Synthesis of Fe/Ti oxides from a single source alkoxide precursor under inert atmosphere

The heterometal alkoxide [FeCl{Ti2(OPr i)9}] (1) was employed as a single source precursor for the preparation of Fe/Ti oxides under inert atmosphere. Three different synthetic procedures were adopted in the processing of 1, either employing aqueous HNO3 or HCl solutions, or in the absence of mineral acids. Products were characterised by powder X-ray diffractometry, scanning electron microscopy combined with energy dispersive X-ray spectroscopy (SEM/EDS) and Raman, electron paramagnetic resonance (EPR) and Mössbauer spectroscopies. Oxide products contained titanium(IV) and either iron(III) or iron(II), depending on reaction conditions and thermal treatment temperatures. An interesting iron(III)→iron(II) reduction was observed at 1000 ºC in the HNO3-containing system, leading to the detection of ilmenite (FeTiO3). SEM/EDS studies revealed a highly heterogeneous metal distribution in all products, possibly related to the presence of a significant content of carbon and of structural defects (oxygen vacancies) in the solids.

Porcine skin as a source of biodegradable matrices: alkaline treatment and glutaraldehyde crosslinking

In this work, the modifications promoted by alkaline hydrolysis and glutaraldehyde (GA) crosslinking on type I collagen found in porcine skin have been studied. Collagen matrices were obtained from the alkaline hydrolysis of porcine skin, with subsequent GA crosslinking in different concentrations and reaction times. The elastin content determination showed that independent of the treatment, elastin was present in the matrices. Results obtained from in vitro trypsin degradation indicated that with the increase of GA concentration and reaction time, the degradation rate decreased. From thermogravimetry and differential scanning calorimetry analysis it can be observed that the collagen in the matrices becomes more resistant to thermal degradation as a consequence of the increasing crosslink degree. Scanning electron microscopy analysis indicated that after the GA crosslinking, collagen fibers become more organized and well-defined. Therefore, the preparations of porcine skin matrices with different degradation rates, which can be used in soft tissue reconstruction, are viable.

Mechanical, thermal and morphological properties of glutaraldehyde crosslinked bovine pericardium followed by glutamic acid treatment

Major problems with valve bioprostheses are associated with progressive structural deterioration and calcification, directly associated with the use of glutaraldehyde (GA). This work describes the effects of GA processing and borate/glutamic acid buffer treatment on the mechanical, thermal and morphological properties of 0.5% GA crosslinked bovine pericardium (BP). The results showed that while the treatment of 0.5% GA crosslinked BP with borate/glutamic acid significantly improves the mechanical properties, it had no visible effect on surface morphology. Better surface preservation was only achieved for BP pre-treated with a lower GA concentration followed by the conventional treatment (0.5% GA). Improvements in mechanical properties probably arises from structural changes probably involving the depolymerization of polymeric GA crosslinks and an increase electrostatic interaction due to covalent binding of glutamic acid to free carbonyl groups (Schiff base).The results indicate that the treatment GA crosslinked BP with borate/glutamic acid buffer may be an attractive procedure for the manufacture of heart valve bioprostheses.

Photodynamic antimicrobial chemotherapy (PACT) for the treatment of malaria, leishmaniasis and trypanosomiasis

A photodynamic effect occurs when photosensitiser molecules absorb light and dissipate the absorbed energy by transferring it to biological acceptors (usually oxygen), generating an excess of reactive species that are able to force cells into death pathways. Several tropical diseases present physiopathological aspects that are accessible to the application of a photosensitiser and local illumination. In addition, disease may be transmitted through infected blood donations, and many of the aetiological agents associated with tropical diseases have been shown to be susceptible to the photodynamic approach. However, there has been no systematic investigation of the application of photoantimicrobial agents in the various presentations, whether to human disease or to the disinfection of blood products or even as photo-insecticides. We aim in this review to report the advances in the photoantimicrobial approach that are beneficial to the field of anti-parasite therapy and also have the potential to facilitate the development of low-cost/high-efficiency protocols for underserved populations.

Effect of experimental heat treatment on mechanical properties of resin composites

The aim of this study was to verify the influence of an experimental heat treatment (170ºC/10 min) using a casting furnace on the mechanical properties (hardness and flexural strength) of 2 commercial direct resin composites (TPH Spectrum and Filtek P60) compared to a commercial indirect resin system (BelleGlass). Heat treatment temperature was determined after thermal characterization by thermogravimetry (TG) and differential scanning calorimetry (DSC). Data was analyzed by ANOVA and Tukey's test at 5% significance level. There was statistical significance for the main factor heat treatment (p=0.03) and composite (p=0.02), for flexural strength. For Knoop hardness, only the main factor composite was statistically significant (p=0.00). P60 presented higher hardness than TPH. No statistically significant correlation between mechanical properties tested was detected. Based on these results, it was possible to conclude that heat treatment influenced flexural strength of direct composites, while it was not observed for hardness. The association of direct composites with a simple post-cure heat treatment may be an alternative for current indirect composite systems, although more studies are needed to verify other properties of the composites for this application.

Mineral and vitamin content of beef, chicken, and turkey hydrolysates mineral and vitamin content of protein hydrolysates

The purpose of this study was to assess the concentration of vitamins and minerals in meat protein hydrolysates. Calcium, phosphorus and iron were analyzed by inductively coupled-plasma atomic emission spectrophotometry; vitamin C was analyzed by the reduction of cupric ions and vitamins B1 and B2 by fluorescence. Regarding minerals, the beef hydrolysate (BH) had more iron than the turkey hydrolysate (TH) and the chicken hydrolysate (CH); TH had a little more phosphorus. BH had the largest amount of vitamin C, and similar amounts of vitamins B1 and B2. The amount of these nutrients found in the hydrolysates suggests that it is possible to use them to enrich special dietary formulations.

Efeito da inclusão de diferentes fontes lipídicas e óleo mineral na dieta sobre a digestibilidade dos nutrientes e os níveis plasmáticos de gordura em equinos

Objetivou-se avaliar os efeitos da inclusão de gordura de origem animal ou vegetal e de óleo mineral sobre a aceitabilidade, a digestibilidade dos nutrientes e as concentrações plasmáticas de triglicérides e colesterol em equinos. Utilizaram-se quatro potros de 13 a 16 meses de idade recebendo dieta contendo feno de gramínea e concentrado, em delineamento quadrado latino, analisado por contrastes ortogonais. A aceitabilidade não foi influenciada pela quantidade nem pelo tipo de óleo adicionado às dietas. Os menores valores de digestibilidade de matéria seca (MS), matéria orgânica (MO) e extrato etéreo (EE) foram observados para as dietas acrescidas de óleo mineral (58,90; 60,29 e 32,02%) em comparação à dieta controle, cujos valores foram de 62,58; 64,41 e 77,72%. O coeficiente de digestibilidade do EE obtido com a dieta com óleo mineral foi menor (32,02%) que o obtido para as dietas com gordura animal (90,26%) e gordura vegetal (86,47%). A dieta com óleo mineral reduziu a concentração de HDL-C (68,75 mg/dL) em relação à dieta controle (76,00 mg/dL). A adição de fontes lipídicas e óleo mineral não influencia na aceitabilidade da dieta por equinos. O óleo vegetal não se diferencia da gordura animal quanto à digestibilidade dos nutrientes, no entanto, essas fontes de lipídios afetam a digestibilidade do extrato etéreo. A adição de óleo mineral reduz os níveis plasmáticos de HDL-C, ao passo que a adição de gordura animal e gordura vegetal não altera as concentrações plasmáticas de colesterol.

Densidade mineral óssea, composição corporal e ingestão alimentar de adolescentes modelos de passarela

OBJETIVO: Avaliar a densidade mineral óssea (DMO) e relacioná-la com a ingestão alimentar e composição corporal de adolescentes modelos de passarela. MÉTODOS: Estudo transversal avaliando 33 modelos e 33 não modelos de 15 a 18 anos pareadas por idade e índice de massa corporal (IMC). A densidade mineral óssea da coluna (L1-L4) foi avaliada por meio da técnica da absorciometria de feixe duplo de energia (Lunar® DPX Alpha), e a composição corporal, pela técnica de pletismografia. A ingestão alimentar foi avaliada por meio do registro alimentar de 3 dias. RESULTADOS: A média de idade das adolescentes foi de 16,75±1,04 anos, sendo que 24 por cento apresentaram IMC abaixo dos valores ideais para a idade. Não houve diferença de DMO entre modelos (1,108±0,080 g/cm2) e não modelos (1,096±0,102 g/cm2) (p > 0,05), sendo identificada uma porcentagem de 6 por cento de baixa DMO para a idade. Observou-se que a média de ingestão de energia foi menor entre as modelos em comparação às adolescentesnão modelos (1.480,93±582,95 versus 1.973,00±557,63 kcal) (p > 0,05) e que a maioria das adolescentes de ambos os grupos apresentou consumo inadequado de micronutrientes, ressaltando-se a baixa ingestão de cálcio. Verificou-se correlação significativa da DMO apenas com a massa magra (kg) (modelos r = 0,362 e não modelos r = 0,618; p < 0,05). CONCLUSÃO: Apesar de não ter sido encontrada associação entre a DMO, o IMC e a ingestão de nutrientes importantes no processo de mineralização óssea, as inadequações na ingestão alimentar podem influenciar negativamente a aquisição de massa óssea, que se encontra potencializada neste estágio de vida

Metabolic osteopathy in celiac disease: importance of a gluten-free diet

Reduced bone mineral density (BMD) is frequently found in individuals with untreated celiac disease (CD), possibly due to calcium and vitamin D malabsorption, release of pro-inflammatory cytokines, and misbalanced bone remodeling. A gluten-free diet (GFD) promotes a rapid increase in BMD that leads to complete recovery of bone mineralization in children. Children may attain normal peak bone mass if the diagnosis is made and treatment is given before puberty, thereby preventing osteoporosis in later life. A GFD improves, but rarely normalizes, BMD in patients diagnosed with CD in adulthood. In some cases, nutritional supplementation may be necessary. More information on therapeutic alternatives is needed

Evaluation of timing and responses to physiotherapeutic treatment

In several treatment regimens, the recognition of chronobiology contributes to the therapeutic process through the effective use of temporization protocols. The purpose of the present study was to evaluate the relationship between the tic treatment and the time of day when such treatment was performed, as well as the chronotype of orthopedic and rheumatologic patients in a clinical physiotherapy school. The population studied was treated in the morning and evening periods. The patients were divided into three groups of pathologies with similar treatments, which were as follows: syndrome of shoulder impact (n=33), knee artrosis (n=17), and lombalgia (n=23). At the end of ten treatment sessions, data concerning pain, percentage of subjective improvement, chronotype and age were compared. At the end of the study, it was observed that the time of day when treatment was performed influenced the results of individuals treated in the evenings but had no influence on the individuals treated in the morning. In addition, the evening schedule was the most well suited for intermediate individuals.

Influence of Annealing Heat Treatment and Cr, Mg, and Ti Alloying on the Mechanical Properties of High-Silicon Cast Iron

The influence of annealing on the mechanical properties of high-silicon cast iron for three alloys with distinct chromium levels was investigated. Each alloy was melted either with or without the addition of Ti and Mg. These changes in the chemical composition and heat treatment aimed to improve the material's mechanical properties by inhibiting the formation of large columnar crystals, netlike laminae, precipitation of coarse packs of graphite, changing the length and morphology of graphite, and rounding the extremities of the flakes to minimize the stress concentration. For alloys with 0.07 wt.% Cr, the annealing reduced the impact resistance and tensile strength due to an enhanced precipitation of refined carbides and the formation of interdendritic complex nets. Annealing the alloys containing Ti and Mg led to a decrease in the mechanical strength and an increase in the toughness. Alloys containing approximately 2 wt.% Cr achieved better mechanical properties as compared to the original alloy. However, with the addition of Ti and Mg to alloys containing 2% Cr, the chromium carbide formation was inhibited, impairing the mechanical properties. In the third alloy, with 3.5 wt.% of Cr additions, the mechanical strength improved. The annealing promoted a decrease in both hardness and amount of iron and silicon complex carbides. However, it led to a chromium carbide formation, which influenced the mechanical characteristics of the matrix of the studied material.

Health services performance for TB treatment in Brazil: a cross-sectional study

Background: Researches to evaluate Primary Health Care performance in TB control in Brazil show that different cities aggregate local specificities in the dynamics of coping with the disease. This study aims to evaluate health services' performance in TB treatment in cities across different Brazilian regions. Methods: This cross-sectional study was conducted in five cities that are considered priorities for TB control in Brazil: Itaborai (ITA), Ribeirao Preto (RP) and Sao Jose do Rio Preto (SJRP) in the Southeast; Campina Grande (CG) and Feira de Santana (FS) in the Northeast. Data were collected through interviews with 514 TB patients under treatment in 2007, using the Primary Care Assessment Tool adapted for TB care in Brazil. Indicators were constructed based on the mean response scores (Likert scale) and compared among the study sites. Results: ""Access to treatment"" was evaluated as satisfactory in the Southeast and regular in the Northeast, which displayed poor results on 'home visits' and 'distance between treatment site and patient's house'. ""Bond"" was assessed as satisfactory in all cities, with a slightly better performance in RP and SJRP. ""Range of services"" was rated as regular, with better performance of southeastern cities. 'Health education', 'DOT' and 'food vouchers' were less offered in the Northeast. ""Coordination"" was evaluated as satisfactory in all cities. ""Family focus"" was evaluated as satisfactory in RP and SJRP, and regular in the others. 'Professional asking patient's family about other health problems' was evaluated as unsatisfactory, except in RP. Conclusions: Two types of obstacles are faced for health service performance in TB treatment in the cities under analysis, mainly in the Northeast. The first is structural and derives from difficulties to access health services and actions. The second is organizational and derives from the way health technologies and services are distributed and integrated. Incentives to improve care organization and management practices, aimed at the integration of primary, secondary and tertiary services, can contribute towards a better performance of health services in TB treatment.

EFFECTS OF THERMAL TREATMENT ON THE PHYSICOCHEMICAL CHARACTERISTICS OF GIANT BAMBOO

Despite countless use possibilities for bamboo, this material has two major disadvantages. One drawback is the low natural durability of most bamboo species due to presence of starch in their parenchyma cells. The other equally important drawback is the tendency bamboo has to present dimensional variations if subjected to environmental change conditions. In an attempt to minimize these inconveniences, strips (laths) of Dendrocalamus giganteus Munro were taken from different portions of the culm and subjected to several temperatures, namely 140 degrees C, 180 degrees C, 220 degrees C, 260 degrees C and 300 degrees C under laboratory conditions, at the ESALQ-USP college of agriculture. The thermal treatment process was conducted in noninert and inert atmospheres (with nitrogen), depending on temperature Specimens were then subjected to physicomechanical characterization tests in order to determine optimum thermal treatment conditions in which to preserve to the extent possible the original bamboo properties. Results revealed that there is an optimum temperature range, between 140 degrees and 220 degrees C, whereby thermally treated bamboo does not significantly lose its mechanical properties while at the same time showing greater dimensional stability in the presence of moisture.