Non-selective optical wavelength-division multiplexing devices based on a-SiC:H multilayer heterostuctures

In this paper we present results on the optimization of multilayered a-SiC:H heterostructures for wavelength-division (de) multiplexing applications. The non selective WDM device is a double heterostructure in a glass/ITO/a-SiC:H (p-i-n) /a-SiC:H(-p) /a-Si:H(-i')/a-SiC:H (-n')/ITO configuration. The single or the multiple modulated wavelength channels are passed through the device, and absorbed accordingly to its wavelength, giving rise to a time dependent wavelength electrical field modulation across it. The effect of single or multiple input signals is converted to an electrical signal to regain the information (wavelength, intensity and frequency) of the incoming photogenerated carriers. Here, the (de) multiplexing of the channels is accomplished electronically, not optically. This approach offers advantages in terms of cost since several channels share the same optical components; and the electrical components are typically less expensive than the optical ones. An electrical model gives insight into the device operation.

Bias dependent photocurrent collection in p-i-n a-Si : EVSiC : H heterojunction

A series of large area single layers and heterojunction cells in the assembly glass/ZnO:Al/p (SixC1-x:H)/i (Si:H)/n (SixC1-x:H)/Al (0 carriers the diffusion.

Bias-dependent photocurrent collection in p-i-n a-Si : H/SiC : H heterojunction

A series of large area single layers and glass/ZnO:AVp(SixC1-x:H)/i(Si:H)/n(SixC1-x:H)/AI (0 < x < 1) heterojunction cells were produced by plasma-enhanced chemical vapour deposition (PE-CVD) at low temperature. Junction properties, carrier transport and photogeneration are investigated from dark and illuminated current-voltage (J-V) and capacitance-voltage (C-V) characteristics. For the heterojunction cells atypical J-V characteristics under different illumination conditions are observed leading to poor fill factors. High series resistances around 106 Q are also measured. These experimental results were used as a basis for the numerical simulation of the energy band diagram, and the electrical field distribution of the structures. Further comparison with the sensor performance gave satisfactory agreement. Results show that the conduction band offset is the most limiting parameter for the optimal collection of the photogenerated carriers. As the optical gap increases and the conductivity of the doped layers decreases, the transport mechanism changes from a drift to a diffusion-limited process.

New stacked photodevices for signal multiplexing and demultiplexing applications in the visible spectrum

Results on the use of a double a-SiC:H p-i-n heterostructure for signal multiplexing and demultiplexing applications in the visible range are presented. Pulsed monochromatic beams together (multiplexing mode), or a single polychromatic beam (demultiplexing mode) impinge on the device and are absorbed, accordingly to their wavelength. Red, green and blue pulsed input channels are transmitted together, each one with a specific transmission rate. The combined optical signal is analyzed by reading out, under different applied voltages, the generated photocurrent. Results show that in the multiplexing mode the output signal is balanced by the wavelength and transmission rate of each input channel, keeping the memory of the incoming optical carriers. In the demultiplexing mode the photocurrent is controlled by the applied voltage allowing regaining the transmitted information. A physical model supported by a numerical simulation gives insight into the device operation.

Optical demultiplexer device operating in the visible spectrum

In this paper, we present results on the use of multilayered a-SiC:H heterostructures as a device for wavelength-division demultiplexing of optical signals. These devices are useful in optical communications applications that use the wavelength division multiplexing technique to encode multiple signals into the same transmission medium. The device is composed of two stacked p-i-n photodiodes, both optimized for the selective collection of photo generated carriers. Band gap engineering was used to adjust the photogeneration and recombination rate profiles of the intrinsic absorber regions of each photodiode to short and long wavelength absorption in the visible spectrum. The photocurrent signal using different input optical channels was analyzed at reverse and forward bias and under steady state illumination. A demux algorithm based on the voltage controlled sensitivity of the device was proposed and tested. An electrical model of the WDM device is presented and supported by the solution of the respective circuit equations.

Electrical transport properties of CuS single crystals

Electrical resistivity, transverse magnetoresistance and thermoelectric power measurements were performed on CuS high quality single crystals in the range 1.2-300 K and under fields of up to 16 T. The zero field resistivity data are well described below 55 K by a quasi-2D model, consistent with a carrier confinement at lower temperatures, before the transition to the superconducting state. The transverse magnetoresistance develops mainly below 30 K and attains values as large as 470% for a 16 T field at 5 K, this behaviour being ascribed to a band effect mechanism, with a possible magnetic field induced DOS change at the Fermi level. The transverse magnetoresistance shows no signs of saturation, following a power law with field Delta rho/rho(0) proportional to H(1.4), suggesting the existence of open orbits for carriers at the Fermi surface. The thermoelectric power shows an unusual temperature dependence, probably as a result of the complex band structure of CuS.

Análise do desempenho do automóvel híbrido face ao de combustão interna

Os veículos híbridos são parte da solução atual para reduzir o consumo de combustível e emissões de gases de escape, são reconhecidos pela sociedade e contribuem para o desenvolvimento da mobilidade de uma forma ambientalmente sustentável, despertando a consciência coletiva para a correta utilização dos recursos energéticos. Este trabalho descreve um estudo sobre três automóveis, que têm de comum o mesmo bloco de motor de combustão, mas utilizam-no associado a tecnologias diferentes, sendo um convencional, um de tecnologia não completamente híbrido (híbrido mínimo), e outro de tecnologia completamente híbrido (híbrido total). Inicialmente foi efetuada uma pesquisa sobre a tecnologia e modo de funcionamento do automóvel híbrido. Soluções como recuperação de energia dissipada pela travagem, paragem automática do motor de combustão interna ao ralenti, desativação parcial ou total de cilindros motor para poupar combustível, estão associadas aos automóveis híbridos estudados, permitindo mesmo quando aplicadas aos automóveis convencionais modernos torná-los mais eficientes e menos poluentes. De modo a identificar as principais diferenças entre os três automóveis foram realizados testes de estrada, reproduzindo uma utilização real baseada no Novo Ciclo de Condução Europeu, com uma recolha representativa e significativa de condições reais de condução. Foram considerados fatores como passividade/agressividade de condução ao volante do condutor, perfis de velocidade, aceleração, eficiência da transmissão, resistência ao rolamento coeficiente de resistência aerodinâmica com condições variáveis de vento junto ao mar e serra. Registou-se a influência do peso e hábitos de condução no consumo de combustível, possibilitando identificar desvios, intervalos e limites expectáveis de desempenho e consumo para cada um dos carros. Esta tese permitiu desenvolver conhecimentos para melhor entender as vantagens e condicionantes de utilização do automóvel híbrido, onde a redução de consumo de combustível e custo de exploração é a recompensa, pela utilização da mais-valia tecnológica.

O regime de exigibilidade de caixa no IVA

Mestrado em Contabilidade

Programa de manutenção de aeronaves das companhias de aviação de baixo custo

Este trabalho aborda o Programa de Manutenção de Aeronaves das companhias de aviação de baixo custo, tendo como foco a análise e identificação dos requisitos legais e das metodologias de desenvolvimento de um Programa de Manutenção de uma aeronave e a comparação dos custos de manutenção de companhias de baixo custo com as companhias regulares. A aplicação eficaz de um programa de manutenção, para além de reduzir os seus custos, tem um impacto positivo na segurança, economia da manutenção e na fiabilidade de despacho. A metodologia utilizada foi a análise de informação de publicações e artigos. Com base na revisão de literaturas especializadas, fez-se uma selecção dos diversos aspectos necessários para se obter um Programa de Manutenção, o que permitiu construir o caso de estudo e efectuar a análise dos custos inerentes de manutenção de um operador aéreo de baixo custo e de um operador aéreo regular. Os resultados da análise permitiram chegar a veracidade da hipótese de que do ponto de vista de manutenção é igualmente seguro ou não seguro voar numa companhia de baixo custo e numa companhia regular, assim independentemente do tipo de companhia, ambas devem cumprir os requisitos para aprovação do PMA imposto pela autoridade aeronáutica, para garantir a aeronavegabilidade das aeronaves, ou seja, a sua segurança para a condição de voo, sem pôr em causa o carimbo baixo custo ou regular da companhia.

Capacitive effects in pinpin photodiodes

The application of a-SiC:H/a-Si:H pinpin photodiodes for optoelectronic applications as a WDM demultiplexer device has been demonstrated useful in optical communications that use the WDM technique to encode multiple signals in the visible light range. This is required in short range optical communication applications, where for costs reasons the link is provided by Plastic Optical Fibers. Characterization of these devices has shown the presence of large photocapacitive effects. By superimposing background illumination to the pulsed channel the device behaves as a filter, producing signal attenuation, or as an amplifier, producing signal gain, depending on the channel/background wavelength combination. We present here results, obtained by numerical simulations, about the internal electric configuration of a-SiC:H/a-Si:H pinpin photodiode. These results address the explanation of the device functioning in the frequency domain to a wavelength tunable photo-capacitance due to the accumulation of space charge localized at the bottom diode that, according to the Shockley-Read-Hall model, it is mainly due to defect trapping. Experimental result about measurement of the photodiode capacitance under different conditions of illumination and applied bias will be also presented. The combination of these analyses permits the description of a wavelength controlled photo-capacitance that combined with the series and parallel resistance of the diodes may result in the explicit definition of cut off frequencies for frequency capacitive filters activated by the light background or an oscillatory resonance of photogenerated carriers between the two diodes. (C) 2013 Elsevier B.V. All rights reserved.

Direct Color Sensor, Optical Amplifier and Demux Device Integrated on a Single Monolithic SiC Photodetector

A pi'n/pin a-SiC:H voltage and optical bias controlled device is presented and its behavior as image and color sensor, optical amplifier and demux device is discussed. The design and the light source properties are correlated with the sensor output characteristics. Different readout techniques are used. When a low power monochromatic scanner readout the generated carriers the transducer recognizes a color pattern projected on it acting as a direct color and image sensor. Scan speeds up to 10(4) lines per second are achieved without degradation in the resolution. If the photocurrent generated by different monochromatic pulsed channels is readout directly, the information is demultiplexed. Results show that it is possible to decode the information from three simultaneous color channels without bit errors at bit rates per channel higher than 4000 bps. Finally, when triggered by light of appropriated wavelength, it can amplify or suppress the generated photocurrent working as an optical amplifier (C) 2009 Published by Elsevier Ltd.

Transvase : quando a ficção invade a realidade

ABSTRACT: Adopting the concept of metalepsis, as explained by Gérard Genette, I intend to tackle the miscegenation of ontological worlds as practiced in metacinematic films dealing either with the creator or the spectator and made famous with Woody Allen’s film The Purple Rose of Cairo (1985, EUA). Assuming the existence of two adjoining fictional universes, one of them intrafilmically projected onto a screen and the other positioned in front of it so as to create or observe the other, one realizes that, in fact, they both communicate in a more intense way. That is, they both can cross the barrier that separates them and function, literally, as communicating vessels thrusting themselves onto the other side of fiction. The use of this screen passage technique – which I call ‘spilling narrative’ – although it takes place inside the film, at an intradiegetic level, cannot be considered a simple comic effect. In actuality, it is a very serious affair, denoting the authorial intervention as a reflexive practice of écriture by means of a mise en abyme, according to Lucien Dällenbach. Therefore, the fictional spilling over of worlds which totally blends together both sides of the twice artificial universe of the fabula, represents the emotional and intellectual involvement of the creator with his/her creation and of the spectator with the world watched. Both illustrate the desire of fusion inherent in the acts of creation and reception. My approach will be based on Gabriele Salvatores’ Happy Family (2010) and Wojciech Marczewski’s Escape from the ‘Liberty’ Cinema (1990).

Mutation accumulation in Tetrahymena

Background - The rate and fitness effects of mutations are key in understanding the evolution of every species. Traditionally, these parameters are estimated in mutation accumulation experiments where replicate lines are propagated in conditions that allow mutations to randomly accumulate without the purging effect of natural selection. These experiments have been performed with many model organisms but we still lack empirical estimates of the rate and effects of mutation in the protists. Results - We performed a mutation accumulation (MA) experiment in Tetrahymena thermophila, a species that can reproduce sexually and asexually in nature, and measured both the mean decline and variance increase in fitness of 20 lines. The results obtained with T. thermophila were compared with T. pyriformis that is an obligate asexual species. We show that MA lines of T. thermophila go to extinction at a rate of 1.25 clonal extinctions per bottleneck. In contrast, populations of T. pyriformis show a much higher resistance to extinction. Variation in gene copy number is likely to be a key factor in explaining these results, and indeed we show that T. pyriformis has a higher mean copy number per cell than T. thermophila. From fitness measurements during the MA experiment, we infer a rate of mutation to copy number variation of 0.0333 per haploid MAC genome of T. thermophila and a mean effect against copy number variation of 0.16. A strong effect of population size in the rate of fitness decline was also found, consistent with the increased power of natural selection. Conclusions - The rate of clonal extinction measured for T. thermophila is characteristic of a mutational degradation and suggests that this species must undergo sexual reproduction to avoid the deleterious effects detected in the laboratory experiments. We also suggest that an increase in chromosomal copy number associated with the phenotypic assortment of amitotic divisions can provide an alternative mechanism to escape the deleterious effect of random chromosomal copy number variation in species like T. pyriformis that lack the resetting mechanism of sexual reproduction. Our results are relevant to the understanding of cell line longevity and senescence in ciliates.

Fat intake interacts with polymorphisms of Caspase9, FasLigand and PPARgamma apoptotic genes in modulating Crohn's disease activity

Background & aims: Crohn’s disease (CD) is a multifactorial disease where resistance to apoptosis is one major defect. Also, dietary fat intake has been shown to modulate disease activity. We aimed to explore the interaction between four single nucleotide polymorphisms (SNPs) in apoptotic genes and dietary fat intake in modulating disease activity in CD patients. Methods: Polymerase Chain Reaction (PCR) and Restriction Fragment Length Polymorphism (RFLP) techniques were used to analyze Caspase9þ93C/T, FasLigand-843C/T, Peroxisome Proliferator-Activated Receptor gammaþ161C/T and Peroxisome Proliferator-Activated Receptor gamma Pro12Ala SNPs in 99 patients with CD and 116 healthy controls. Interactions between SNPs and fat intake in modulating disease activity were analyzed using regression analysis. Results: None of the polymorphisms analyzed influenced disease susceptibility and/or activity, but a high intake of total, saturated and monounsaturated fats and a higher ratio of n-6/n-3 polyunsaturated fatty acids (PUFA), was associated with a more active phenotype (p < 0.05). We observed that the detrimental effect of a high intake of total and trans fat was more marked in wild type carriers of the Caspase9þ93C/T polymorphism [O.R (95%CI) 4.64 (1.27e16.89) and O.R (95%CI) 4.84 (1.34e17.50)]. In the Peroxisome Proliferator-Activated Receptor gamma Pro12Ala SNP, we also observed that a high intake of saturated and monounsaturated fat was associated to a more active disease in wild type carriers [OR (95%CI) 4.21 (1.33e13.26) and 4.37 (1.52e12.51)]. Finally, a high intake of n-6 PUFA was associated with a more active disease in wild type carriers for the FasLigand-843C/T polymorphism [O.R (95%CI) 5.15 (1.07e24.74)]. Conclusions: To our knowledge, this is the first study to disclose a synergism between fat intake and SNPs in apoptotic genes in modulating disease activity in CD patients.

IL23R polymorphisms influence phenotype and response to therapy in patients with ulcerative colitis

Objective - We aimed to identify the clinical and genetic [IL23 receptor (IL23R) single nucleotide polymorphisms (SNPs)] predictors of response to therapy in patients with ulcerative colitis. Patients and methods - A total of 174 patients with ulcerative colitis, 99 women and 75 men, were included. The mean age of the patients was 47±15 years and the mean disease duration was 11±9 years. The number of patients classified as responders (R) or nonresponders (NR) to several therapies was as follows: 110 R and 53 NR to mesalazine (5-ASA), 28 R and 20 NR to azathioprine (AZT), 18 R and 7 NR to infliximab. Clinical and demographic variables were recorded. A total of four SNPs were studied: IL23R G1142A, C2370A, G43045A, and G9T. Genotyping was performed by real-time PCR using Taqman probes. Results - Older patients were more prone to respond to 5-ASA (P=0.004), whereas those with pancolitis were less likely to respond to such therapies (P=0.002). Patients with extraintestinal manifestations (EIMs) were less likely to respond to 5-ASA (P=0.001), AZT (P=0.03), and corticosteroids (P=0.06). Carriers of the mutant allele for IL23R SNPs had a significantly higher probability of developing EIMs (P<0.05), a higher probability of being refractory to 5-ASA (P<0.03), but a higher likelihood of responding to AZT (P=0.05). A significant synergism was observed between IL23R C2370A and EIMs with respect to nonresponse to 5-ASA (P=0.03). Conclusion - Besides extent of disease and age at disease onset, the presence of EIMs may be a marker of refractoriness to 5-ASA, corticosteroids, and AZT. IL23R SNPs are associated both with EIMs and with nonresponse to 5-ASA and corticosteroids.