Estudo de viabilidade de utilização de VLC em infra-estruturas ITS baseadas em semáforos rodoviários a LEDs

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia de Electrónica e Telecomunicações

Colour filtering in a-SiC : H based p-i-n-p-i-n cells: A trade-off between bias polarity and absorption regions

A large area colour imager optically addressed is presented. The colour imager consists of a thin wide band gap p-i-n a-SiC:H filtering element deposited on the top of a thick large area a-SiC:H(-p)/a-Si:H(-i)/a-SiC:H(-n) image sensor, which reveals itself an intrinsic colour filter. In order to tune the external applied voltage for full colour discrimination the photocurrent generated by a modulated red light is measured under different optical and electrical bias. Results reveal that the integrated device behaves itself as an imager and a filter giving information not only on the position where the optical image is absorbed but also on it wavelength and intensity. The amplitude and sign of the image signals are electrically tuneable. In a wide range of incident fluxes and under reverse bias, the red and blue image signals are opposite in sign and the green signal is suppressed allowing blue and red colour recognition. The green information is obtained under forward bias, where the blue signal goes down to zero and the red and green remain constant. Combining the information obtained at this two applied voltages a RGB colour image picture can be acquired without the need of the usual colour filters or pixel architecture. A numerical simulation supports the colour filter analysis.

Laser scanned photodiodes (LSPs) for image sensing

An optimized ZnO:Al/a-pin SixC1-x:H/Al configuration for the laser scanned photodiode (LSP) imaging detector is proposed and the read-out parameters improved. The effect of the sensing element structure, cell configuration and light source flux are investigated and correlated with the sensor output characteristics. Data reveals that for sensors with wide band gap doped layers an increase on the image signal optimized to the blue is achieved with a dynamic range of two orders of magnitude, a responsivity of 6 mA W-1 and a sensitivity of 17 muW cm(-2) at 530 nm. The main output characteristics such as image responsivity, resolution, linearity and dynamic range were analyzed under reverse, forward and short circuit modes. The results show that the sensor performance can be optimized in short circuit mode. A trade-off between the scan time and the required resolution is needed since the spot size limits the resolution due to the cross-talk between dark and illuminated regions leading to blurring effects.

A 5GHz1.8V Low Power CMOS Low-Noise Amplifier

Wireless local-area networks (WLANs) have been deployed as office and home communications infrastructures worldwide. The diversification of the standards, such as IEEE 802.11 series demands the design of RF front-ends. Low power consumption is one of the most important design concerns in the application of those technologies. To maintain competitive hardware costs, CMOS has been used since it is the best solution for low cost and high integration processing, allowing analog circuits to be mixed with digital ones. In the receiver chain, the low noise amplifier (LNA) is one of the most critical blocks in a transceiver design. The sensitivity is mainly determined by the LNA noise figure and gain. It interfaces with the pre-select filter and the mixer. Furthermore, since it is the first gain stage, care must be taken to provide accurate input match, low-noise figure, good linearity and a sufficient gain over a wide band of operation. Several CMOS LNAs have been reported during the last decade, showing that the most research has been done at 802.11/b and GSM standards (900-2400MHz spectrum) and more recently at 802.11/a (5GHz band). One of the more significant disadvantages of 802.11/b is that the frequency band is crowded and subject to interference from other technologies, as is 2.4GHz cordless phones and Bluetooth. As the demand for radio-frequency integrated circuits, operating at higher frequency bands, increases, the IEEE 802.11/a standard becomes a very attractive option to wireless communication system developers. This paper presents the design and implementation of a low power, low noise amplifier aimed at IEEE 802.11a for WLAN applications. It was designed to be integrated with an active balun and mixer, representing the first step toward a fully integrated monolithic WLAN receiver. All the required circuits are integrated at the same die and are powered by 1.8V supply source. Preliminary experimental results (S-parameters) are shown and promise excellent results. The LNA circuit design details are illustrated in Section 2. Spectre simulation results focused at gain, noise figure (NF) and input/output matching are presented in Section 3. Finally, conclusions and comparison with other recently reported LNAs are made in Section 4, followed by future work.

Design and optimization of na ultra wideband and compact microwave antenna for radiometric monitoring of brain temperature

We present the modeling efforts on antenna design and frequency selection to monitor brain temperature during prolonged surgery using noninvasive microwave radiometry. A tapered log-spiral antenna design is chosen for its wideband characteristics that allow higher power collection from deep brain. Parametric analysis with the software HFSS is used to optimize antenna performance for deep brain temperature sensing. Radiometric antenna efficiency (eta) is evaluated in terms of the ratio of power collected from brain to total power received by the antenna. Anatomical information extracted from several adult computed tomography scans is used to establish design parameters for constructing an accurate layered 3-D tissue phantom. This head phantom includes separate brain and scalp regions, with tissue equivalent liquids circulating at independent temperatures on either side of an intact skull. The optimized frequency band is 1.1-1.6 GHz producing an average antenna efficiency of 50.3% from a two turn log-spiral antenna. The entire sensor package is contained in a lightweight and low-profile 2.8 cm diameter by 1.5 cm high assembly that can be held in place over the skin with an electromagnetic interference shielding adhesive patch. The calculated radiometric equivalent brain temperature tracks within 0.4 degrees C of the measured brain phantom temperature when the brain phantom is lowered 10. C and then returned to the original temperature (37 degrees C) over a 4.6-h experiment. The numerical and experimental results demonstrate that the optimized 2.5-cm log-spiral antenna is well suited for the noninvasive radiometric sensing of deep brain temperature.

Fraccionamento do efluente da indústria da cortiça por ultra-nanofiltração: caracterização e estudo da sua biodegradabilidade

O efluente da Indústria da Cortiça apresenta elevados teores de carga orgânica e de compostos fenólicos, nomeadamente teninos, com baixa biodegradabilidade e significativa toxicidade, o que dificulta o seu tratamento. O objectivo deste trabalho é o estudo da biodegradabilidade de diferentes fracções do efluente da cortiça, na perspectiva de contribuir para viabilizar o seu tratamento. Biológico, em simultâneo com a sua valorização, pela recuperação do seu conteúdo em taninos. O fraccionamento foi realizado através de processos de separação por membranas, nomeadamente por ultrafiltração e nanofiltração, de Limite de Exclusão Molecular (MWCO) compreendido entre 0,125-91kDa. O efluente e as fracções permeadas obtidas foram analisadas em termos de conteúdo orgânico (COT, CBO, CQO), fenóis, taninos, cor, pH e condutividade. A caracterização do efluente revelou um elevado conteúdo orgânico (2285-2604 mg de CQO/L, 670,5-1056,8 mg C/L, 1000-1225 mg CBO/L), biodegradabilidade relativamente baixa (0,44-0,47 para CBO/CQO; k de 0,25-0,24 d-1) e elevado conteúdo de fenóis (0,36-0,41 g de ácido tânico/L) e de taninos (0,25-0,27 g ácido tânico/L). O fraccionamento do efluente permitiu concluir uma diminuição do seu conteúdo poluente nos permeados com a diminuição do MWCO das membranas utilizadas. A diminuição simultânea de matéria orgânica e fenóis foi particularmente significativa no permeado da membrana de MWCO de 3,8 kDa que, por outro lado, apresenta uma melhoria significativa para o índice de biodegradabilidade e k (0,83;0,38-0,44 d-1), o que significa que este permeado apresenta já viabilidade para sofrer um processo biológico para remoção de matéria orgânica e o concentrado apresenta um elevado potencial para recuperação de taninos. Nas fracções de MWCO inferior a 3,8 kDa, a diminuição de matéria orgânica é muito significativa, com um aumento da sua fracção biodegradável. Embora os resultados não sejam totalmente conclusivos em termos de biodegradabilidade, esta fracção apresenta já características adequadas para reutilização como água de processo.

Optimização do processo de extracção por ultra-sons

Neste trabalho foi estudado o método de preparação de amostras baseado numa extracção ácida assistida por ultra-sons para a quantificação de metais pesados (Pb, Ni, Cd e Cr), em amostras de solo. Usou-se a espectrometria de absorção atómica com câmara de grafite (GFAAS) para quantificar os metais nestas amostras recolhidas em diferentes locais da cidade de Lisboa. A optimização dos parâmetros que influenciam a extracção dos metais por ultra-sons foi realizada a cinco variáveis: quantidade de amostra, volume de extractor (água-régia), tempo de sonificação, potência de sonificação e ciclo de sonificação. A eficiência do método foi testada por comparação dos resultados com os obtidos pela digestão ácida “tradicional” em banho de areia. A optimização do processo foi realizada para o metal chumbo. Os resultados analíticos obtidos por ambos os métodos apresentaram diferenças significativas. A extracção de chumbo das amostras, por ultra-sons, apresentou uma eficiência entre 65 a 78% quando comparada com o método “tradicional”. A recuperação de cádmio apresentou percentagens entre 36 e 90%. No caso do níquel e crómio, concluiu-se haver necessidade de optimizar o processo para cada um dos metais, pois apresentaram uma baixa taxa de recuperação.

Optical properties and transport in PLD-GaN

We present structural, optical and transport data on GaN samples grown by hybrid, two-step low temperature pulsed laser deposition. The band gap of samples with good crystallinity has been deduced from optical spectra. Large below gap band tails were observed. In samples with the lowest crystalline quality the PL spectra are quite dependent on spot laser incidence. The most intense PL lines can be attributed to excitons bounded to stacking faults. When the crystalline quality of the samples is increased the ubiquitous yellow emission band can be detected following a quenching process described by a similar activation energy to that one found in MOCVD grown samples. The samples with the highest quality present, besides the yellow band, show a large near band edge emission which peaked at 3.47 eV and could be observed up to room temperature. The large width of the NBE is attributed to effect of a wide distribution of band tail states on the excitons. Photoconductivity data supports this interpretation.

A new control strategy with saturation effect compensation for an autonomous induction generator drivenby wide speed range turbines

This paper presents a variable speed autonomous squirrel cage generator excited by a current-controlled voltage source inverter to be used in stand-alone micro-hydro power plants. The paper proposes a system control strategy aiming to properly excite the machine as well as to achieve the load voltage control. A feed-forward control sets the appropriate generator flux by taking into account the actual speed and the desired load voltage. A load voltage control loop is used to adjust the generated active power in order to sustain the load voltage at a reference value. The control system is based on a rotor flux oriented vector control technique which takes into account the machine saturation effect. The proposed control strategy and the adopted system models were validated both by numerical simulation and by experimental results obtained from a laboratory prototype. Results covering the prototype start-up, as well as its steady-state and dynamical behavior are presented. (C) 2011 Elsevier Ltd. All rights reserved.

Microstrip antenna array for multiband dedicated short range communications systems

Dedicated Short Range Communications (DSRC) is the key enabling technology for the present and future vehicular communication for various applications, such as safety improvement and traffic jam mitigation. This paper describes the development of a microstrip antenna array for the roadside equipment of a DSRC system, whose characteristics are according with the vehicular communications standards. The proposed antenna, with circular polarization, has a wide bandwidth, enough to cover the current European DSRC 5.8 GHz band and the future 5.9 GHz band for next generation DSRC communications. (C) 2011 Wiley Periodicals, Inc. Microwave Opt Technol Lett 53: 2794-2796, 2011; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.26394

Comunicações digitais através de ultra-sons em ambientes subaquáticos

Actualmente, as comunicações digitais em ambientes subaquáticos representam uma necessidade humana e um desafio à engenharia de sistemas. A maioria das aplicações dirigidas a meios subaquáticos recorre a sinais acústicos, já que relativamente a sinais de natureza electromagnética ou óptica, os sinais acústicos desfrutam de uma atenuação reduzida. Contudo, os meios subaquáticos possuem um comportamento complexo relativamente à propagação de sinais acústico, sendo caracterizados como canais dispersivos, no domínio do tempo e no domínio da frequência. Como os sistemas acústicos possuem uma largura de banda limitada, requer-se que um sistema de comunicação acústico subaquático seja, simultaneamente, eficiente na gestão dos recursos que possui e eficaz nos mecanismos que implementa para ultrapassar as limitações providenciadas pelo meio. Enquadrada neste âmbito, a presente dissertação propõe uma solução completa de um sistema de comunicação digital. Apresenta-se o dimensionamento de uma plataforma genérica, de baixo custo, que suporta a transmissão e recepção de sinais acústicos num ambiente subaquático. Através desta, verifica-se num meio subaquático real se as características deste ambiente coincidem com a informação presente na respectiva literatura científica. Adicionalmente, são analisadas quais as técnicas de processamento de sinal mais adequadas às comunicações digitais neste meio. Converge-se para uma solução baseada na modulação OFDM (Orthogonal Frequency Division Multiplexing), que alcança uma eficiência espectral de 2,95 bit/s/Hz, a um ritmo binário máximo de 103,288 kbit/s, numa largura de banda de 35 kHz. Através desta técnica, obtém-se elevada robustez aos efeitos de dispersão temporal do canal de comunicação, minimizando de forma eficaz a distorção de sinal devido à interferência inter-simbólica. Esta modulação multi-portadora recorre a sub-portadoras ortogonais, maximizando desta forma a eficiência espectral do sistema. Contudo, a ortogonalidade destas componentes pode ser comprometida pelo espalhamento de Doppler introduzido pelo canal subaquático. Para minimizar este efeito, é implementado um algoritmo adaptativo baseado na técnica LMS (Least Mean Squares).

Cork industry wastewater partition by ultra/nanofiltration: A biodegradation and valorisation study

Wastewater from cork processing industry present high levels of organic and phenolic compounds, such as tannins, with a low biodegradability and a significant toxicity. These compounds are not readily removed by conventional municipal wastewater treatment, which is largely based on primary sedimentation followed by biological treatment. The purpose of this work is to study the biodegradability of different cork wastewater fractions, obtained through membrane separation, in order to assess its potential for biological treatment and having in view its valorisation through tannins recovery, which could be applied in other industries. Various ultrafiltration and nanofiltration membranes where used, with molecular weight cut-offs (MWCO) ranging from 0.125 to 91 kDa. The wastewater and the different permeated fractions were analyzed in terms of Total Organic Carbon (TOC), Chemical Oxygen Demand (COD), Biochemical Oxygen Demand (BOD), Total Phenols (TP), Tannins, Color, pH and Conductivity. Results for the wastewater shown that it is characterized by a high organic content (670.5-1056.8 mg TOC/L, 2285-2604 mg COD/L, 1000-1225 mg BOD/L), a relatively low biodegradability (0.35-0.38 for BODs/COD and 0.44-0.47 for BOD20/COD) and a high content of phenols (360-410 mg tannic acid/L) and tannins (250-270 mg tannic acid/L). The results for the wastewater fractions shown a general decrease on the pollutant content of permeates, and an increase of its biodegradability, with the decrease of the membrane MWCO applied. Particularly, the permeated fraction from the membrane MWCO of 3.8 kDa, presented a favourable index of biodegradability (0.8) and a minimized phenols toxicity that enables it to undergo a biological treatment and so, to be treated in a municipal wastewater treatment plant. Also, within the perspective of valorisation, the rejected fraction obtained through this membrane MWCO may have a significant potential for tannins recovery. Permeated fractions from membranes with MWCO lower than 3.8 kDa, presented a particularly significant decline of organic matter and phenols, enabling this permeates to be reused in the cork processing and so, representing an interesting perspective of zero discharge for the cork industry, with evident environmental and economic advantages. (C) 2010 Elsevier Ltd. All rights reserved.

Design of a Multiband Full-Rate Ultra-Wideband Receiver in FPGA

MultiBand OFDM (MB-OFDM) UWB [1] is a short-range promising wireless technology for high data rate communications up to 480 Mbps. In this paper, we have designed and implemented in an Virtex-6 FPGA an MB-OFDM UWB receiver for the highest data rate of 480 Mbps. To test the system, we have also implemented an MB-OFDM transmitter and an AWGN generator in VHDL and determined the bit error rates at the receiver running in an FPGA.

Low Profile Multi-Band Antenna for Mobile Communications

In this paper, the design of low profile antennas by using Electromagnetic Band Gap (EBG) structures is introduced. Taking advantage of the fact that they can behave as Perfect Magnetic Conductor (PMC), it is shown that these structures exhibit dual band in-phase reflection at WLAN (Wireless Local Area Network) bands, the 2.4 GHz and 5.2 GHz bands. These structures are applied to PIFA (Planar Inverted-F Antenna) and the results show that it is possible to obtain low profile PIFA's.

a-SiH p-i-n structures with extreme i-layer thickness

We present measurements and numerical simulation of a-Si:H p-i-n detectors with a wide range of intrinsic layer thickness between 2 and 10 pm. Such a large active layer thickness is required in applications like elementary particle detectors or X-ray detectors. For large thickness and depending on the applied bias, we observe a sharp peak in the spectral response in the red region near 700 nm. Simulation results obtained with the program ASCA are in agreement with the measurement and permit the explanation of the experimental data. In thick samples holes recombine or are trapped before reaching the contacts, and the conduction mechanism is fully electron dominated. As a consequence, the peak position in the spectral response is located near the optical band gap of the a-Si:H i-layer. (C) 2009 Elsevier B.V. All rights reserved.