Reabilitação térmica e energética de edifício antigo: aplicação ao antigo edifício dos CTT em Coruche

O estudo desenvolvido no presente documento teve como alvo um edifício antigo construído entre 1930 e 1940 no concelho de Coruche, com construção característica da sua época. Numa fase inicial analisou-se de que forma se comporta o edifício em termos térmicos e energéticos, com base nas metodologias de cálculo apresentadas pelo regulamento térmico em vigor (RCCTE, 2006), e de seguida foram analisadas várias soluções existentes para a reabilitação térmica e energética do edifício que poderá ser concretizada, essencialmente devido às soluções para isolamento térmico das paredes, pavimentos e cobertura, assim como devido às soluções para vidros e caixilharia dos vãos envidraçados. Numa fase posterior, foi estudada a aplicação isolada das várias soluções de reabilitação consideradas, tendo sido simulada a aplicação de várias espessuras de isolante para as soluções da envolvente opaca e vários tipos de vidro duplo e caixilharia para as soluções da envolvente envidraçada, de forma a perceber-se a implicação que cada uma tem quanto à variação das necessidades energéticas do edifício. Por fim, foram calculados os custos de aplicação das várias soluções estudadas, com auxílio de um software de orçamentação, de forma que estas possam ser comparadas em termos da relação custo/benefício, em que, o benefício de cada solução será a variação provocada nas necessidades energéticas do edifício com aplicação da mesma. Assim, procurará encontrar-se para o edifício em estudo não só as soluções mais vantajosas em termos energéticos mas também as mais rentáveis, e procurará perceber-se se um investimento numa intervenção de reabilitação deste género conduzirá a um período de retorno do investimento reduzido, que possa ser considerado aceitável.

Structural characterization of Co‐Re superlattices

Co‐Re superlattices were prepared with nominal periodicities of 65–67 Å and varying bilayer composition. The structural characterization was made by x‐ray diffraction and Rutherford backscattering spectrometry (RBS). First, second, and third order satellites are observed in the x‐ray diffractogram at 2θ values and with intensities close to those predicted by simulation. This confirms the coherence of the superlattice. RBS measurements combined with RUMP simulations give information on interface sharpness and the absolute thicknesses of the Co and Re layers. Discrepancies between the experimental and simulated diffractograms are found for Co thicknesses below 18 Å.

Painéis fenólicos para aplicação em fachadas exteriores

Dissertação para obtenção do grau de Mestre em Engenharia Civil

Maintaining image quality for paediatric chest CTs while lowering dose: FBP versus SAFIRE

Objectives: Children have a greater risk from radiation, per unit dose, due to increased radiosensitivity and longer life expectancies. It is of paramount importance to reduce the radiation dose received by children. This research concerns chest CT examinations on paediatric patients. The purpose of this study was to compare the image quality and the dose received from imaging with images reconstructed with filtered back projection (FBP) and five strengths of Sinogram-Affirmed Iterative Reconstruction (SAFIRE). Methods: Using a multi-slice CT scanner, six series of images were taken of a paediatric phantom. Two kVp values (80 and 110), 3 mAs values (25, 50 and 100) and 2 slice thicknesses (1 mm and 3 mm) were used. All images were reconstructed with FBP and five strengths of SAFIRE. Ten observers evaluated visual image quality. Dose was measured using CT-Expo. Results: FBP required a higher dose than all SAFIRE strengths to obtain the same image quality for sharpness and noise. For sharpness and contrast image quality ratings of 4, FBP required doses of 6.4 and 6.8 mSv respectively. SAFIRE 5 required doses of 3.4 and 4.3 mSv respectively. Clinical acceptance rate was improved by the higher voltage (110 kV) for all images in comparison to 80 kV, which required a higher dose for acceptable image quality. 3 mm images were typically better quality than 1 mm images. Conclusion: SAFIRE 5 was optimal for dose reduction and image quality.

Rheo-optical characterization of liquid crystalline acetoxypropylcellulose melt undergoing large shear flow and relaxation after flow cessation

The rheological and structural characteristics of acetoxypropylcellulose (APC) nematic melt are studied at shear rates ranging from 10 s(-1) to 1000 s(-1) which are relevant to extrusion based processes. APC shows a monotonic shear thinning behavior over the range of shear rates tested. The negative extrudate-swell shows a minimum when a critical shear rate (gamma) over dot(c) is reached. For shear rates smaller than (gamma) over dot(c), the flow-induced texture consists of two set of bands aligned parallel and normal to the flow direction. At shear rates larger than (gamma) over dot(c), the flow induced texture is reminiscent of a 2 fluids structure. Close to the shearing walls, domains elongated along the flow direction and stacked along the vorticity are imaged with POM, whereas SALS patterns indicate that the bulk of the sheared APC is made of elliptical domains oriented along the vorticity. No full nematic alignment is achieved at the largest shear rate tested. Below (gamma) over dot(c), the stress relaxation is described by a stretched exponential. Above (gamma) over dot(c), the stress relaxation is described by a fast and a slow process. The latter coincides with the growth of normal bands thicknesses, as the APC texture after flow cessation consists of two types of bands with parallel and normal orientations relative to the flow direction. Both bands thicknesses do not depend on the applied shear rate, in contrast to their orientation. (C) 2015 Elsevier Ltd. All rights reserved.