Practical Quality Control: Comparision of Methods on the Quantification of Stationary Phases in Paper and Thin-Layer Chromatographic Systems

Introduction: Paper and thin layer chromatography methods are frequently used in Classic Nuclear Medicine for the determination of radiochemical purity (RCP) on radiopharmaceutical preparations. An aliquot of the radiopharmaceutical to be tested is spotted at the origin of a chromatographic strip (stationary phase), which in turn is placed in a chromatographic chamber in order to separate and quantify radiochemical species present in the radiopharmaceutical preparation. There are several methods for the RCP measurement, based on the use of equipment as dose calibrators, well scintillation counters, radiochromatografic scanners and gamma cameras. The purpose of this study was to compare these quantification methods for the determination of RCP. Material and Methods: 99mTc-Tetrofosmin and 99mTc-HDP are the radiopharmaceuticals chosen to serve as the basis for this study. For the determination of RCP of 99mTc-Tetrofosmin we used ITLC-SG (2.5 x 10 cm) and 2-butanone (99mTc-tetrofosmin Rf = 0.55, 99mTcO4- Rf = 1.0, other labeled impurities 99mTc-RH RF = 0.0). For the determination of RCP of 99mTc-HDP, Whatman 31ET and acetone was used (99mTc-HDP Rf = 0.0, 99mTcO4- Rf = 1.0, other labeled impurities RF = 0.0). After the development of the solvent front, the strips were allowed to dry and then imaged on the gamma camera (256x256 matrix; zoom 2; LEHR parallel-hole collimator; 5-minute image) and on the radiochromatogram scanner. Then, strips were cut in Rf 0.8 in the case of 99mTc-tetrofosmin and Rf 0.5 in the case of 99mTc-HDP. The resultant pieces were smashed in an assay tube (to minimize the effect of counting geometry) and counted in the dose calibrator and in the well scintillation counter (during 1 minute). The RCP was calculated using the formula: % 99mTc-Complex = [(99mTc-Complex) / (Total amount of 99mTc-labeled species)] x 100. Statistical analysis was done using the test of hypotheses for the difference between means in independent samples. Results:The gamma camera based method demonstrated higher operator-dependency (especially concerning the drawing of the ROIs) and the measures obtained using the dose calibrator are very sensitive to the amount of activity spotted in the chromatographic strip, so the use of a minimum of 3.7 MBq activity is essential to minimize quantification errors. Radiochromatographic scanner and well scintillation counter showed concordant results and demonstrated the higher level of precision. Conclusions: Radiochromatographic scanners and well scintillation counters based methods demonstrate to be the most accurate and less operator-dependant methods.

Comparative study between two distinct methods for attenuation correction and the use of no-attenuation correction for the assessment of relative uptake of 99mTc-DMSA on pediatric patients

Introduction: Although relative uptake values aren’t the most important objective of a 99mTc-DMSA scan, they are important quantitative information. In most of the dynamic renal scintigraphies attenuation correction is essential if one wants to obtain a reliable result of the quantification process. Although in DMSA scans the absent of significant background and the lesser attenuation in pediatric patients, makes that this attenuation correction techniques are actually not applied. The geometric mean is the most common method, but that includes the acquisition of an anterior (extra) projection, which it is not acquired by a large number of NM departments. This method and the attenuation factors proposed by Tonnesen will be correlated with the absence of attenuation correction procedures. Material and Methods: Images from 20 individuals (aged 3 years +/- 2) were used and the two attenuation correction methods applied. The mean time of acquisition (time post DMSA administration) was 3.5 hours +/- 0.8h. Results: The absence of attenuation correction showed a good correlation with both attenuation methods (r=0.73 +/- 0.11) and the mean difference verified on the uptake values between the different methods were 4 +/- 3. The correlation was higher when the age was lower. The attenuation correction methods correlation was higher between them two than with the “no attenuation correction” method (r=0.82 +/- 0.8), and the mean differences of the uptake values were 2 +/- 2. Conclusion: The decision of not doing any kind of attenuation correction method can be justified by the minor differences verified on the relative kidney uptake values. Nevertheless, if it is recognized that there is a need for an accurate value of the relative kidney uptake, then an attenuation correction method should be used. Attenuation correction factors proposed by Tonnesen can be easily implemented and so become a practical and easy to implement alternative, namely when the anterior projection - needed for the geometric mean methodology – is not acquired.

Avaliação da participação em crianças e jovens com paralisia cerebral, na ilha de S. Miguel, Açores

Introdução: Nas crianças/jovens com Paralisia Cerebral (PC), as limitações motoras repercutem-se em limitações funcionais e, consequentemente, na diminuição da participação em ocupações. Sendo as manifestações da PC diferentes de indivíduo para indivíduo, estas vão refletir, dependendo da gravidade, quadro motor, ambiente físico e social, diferentes níveis de participação. Objetivo: O objetivo deste estudo foi avaliar a relação entre a idade, sexo e grau de comprometimento motor e a participação em crianças/jovens com diagnóstico de paralisia cerebral com idades compreendidas entre os 5 e os 18 anos na ilha de São Miguel. Amostra e Métodos: 25 crianças de ambos os sexos (5- 18 anos), sinalizadas em instituições especializadas de reabilitação e em Centros de Atividades Ocupações (CAO’s) na Ilha de São Miguel – Açores. Foram aplicados dois instrumentos de avaliação às crianças/jovens, Gross Motor Function Measure e Quality of Upper Extremity Skills Test, e foram entregues aos pais os outros dois instrumentos para autopreenchimento, Assessment of Life Habits e Child Health Questionnaire – Parent- Form 50. Na análise estatística, recorreu-se a testes como o Kolmogorov-Smirnov, Tstudent ou Mann-Whitney, teste de Fisher, teste de Spearman e ANOVA. Resultados: Não foram encontradas relações significativas entre a idade e o sexo e o nível de participação das crianças/jovens com PC. Contrariamente, ao avaliarmos a relação entre o grau de participação e o grau de afetação verificamos que esta é significativa (p=0,004). Conclusão: Na nossa amostra não se encontrou uma influência da idade e do sexo com a frequência da participação (relações não foram significativas). Contudo, pode-se concluir que as crianças/jovens que apresentam menos limitações motoras, como as que se enquadram no nível I/II da Gross Motor Function Classification System, apresentam níveis de participação maiores do que as que apresentam níveis de afetação motora maiores (Nível V)

Balanceamento de linhas de produção usando algoritmos genéticos

Aquando da definição de um layout por fluxo de produto, ou linha de produção, é necessário proceder-se à melhor selecção de combinações de tarefas a serem executadas em cada estação / posto de trabalho para que o trabalho seja executado numa sequência exequível e sejam necessárias quantidades de tempo aproximadamente iguais em cada estação / posto de trabalho. Este processo é chamado de balanceamento da linha de produção. Verifica-se que as estações de trabalho e equipamentos podem ser combinados de muitas maneiras diferentes; daí que a necessidade de efectuar o balanceamento das linhas de produção implique a distribuição de actividades sequenciais por postos de trabalho de modo a permitir uma elevada utilização de trabalho e de equipamentos e a minimizar o tempo de vazio. Os problemas de balanceamento de linhas são tipicamente problemas complexos de tratar, devido ao elevado número de combinações possíveis. Entre os métodos utilizados para resolver estes problemas encontram-se métodos de tentativa e erro, métodos heurísticos, métodos computacionais de avaliação de diferentes opções até se encontrar uma boa solução e métodos de optimização. O objectivo deste trabalho passou pelo desenvolvimento de uma ferramenta computacional para efectuar o balanceamento de linhas de produção recorrendo a algoritmos genéticos. Foi desenvolvida uma aplicação que implementa dois algoritmos genéticos, um primeiro que obtém soluções para o problema e um segundo que optimiza essas soluções, associada a uma interface gráfica em C# que permite a inserção do problema e a visualização de resultados. Obtiveram-se resultados exequíveis demonstrando vantagens em relação aos métodos heurísticos, pois é possível obter-se mais do que uma solução. Além disso, para problemas complexos torna-se mais prático o uso da aplicação desenvolvida. No entanto, esta aplicação permite no máximo seis precedências por cada operação e resultados com o máximo de nove estações de trabalho.

Agrupamento de dados visual interactivo

Com a crescente geração, armazenamento e disseminação da informação nos últimos anos, o anterior problema de falta de informação transformou-se num problema de extracção do conhecimento útil a partir da informação disponível. As representações visuais da informação abstracta têm sido utilizadas para auxiliar a interpretação os dados e para revelar padrões de outra forma escondidos. A visualização de informação procura aumentar a cognição humana aproveitando as capacidades visuais humanas, de forma a tornar perceptível a informação abstracta, fornecendo os meios necessários para que um humano possa absorver quantidades crescentes de informação, com as suas capacidades de percepção. O objectivo das técnicas de agrupamento de dados consiste na divisão de um conjunto de dados em vários grupos, em que dados semelhantes são colocados no mesmo grupo e dados dissemelhantes em grupos diferentes. Mais especificamente, o agrupamento de dados com restrições tem o intuito de incorporar conhecimento a priori no processo de agrupamento de dados, com o objectivo de aumentar a qualidade do agrupamento de dados e, simultaneamente, encontrar soluções apropriadas a tarefas e interesses específicos. Nesta dissertação é estudado a abordagem de Agrupamento de Dados Visual Interactivo que permite ao utilizador, através da interacção com uma representação visual da informação, incorporar o seu conhecimento prévio acerca do domínio de dados, de forma a influenciar o agrupamento resultante para satisfazer os seus objectivos. Esta abordagem combina e estende técnicas de visualização interactiva de informação, desenho de grafos de forças direccionadas e agrupamento de dados com restrições. Com o propósito de avaliar o desempenho de diferentes estratégias de interacção com o utilizador, são efectuados estudos comparativos utilizando conjuntos de dados sintéticos e reais.

Development of electrochemical methods for determination of tramadol - analytical application to pharmaceutical dosage forms

A square-wave voltammetric (SWV) method and a flow injection analysis system with amperometric detection were developed for the determination of tramadol hydrochloride. The SWV method enables the determination of tramadol over the concentration range of 15-75 µM with a detection limit of 2.2 µM. Tramadol could be determined in concentrations between 9 and 50 µM at a sampling rate of 90 h-1, with a detection limit of 1.7 µM using the flow injection system. The electrochemical methods developed were successfully applied to the determination of tramadol in pharmaceutical dosage forms, without any pre-treatment of the samples. Recovery trials were performed to assess the accuracy of the results; the values were between 97 and 102% for both methods.

Determination of pesticides in fruit and fruit juices by chromatographic methods. An overview

In order to combat a variety of pests, pesticides are widely used in fruits. Several extraction procedures (liquid extraction, single drop microextraction, microwave-assisted extraction, pressurized liquid extraction, supercritical fluid extraction, solid-phase extraction, solid-phase microextraction, matrix solid-phase dispersion, and stir bar sorptive extraction) have been reported to determine pesticide residues in fruits and fruit juices. The significant change in recent years is the introduction of the Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) methods in these matrices analysis. A combination of techniques reported the use of new extraction methods and chromatography to provide better quantitative recoveries at low levels. The use of mass spectrometric detectors in combination with liquid and gas chromatography has played a vital role to solve many problems related to food safety. The main attention in this review is on the achievements that have been possible because of the progress in extraction methods and the latest advances and novelties in mass spectrometry, and how these progresses have influenced the best control of food, allowing for an increase in the food safety and quality standards.

Electrochemical methods in pesticides control

The state of the art of voltammetric and amperometric methods used in the study and determination of pesticides in crops, food, phytopharmaceutical products, and environmental samples is reviewed. The main structural groups of pesticides, i.e., triazines, organophosphates, organochlorides, nitrocompounds, carbamates, thiocarbamates, sulfonylureas, and bipyridinium compounds are considered with some degradation products. The advantages, drawbacks, and trends in the development of voltammetric and amperometric methods for study and determination of pesticides in these samples are discussed.

Methodology for in-game certification in serious games

Serious games are starting to attain a higher role as tools for learning in various contexts, but in particular in areas such as education and training. Due to its characteristics, such as rules, behavior simulation and feedback to the player's actions, serious games provide a favorable learning environment where errors can occur without real life penalty and students get instant feedback from challenges. These challenges are in accordance with the intended objectives and will self-adapt and repeat according to the student’s difficulty level. Through motivating and engaging environments, which serve as base for problem solving and simulation of different situations and contexts, serious games have a great potential to aid players developing professional skills. But, how do we certify the acquired knowledge and skills? With this work we intend to propose a methodology to establish a relationship between the game mechanics of serious games and an array of competences for certification, evaluating the applicability of various aspects in the design and development of games such as the user interfaces and the gameplay, obtaining learning outcomes within the game itself. Through the definition of game mechanics combined with the necessary pedagogical elements, the game will ensure the certification. This paper will present a matrix of generic skills, based on the European Framework of Qualifications, and the definition of the game mechanics necessary for certification on tour guide training context. The certification matrix has as reference axes: skills, knowledge and competencies, which describe what the students should learn, understand and be able to do after they complete the learning process. The guides-interpreters welcome and accompany tourists on trips and visits to places of tourist interest and cultural heritage such as museums, palaces and national monuments, where they provide various information. Tour guide certification requirements include skills and specific knowledge about foreign languages and in the areas of History, Ethnology, Politics, Religion, Geography and Art of the territory where it is inserted. These skills are communication, interpersonal relationships, motivation, organization and management. This certification process aims to validate the skills to plan and conduct guided tours on the territory, demonstrate knowledge appropriate to the context and finally match a good group leader. After defining which competences are to be certified, the next step is to delineate the expected learning outcomes, as well as identify the game mechanics associated with it. The game mechanics, as methods invoked by agents for interaction with the game world, in combination with game elements/objects allows multiple paths through which to explore the game environment and its educational process. Mechanics as achievements, appointments, progression, reward schedules or status, describe how game can be designed to affect players in unprecedented ways. In order for the game to be able to certify tour guides, the design of the training game will incorporate a set of theoretical and practical tasks to acquire skills and knowledge of various transversal themes. For this end, patterns of skills and abilities in acquiring different knowledge will be identified.

Estudo da implementação da filosofia Lean na indústria Portuguesa

A forte competitividade dos mercados a nível nacional e internacional tem levado muitas empresas a estudar métodos e técnicas de incremento à eliminação dos desperdícios, à redução de custos e tempos, ao aumento da qualidade e da flexibilidade, tendo a filosofia lean um papel crucial na prossecução destes objectivos. Desde os seus primórdios, a avaliação da implementação da filosofia lean no universo das empresas é uma questão de investigação na área de conhecimento da gestão industrial. Embora a nível individual as diferentes empresas possam quantificar e avaliar os resultados da aplicação do lean, a grande dificuldade surge quando se pretende obter uma comparação por sector ou tipo de actividade económica. Existem países onde a prática do lean tem sido prioritária e as empresas ocupam a vanguarda nesta área de conhecimento. No entanto, em Portugal, existe uma clara dificuldade em se determinar até que ponto o tecido empresarial português assimilou esta filosofia e que resultados têm obtido com a prática do lean. Este trabalho apresenta um estudo realizado a partir de um inquérito, obtido através de um questionário on-line, às empresas que operam em Portugal de forma a estudar e analisar o estado actual do lean em Portugal e antever tendências futuras numa perspectiva de evolução da aplicação desta metodologia de gestão de processos produtivos. Em resultado deste estudo foi possível identificar quais são os grandes obstáculos à introdução do lean, áreas em que se observou sucesso ou menor impacto e quais as ferramentas e técnicas mais usadas por sector. Como resultado deste estudo é convicção do autor que foi possível obter uma fotografia abrangente do actual estado de implementação do lean e desta forma caracterizar as áreas que seguem na vanguarda da implementação do lean, e as áreas que ainda apresentam um desenvolvimento incipiente. Desta forma parece ao autor que o presente estudo apresenta grande utilidade para o mundo académico bem como para o tecido empresarial português.

Local fractional variational iteration and decomposition methods for wave equation on cantor sets within local fractional operators

We perform a comparison between the fractional iteration and decomposition methods applied to the wave equation on Cantor set. The operators are taken in the local sense. The results illustrate the significant features of the two methods which are both very effective and straightforward for solving the differential equations with local fractional derivative.

Evaluating P-NET message's response time with fixed priority queuing at application process level

P-NET is a multi-master fieldbus standard based on a virtual token passing scheme. In P-NET each master is allowed to transmit only one message per token visit. In the worst-case, the communication response time can be derived considering that, in each token cycle, all stations use the token to transmit a message. In this paper, we define a more sophisticated P-NET model, which considers the actual token utilisation. We then analyse the possibility of implementing a local priority-based scheduling policy to improve the real-time behaviour of P-NET.

Evaluating the duration of message transactions in broadcast wired/wireless fieldbus networks

Determining the response time of message transactions is one of the major concerns in the design of any distributed computer-controlled system. Such response time is mainly dependent on the medium access delay, the message length and the transmission delay. While the medium access delay in fieldbus networks has been thoroughly studied in the last few years, the transmission delay has been almost ignored as it is considered that it can be neglected when compared to the length of the message itself. Nevertheless, this assumption is no longer valid when considering the case of hybrid wired/wireless fieldbus networks, where the transmission delay through a series of different mediums can be several orders of magnitude longer than the length of the message itself. In this paper, we show how to compute the duration of message transactions in hybrid wired/wireless fieldbus networks. This duration is mainly dependent on the duration of the request and response frames and on the number and type of physical mediums that the frames must cross between initiator and responder. A case study of a hybrid wired/wireless fieldbus network is also presented, where it becomes clear the interest of the proposed approach

Evaluating Android OS for embedded real-time systems

Since its official public release, Android has captured the interest from companies, developers and the general audience. From that time up to now, this software platform has been constantly improved either in terms of features or supported hardware and, at the same time, extended to new types of devices different from the originally intended mobile ones. However, there is a feature that has not been explored yet - its real-time capabilities. This paper intends to explore this gap and provide a basis for discussion on the suitability of Android in order to be used in Open Real-Time environments. By analysing the software platform, with the main focus on the virtual machine and its underlying operating system environments, we are able to point out its current limitations and, therefore, provide a hint on different perspectives of directions in order to make Android suitable for these environments. It is our position that Android may provide a suitable architecture for real-time embedded systems, but the real-time community should address its limitations in a joint effort at all of the platform layers.