Trends Of CPU, GPU and FPGA for high-performance computing

Floating-point computing with more than one TFLOP of peak performance is already a reality in recent Field-Programmable Gate Arrays (FPGA). General-Purpose Graphics Processing Units (GPGPU) and recent many-core CPUs have also taken advantage of the recent technological innovations in integrated circuit (IC) design and had also dramatically improved their peak performances. In this paper, we compare the trends of these computing architectures for high-performance computing and survey these platforms in the execution of algorithms belonging to different scientific application domains. Trends in peak performance, power consumption and sustained performances, for particular applications, show that FPGAs are increasing the gap to GPUs and many-core CPUs moving them away from high-performance computing with intensive floating-point calculations. FPGAs become competitive for custom floating-point or fixed-point representations, for smaller input sizes of certain algorithms, for combinational logic problems and parallel map-reduce problems. © 2014 Technical University of Munich (TUM).

Performance of coastal sea-defense infrastructure at El Jadida (Morocco) against tsunami threat: lessons learned from the Japanese 11 March 2011 tsunami

This paper seeks to investigate the effectiveness of sea-defense structures in preventing/reducing the tsunami overtopping as well as evaluating the resulting tsunami impact at El Jadida, Morocco. Different tsunami wave conditions are generated by considering various earthquake scenarios of magnitudes ranging from M-w = 8.0 to M-w = 8.6. These scenarios represent the main active earthquake faults in the SW Iberia margin and are consistent with two past events that generated tsunamis along the Atlantic coast of Morocco. The behavior of incident tsunami waves when interacting with coastal infrastructures is analyzed on the basis of numerical simulations of near-shore tsunami waves' propagation. Tsunami impact at the affected site is assessed through computing inundation and current velocity using a high-resolution digital terrain model that incorporates bathymetric, topographic and coastal structures data. Results, in terms of near-shore tsunami propagation snapshots, waves' interaction with coastal barriers, and spatial distributions of flow depths and speeds, are presented and discussed in light of what was observed during the 2011 Tohoku-oki tsunami. Predicted results show different levels of impact that different tsunami wave conditions could generate in the region. Existing coastal barriers around the El Jadida harbour succeeded in reflecting relatively small waves generated by some scenarios, but failed in preventing the overtopping caused by waves from others. Considering the scenario highly impacting the El Jadida coast, significant inundations are computed at the sandy beach and unprotected areas. The modeled dramatic tsunami impact in the region shows the need for additional tsunami standards not only for sea-defense structures but also for the coastal dwellings and houses to provide potential in-place evacuation.

A biosignal embedded system for physiological computing

Thesis submitted in the fulfilment of the requirements for the Degree of Master in Electronic and Telecomunications Engineering

Mobile collaborative cloudless computing

Although the computational power of mobile devices has been increasing, it is still not enough for some classes of applications. In the present, these applications delegate the computing power burden on servers located on the Internet. This model assumes an always-on Internet connectivity and implies a non-negligible latency. The thesis addresses the challenges and contributions posed to the application of a mobile collaborative computing environment concept to wireless networks. The goal is to define a reference architecture for high performance mobile applications. Current work is focused on efficient data dissemination on a highly transitive environment, suitable to many mobile applications and also to the reputation and incentive system available on this mobile collaborative computing environment. For this we are improving our already published reputation/incentive algorithm with knowledge from the usage pattern from the eduroam wireless network in the Lisbon area.

A many-core co-processor for embedded parallel computing on FPGA

Single processor architectures are unable to provide the required performance of high performance embedded systems. Parallel processing based on general-purpose processors can achieve these performances with a considerable increase of required resources. However, in many cases, simplified optimized parallel cores can be used instead of general-purpose processors achieving better performance at lower resource utilization. In this paper, we propose a configurable many-core architecture to serve as a co-processor for high-performance embedded computing on Field-Programmable Gate Arrays. The architecture consists of an array of configurable simple cores with support for floating-point operations interconnected with a configurable interconnection network. For each core it is possible to configure the size of the internal memory, the supported operations and number of interfacing ports. The architecture was tested in a ZYNQ-7020 FPGA in the execution of several parallel algorithms. The results show that the proposed many-core architecture achieves better performance than that achieved with a parallel generalpurpose processor and that up to 32 floating-point cores can be implemented in a ZYNQ-7020 SoC FPGA.

The need of performance indicators for collaborative business ecosystems

During last decades there has been a trend to build collaboration platforms as enablers for groups of enterprises to jointly provide integrated services and products. As a result, the notion of business ecosystem is getting wider acceptance. However, a critical issue that is still open, despite some efforts in this area, is the identification of adequate performance indicators to measure and motivate sustainable collaboration. This work-in-progress addresses this concern, briefly presenting the state of the art of relevant contributing areas such as, collaborative networks, business ecosystems, enterprise performance indicators, social networks analysis, and supply chains. Complementarily, through an assessment of current gaps, the research challenges are identified and an approach for further development is proposed.

Diagnostic performance of visual screening tests in the elderly

This study aimed to determine and evaluate the diagnostic accuracy of visual screening tests for detecting vision loss in elderly. This study is defined as study of diagnostic performance. The diagnostic accuracy of 5 visual tests -near convergence point, near accommodation point, stereopsis, contrast sensibility and amsler grid—was evaluated by means of the ROC method (receiver operating characteristics curves), sensitivity, specificity, positive and negative likelihood ratios (LR+/LR−). Visual acuity was used as the reference standard. A sample of 44 elderly aged 76.7 years (±9.32), who were institutionalized, was collected. The curves of contrast sensitivity and stereopsis are the most accurate (area under the curves were 0.814−p = 0.001, C.I.95%[0.653;0.975]— and 0.713−p = 0.027, C.I.95%[0,540;0,887], respectively). The scores with the best diagnostic validity for the stereopsis test were 0.605 (sensitivity 0.87, specificity 0.54; LR+ 1.89, LR−0.24) and 0.610 (sensitivity 0.81, specificity 0.54; LR+1.75, LR−0.36). The scores with higher diagnostic validity for the contrast sensibility test were 0.530 (sensitivity 0.94, specificity 0.69; LR+ 3.04, LR−0.09). The contrast sensitivity and stereopsis test's proved to be clinically useful in detecting vision loss in the elderly.

Diagnostic performance of visual screening tests in the elderly

The aging of Portuguese population is characterized by an increase of individuals aged older than 65 years. Preventable visual loss in older persons is an important public health problem. Tests used for vision screening should have a high degree of diagnostic validity confirmed by means of clinical trials. The primary aim of a screening program is the early detection of visual diseases. Between 20% and 50% of older people in the UK have undetected reduced vision and in most cases is correctable. Elderly patients do not receive a systematic eye examination unless a problem arises with their glasses or suspicion vision loss. This study aimed to determine and evaluate the diagnostic accuracy of visual screening tests for detecting vision loss in elderly. Furthermore, it pretends to define the ability to find the subjects affected with vision loss as positive and the subjects not affected with the same disease as negative. The ideal vision screening method should have high sensitivity and specificity for early detection of risk factors. It should be also low cost and easy to implement in all geographic and socioeconomic regions. Sensitivity is the ability of an examination to identify the presence of a given disease and specificity is the ability of the examination to identify the absence of a given disease. It was not an aim of this study to detect abnormalities that affect visual acuity. The aim of this study was to find out what´s the best test for the identification of any vision loss.

Analysis of constructed wetland performance for irrigation reuse

Most of the wastewater treatment systems in small rural communities of the Cova da Beira region (Portugal) consist of constructed wetlands (CW) with horizontal subsurface flow (HSSF). It is believed that those systems allow the compliance of discharge standards as well as the production of final effluents with suitability for reuse. Results obtained in a nine-month campaign in an HSSF bed pointed out that COD and TSS removal were lower than expected. A discrete sampling also showed that removal of TC, FC and HE was not enough to fulfill international irrigation goals. However, the bed had a very good response to variation of incoming nitrogen loads presenting high removal of nitrogen forms. A good correlation between mass load and mass removal rate was observed for BOD5, COD, TN, NH4-N, TP and TSS, which shows a satisfactory response of the bed to the variable incoming loads. The entrance of excessive loads of organic matter and solids contributed for the decrease of the effective volume for pollutant uptake and therefore, may have negatively influenced the treatment capability. Primary treatment should be improved in order to decrease the variation of incoming organic and solid loads and to improve the removal of COD, solids and pathogenic. The final effluent presented good physical-chemical quality to be reused for irrigation, which is the most likely application in the area.

Power converter topologies for wind energy conversion systems: Integrated modeling, control strategy and performance simulation

This paper presents new integrated model for variable-speed wind energy conversion systems, considering a more accurate dynamic of the wind turbine, rotor, generator, power converter and filter. Pulse width modulation by space vector modulation associated with sliding mode is used for controlling the power converters. Also, power factor control is introduced at the output of the power converters. Comprehensive performance simulation studies are carried out with matrix, two-level and multilevel power converter topologies in order to adequately assert the system performance. Conclusions are duly drawn.

Optimal design of piezolaminated structures using B-spline strip finite element models

A package of B-spline finite strip models is developed for the linear analysis of piezolaminated plates and shells. This package is associated to a global optimization technique in order to enhance the performance of these types of structures, subjected to various types of objective functions and/or constraints, with discrete and continuous design variables. The models considered are based on a higher-order displacement field and one can apply them to the static, free vibration and buckling analyses of laminated adaptive structures with arbitrary lay-ups, loading and boundary conditions. Genetic algorithms, with either binary or floating point encoding of design variables, were considered to find optimal locations of piezoelectric actuators as well as to determine the best voltages applied to them in order to obtain a desired structure shape. These models provide an overall economy of computing effort for static and vibration problems.

Sistemas distribuídos: serviços Grid Computing

A necessidade de poder computacional é crescente nas diversas áreas de actuação humana, tanto na indústria, como em ambientes académicos. Grid Computing permite a ligação de recursos computacionais dispersos de maneira a permitir a sua utilização mais eficaz, fornecendo aos utilizadores um acesso simplificado ao poder computacional de diversos sistemas. Os primeiros projectos de Grid Computing implicavam a ligação de máquinas paralelas ou aglomerados de alto desempenho e alto custo, disponíveis apenas em algumas instituições. Contrastando com o elevado custo dos super-computadores, os computadores pessoais e a Internet sofreram uma evolução significativa nos últimos anos. O uso de computadores dispersos em uma WAN pode representar um ambiente muito interessante para processamento de alto desempenho. Os sistemas em Grid fornecem a possibilidade de se utilizar um conjunto de computadores pessoais de modo a fornecer uma computação que utiliza recursos que de outra maneira estariam omissos. Este trabalho consiste no estudo de Grid Computing a nível de conceito e de arquitectura e numa análise ao seu estado actual hoje em dia. Como complemento foi desenvolvido um componente que permite o desenvolvimento de serviços para Grids (Grid Services) mais eficaz do que o modelo de suporte a serviços actualmente utilizado. Este componente é disponibilizado sob a forma um plug-in para a plataforma Eclipse IDE.

Durability performance of concrete made with fine recycled concrete aggregates

Fine recycled aggregates are seen as the last choice in recycling for concrete production. Many references quote their detrimental influence on the most important characteristics of concrete: compressive and tensile strength; modulus of elasticity; water absorption; shrinkage: carbonation and chloride penetration. These two last characteristics are fundamental in terms of the long-term durability of reinforced or prestressed concrete. In the experimental research carried out at IST, part of which has already been published, different concrete mixes (with increasing rates of substitution of fine natural aggregates sand - with fine recycled aggregates from crushed concrete) were prepared and tested. The results were then compared with those for a reference concrete with exactly the same composition and grading curve, but with no recycled aggregates. This paper presents the main results of this research for water absorption by immersion and capillarity, chloride penetration (by means of the chloride migration coefficient), and carbonation resistance, drawing some conclusions on the feasibility of using this type of aggregate in structural concrete, while taking into account any ensuing obvious positive environmental impact.

Modelo de especificação e controlo de execuções paralelas e distribuídas

O desenvolvimento actual de aplicações paralelas com processamento intensivo (HPC - High Performance Computing) para alojamento em computadores organizados em Cluster baseia-se muito no modelo de passagem de mensagens, do qual é de realçar os esforços de definição de standards, por exemplo, MPI - Message - Passing Interface. Por outro lado, com a generalização do paradigma de programação orientado aos objectos para ambientes distribuídos (Java RMI, .NET Remoting), existe a possibilidade de considerar que a execução de uma aplicação, de processamento paralelo e intensivo, pode ser decomposta em vários fluxos de execução paralela, em que cada fluxo é constituído por uma ou mais tarefas executadas no contexto de objectos distribuídos. Normalmente, em ambientes baseados em objectos distribuídos, a especificação, controlo e sincronização dos vários fluxos de execução paralela, é realizada de forma explicita e codificada num programa principal (hard-coded), dificultando possíveis e necessárias modificações posteriores. No entanto, existem, neste contexto, trabalhos que propõem uma abordagem de decomposição, seguindo o paradigma de workflow com interacções entre as tarefas por, entre outras, data-flow, control-flow, finite - state - machine. Este trabalho consistiu em propor e explorar um modelo de execução, sincronização e controlo de múltiplas tarefas, que permita de forma flexível desenhar aplicações de processamento intensivo, tirando partido da execução paralela de tarefas em diferentes máquinas. O modelo proposto e consequente implementação, num protótipo experimental, permite: especificar aplicações usando fluxos de execução; submeter fluxos para execução e controlar e monitorizar a execução desses fluxos. As tarefas envolvidas nos fluxos de execução podem executar-se num conjunto de recursos distribuídos. As principais características a realçar no modelo proposto, são a expansibilidade e o desacoplamento entre as diferentes componentes envolvidas na execução dos fluxos de execução. São ainda descritos casos de teste que permitiram validar o modelo e o protótipo implementado. Tendo consciência da necessidade de continuar no futuro esta linha de investigação, este trabalho é um contributo para demonstrar que o paradigma de workflow é adequado para expressar e executar, de forma paralela e distribuída, aplicações complexas de processamento intensivo.

Hábitos de sono e performance académica: estudo comparativo entre Estónia e Portugal

Actualmente, na nossa sociedade, muitas das actividades diárias têm prioridade sobre o sono. A privação do sono em estudantes tem sido documentada em variados países e o problema reside no conflito entre a necessidade física e psicológica, dos estudantes, de dormir e os seus horários. Esta privação do sono é, muitas das vezes, relacionada com a diminuição do humor e do rendimento académico. No intuito de combater estes problemas, alguns estudantes recorrem ao uso de fármacos ou substâncias com vista a melhorar a sua qualidade de vida e o seu rendimento escolar. O objectivo deste estudo é (1) avaliar a qualidade de sono dos estudantes universitários, (2) avaliar a percentagem de estudantes que consomem fármacos ou substâncias para modificar o seu sono e (3) comparar os resultados entre duas escolas de saúde, Escola Superior de Tecnologia da Saúde do Porto, Portugal (ESTSP) e a Tallinn Health Care College, Estónia (THCC).