Melhoria da eficiência energética do processo de produção de molas para a indústria automóvel

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Química e Biológica

Análise das condições de utilização de permutadores de calor de modo a serem economicamente rentáveis

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica Perfil Energia, Refrigeração e Climatização

Aplicação de redes neuronais artificiais à deteção e isolamento de falhas em processos industriais

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica

The effect of metal transfer modes and shielding gas composition on the emission of ultraafine particles in MAG steel welding

The present study aims to characterize ultrafine particles emitted during gas metal arc welding of mild steel and stainless steel, using different shielding gas mixtures, and to evaluate the effect of metal transfer modes, controlled by both processing parameters and shielding gas composition, on the quantity and morphology of the ultrafine particles. It was found that the amount of emitted ultrafine particles (measured by particle number and alveolar deposited surface area) are clearly dependent from the main welding parameters, namely the current intensity and the heat input of the Welding process. The emission of airborne ultrafine particles increases with the current intensity as fume formation rate does. When comparing the shielding gas mixtures, higher emissions were observed for more oxidizing mixtures, that is, with higher CO2 content, which means that these mixtures originate higher concentrations of ultrafine particles (as measured by number of particles. by cubic centimeter of air) and higher values of alveolar deposited surface area of particles, thus resulting in a more hazardous condition regarding welders exposure.

Industry energy optimization: A case study in a biodiesel production site

This paper presents a case study of heat exchanger network (HEN) retrofit with the objective to reduce the utilities consumption in a biodiesel production process. Pinch analysis studies allow determining the minimum duty utilities as well the maximum of heat recovery. The existence of heat exchangers for heat recovery already running in the process causes a serious restriction for the implementation of grassroot HEN design based on pinch studies. Maintaining the existing HEN, a set of alternatives with additional heat exchangers was created and analysed using some industrial advice and selection criteria. The final proposed solution allows to increase the actual 18 % of recovery heat of the all heating needs of the process to 23 %, with an estimated annual saving in hot utility of 35 k(sic)/y.

Choosing amine-based absorbents for CO2 capture

CO2 capture from gaseous effluents is one of the great challenges faced by chemical and environmental engineers, as the increase in CO2 levels in the Earth atmosphere might be responsible for dramatic climate changes. From the existing capture technologies, the only proven and mature technology is chemical absorption using aqueous amine solutions. However, bearing in mind that this process is somewhat expensive, it is important to choose the most efficient and, at the same time, the least expensive solvents. For this purpose, a pilot test facility was assembled and includes an absorption column, as well as a stripping column, a heat exchanger between the two columns, a reboiler for the stripping column, pumping systems, surge tanks and all necessary instrumentation and control systems. Some different aquous amine solutions were tested on this facility and it was found that, from a set of six tested amines, diethanol amine is the one that turned out to be the most economical choice, as it showed a higher CO2 loading capacity (0.982 mol of CO2 per mol of amine) and the lowest price per litre (25.70 ¤/L), even when compared with monoethanolamine, the benchmark solvent, exhibiting a price per litre of 30.50 ¤/L.

Single side damage simulations and detection in beam-like structures

Beam-like structures are the most common components in real engineering, while single side damage is often encountered. In this study, a numerical analysis of single side damage in a free-free beam is analysed with three different finite element models; namely solid, shell and beam models for demonstrating their performance in simulating real structures. Similar to experiment, damage is introduced into one side of the beam, and natural frequencies are extracted from the simulations and compared with experimental and analytical results. Mode shapes are also analysed with modal assurance criterion. The results from simulations reveal a good performance of the three models in extracting natural frequencies, and solid model performs better than shell while shell model performs better than beam model under intact state. For damaged states, the natural frequencies captured from solid model show more sensitivity to damage severity than shell model and shell model performs similar to the beam model in distinguishing damage. The main contribution of this paper is to perform a comparison between three finite element models and experimental data as well as analytical solutions. The finite element results show a relatively well performance.

Estudo comparativo de sistemas em aquecimento

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica

Reabilitação sustentável de edifício de habitação, em construção tradicional, no Baixo Alentejo

Dissertação de Final de Mestrado para obtenção do grau de Mestre em Engenharia Civil Especialização em Edificações

First Curl, Then Wrinkle

The excellent properties of elastomers are exploited to trigger wrinkling instabilities in curved shells. Micro- and nano-fibres are produced by electrospinning and UV irradiated: each fibre consists of a soft core and a stiff outer half-shell. Upon solvent de-swelling, the fibres curl because the shell and the core have different natural lengths. Wrinkling only starts after the fibre has attained a well-defined helical shape. A simple analytical model is proposed to find the curling curvature and wrinkle wavelength, as well as the transition between the “curling” and “wrinkling” regimes. This new instability resembles that found in the tendrils of climbing plants as they dry and lignify.

Projecto de verificação do comportamento térmico de um edifício de habitação: análise e comparação de resultados obtidos com recurso a duas ferramentas de cálculo

O trabalho de projecto desenvolvido tem por objectivo a análise dos resultados obtidos na verificação térmica de edifícios aquando da utilização de programas de cálculo automático. Para o efeito, foram escolhidos dois edifícios unifamiliares com características distintas, tentando que fossem abrangidas o máximo de situações diferentes. Neste projecto foram avaliados sobretudo dois aspectos: quantificação das áreas e desenvolvimentos dos elementos da envolvente dos edifícios em estudo e cálculo dos coeficientes de transmissão térmica superficial e linear dos elementos construtivos. Com base neste trabalho, pode-se promover uma melhoria dos programas de cálculo automático no mercado, de modo a assegurar uma maior qualidade dos projectos de edifícios e consequente reflexo na qualidade da construção civil futura. Por último, apresentam-se as conclusões e possibilidades de desenvolvimento de trabalhos futuros.