Piezoceramic Composite Actuators for Flow Control in Low Reynolds Number Airflow

The research presented here employs solid-state actuators for flow separation delay or for forced attachment of separated flow seen in airfoils at low Reynolds numbers. To reduce separation, periodic excitation to the flow around the leading edge of the airfoil is induced by Macro-Fiber Composite actuated clamped-free unimorph benders. An electromechanical model of the unimorph is briefly presented and parametric study is conducted to aid the design of a unimorph to output high deformation at a desired frequency. The optimum frequency and amplitude for lift improvement at post-stall angles are identified experimentally. Along with aerodynamic force and structural displacement measurements, helium bubble flow visualization is used to verify existing separated flow, and the attached flow induced by flow control. The lift enhancement induced by several flow control techniques is compared. A symmetric and non-uniform (3D) flow excitation results in the maximum lift enhancement at post-stall region at the lowest power consumption level. A maximum lift coefficient increase of 27.5% (in the post-stall region) is achieved at 125 Hz periodic excitation, with the 3D symmetric actuation mode at 5 m/s and the reduced frequency of 3.78. C(l,max) is increased 7.6% from the baseline.

Hybrid fault diagnosis scheme implementation for power distribution systems automation

Power distribution automation and control are import-ant tools in the current restructured electricity markets. Unfortunately, due to its stochastic nature, distribution systems faults are hardly avoidable. This paper proposes a novel fault diagnosis scheme for power distribution systems, composed by three different processes: fault detection and classification, fault location, and fault section determination. The fault detection and classification technique is wavelet based. The fault-location technique is impedance based and uses local voltage and current fundamental phasors. The fault section determination method is artificial neural network based and uses the local current and voltage signals to estimate the faulted section. The proposed hybrid scheme was validated through Alternate Transient Program/Electromagentic Transients Program simulations and was implemented as embedded software. It is currently used as a fault diagnosis tool in a Southern Brazilian power distribution company.

Decision making in fuzzy environment and multicriteria power engineering problems

This paper presents results of research into the use of the Bellman-Zadeh approach to decision making in a fuzzy environment for solving multicriteria power engineering problems. The application of the approach conforms to the principle of guaranteed result and provides constructive lines in computationally effective obtaining harmonious solutions on the basis of solving associated maxmin problems. The presented results are universally applicable and are already being used to solve diverse classes of power engineering problems. It is illustrated by considering problems of power and energy shortage allocation, power system operation, optimization of network configuration in distribution systems, and energetically effective voltage control in distribution systems. (c) 2011 Elsevier Ltd. All rights reserved.

Hardness and structure characterization of Ti(6)Al(4)V films produced by reactive magnetron sputtering on a conventional austenitic stainless steel

Ti(6)Al(4)V thin films were grown by magnetron sputtering on a conventional austenitic stainless steel. Five deposition conditions varying both the deposition chamber pressure and the plasma power were studied. Highly textured thin films were obtained, their crystallite size (C) 2008 Elsevier Ltd. All rights reserved.

Electro-optically sensitive diamond-like carbon thin films deposited by reactive magnetron sputtering for electronic device applications

The goal of this work is to study and relate electrical and optical properties of diamond-like carbon (DLC) thin films for applications in electronic devices. DLC films were deposited in a reactive RF magnetron sputtering system on p-type silicon and glass substrates. The target was a 99.9999% pure, 6 in. diameter graphite plate and methane was used as processing gas. Eight DLC films were produced for each substrate, varying deposition time, the reactor pressure between 5 mTorr and 10 mTorr while the RF power was applied at 13.56 MHz and varied between 100, 150, 200 and 250W. After deposition, the films were analyzed by I-V and C-V measurements (Cheng et al. (2004) [1]) in order to determine the electric resistivity, photo-current response and dielectric constant, optical transmittance, used to find the optical gap by the Tauc method; and by photoluminescence analysis to determine the photoemission and confirm the optical band gap. These characteristics are compared and the influence of the deposition parameters is discussed. (C) 2011 Published by Elsevier B.V.

Low-temperature deposition of silicon oxide and silicon nitride by reactive magnetron sputtering

In this study, oxide and nitride films were deposited at room temperature through the reaction of silicon Sputtered by argon and oxygen ions or argon and nitrogen ions at 250 and 350 W with 0.67 Pa pressure. It was observed that for both thin films the deposition rates increase with the applied RF power and decrease with the increase of the gas concentration. The Si/O and Si/N ratio were obtained through RBS analyses and for silicon oxide the values changed from 0.42 to 0.57 and for silicon nitride the Values changed from 0.4 to 1.03. The dielectric constants were calculated through capacitance-voltage curves with the silicon oxide values varying from 2.4 to 5.5, and silicon nitride values varying from 6.2 to 6.7, which are good options for microelectronic dielectrics. (c) 2008 Elsevier Ltd. All rights reserved.

Development and fabrication of an optimized thermo-electro-optic device using a Mach-Zehnder interferometer

The development and fabrication of a thermo-electro-optic sensor using a Mach-Zehnder interferometer and a resistive micro-heater placed in one of the device`s arms is presented. The Mach-Zehnder structure was fabricated on a single crystal silicon substrate using silicon oxynitride and amorphous hydrogenated silicon carbide films to form an anti-resonant reflective optical waveguide. The materials were deposited by Plasma enhanced chemical vapor deposition technique at low temperatures (similar to 320 degrees C). To optimize the heat transfer and increase the device response with current variation, part of the Mach-Zehnder sensor arm was suspended through front-side bulk micromachining of the silicon substrate in a KOH solution. With the temperature variation caused by the micro-heater, the refractive index of the core layer of the optical waveguide changes due to the thermo-optic effect. Since this variation occurs only in one of the Mach-Zehnder`s arm, a phase difference between the arms is produced, leading to electromagnetic interference. In this way, the current applied to the micro-resistor can control the device output optical power. Further, reactive ion etching technique was used in this work to define the device`s geometry, and a study of SF6 based etching rates on different composition of silicon oxynitride films is also presented. (C) 2007 Elsevier B.V. All rights reserved.

Postural control during kneeling

Postural control was studied when the subject was kneeling with erect trunk in a quiet posture and compared to that obtained during quiet standing. The analysis was based on the center of pressure motion in the sagittal plane (CPx), both in the time and in the frequency domains. One could assume that postural control during kneeling would be poorer than in standing because it is a less natural posture. This could cause a higher CPx variability. The power spectral density (PSD) of the CPx obtained from the experimental data in the kneeling position (KN) showed a significant decrease at frequencies below 0.3 Hz compared to upright (UP) (P < 0.01), which indicates less sway in KN. Conversely, there was an increase in fast postural oscillations (above 0.7 Hz) during KN compared to UP (P < 0.05). The root mean square (RMS) of the CPx was higher for UP (P < 0.01) while the mean velocity (MV) was higher during KN (P < 0.05). Lack of vision had a significant effect on the PSD and the parameters estimated from the CPx in both positions. We also sought to verify whether the changes in the PSD of the CPx found between the UP and KN positions were exclusively due to biomechanical factors (e.g., lowered center of gravity), or also reflected changes in the neural processes involved in the control of balance. To reach this goal, besides the experimental approach, a simple feedback model (a PID neural system, with added neural noise and controlling an inverted pendulum) was used to simulate postural sway in both conditions (in KN the pendulum was shortened, the mass and the moment of inertia were decreased). A parameter optimization method was used to fit the CPx power spectrum given by the model to that obtained experimentally. The results indicated that the changed anthropometric parameters in KN would indeed cause a large decrease in the power spectrum at low frequencies. However, the model fitting also showed that there were considerable changes also in the neural subsystem when the subject went from standing to kneeling. There was a lowering of the proportional and derivative gains and an increase in the neural noise power. Additional increases in the neural noise power were found also when the subject closed his eyes.

Thermodynamic information system for diagnosis and prognosis of power plant operation condition

A thermodynamic information system for diagnosis and prognosis of an existing power plant was developed. The system is based on an analytic approach that informs the current thermodynamic condition of all cycle components, as well as the improvement that can be obtained in the cycle performance by the elimination of the discovered anomalies. The effects induced by components anomalies and repairs in other components efficiency, which have proven to be one of the main drawbacks in the diagnosis and prognosis analyses, are taken into consideration owing to the use of performance curves and corrected performance curves together with the thermodynamic data collected from the distributed control system. The approach used to develop the system is explained, the system implementation in a real gas turbine cogeneration combined cycle is described and the results are discussed. (C) 2011 Elsevier Ltd. All rights reserved.

Effect of the Gamma Radiation Dose Rate on Psychrotrophic Bacteria, Thiobarbituric Acid Reactive Substances, and Sensory Characteristics of Mechanically Deboned Chicken Meat

Frozen samples of mechanically deboned chicken meat (MDCM) with skin were irradiated with gamma radiation doses of 0.0 kGy (control) and 3 kGy at 2 different radiation dose rates: 0.32 kGy/h (3 kGy) and 4.04 kGy/h (3 kGy). Batches of irradiated and control samples were evaluated during 11 d of refrigerated (2 +/- 1 degrees C) storage for the following parameters: total psychrotrophic bacteria count, thiobarbituric acid reactive substances (TBARS), evaluation of objective color (L*, a*, and b*) and a sensory evaluation (irradiated odor, oxidized odor, pink and brown colors). No statistical difference (P > 0.05) was found amongst the TBARS values obtained for the MDCM samples irradiated with dose rates of 0.32 and 4.04 kGy/h. There was a significant increase (P < 0.05) in the psychrotrophic bacterial count as from the 7th day of refrigerated storage, for the MDCM samples irradiated at the dose rate of 4.04 kGy/h. With respect to the attribute of oxidized odor, the samples irradiated with a dose rate of 0.32 kGy/h showed a stronger intensity and were significantly different (P < 0.05) from the sample irradiated with a dose rate of 4.04 kGy/h on days 0 and 2 of refrigerated storage. Irradiation with a dose rate of 4.04 kGy/h (3 kGy) was shown to be the best condition for the processing of MDCM according to the evaluation of all the variables, under the conditions of this study. Practical Application The results obtained for the application of different dose rates of ionizing radiation to mechanically deboned chicken meat will provide the food industry with information concerning the definition of the best processing conditions to maximize the sensory and food quality.

Circulating Interleukin-6 and High-Sensitivity C-Reactive Protein Decrease After Periodontal Therapy in Otherwise Healthy Subjects

Background: Periodontal disease has been associated with many chronic inflammatory systemic diseases, and a common chronic inflammation pathway has been suggested for these conditions. However, few studies have evaluated whether periodontal disease, in the absence of other known inflammatory conditions and smoking, affects circulating markers of chronic inflammation. This study compared chronic inflammation markers in control individuals and patients with periodontal disease and observed whether non-surgical periodontal therapy affected inflammatory disease markers after 3 months. Methods: Plasma and serum of 20 controls and 25 patients with periodontal disease were obtained prior to and 3 months after non-surgical periodontal therapy. All patients were non-smokers, they did not use any medication, and they had no history or detectable signs and symptoms of systemic diseases. Periodontal and systemic parameters included probing depth, bleeding on probing, clinical attachment level, hematologic parameters, as well as the following inflammatory markers: interleukin (IL)-6, high-sensitivity C-reactive protein (hs-CRP), CD40 ligand, monocyte chemoattractant protein (MCP)-1, soluble P-selectin (sP-selectin), soluble vascular adhesion molecule (sVCAM)-1, and soluble intercellular adhesion molecule (sICAM)-1. Results: There were no differences in the hematologic parameters of the patients in the control and periodontal disease groups. Among the tested inflammatory markers, IL-6 concentrations were higher in the periodontal disease group at baseline compared to the controls (P=0.006). Therapy was highly effective (P<0.001 for all the analyzed clinical parameters), and a decrease in circulating IL-6 and hs-CRP concentrations was observed 3 months after therapy (P=0.001 and P=0.006, respectively). Our results also suggest that the CD40 ligand marker may have been different in the control and periodontal disease groups prior to the therapy (P=0.009). Conclusions: In apparently otherwise healthy patients, periodontal disease is associated with increased circulating concentrations of IL-6 and hs-CRP, which decreased 3 months after non-surgical periodontal therapy. With regard to the CD40 ligand, MCP-1, sP-selectin, sVCAM-1, and sICAM-1, no changes were seen in the periodontal disease group between baseline and 3 months after therapy. J Periodontol 2009;80:594-602.

Impact of clinical varicocele and testis size on seminal reactive oxygen species levels in a fertile population: a prospective controlled study

Objective: To investigate: 1) the impact of clinical varicocele on reactive oxygen species (ROS) levels in neat and washed semen in a proven fertile population; and 2) the correlation between ROS levels, testicular volume, and varicocele grade in the same population of fertile men. Design: Prospective controlled clinical study. Setting: Andrology laboratory at tertiary-care hospital. Patient(s): One hundred fourteen healthy fertile men (81 normal fertile and 33 fertile with clinical varicocele) and 30 infertile patients (control subjects). Intervention(s): Standard semen analysis and measurement of sperm ROS production. Main Outcome Measure(s): Seminal parameters, seminal ROS levels, seminal leukocyte levels, clinical varicocele, and testis size. Result(s): Thirty-three of the 11.4 (29%) fertile men had clinical varicocele (grade 1, n = 14; grade 2, n = 11; and grade 3, n = 8), and the remaining 81 (71%) had a normal physical examination. Levels of ROS and semen quality did not differ significantly between the fertile men with or without varicocele. No significant differences in ROS levels in neat and washed semen were observed compared with fertile men with grades 2 and 3 varicocele and with fertile men with varicocele grade 1. The ROS levels in neat and washed semen were not significantly correlated with varicocele grade in fertile men. No significant correlations between ROS levels and testis volume were observed between the fertile groups. Conclusion(s): The presence of clinical varicocele in fertile men is not associated with higher seminal ROS levels or abnormal semen parameters. Levels of ROS are not correlated with varicocele grade or testis volume in the same population of fertile men.

Passive Acquisition of Protective Antibodies Reactive with Bordetella pertussis in Newborns via Placental Transfer and Breast-feeding

Although acquisition of anti-pertussis antibodies by the newborn via placental transfer has been demonstrated, a subsequent recrudescence of pertussis infection is often observed, particularly in infants. The present study investigated the passive transfer of anti-pertussis IgG and IgA antibodies to term newborns and their ability to neutralize bacterial pathogenicity in an in vivo experimental model using mice intracerebrally challenged with viable Bordetella pertussis. Forty paired samples of maternal/umbilical cord sera and colostrum were obtained. Anti-pertussis antibodies were analysed by immunoenzymatic assay and by Immunoblotting. Antibody neutralizing ability was assessed through intracerebral B. pertussis challenges in mice. Anti-pertussis IgG titres were equivalent in both maternal and newborn sera (medians = 1:225 and 1:265), with a transfer rate of 118%. The colostrum samples had variable specific IgA titres (median = 1:74). The immunoblotting assays demonstrated identical recognition profiles of paired maternal and newborn serum pools but different bacterial recognition intensities by colostrum pools. In the animal model, significant differences were always observed when the serum and colostrum samples and pools were compared with the positive control (P < 0.05). Unlike samples with lower anti-pertussis titres, samples with high titres showed protective capacities above 50%. Pertussis-absorbed serum and colostrum pools protected 30% of mice and purified IgG antibodies protected 65%. Both pooled and single-sample protective abilities were correlated with antibody titres (P < 0.01). Our data demonstrated the effectiveness of anti-pertussis antibodies in bacterial pathogenesis neutralization, emphasizing the importance of placental transfer and breast-feeding in protecting infants against respiratory infections caused by Bordetella pertussis.

Acute inflammatory response secondary to intrapleural administration of two types of talc

Intrapleural instillation of talc has been used in the treatment of recurrent pleural effusions but can, in rare instances, result in respiratory failure. Side-effects seem to be related to composition, size and inflammatory power of talc particles. The aim of this study was to evaluate the inflammatory response to intrapleural injection of talc containing small particles (ST) or talc containing particles of mixed size (MT). 100 rabbits received intrapleural talc, 50 with ST (median 6.41 mu m) and 50 with MT median 21.15 mu m); the control group was composed of 35 rabbits. Cells, lactate dehydrogenase, C-reactive protein (CRIP), interleukin (IL)-8 and vascular endothelial growth factor were evaluated in serum and bronchoalveolar lavage at 6, 24, 48, 72 and 96 h. Lung histology and the presence of talc were also analysed. Statistics were performed using ANOVA and an unpaired t-test. Most of the parameters showed greater levels in the animals injected with talc than in the controls, suggesting a systemic and pulmonary response. Higher serum levels of CRP and IL-8 were observed in the animals injected with ST. Talc particles were observed in both lungs with no differences between groups. Lung cell infiltrate was more evident in the ST group. In conclusion, talc with larger particles should be the preferred choice in clinical practice in order to induce safer pleurodesis.

Frequency of HLA-B27 and its alleles in patients with Reiter syndrome: comparison with the frequency in other spondyloarthropathies and a healthy control population

This retrospective study analyzed the HLA-B*27 alleles in a group of 20 consecutive patients with the diagnosis of Reiter syndrome (RS) followed in a tertiary referral university hospital in Brazil, during the period 1990-2006, and compared the data with that observed in other patients with spondyloarthropathies followed at the same institution. Eight cases were associated to gastrointestinal infection, eight cases to previous urethritis, and four cases presented no established preceding infection. HLA-B*27 alleles were typed by polymerase chain reaction-amplified DNA hybridized with sequence-specific oligonucleotide probes (HLA-B*2701 to HLA-B*2721). They were compared to a group of 108 patients with ankylosing spondylitis (AS), 40 with undifferentiated spondyloarthropathy (uSpA) and 111 healthy controls. Among the 20 patients, 17 were HLA-B*27 positive (85%). Two HLA-B*27 alleles were observed: HLA-B*2705 (65%) and HLA-B*2702 (35%). In the other spondyloarthropathies, the observed alleles were HLA-B*2705 (90% in AS and 92.5% in uSpA), HLA-B*2702 (8% in AS and 5% in uSpA), HLA-B*2704 (1% in AS and 2.5% in uSpA) and HLA-B*2713 (1% in AS). Among the 111 healthy controls, 80% presented HLA-B*2705, followed by HLA-B*2702 in 10%, HLA-B*2703 in 6%, HLA-B*2707 in 3% and HLA-B*2713 in 1%. Concluding, in the HLA-B*27 positive patients with RS in this study there was predominance of HLA-B*2705 allele, in a lower frequency than that observed in patients with other spondyloarthropathies and healthy controls.