-P1.8 e o Método de Elementos Finitos (MEF). No decurso do projeto foram abordadas os seguintes temas: Abordagem inicial da geometria através do Solidworks; Dimensionamento da estrutura por software de Elementos Finitos, o Solidworks; Dimensionamento das correntes, carretos/discos ou coroas e rolamentos; Dimensionamento e seleção dos moto-redutores, bomba de vácuo e ventosas; Cálculo das solicitações em cada membro da estrutura por software de análise estrutural, o Multiframe3D, e respetivo dimensionamento das ligações aparafusadas e soldadas; Elaboração dos desenhos de projeto finais, processos de fabrico e custos; Dimensionamento do acionamento, MG e disposição dos dispositivos no quadro elétrico. Como conclusão refere-se que se conseguiu realizar o projeto e obter uma solução final otimizada, com a ajuda de ferramentas importantes, como sejam o MEF, resultando num equipamento cujas solicitações para a estrutura e sistema de movimentação foram otimizadas, resultando num equipamento eficiente, robusto, seguro e de custo reduzido.

Kitchen robot prod. line development. Proj. of Bowden cables cutting and thermal forming machine.

This document presents particular description of work done during student’s internship in PR Metal company realized as ERASMUS PROJECT at ISEP. All information including company’s description and its structure, overview of the problems and analyzed cases, all stages of projects from concept to conclusion can be found here. Description of work done during the internship is divided here into two pieces. First part concerns one activities of the company which is robotic chefs (kitchen robot) production line. Work, that was done for development of this line involved several tasks, among them: creating a single-worker montage station for screwing robots housing’s parts, improve security system for laser welding chamber, what particularly consists in designing automatically closing door system with special surface, that protects against destructive action of laser beam, test station for examination of durability of heating connectors, solving problem with rotors vibrations. Second part tells about main task, realized in second half of internship and stands a complete description of machine development and design. The machine is a part of car handle latch cable production line and its tasks are: cutting cable to required length and hot-forming plastic cover for further assembly needs.